PIONEER DJ DDJ-800 User manual

DDJ-800
DJ Controller
pioneerdj.com/support/
rekordbox.com
For FAQs and other support information for this product, visit the above site.
Operating Instructions (Quick Start Guide)

En
2
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1b_A1_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture. D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
The graphical symbol placed on the product
means alternating current.
The graphical symbol placed on the product
means direct current.
The graphical symbol placed on the product
means Class II equipment.
D3-8-2-4_A1_En
CAUTION
The switch on this unit will not completely shut off all
power from the AC outlet. Since the power cord serves
as the main disconnect device for the unit, you will need
to unplug it from the AC outlet to shut down all power.
Therefore, make sure the unit has been installed so that
the power cord can be easily unplugged from the AC
outlet in case of an accident. To avoid fire hazard, the
power cord should also be unplugged from the AC outlet
when left unused for a long period of time (for example,
when on vacation).
D3-4-2-2-2a*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).
D3-4-2-1-7c*_A2_En

En 3
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. D8-10-1-2_A1_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Product Name: DJ Controller
Model Number: DDJ-800
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 2050 W. 190th Street, Suite 100, Torrance, CA 90504, U.S.A.
Phone: [phone]
URL: http://www.pioneerelectronics.com
D8-10-4*_C1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe
level – a level that lets the sound come through clearly
without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing “comfort
level” adapts to higher volumes of sound, so what sounds
“normal” can actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level
BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound level,
set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t hear
what’s around you.
• Use caution or temporarily discontinue use in potentially
hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS
EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON PAGE 19 FOR FUTURE
REFERENCE.
D36-AP9-3*_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power cord
when your hands are wet as this could cause a short
circuit or electric shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the cord. Never
make a knot in the cord or tie it with other cords. The
power cords should be routed such that they are not likely
to be stepped on. A damaged power cord can cause a fire
or give you an electrical shock. Check the power cord once
in a while. When you find it damaged, ask your nearest
service center or your dealer for a replacement.
S002*_A1_En
When using this product, confirm the safety
information shown on the bottom of the unit.
D3-4-2-2-4_B1_En
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s right
to operate the equipment.
D8-10-2_A1_En
CAUTION
This product is evaluated in moderate climate
condition.
D3-8-2-1-7b_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 5 cm at rear, and 5 cm at each side).
D3-4-2-1-7d*_A1_En
[Supplied power cord]
The supplied power cord is designed specifically for
120 V. Do not use it with a voltage other than 120 V.
Doing so may cause a fire or electric shock.
D3-7-14_PDJ_A1_En

En
4
Contents
How to read this manual
!Thank you for purchasing this Pioneer DJ product.
This manual provides a brief description of the procedures up until
connecting the unit to your PC/Mac and outputting audio. For the
detailed procedures, refer to the “Operating Instructions” on the
Pioneer DJ site. Read both this manual and “Operating Instructions”
which include important information to be understood before using
this unit. In particular, be sure to read safety regulations.
!In this manual, names of buttons and terminals indicated on the
unit, names of menus in the PC/Mac screen, etc., are indicated
within square bracket ([]). (e.g. [File], [CUE] button, [PHONES]
output terminal)
!The screens and specifications of the software and the external
appearance and specifications of the hardware described in this
manual are subject to change without notice for improvement and
so may differ from those in the explanations of this manual.
!Depending on the operating system version, web browser settings,
etc., operation may differ from the procedures described in this
manual.
!The language on the screens of the software described in this
manual may differ from the language on the actual screens.
Before start
Features ..............................................................................................5
Accessories.........................................................................................5
Viewing the manuals ...........................................................................5
rekordbox ............................................................................................6
Preparing rekordbox............................................................................6
Part names
Browser section...................................................................................7
Deck sections......................................................................................8
Mixer section .......................................................................................9
Rear panel.........................................................................................10
Front panel ........................................................................................10
Operation
Example of connections ....................................................................11
Connections ......................................................................................12
Starting the system............................................................................14
Turning off the system.......................................................................15
Changing the settings........................................................................15
Additional information
Troubleshooting ................................................................................16
Trademarks and registered trademarks............................................16
Cautions on copyrights......................................................................16
Specifications ....................................................................................17

En 5
Before start
Before start
Features
This unit is a DJ controller designed specifically for rekordbox dj. It is
equipped with features such as COLOR ON JOG DISPLAY, BEAT
FX DISPLAY, and JOG ADJUST to enable intuitive DJ performances
without looking at your laptop. In the player section and mixer section,
the buttons and knobs are arranged in the same layout as those on our
club standard set-up. The controller is lightweight and compact, so you
can take it wherever you go.
Accessories
Power cord
AC adapter
USB cable
Operating Instructions (Quick
Start Guide) (this document)
Warranty (The corresponding
information is provided on the
last page.) DDJ-800
DJ Controller
pioneerdj.com/support/
rekordbox.com
ForFAQs and other support information for this product, visit the above site.
Operating Instructions (Quick Start Guide)
rekordbox dj license key card
*For the latest information,
see the site below.
rekordbox.com
Note
The license key cannot be reis-
sued. Be careful not to lose it.
Viewing the manuals
Viewing the latest version of the “Operating
Instructions”
1 Launch a web browser on the PC/Mac and access the
Pioneer DJ site below.
pioneerdj.com
!To select your language, click the flag icon or GLOBAL icon on the
upper-right screen, and then select an area and language.
2 Click [Tutorials, manuals & documentation] under
[Support].
3 Click [DDJ-800] in the [DJ CONTROLLER] category.
4 Click the desired language from the Operating
Instructions list.
Download the manual as necessary.
Viewing “Introduction” / “Operating
Instructions” of rekordbox
!“Introduction” guides you through setting up rekordbox.
!“Operating Instructions” explains about track collection, EXPORT
mode, and PERFORMANCE mode.
1 Launch a web browser on the PC/Mac and access the
following site.
rekordbox.com
2 Click [Manual] under [Support].
3 Click the required language of “rekordbox
Introduction” or “Operating Instructions”.

En
6
rekordbox
!rekordbox
rekordbox is music management software for DJs to prepare tracks
and perform DJ play.
!rekordbox dj
The DJ performance function of rekordbox is called rekordbox dj.
rekordbox dj can be used by simply connecting the unit to a PC/
Mac. If you wish to use rekordbox dj on a PC/Mac without connect-
ing the unit, enter the license key shown on the rekordbox dj license
key card included with this product to use rekordbox dj.
*For the latest information, see the site below.
rekordbox.com
Operating environment
Supported operating systems CPU and required memory
Mac: Intel®processor Core™ i7, i5, i3
macOS Mojave 10.14
macOS High Sierra 10.13
macOS Sierra 10.12 4 GB or more of RAM
(latest update)
Windows: Intel®processor Core™ i7, i5, i3
Windows®10
Windows®8.1
Windows®7 4 GB or more of RAM
32-bit version or 64-bit version
(latest service pack)
Others
USB port A USB 2.0 port is required to connect the PC/Mac with
this unit.
Display resolution 1 280 x 768 or greater
Internet connection
An Internet connection is required for registering
the rekordbox user account and downloading the
software.
!Operation is not guaranteed on all PC/Mac, even if all the required operating
environment conditions indicated here are fulfilled.
!Depending on power saving settings, etc. of the PC/Mac, the CPU and hard
disk may not provide sufficient processing capabilities. For a laptop PC/Mac,
in particular, make sure the PC/Mac is in the proper conditions to provide
constant high performance (for example, by keeping the AC power connected)
when using rekordbox.
!A separate contract with an Internet service provider and payment of the
utilization fee are required to access the Internet.
!Use the latest version/service pack of the operating system.
!To check the latest information on the operating environment and compatibility
of rekordbox, and to acquire the latest operating system, refer to [System
requirements] under [Support] of the rekordbox product site below.
rekordbox.com
Preparing rekordbox
Install the software by following the procedure below when you use
rekordbox for the first time or if you are using rekordbox 4.x or an ear-
lier version.
If rekordbox Ver.5.x is already installed, update rekordbox to the lat-
est version using the Update Manager which is shown when starting
rekordbox.
Installing rekordbox
1 Launch a web browser on PC/Mac, open rekordbox
download page from the following site, and then
download rekordbox.
rekordbox.com
For Windows, select 32-bit or 64-bit version according to your PC.
2 Double-click the downloaded file to unzip it.
3 Double-click the unzipped file to launch the installer.
4 Carefully read the Software End User License
Agreement, and proceed with the installation by
following the instructions on the screen if you agree to
the terms.
!If you do not agree to the license agreement, cancel the
installation.
5 When the installation completion screen appears,
close the installer by following the instructions on the
screen.
The installation is completed.

En 7
Part names
Part names
For details on the functions of the various buttons and controls, see “Part names and functions” in the “Operating Instructions”.
1 Browser section
2 Deck sections
3 Mixer section
Browser section
32 4
1 LOAD button
2 BACK button
3 Rotary selector
4 VIEW button

En
8
Deck sections
This section is used to control the four decks. The buttons and controls for operating decks 1 and 3 are located on the left side of the controller, and
those for operating decks 2 and 4 are located on the right side of the controller.
42 5 76 83
9
a
b
c
d
e
jk
f g h i
l
m
o
r
p
s
q
n
1 LOOP IN/4 BEAT (IN ADJUST) button
2 LOOP OUT (OUT ADJUST) button
3 RELOOP/EXIT button
4 QUANTIZE button
5 CUE/LOOP CALL, c(LOOP 1/2X) button
6 CUE/LOOP CALL, d(LOOP 2X) button
7 DELETE button
8 MEMORY button
9 JOG FEELING ADJUST control
a BEAT SYNC button
b KEY SYNC button
c TEMPO RANGE button
d MASTER TEMPO button
e TEMPO slider
f HOT CUE mode button
g PAD FX1 mode button
h BEAT JUMP mode button
i SAMPLER mode button
j PAGE c, dbutton
k Performance pads
l PLAY/PAUSE fbutton
m CUE button
n TRACK SEARCH m, n/SEARCH button
o SHIFT button
p Jog dial display section
The LCD display is manufactured using extremely high precision
technology, but even so defective pixels (small number of black
dots or constantly lit red, blue, and green dots) may be visible on
some parts of the screen. Also, color unevenness and brightness
unevenness may be visible depending on the angle of view. These
phenomena are due to the characteristics of LCD displays and are
not an indication of a failure.
q Jog dial
r SLIP button
s SLIP REVERSE button

En 9
Part names
Mixer section
1 2 3 4 6 7 4
8
9
a
b
c
d
e
f
g
hijih
k
l
m
n
o
p
q
u
r rs s
t
5
1 MIC ON, OFF selector switch
2 Microphone indicator
3 PHONO/LINE, DECK3, DECK1 selector switch
4 TRIM control
5 Master level indicator
6 CLIP indicator
7 DECK2, DECK4, PHONO/LINE selector switch
8 MASTER LEVEL control
9 MASTER CUE button
a BOOTH LEVEL control
b Effect section display
c BEAT c, dbuttons
d BEAT FX SELECT control
e BEAT FX CH SELECT control
f BEAT FX LEVEL/DEPTH control
g BEAT FX ON/OFF button
h Headphones CUE button
i Channel fader
j Crossfader
k HEADPHONES LEVEL control
l HEADPHONES MIXING control
m SOUND COLOR FX SELECT buttons
n AUX TRIM control
o MIC EQ (HI, LOW) control
p MIC 2 LEVEL control
q MIC 1 LEVEL control
r EQ (HI, MID, LOW) control
s Channel level indicator
t SAMPLER LEVEL control
u COLOR control

En
10
Rear panel
1 2 3 4 5 7 769a ac fedg88 b
3
Top panel
1 DC cord hook
2 DC IN terminal
3 uswitch
Turns this unit on or puts this unit into standby mode.
4 BOOTH output terminals
5 MASTER 2 output terminals
6 MASTER 1 output terminals
!Be careful not to accidentally insert the power cord plug of
another product into an output terminal.
!Do not connect terminals capable of supplying phantom power
to the output terminals.
7 LINE/PHONO input terminals
8 LINE/PHONO switches
9 SIGNAL GND terminal
This terminal helps reduce noise when an analog player or other
device is connected.
a MIC attenuator
b MIC 1 input terminal
c MIC 2 input terminal
d AUX gain selector switch
e AUX input terminals
f USB terminal
g Kensington security slot
Front panel
1
1 PHONES output terminals
Do not use the two output terminals (one for a stereo phone jack
and one for a mini-phone jack) simultaneously. If a cable is con-
nected to or disconnected from one of the terminals while another
terminal is in use, the volume for the terminal in use may increase
or decrease unintentionally.

En 11
Operation
Operation
!Connect the power cord to a power outlet after all the connections are completed.
Turn off this unit and disconnect the power cord from the power outlet before connecting components or changing the connections.
Refer to the operating instructions for the components to be connected.
!Be sure to use the included power cord and AC adapter.
!Be sure to use the USB cable included with this product or one that conforms to USB 2.0.
!Do not use a USB hub.
Example of connections
Connecting input terminals
Rear panel
RL
RLRL
AUDIO OUT
R L
CONT
R
*1 Analog player
DJ player
*2 DJ player
Portable audio
device
Microphone
*2 DJ player
*1 Analog player
To power outlet
Power cord
(included)
AC adapter
(included)
PC/Mac
*1 When connecting an analog player, switch the [LINE/PHONO] switch beside the terminals to [PHONO].
*2 When connecting a DJ player, switch the [LINE/PHONO] switch beside the terminals to [LINE].

En
12
Connecting output terminals
Rear panel
Component, amplifier,
powered speaker, etc.
Power amplifier,
powered speakers, etc.
Power amplifier
(for booth monitor),
powered speakers, etc.
RL
Front panel
Headphones
!Be sure to use the [MASTER 1] output terminals for a balanced
output. If they are connected to an unbalanced input (such as RCA)
using an XLR to RCA converter cable (or converter adapter), etc.,
the sound quality may be lowered or noise may occur.
For connection with an unbalanced input (such as RCA), use the
[MASTER 2] output terminals.
!Be careful not to accidentally insert the power cord plug of
another unit into a [MASTER 1] output terminals.
Do not connect terminals capable of supplying phantom power
to the [MASTER 1] output terminals.
!Be sure to use the [BOOTH] output terminals for a balanced output.
If they are connected to an unbalanced input (such as an RCA or
TS terminal) with an TRS to RCA converter cable (or converter
adapter), TS cable, etc., the sound quality may be lowered or noise
may occur.
Connections
For more information on how to use this product with rekordbox dj,
refer to this product’s Operating Instructions that is available on the
Pioneer DJ site.
1 Connect headphones to the [PHONES] output
terminals.
2 Connect devices such as powered speakers, a
power amplifier, and components to the [MASTER 1] or
[MASTER 2] output terminals.
Powered speakers, etc.
!To output the sound from the [BOOTH] output terminals,
connect devices such as speakers to the [BOOTH] output
terminals.

En 13
Operation
3 Connect your PC/Mac to the unit via a USB cable.
USB cable
(included)
4 Turn on your PC/Mac.
5 Connect the AC adapter.
To power outlet
Power cord
㸦included㸧
AC adapter
(included)
6 Press the [u] switch on the rear panel of this unit to
turn this unit on.
This unit turns on.
!For Windows
The [Installing device driver software] message may appear
when this unit is first connected to the PC or when it is con-
nected to a different USB port on the PC. Wait a while until the
[Your devices are ready for use] message appears.
7 Turn on the devices connected to the output
terminals (powered speakers, power amplifier,
components, etc.).
!If a microphone, DJ player or other external device is connected
to the input terminals, turn on the connected device.

En
14
Starting the system
Launching rekordbox
It is necessary to register an account for using rekordbox.
For details about procedure, click [Manual] under [Support] of the fol-
lowing site, and then refer to “rekordbox Introduction”.
rekordbox.com
For Mac
Open the [Applications] folder in Finder and then double-click the
[rekordbox 5] > [rekordbox.app] icon.
For Windows 10
From the [Start] menu, click [Pioneer] > [rekordbox] icon.
For Windows 8.1
Click the [rekordbox] icon in [Apps view].
For Windows 7
From the [Start] menu, click [All Programs] > [Pioneer] >
[rekordbox 5.X.X] and the [rekordbox] icon.
Checking audio settings
Check that the [Audio] settings in [Preferences] of rekordbox are set
as follows.
For Mac
[Audio]: [DDJ-800]
[Output channels]:
[Master Output]: [DDJ-800: MASTER]
[Booth Output]: [DDJ-800: BOOTH]
[Headphones Output]: [DDJ-800: PHONES]
For Windows
[Audio]: [DDJ-800 ASIO]
[Output channels]:
[Master Output]: [DDJ-800 ASIO: MASTER]
[Booth Output]: [DDJ-800 ASIO: BOOTH]
[Headphones Output]: [DDJ-800 ASIO: PHONES]
!If PC MASTER OUT is enabled, the “+ Name of audio device in
PC/Mac” information will also be displayed after [MASTER] of the
[Master Output] item in the [Audio] settings.
Adding track files to [Collection]
A list of track files managed by rekordbox is displayed on the
[Collection] screen.
Registering the track files on the PC/Mac as the track collection of
rekordbox and then analyzing them enables those tracks to be used
with rekordbox.
1 Click [Collection] in the tree view.
A list of the tracks registered in [Collection] is displayed.
2 Open Finder (Mac) or Explorer (Windows), and drag
and drop track files or folders containing track files to
the track list.
The track files are added to [Collection], and the waveform analysis
of the track files starts. Wait until the analysis of all the track files is
finished.
Loading a track into a deck of the unit
This section explains how to load a track into Deck 1 (left) as an
example.
2
1
1 LOAD button
2 Rotary selector
Turn the rotary selector to select a track in [Collection]
and then press the [LOAD] button of deck 1 (left side).
The track is loaded into deck 1.

En 15
Operation
Play tracks
The following describes the procedure for outputting the sound of deck
1 (left side) as an example.
b
7
8
6
5
9
a
4
3
2
1
1 Channel level indicator
2 PHONO/LINE, DECK3, DECK1 selector switch
3 TRIM control
4 EQ (HI, MID, LOW) control
5 COLOR control
6 Headphones CUE button
7 HEADPHONES MIXING control
8 HEADPHONES LEVEL control
9 Channel fader
a Crossfader
b MASTER LEVEL control
1 Set the positions of the controls, etc., as shown
below.
Names of controls, etc. Operation
PHONO/LINE, DECK3, DECK1 selector switch [DECK1] position
TRIM control Turn it fully counterclockwise.
EQ (HI, MID, LOW) control Center position
COLOR control Center position
Channel fader Move it downward.
MASTER LEVEL control Turn it fully counterclockwise.
Crossfader Center position
2 Press the [PLAY/PAUSE f] button to play the
track.
3 Turn the [TRIM] control.
Adjust the [TRIM] control so that the channel level indicator’s orange
indicator lights at the peak level.
4 Move the channel fader upward.
5 Turn the [MASTER LEVEL] control to adjust the audio
level of the speakers.
Adjust the level of the sound output from the [MASTER 1] and
[MASTER 2] output terminals to an appropriate level.
!To output sound from the speakers of the PC/Mac, adjust not
the [MASTER LEVEL] control but the volume of the speakers of
the PC/Mac.
Monitoring channel audio with headphones
Set the positions of the controls, etc., as shown below.
Names of controls, etc. Operation
HEADPHONES MIXING control Center position
HEADPHONES LEVEL control Turn it fully counterclockwise.
1 Press the headphones [CUE] button.
2 Turn the [HEADPHONES LEVEL] control.
Adjust the level of sound output from the headphones to an appropriate
level.
Note
This unit and rekordbox dj include many functions to allow for more
individualistic DJ performances. For details on each function, access
the site below and see the “rekordbox Operating Instructions”.
rekordbox.com/manual
Turning off the system
1 Close rekordbox.
2 Press the [u] switch on the rear panel of this unit to
set the unit to standby.
3 Disconnect the USB cable from the PC/Mac.
Changing the settings
!For details on how to change the settings of this unit, refer to
“Changing the settings” in the Operating Instructions.

En
16
Additional information
Troubleshooting
!If you think that there is something wrong with this unit, check
the items in the “Troubleshooting” section of the “Operating
Instructions” of this unit or access the Pioneer DJ support page and
then check [FAQ] of DDJ-800.
pioneerdj.com/support/
Also, refer to [Support] > [FAQ] at the rekordbox product site.
rekordbox.com
Some problems occur due to the connected components. If the
problem cannot be resolved after checking the connected compo-
nents, contact the service center or your dealer for repairs.
!This unit may not operate properly due to static electricity or other
external influences. In such cases, disconnect the power cord, wait
for approximately one minute, and connect it again to restore nor-
mal operation.
Trademarks and registered trademarks
!Pioneer DJ is a trademark of PIONEER CORPORATION and is
used under license.
!rekordbox is a registered trademark of Pioneer DJ Corporation.
!Mac, macOS and Finder are trademarks of Apple Inc., registered in
the U.S. and other countries.
!Windows is a registered trademark of Microsoft Corporation in the
U.S. and other countries.
!Intel and Intel Core are registered trademarks of Intel Corporation in
the U.S. and other countries.
!ASIO is a trademark of Steinberg Media Technologies GmbH.
The names of companies and products mentioned herein are trade-
marks or registered trademarks of their respective owners.
Cautions on copyrights
rekordbox restricts playback and duplication of copyright-protected
music contents.
!When coded data, etc., for protecting the copyright is embedded in
the music contents, it may not be possible to operate the program
normally.
!When rekordbox detects that coded data, etc., for protecting the
copyright is embedded in the music contents, processing (playback,
reading, etc.) may stop.
Recordings you have made are for your personal enjoyment and
according to copyright laws may not be used without the consent of the
copyright holder.
!Music recorded from CDs, etc., is protected by the copyright laws
of individual countries and by international treaties. It is the full
responsibility of the person who has recorded the music to ensure
that it is used legally.
!When handling music downloaded from the Internet, etc., it is the
full responsibility of the person who has downloaded the music to
ensure that it is used in accordance with the contract concluded
with the download site.

En 17
Additional information
Specifications
AC adapter
Power requirements............................. AC 100 V to 240 V, 50 Hz/60 Hz
Rated current ..................................................................................0.6 A
Rated output ...................................................................... DC 12 V, 2 A
General – Main Unit
Power consumption ................................................. DC 12 V, 1 400 mA
Main unit weight.............................................................. 4.7 kg (10.4 lb)
Max. external dimensions ... 632 mm (W) × 69.7 mm (H) × 334.5 mm (D)
(24.9 in. (W) × 2.8 in. (H) × 13.2 in. (D))
Tolerable operating temperature.......+5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity...................5 % to 85 % (no condensation)
Audio Section
Sampling rate............................................................................44.1 kHz
A/D, D/A converter .........................................................................24-bit
Frequency characteristic
USB, LINE, MIC 1, MIC 2.........................................20 Hz to 20 kHz
S/N ratio (rated output, A-WEIGHTED)
USB .......................................................................................111 dB
LINE.........................................................................................94 dB
PHONO....................................................................................80 dB
AUX (0 dB)..............................................................................94 dB
AUX (12 dB)............................................................................94 dB
MIC 1 .......................................................................................77 dB
MIC 2 .......................................................................................77 dB
Total harmonic distortion (20 Hz to 20 kHzBW)
USB .....................................................................................0.003 %
LINE.....................................................................................0.005 %
Standard input level / Input impedance
LINE.......................................................................... –12 dBu/47 kW
PHONO..................................................................... –52 dBu/47 kW
AUX (0 dB)............................................................... –12 dBu/47 kW
AUX (12 dB)............................................................. –24 dBu/47 kW
MIC 1 .......................................................................... –57 dBu/3 kW
MIC 2 .......................................................................... –57 dBu/3 kW
Standard output level / Load impedance / Output impedance
MASTER 1............................................ +6 dBu/10 kW/410 Wor less
MASTER 2.............................................. +2 dBu/10 kW/1 kWor less
BOOTH ................................................. +6 dBu/10 kW/820 Wor less
PHONES................................................... +8 dBu/32 W/10 Wor less
Rated output level / Load impedance
MASTER 1.................................................................. 25 dBu/10 kW
MASTER 2.................................................................. 21 dBu/10 kW
BOOTH ....................................................................... 25 dBu/10 kW
Crosstalk
LINE.........................................................................................82 dB
Channel equalizer characteristic
HI .............................................................. –26 dB to +6 dB (20 kHz)
MID ............................................................. –26 dB to +6 dB (1 kHz)
LOW............................................................–26 dB to +6 dB (20 Hz)
Microphone equalizer characteristic
HI ............................................................ –12 dB to +12 dB (10 kHz)
LOW........................................................–12 dB to +12 dB (100 Hz)
Input / Output terminals
LINE/PHONO input terminals
RCA pin jacks.......................................................................... 2 sets
AUX input terminal
RCA pin jacks............................................................................ 1 set
MIC input terminals
XLR connector & 1/4” TRS jack................................................. 1 set
1/4” TRS jack ............................................................................ 1 set
MASTER 1 output terminal
XLR connector .......................................................................... 1 set
MASTER 2 output terminal
RCA pin jacks............................................................................ 1 set
BOOTH output terminal
1/4” TRS jack ............................................................................ 1 set
PHONES output terminal
1/4” stereo jack ......................................................................... 1 set
3.5 mm stereo mini jack............................................................. 1 set
USB terminals
B type........................................................................................ 1 set
!Be sure to use the [MASTER 1] output terminals for a balanced
output. If they are connected to an unbalanced input (such as RCA)
using an XLR to RCA converter cable (or converter adapter), etc.,
the sound quality may be lowered or noise may occur.
For connection with an unbalanced input (such as RCA), use the
[MASTER 2] output terminals.
!Be sure to use the [BOOTH] output terminals for a balanced output.
If they are connected to an unbalanced input (such as an RCA or
TS terminal) with an TRS to RCA converter cable (or converter
adapter), TS cable, etc., the sound quality may be lowered or noise
may occur.
!The specifications and design of this product are subject to change
without notice.

En
18

En 19
Additional information
UCP0516
Pioneer DJ Americas, Inc.
LIMITED WARRANTY
WARRANTY VALID ONLY IN THE U.S.A. AND CANADA
WARRANTY
Pioneer DJ Americas, Inc. (PDJA) warrants that products distributed by PDJA in the U.S.A. and Canada that fail to function properly under normal use due to a manufacturing
defect when installed and operated according to the owner’s manual enclosed with the unit will be repaired or replaced with a unit of comparable value, at the option of PDJA,
without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PDJA.
THIS LIMITEDWARRANTY APPLIESTOTHE ORIGINAL OR ANY SUBSEQUENT OWNER OFTHIS PIONEER DJ PRODUCT DURINGTHEWARRANTY PERIOD PROVIDEDTHE
PRODUCT WAS PURCHASED FROM AN AUTHORIZED PIONEER DJ DISTRIBUTOR/DEALER INTHE U.S.A. OR CANADA. YOU WILL BE REQUIREDTO PROVIDE A SALES
RECEIPT OR OTHERVALID PROOF OF PURCHASE SHOWINGTHE DATE OF ORIGINAL PURCHASE OR,IF RENTED,YOUR RENTAL CONTRACT SHOWINGTHE PLACE AND
DATE OF FIRST RENTAL. IN THE EVENT SERVICE IS REQUIRED, THE PRODUCT MUST BE DELIVERED WITHIN THE WARRANTY PERIOD, TRANSPORTATION PREPAID,
ONLY FROMWITHINTHE U.S.A. AS EXPLAINED INTHIS DOCUMENT. YOUWILL BE RESPONSIBLE FOR REMOVAL AND INSTALLATION OFTHE PRODUCT. PDJA WILL PAY
TO RETURNTHE REPAIRED OR REPLACEMENT PRODUCTTOYOUWITHINTHE U.S.A.
PRODUCT WARRANTY PERIOD Parts Labor
Audio and Video .............................................................................................................................................................................................. 1 Year 1 Year
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IF THIS PRODUCT WAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR,THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THIS PRODUCT IS SOLD STRICTLY “AS IS” AND “WITH ALL FAULTS".
PIONEER DJ SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES.
THIS WARRANTY DOES NOT APPLY IF THE PRODUCT HAS BEEN SUBJECTED TO POWER IN EXCESS OF ITS PUBLISHED POWER RATING.
THISWARRANTY DOES NOT COVERTHE CABINET OR ANY APPEARANCE ITEM, USER ATTACHED ANTENNA, ANY DAMAGETO RECORDS OR RECORDINGTAPES OR DISCS, ANY
DAMAGETO THE PRODUCT RESULTING FROM ALTERATIONS, MODIFICATIONS NOT AUTHORIZED IN WRITING BY PIONEER DJ, ACCIDENT, MISUSE OR ABUSE, DAMAGE DUETO
LIGHTNING ORTO POWER SURGES, SUBSEQUENT DAMAGE FROM LEAKING, DAMAGE FROM INOPERATIVE BATTERIES,ORTHE USE OF BATTERIES NOT CONFORMINGTOTHOSE
SPECIFIED INTHE OWNER’S MANUAL.
THIS WARRANTY DOES NOT COVERTHE COST OF PARTS OR LABOR WHICH WOULD BE OTHERWISE PROVIDED WITHOUT CHARGE UNDER THIS WARRANTY OBTAINED FROM
ANY SOURCE OTHERTHAN A PIONEER DJ AUTHORIZED SERVICE COMPANY OR OTHER DESIGNATED LOCATION. THISWARRANTY DOES NOT COVER DEFECTS OR DAMAGE CAUSED
BYTHE USE OF UNAUTHORIZED PA RTS OR LABOR OR FROM IMPROPER MAINTENANCE.
ALTERED, DEFACED, OR REMOVED SERIAL NUMBERS VOID THIS ENTIRE WARRANTY
NO OTHER WARRANTIES
PIONEER DJ LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE WARRANTY PERIOD.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND SOME STATES DO NOT ALLOW THE EXCLUSIONS OR LIMITATIONS
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
TO OBTAIN SERVICE
PDJA has appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service you
need to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit you will need to package it
carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business
hours.
On all complaints and concerns in the U.S.A. and Canada call Customer Support at 1-800-872-4159.
For hook-up and operation of your unit or to locate an
Authorized Service Company, please call or write:
CUSTOMER SUPPORT
PIONEER ELECTRONICS (USA) INC.
P. O. BOX 1720
LONG BEACH, CALIFORNIA 90801
1-800-872-4159
http://www.pioneerelectronics.com
DISPUTE RESOLUTION
Following our response to any initial request to Customer Support, should a dispute arise between you and Pioneer DJ, Pioneer DJ makes available its Complaint Resolution
Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. Yo u are required to use the Complaint Resolution Program before you exercise
any rights under, or seek any remedies, created by Title I of the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-872-4159 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer DJ product was purchased. After the
complaint has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, Pioneer DJ will investigate the dispute
and will either: (1) respond to your complaint in writing informing you what action Pioneer DJ will take, and in what time period, to resolve the dispute; or (2) respond to your
complaint in writing informing you why it will not take any action.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____________________________________________ Serial No. _________________________________________ Purchase Date ______________________
Purchased From ____________________________________________________________________________________________________________________________
_
KEEP THIS INFORMAT ION AND YOUR SALES RECEIPT IN A SAFE PLACE

PIONEER ELECTRONICS (THAILAND) CO., LTD.
17th Fl., KPN Tower, 719 Rama 9 Road, Bangkapi, Huaykwang, Bangkok 10310
TEL: [phone]
PIONEER TECHNOLOGY (MALAYSIA) SDN. BHD
16th Floor, Menara Uni. Asia 1008 Jalan Sultan Ismail 50250 Kuala Lumpur
TEL: [phone]
ӒᎣ޷ӌԥϵѨ
ѯᢋѯіҀϲ෺ୣ࿆ӏၰ ĵıĸ ဵĹዃTEL: [phone]
ӒᎣႬφȞ෬ȟԥϵѨ
෬Οᓹߞؔᢋၿ ĺıĺġဵ Ķġዃ TEL: [phone]
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec,
Mexico, D.F. 11000 TEL: [phone]
PIONEER INDIA ELECTRONICS PRIVATE LTD.
216, Second Floor, Time Tower, M.G. Road, Sector 28, Gurgaon 122001,
Haryana, India TEL: [phone]
PDJ_001_all
6F, Yo kohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yo kohama, Kanagawa 220-0012 JAPA N
〒220-0012神奈川県横浜市西区みなとみらい4丁目4番5号横浜アイマークプレイス6階
Корпорация Пайонир Диджей
6F, Йокогама i-Mark Place, 4-4-5 Минатомирай, Ниси-ку, Йокогама, Канагава 220-0012 ЯПОНИЯ
Artemis Building, Odyssey Business Park, West End Road,South Ruislip, Middlesex, HA4
6QE, U.K.TEL: [phone]
2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A. TEL: [phone]
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346 TEL: [phone]
PIONEER ELECTRONICS AUSTRALIA PTY. LT D.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: [phone]
To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA/Aux Etats-Unis or In Canada/Aux Canada
http://www.pioneerelectronics.com
S018_C1_EnFr_PSV
© 2019 Pioneer DJ Corporation.
All rights reserved.
Printed in Malaysia <DRH1525-A>