Pioneer DEH-X1950UB Use and care manual

System Firmware Update Instructions for Pioneer Receivers
(DEH-X1950UB, DEH-X2950UI, DEH-X3950BT, DEH-X4950BT, MVH-X195UI and MVH-X395BT)
This firmware update (version 8.17) applies only to the following models of Pioneer products sold in
Australia and New Zealand.
DEH-X1950UB
DEH-X2950UI
DEH-X3950BT
DEH-X4950BT
MVH-X195UI
MVH-X395BT
IMPORTANT
Please download and print these firmware update instructions before downloading and installing the
firmware update. It is important that you complete all steps correctly and in the order described below.
Note: If you have any questions, please contact Pioneer Customer Service toll free on 1800 672 102,
Monday through Friday, 9:00 AM - 5:00 PM, excluding holidays.
In order to perform this update, the following items are needed:
•Pioneer CD receiver listed above.
•A USB storage device with the following requirements.
-2 GB or larger in capacity, formatted to FAT32
-Should be blank (should not contain any files)
CAUTION
•DO NOT turn your unit off, eject the USB storage device while the firmware is being updated.
•You can only update the firmware when the vehicle is stopped and the parking brake is engaged.
Checking the firmware version
Check whether the firmware of your unit needs to be updated by checking the version number of the
firmware.
Procedure:
1. Start the vehicle engine.
2. If AV Source is On, Press and hold SRC/OFF to set the unit Source OFF.

3. Press M.C. (multi-control) to display the “Initial ”menu. then press to confirm.
4. Turn M.C. dial to select “S/W UPDATE”, then press to confirm.
5. Select the “SYSTEM INFO” to confirm the system info.
6. After the “SYSTEM INFO” screen appears, check the firmware version.
7. Verify that the firmware on your unit is not already 8.17.
Downloading the firmware update files from Pioneer's website
1. Download the firmware update files by clicking on the following link and finding your product:
https://www.pioneer.com.au/firmwaresoftware/
2. Extract the download file.

The Downloaded zip file will produce the following file when decompressed: (See the table below)
DEH-X1950UB
17ullow817.scd
DEH-X2950UI
DEH-X3950BT
DEH-X4950BT
MVH-X195UI
MVH-X395BT
Updating the firmware on your Unit
IMPORTANT
DEH-X1950UB
DEH-X2950UI
DEH-X3950BT
DEH-X4950BT
MVH-X195UI
MVH-X395BT
•DO NOT perform this firmware update if the model number of your Pioneer product is anything other
than one of the above models.
•Ensure that the update file is located within the root (top) folder of your USB storage device. There
should be no other files within the USB storage device.
•While your unit is being updated, DO NOT turn off the system’s power and DO NOT touch the unit’s
touchscreen as this may result in severe damage to your unit.
•DO NOT remove the USB storage device during the firmware update process.
•Performing the firmware update will restore all settings to their default values.
•Disconnect any external mobile devices that are currently connected to your unit.

Procedure:
1. Connect a blank (formatted) USB storage device to your computer, and then locate and copy the
“.scd” file onto the USB storage device.
2. Start the vehicle engine.
3. Connect the USB storage device to the USB input on your unit.
4. If AV Source is On, Press and hold SRC/OFF to set the unit Source OFF.
5. Press the M.C. (multi-control) to display the Initial menu.
6. Turn M.C. dial to select “S/W UPDATE“, then press to confirm.
7. Select the “SYSTEM UPDATE” item for updating the unit to the lastest software.
8. The “CHECK FILE” screen appears.
-> If it shows “ERROR” on the display, Try the following
“FILE ERROR” Confirm the software is correct, then restart Version up or change a new USB memory.
“ERR->RETRY” Do not turn off the power! Unit will retry Version up automatically.

9. After starting, there will be a progress bar while updating.
10. Wait for until the Version Up complete. (For about 5 minutes)
-> The following screen will show if the Version Up ends successfully.
11. The product will reboot after the update is finished. Do not touch anything even when the screen is
blacked out.After it has finished rebooting, the screen will return to the menu screen.
12. The firmware update is now complete. Your Pioneer CD Receiver is now ready for use.
Check if the firmware has been updated
Perform the same procedure for “Displaying the firmware version” to check if the firmware has been
updated.
Procedure:
1. If AV Source is On, Press and hold SRC/OFF to set the unit Source OFF.
2. Press M.C. (multi-control) to display the “INITIAL ”menu then press again to confirm.
3. Turn M.C. dial to select “S/W UPDATE”, then press to confirm.
4. Select the “SYSTEM INFO” to confirm the system info.
5. After the “SYSTEM INFO” screen appears, check the firmware version is 8.17.

Contact Information
Pioneer Customer Support Center
http://www.pioneer.com.au
------------------------------------------------------------
Copyright(c) 2018 Pioneer Corporation