Pinnacle Gable Series User manual

GARDENSHED
2.99W x 2.99D x 2.19Hm
Tools required: Drill, measuring tape, Phillips-head screw driver, rivet gun, rubber mallet, sturdy ladder, shifting spanner, 2 saw horses, 3mm
steel drill bit, 4mm steel drill bit and a 10mm masonry drill bit.
Assembly instructions
Gable Series
Congratulations on purchasing your new Pinnacle garden shed. Before assembling, we recommend
you read the instructions thoroughly. Your new garden shed comes with pre-drilled holes to make
assembly quicker. We recommend you assemble it using a trestle table or sawhorses and planks.
This will ensure that you are working o the ground and make it easier for you.
Assembly of this shed is a three-person job and should not be attempted in windy conditions.
Check out our
shed building
tips on YouTube!
AU: 1800 349 776
NZ: 09 276 4071
www.pinnacle.net.au

GARDENSHED2.99W x 2.99D x 2.19Hm
2
Outer base dimensions 2995 x 2995 mm
Inner base dimensions 2950 x 2950 mm
Wall height 1800 mm
Peak height 2195 mm
Roof width 3100 mm
Door opening dimensions 1740 x 1518 mm
Dimension overview:

Build your garden shed in 7 easy steps!
Step 1: Check all parts against the component list
Step 2: Assemble the rear wall panels
Step 3: Assemble the side wall panels
Step 4: Assemble the roof panels
Step 5: Assemble the front wall panel
Step 6: Assemble the front door
Step 7: Fit the panels together
Warning: Do not assemble this shed on a windy day.
Warning: This shed must be fully assembled and anchored to a concrete slab using the supplied bolt down kit in one session/
day. The shed must not be left partly assembled.
Assembly recommendations: We recommend a minimum of three people are needed to assemble this shed.
100mm
Concrete slab: Please ensure that your site is level. It is recommended that your slab is
100mm thick and you use builder’s plastic and F52 reinforcing mesh. We recommend that
you make your slab 100mm bigger than the base dimensions of your garden shed. This will
allow for a 50mm edge around your garden shed. We recommend that you slope the 50mm
edges downward by 10mm so that rainwater can drain away from your garden shed.
WARNING: If you require a cyclonic kit for this shed please note, you will need to assemble the kit and shed together.
CONCRETE SLAB: 3095mm
CONCRETE SLAB: 3095mm

GARDENSHED2.99W x 2.99D x 2.19Hm
4
Picture Description Component Location Part
No. QTY BOX Check
Sheet Sheet 1880x770mm Rear wall
Side wall 18M 12 1
Sheet Sheet 1579x770mm Roof S30 2 2
Sheet Sheet 1579x770mm Roof S31 2 2
Sheet Sheet 1579x770mm Roof S32 4 2
Sheet Sheet 1800x717mm Front S94 1 2
Sheet Sheet 1800x717mm Front S95 1 2
Door Sheet Sheet 1743x770mm Door D18R 1 2
Door Sheet Sheet 1743x770mm Door D18L 1 2
Channel Channel 1743mm Door M24 1 1
Channel Channel 1743mm Door M25 1 1
Channel Channel 1743mm Door M41 1 1
Step 1: Check all parts against the component list
Lay out all parts with number facing outwards and check o against parts list.

5
Picture Description Component Location Part
No. QTY BOX Check
Channel Channel 768mm Door M26 2 2
Channel Channel 764mm Door M27 1 2
Channel Channel 764mm Door M28 1 2
Jamb Jamb 1743mm Door J20 1 1
Brace Brace 1075mm Door U11 4 2
Channel Channel 1494mm Side wall
roof 27A 4 1
Channel Channel 1494mm Side wall
roof 27B 4 1
Channel Channel 1494mm Rear wall 27C 1 1
Channel Channel 1494mm Rear wall 27D 1 1
Channel Channel 1494mm Roof 27E 2 1
Channel Channel 1494mm Roof 27F 2 1
Channel Channel 1494mm Rear wall 27H 1 1

GARDENSHED2.99W x 2.99D x 2.19Hm
Picture Description Component Location Part
No. QTY BOX Check
Channel Channel 1494mm Rear wall 27I 1 1
Channel Channel 1494mm Side wall 27J 2 1
Channel Channel 1494mm Side wall 27K 2 1
Channel Channel 1494mm Front 27L 1 2
Channel Channel 1494mm Front 27M 1 2
Channel Channel 1494mm Front 27N 1 2
Channel Channel 1494mm Front 27P 1 2
Channel Channel 1549mm Front 28 1 2
Channel Channel 674mm Front 33R 1 2
Channel Channel 674mm Front 33L 1 2
Channel Channel 1468mm Side wall
Rear wall 35R 3 2
Channel Channel 1468mm Side wall
Rear wall 35L 3 2
Jamb Jamb 1798mm Front J3 1 1
Jamb Jamb 1798mm Front J4 1 1

Picture Description Component Location Part
No. QTY BOX Check
Jamb Jamb 1549mm Front 43 1 2
Corner Brace Brace 1798mm Corners Z43 4 2
Lip Lip 1582mm Roof L4 4 2
Gable Cap Gable cap 1495mm Roof E4 2 2
Connector Gable cap connector
450mm Roof E3 1 2
Ridge Beam Ridge beam
1495mm zinc Roof 73 2 1
Gable R/H Gable 1470mm Roof G7 2 2
Gable L/h Gable 1470mm Roof G8 2 2
Logo Cap Logo cap Roof 95 2 2
Roof Brace Roof brace zinc Roof 96 2 1
Ridge Beam
Connector
Ridge beam connector
450mm zinc Roof 67 1 1
Channel
Connector
Channel connector
188mm Side wall 66 11 2
Joining
Brace Brace Door W 2 2

GARDENSHED2.99W x 2.99D x 2.19Hm
8
Qty checking date: ____ / ____ / _____
Qty checking personal badge number: _______________
Signature: _________________________________________
In the unlikely event that you nd you are missing a part, Australian customers please contact Pinnacle on 1800 349 776. New Zealand
customers please contact Harco (Harkness & Young Ltd) on: 09 276 4071. A copy of proof of purchase may be requested.
Note: All ttings are located in Box 2.
Fittings part list:
Picture Component QTY Picture Component QTY
Self-tapping screws (10mm) 420 Self-tapping screws (16mm) 35
4 x 10mm Rivet 20 3 x 10mm Rivet 70
Pad bolt (Part 70) 1 Keeper (Part 71) 2
65x65mm barrel bolt plate
(Part 75) 1 60mm barrel bolt (Part 74) 2
Mid wall brace bracket
(Part 72) 4 5/16 x 19mm Hexagonal bolt 11
5/16 Hexagonal Nut 11 Base bracket 11
Mid wall channel connector 3 Self tapper safety cover 40
Channel safety cover
(L type) 1Channel safety cover (R type) 1
Plastic stopper 8 Sleeve anchor bolt 11

9
Garden shed overview:
18M
S31
27D
27C
27A
27B
27J
27K
27B
27E
27E
27F
27F
27H
27I
27J
27P
27N
27M
27L
28
35R
35L
35R
35L
35R
33R
33L
27B
27A
35L
43
66
66
66
96
72
66
27K
S94
96
L4
27A
66 73
E4
66
L4
66 73
E4
67
E3
L4
L4
27B
27A
66
71
66
66
S95
S32
S32
S30
S30
S32
S32
S31
G7
G8
G7
G8
Z43
95
95
Z43
Z43
Z43
18M
18M
18M
18M
18M
18M
18M
18M
18M
18M
18M
J4 J3
74
74
M28
M27
W
71
D18L
M41
M25
M24
M26
M26
W
70
75
J20
D18R
U11
U11
U11
U11

GARDENSHED2.99W x 2.99D x 2.19Hm
10
Step 2: Assemble the rear wall panels
You will nd it easier to assemble your shed using sawhorses with timber studs attached (timber needs to be the same length as the
shed ( 3.0 m)) or alternatively, a trestle table.
Place 4 x part 18M (sheeting) on your work table and join together with self-tapping screws as per the diagram below.
ROOF TOP EDGE RIDGES FACING UP
18M
18M
18M
18M

11
Step 2: Assemble the rear wall panels (continued)
Now t parts 27I and 27H (top channel) and parts 27C and 27D (bottom channel) to the sheeting by tapping it in ( diagram A ) or sliding it in (
diagram B ). Make sure the small lip of the channel is always facing out. This ensures rain water cannot build up inside your shed. Make sure
parts 27I and 27H are used as top side channels as per diagram A below.
Tip: If panel and screw holes do not line up, try pulling panel to match up holes.
27I
27H
27C
27D
RIDGES FACING UP
RIDGES FACING UP
27I
27H
27C
27D
A
B
ROOF TOP EDGE
ROOF TOP EDGE
18M
18M
18M
18M
18M
18M
18M
18M

GARDENSHED2.99W x 2.99D x 2.19Hm
12
Step 2: Assemble the rear wall panels (continued)
Now x parts 35R and 35L (mid wall channels) joined by mid wall channel connector to the sheeting with self-tapping screws. Please note
that the groove should face downwards. Fix other channels with self-tapping screws. TIP (before applying connectors): to help panel and
screw holes to line up, fasten screws one at a time from one side of the wall to the other and pull panel away from screw each time to match
up holes. Apply part 66 (channel connector) on top and bottom channels to enhance the strength. NOTE: Screws are applied to both sides
of the connectors. All screws marked with a cross should not be xed at this stage.
35L
27H
27I
27D
27C
35R 66
66
35L
35R
66
Midwall channel
connector
RIDGES FACING UP
RIDGES FACING DOWN
TOP
TOP

13
Step 3: Assemble the side wall panels
Place 4 x part 18M (sheeting) on your worktable and join together with self-tapping screws as per the diagram below. Now t parts
27K and 27J (top channel) and parts 27A and 27B (bottom channel) to the sheeting by tapping or sliding it in. Make sure the small
lip of the channel is always facing out. This ensures rainwater cannot build up inside your shed. Make sure parts 27K and 27J are
used as top side channels. TIP (before applying connectors): to help panel and screw holes to line up, fasten screws one at a time
from one side of the wall to the other and pull panel away from screw each time to match up holes. Now x parts 35R and 35L
(mid wall channels) joined by a mid wall channel connector to the sheeting with self-tapping screws. NOTE: the groove should face
downwards. Fix channels with self-tapping screws and apply part 66 (channel connectors) to enhance the structural strength. Note
that screws are applied to both sides of the connectors.
RIDGES FACING UP
ROOF TOP EDGE
18M
18M
18M
18M

GARDENSHED2.99W x 2.99D x 2.19Hm
14
Step 3: Assemble the side wall panels (continued)
All screws marked with a cross should not be xed at this stage. Repeat the same steps for the other side wall. Make sure the small
lip of the channel is always facing out. This ensures rain water cannot build up inside your shed.
RIDGES FACING DOWN
TOP

15
Step 4: Assemble the roof panel
Place parts S30, S31 and 2 x part S32 (sheeting) on your worktable and join together with self-tapping screws as per the
diagram below.
Fix parts 27F, 27E, 27A and 27B (channels) using self-tapping screws as per the diagram below. Please ensure parts 27A and 27B are
attached to the side of the sheeting which has pre-punched holes as per the diagram below. Make sure the small lip of the channel is
always facing out. This ensures rain water cannot build up inside your shed.
Enhance the structural strength by applying part 66 (channel connectors). Note that screws are applied to both sides of the connectors
as per Step 3.
S32
S30
S32
S31
RIDGES FACING UP
RIDGES FACING UP
ROOF TOP EDGE

GARDENSHED2.99W x 2.99D x 2.19Hm
16
Step 4: Assemble the roof panel (continued)
Leave 4 corners unxed in this stage. Repeat the same steps for the other roof panel.
ROOF TOP EDGE

17
Step 5: Assemble the front wall panels
Fix parts J3 and J4 (jamb) to parts S94 and S95 (sheeting) with self-tapping screws. NOTE: All screws marked with a cross should not
be xed at this stage.
Fix parts 27P and 27N (top channels), part 43 (jamb), and parts 27L, 27M, and 28 (bottom channels) using self-tapping screws.
Enhance the top channels by applying part 66 (channel connector) and x screws through both sides. NOTE: for parts 27P, 27N, 27L
and 27M the small lip should be facing out to stop water building up and leaking into shed.
27M
27N
28
43
27L
27P
66
28
27M
27L
RIDGES FACING UP
RIDGES FACING UP
ROOF TOP EDGE
ROOF TOP EDGE
Note: Holes drilled in the edge of this
sheet are not a defect. They are there
to allow the door hinge rivets clearance
through this sheet.
J4
S94
J3
S95
S94
S95

GARDENSHED2.99W x 2.99D x 2.19Hm
18
Step 5: Assemble the front wall panels (continued)
Now x parts 33R and 33L (mid wall channels) to the sheeting using self-tapping screws. Please note the groove should
face downwards.
33R
33L
RIDGES FACING UP
ROOF TOP EDGE

19
Step 6: Assemble the front door
Place part D18R (door sheet) on the worktable. Fit 2 x part M26 and parts M24 and M25 (channels) to the door panel and x with
3.0 x 10mm rivets as per the diagrams below. Please ensure channel M26 has the smaller lip facing outwards.
M26
M26
RIDGES FACING UP
ROOF TOP EDGE
FIX WITH 3.0 X 10MM RIVETS
FIX WITH 3.0 X 10MM RIVETS
D18R
M25
M24

GARDENSHED2.99W x 2.99D x 2.19Hm
20
Step 6: Assemble the front door (continued)
Now place D18L (door sheet) on the worktable. Fit parts M27, M28, M41 (channels) and part J20 (jamb) to the door panel and x with
3.0 x 10mm rivets as per the diagrams below. Please ensure channels M27 and M28 have the smaller lip facing outwards.
RIDGES FACING UP
J20
M41
D18L
M28
M27
ROOF TOP EDGE
FIX WITH 3.0 X 10MM RIVETS
FIX WITH 3.0 X 10MM RIVETS