PINARELLO OLIMPIC Guide
USER MANUAL AND MAINTENANCE
OLIMPIC
EXTENTION BAR
2
1. SIZE CHART
UCI RULES – CLASS MAX REACH – SIZE 310
BOLIDE F HR
BOLIDE F TT
These measurements were obtained with the bicycle in a horizontal position, with extensions
inclined at 20° and at maximum extension. To obtain the nal reach measurement, all the changes
explained below that may have been made starting from this standard conguration must be
added. All these measures do not include any commands or handcaps.
FRAME SIZE STEM LENGTH [mm] EXTENSION SIZE [mm] REACH [mm]
450 120 310 801
525 120 310 827
550 120 310 855
FRAME SIZE STEM LENGTH [mm] EXTENSION SIZE [mm] REACH [mm]
450 100 310 784
485 100 310 801
520 120 310 838
550 120 310 855
3
IT
UCI RULES – CLASS MAX REACH – SIZE 285
BOLIDE F HR
BOLIDE F TT
These measurements were obtained with the bicycle in a horizontal position, with extensions
inclined at 20° and at maximum extension. To obtain the nal reach measurement, all the changes
explained below that may have been made starting from this standard conguration must be
added. All these measures do not include any commands or handcaps.
FRAME SIZE STEM LENGTH [mm] EXTENSION SIZE [mm] REACH [mm]
450 120 285 778
525 120 285 804
550 120 285 832
FRAME SIZE STEM LENGTH [mm] EXTENSION SIZE [mm] REACH [mm]
450 100 285 761
485 100 285 778
520 120 285 815
550 120 285 832
4
EXTENSION SLOPE ADJUSTMENT – SIZE 310
Rotation of the extensions between 10° and 30° with dened intervals of 5° is allowed. Changing
the inclination causes a change in the total reach.
EXTENSION ANGLE [°] EXTENSION SIZE [mm] REACH GAIN [mm]
10 310 +14
15 310 +8
20 310 0
25 310 -11
30 310 -24
5
IT
EXTENSION SLOPE ADJUSTMENT – SIZE 285
Rotation of the extensions between 10° and 30° with dened intervals of 5° is allowed. Changing
the inclination causes a change in the total reach.
EXTENSION ANGLE [°] EXTENSION SIZE [mm] REACH GAIN [mm]
10 285 +13
15 285 +8
20 285 0
25 285 -10
30 285 -22
6
EXTENSION SLIDER ADJUSTMENT
HANDGRIP CUT ADJUSTMENT
Continuous translation of the extensions is allowed up to a maximum of 25mm. The dierence in
reach gained based on the inclination of the extensions is negligible.
The handrips can be shortened up to the minimum mark located 20mm from the tip. The
maximum reduction involves a shortening of the reach by 10mm.
7
IT
UCI RULES – CLASS MAX DROP
ARMREST POSITION ADJUSTMENT
These results were obtained with the original handgrip. All these measures do not include any
commands or handcaps. The table is valid for sizes 310 and 285.
The position of the pads can vary along the direction of development of the extensions in steps of
11.25mm up to a maximum of 67.5mm between the two limit positions.
10° 15° 20° 25° 30°
UCI CLASS 1 ALLOWED ALLOWED ALLOWED NOT ALLOWED NOT ALLOWED
UCI CLASS 2 ALLOWED ALLOWED ALLOWED ALLOWED NOT ALLOWED
UCI CLASS 3 ALLOWED ALLOWED ALLOWED ALLOWED ALLOWED
8
EXTENSION WIDTH ADJUSTMENT
The convergence angle of the extensions is dened as 5°. The width of the extensions varies with
25mm steps given by the holes on the basebar.
*disponibili solo per Bolide F TT
CONVERGENCE [°] W [mm]
590
5115
5140
5 *165
5 *190
9
IT
MIDDLE POINT OFTHE PADS REACH AND STACK (upper face of the pads)
Starting point with inclination adjuster and 5 mm shaped spacer.
Variation of the Stack value depending on the version of handlebar used and width of the
extensions.
It is possible to add a maximum number of spacers to increase the Stack equal to +45 mm and
change the shaped spacer to gain +15 mm. The change in inclination partially contributes to
varying both the Reach and Stack values of the pad.
BOLIDE F HR
BOLIDE F TT
FRAME SIZE STEM LENGTH [mm] STACK [mm] REACH [mm]
450 120 588 516
525 120 610 542
550 120 625 570
FRAME SIZE STEM LENGTH [mm] STACK [mm] REACH [mm]
450 100 579 499
485 100 598 516
520 120 613 553
550 120 625 570
W [mm] CURVED HANDLEBAR [mm] FLAT HANDLEBAR [mm]
90 0 0
115 -2 0
140 -4 0
165 -6 0
190 -8 0
10
2. ASSEMBLY INSTRUCTIONS
Perform the assembly by following the four steps outlined below.
11
IT
WARNING
Use the best combination of washers and screws provided to engage the thread as much as
possible. Once this step is completed, visually check before proceeding: the holes threaded parts
must not be empty and the screws must not protrude.
12
13
IT
OLYMPIC EXTENSION BAR – PASSAGGIO CAVI Di2
pinarello.com
Table of contents
