Pioneer DEH-X2900UI User manual

CD
RDS
RECEIVER
AUTORADIO
CD
RDS
REPRODUCTOR
DE
CD
CON
RECEPTOR
RDS
DEH-X2900UI
~
Important (Serial number)
PANDORA
Gspotify
®
Made
for
~
iPod
D
iPhone
Owner's
Manual
Mode d'emploi
Manual
de
instrucciones
The serial
number
is
located on the
bottom
of
this unit.
For
your
own
security and
convenience, be sure
to
record this
number
on the enclosed warranty card.
~
Important (Numero de serie)
Le
numero de serie
se
trouve
au
bas
de cet appareil. Pour votre securite et votre commodite,
veillez
a
noter
ce
numero sur
Ia
carte de garantie fournie.
~
lmportante (Numero de serie)
El
numero de serie
se
encuentra en
Ia
parte inferior de esta unidad. Por
su
propia seguridad
y comodidad, asegurese de anotar este numero
en
Ia
tarjeta de garantfa que
se
ad
junta.
m
Ill
"0
Dl
:St
2..

ITable
of
Contents
Before
You
Start....................................................................................... 2
Getting
Started..................................•..................................................... 3
Radio.......................................................................................................... 5
CD/USB/iPod/
AUX
................................................................................... 6
App
Mode
..............•.................................................................................. 8
Pandora® ................................................................................................... 8
Spotify®..................................................................................................... 9
Using Pioneer
ARC
APP
........................................................................ 10
Settings...............................................•................................................... 10
FUNCTION settings ...................•..........................................................
11
AUDIO settings......................................................................................
11
SYSTEM
settings•.................................................................................. 12
ILLUMINATION settings....................................................................... 12
MIXTRAX settings.•............................................................................... 13
Connections/Installation..................................................................... 13
Additional
Information
........................................................................ 15
About
this
manual:
• In
the
following
instructions, a
USB
memory
or
USB
audio player
are
referred
to
as
"USB
device".
• In this manual, iPod and iPhone are referred
to
as
"iPod'~
2
En
IBeforeYou
Start
Thank you
for
purchasing
this
PIONEER
product
To
ensure proper
use,
please
read
through this manual before using this product. It
is
especially
important
that you read and observe WARNINGs and CAUTIONs in this manual.
Please
keep the
manual in a
safe
and accessible place for future reference.
This device complies
with
Part
15
of
the
FCC
Rules.
Operation
is
subject
to
the following
two
conditions:
(1)
this device may
not
cause harmful interference, and
(2)
this device must accept any interference
received, including interference
that
may cause undesired operation.
Alteration or modifications carried
out
without
appropriate authorization may invalidate
the
user's
right
to
operate the equipment.
Note
This equipment
has
been tested and found
to
comply
with
the limits for a
Class
Bdigital device,
pursuant
to
Part
15
of
the
FCC
Rules.
These limits are designed
to
provide reasonable protection
against harmful interference in a residential installation.This equipment generates,
uses
and
can
radiate radio frequency energy and,
if
not
installed and used in accordance
with
the instructions,
may cause harmful interference
to
radio communications. However, there
is
no
guarantee
that
interference will
not
occur in a particular installation.
If
this
equipment
does cause harmful
interference
to
radio ortelevision reception, which can be determined by turning the
equipment
off
and on,
the
user
is
encouraged
to
try
to
correct the interference by one
or
more
of
the
following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the
equipment
and receiver.
-Connect the
equipment
into
an
outlet
on a circuit differentfrom
that
to
which the receiver
is
connected.
-Consult the dealer or
an
experienced radio!TV technician for help.
The Safety
of
Your
Ears
is in Your Hands
Get
the
most
out
of
your
equipment
by playing
it
at a
safe
level-a
level
that
lets the sound come
through
clearly
without
annoying blaring or distortion and, most importantly,
without
affecting your
sensitive hearing. Sound
can
be deceiving.
Over time, your hearing "comfort level" adapts
to
higher volumes
of
sound,
so
what sounds "normal"
can actually
be
loud and harmful
to
your hearing. Guard against this by setting your equipment at a
safe
level
BEFORE
your hearing adapts.
ESTABLISH
A
SAFE
LEVEL:
•
Set
your volume control at a
low
setting.
•Slowly increase the sound until you
can
hear
it
comfortably and clearly,
without
distortion.
•Once you have established a comfortable sound level, set the dial and leave
it
there.
BE
SURE
TO
OBSERVE
THE
FOLLOWING GUIDELINES:
•Do
not
turn
up
the volume
so
high
that
you can't hear what's around you.
•
Use
caution ortemporarily discontinue
use
in potentially hazardous situations.
•Do
not
use headphones while operating a motorized vehicle; the
use
of
headphones may create a
traffic hazard and
is
illegal in many
areas.

A wARNING
•
Do
not
attempt
to
install
or
service
this
product
by
yourself.
Installation
or
servicing
of
this
product
by
persons
without
training
and
experience
in
electronic
equipment
and
automotive
accessories
may
be
dangerous
and
could
expose
you
to
the
risk
of
electric
shock,
injury
or
other
hazards.
•
Do
not
attempt
to
operate the
unit
while driving. Make sure
to
pull
off
the road and park your vehicle
in a
safe
location before
attempting
to
use
the controls on
the
device.
CAUTION:
USE
OF
CONTROL
OR
ADJUSTMENT
OR
PERFORMANCE
OF
PROCEDURES
OTHER
THAN THOSE
SPECIFIED HEREIN MAY
RESULT
IN HAZARDOUS RADIATION EXPOSURE.
CAUTION:
THE
USE
OF
OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE
EYE
HAZARD.
A
CAUTION
• Do
not
allow this
unit
to
come into contact
with
moisture
and/or
liquids. Electrical shock could result.
Also, damage
to
this unit, smoke, and overheating could result from contact
with
liquids.
•Always keep
the
volume
low
enough
to
hear outside sounds.
•This
product
is
evaluated in moderate and tropical climate
condition
under the Audio, video and
similar electronic apparatus- Safety requirements,
IEC
60065.
CAUTION
This
product
is
a
class
1 laser
product
classified under the Safety
of
laser products,
IEC
60825-1 :2007.
I
CLASS
1
LASER
PRODUCT
I
After-sales service
for
Pioneer products
Please
contact
the
dealer,
distributor
from where you purchased this
unit
or
the authorized
PIONEER
Service Station for after-sales service
or
any other information. In
case
the necessary information
is
not
available, please contact the companies listed below:
Please
do
not
ship your
unit
to
the companies at the addresses listed below for repair
without
contacting
them
in advance.
U.S.A.
and
CANADA
Pioneer Electronics
(USA)
Inc.
CUSTOMER
SUPPORT
DIVISION
P.O.
Box 1760
Long Beach,
CA
90801-1760
800-421-1404
For
warranty information please
see
the Limited Warranty sheet included
with
this unit.
IGetting
Started
DEH-X2900UI
M.C.
(multi-control)
dial Disc loading slot
USB
port
~(eject)
SRC
(source)/OFF Display
window
DISP
(display)
BAND/!:>
Detach
button
AUX
input
jack
(3.5
mm
stereo jack)
Remote Control
FUNCTION
SRC
(source)
VOLUME+/-
MUTE
AUDIO
DISP
(display)
En
3

Frequently used operations
Purp()se Operatiot'l
I
•····
...
Head
Unit
.....
Q'tmot'
t9ntrQI
.·.········
···
•·•·
·
·•·i
••••
•
•••••••••••
·
·········
(J
........
.
Turn on the power*
Press
SRC/OFF
to
turn
on
Press
SRC
to
turn
on
the
the power. power.
Press
and hold
SRC/OFF
to
Press
and hold
SRC
to
turn
turn
off
the power.
off
the power.
Adjust the volume Turn the
M.C.
dial.
Press
VOLUME+
or-.
Press
MUTE
to
mute
the
unit.
Press
MUTE
again or
press
VOLUME
+or-
to
unmute.
Select a source
Press
SRC/OFF
repeatedly.
Press
SRC
repeatedly.
Change the display
Press
DISP
repeatedly.
Press
DISP
repeatedly.
information
Return
to
the previous
Press
BAND/!:>
.
Press
..._/~
to
select
the
display/list next/previous folder.
Return
to
the normal display
Press
and hold
BAND/!:>
.
-
from the menu
*
When this unit's
blue/white
lead
is
connected
to
the vehicle'sauto-antenna relay control terminal,
the vehicle's antenna extends when this unit's source
is
turned on.
To
retract the antenna, turn
the
source off.
Display indication
LOC
Appears when the local seek
tuning
function
is
set (page
11
).
----=ld4!1
Appears when
the
sound retriever function
is
set (page
11
).
Appears when random/shuffle play
is
set.
Appears when repeat play
is
set.
Appears when the iPod control function
is
set (page
7).
4En
••
<
Dt~t~c
·
b
·
i
119
··..
tlj
·
~
·
.·•·
f~p
·
~~
······
PiJR
·
~
·
I
Detach
the
front
panel
to
prevent
theft.
Remove any cables and devices
attached
to
the
front
panel and
turn
off
the
unit
before
detaching
it.
Detach Attach
c!r
Important
• Avoid subjecting the front panel
to
excessive shock.
• Keep the
front
panel
out
of
direct sunlight and
high
temperatures.
• Always store the detached
front
panel in a protective
case
or bag.
Remove
the
insulation sheet before use.
A
wARNING
How
to replace
the
battery
Insert the
CR2025
(3
V)
battery with the plus(+) and
minus(-)
poles orientated properly.
• Do not ingest the battery, Chemical Burn Hazard
(The remote control supplied with) This
product
contains a
coin/button
cell battery.
If
the
coin/
button
cell battery
is
swallowed,
it
can cause severe internal burns in just 2 hours and can lead
to
death.
Keep new and used batteries away from children.
If
the battery
compartment
does
not
close securely, stop using the
product
and keep
it
away from
children.

Ifyou think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
•
Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.
A CAUTION
• There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the
battery, replace it with the same type.
•
Do not handle or store the battery with metallic tools or objects.
• If
the battery leaks, remove the battery and wipe the remote control completely clean. Then install a
new battery.
• When disposing
of used batteries, please comply with governmental regulations or environmental
public institutions' rules
that apply in your country/area.
• "Perchlorate Material- special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable to California, U.S.A.)"
':!)= Important
• Do not store the remote control in high temperatures or direct sunlight.
•
Do not let the remote control fall onto the floor, where it may become jammed under the brake or
accelerator pedal.
When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the
display.
1 Press the M.C. dial.
The setup menu disappears after 30 seconds of no operation.lf you prefer not to set
at this time, turn the M.C. dial to select [NO], then press to confirm.
2 Turn the M.C. dial to adjust the hour, then press to confirm.
The indicator moves to the minute setting automatically.
3 Turn the M.C. dial to adjust the minute, then press to confirm.
[QUIT] appears.
4 Turn the M.C. dial to select [YES], then press to confirm.
NOTES
• You can cancel the menu setting by pressing SRC/OFF.
• This setting can be made at any time. See page 12 for more details.
1 Press the M.C. dial to display the main menu.
2 Turn the M.C. dial to select [SYSTEM], then press to confirm.
3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.
4 Turn the M.C. dial to select [YES], then press to confirm.
INITIAlsettings
1 Press and hold SRC/OFF until the unit turns off.
2 Press the M.C. dial to display the main menu.
3 Turn the M.C. dial to select [INITIAL], then press to confirm.
4 Turn the M.C. dial to select an option, then press to confirm.
SP-P/0 MODE
[REAR/SUB.W]
[SUB.W/SUB.W]
[REAR/REAR]
S/W UPDATE
[SYSTEM INFO]
Select when there is afull-range speaker connected to the rear
speaker
output leads and there is a subwoofer connected to the
RCA output.
Select when there
is a passive subwoofer connected directly to
the rear speaker output leads and there is a subwoofer
connected
to the RCA output.
Select when there are full-range speakers connected to the rear
speaker
output leads and RCA output. If there is afull-range
speaker connected
to the rear speaker output leads, and the
RCA output is not used, you may select either [REAR/SUB.W] or
[REAR/REAR].
Select to confirm the latest system information on the unit.
[SYSTEM UPDATE] Select to update the unit to the latest software and initialize the
unit settings. For details on the latest software and updating,
visit our website.
SYSTEM RESET
[YES], [NO]
IRadio
Select [YES] to initialize the unit settings. The unit will be
restarted automatically.
(Some
of the settings may be retained even after resetting the
unit.)
The
tuner frequencies on this unit are allocated for use in North America. Use in other
areas may result in poor reception.
En 5
m
:::s
~
iii'
:::J"

li~ei
•
¥i
.
n
•
a
····•••
p
•
r•~•t
••••••
&tat
•
i
·
on
•·
s
··
1
Press
SRC/OFF
to
select [RADIO].
2
Press
BAND/!:>
to select
the
band from [FM1], [FM2], [FM3] or [AM].
3
Press
a
number
button
(1/
A to
6/~).
TIP
The
~/
.........
buttons
can be also used
to
select a preset station
when
[SEEK]
is
set
to
[PCH]
in
the
FUNCTION settings (page
11
).
The six strongest stations are stored on
the
number
buttons (1/
A
to
6/~).
1 After selecting the band, press
the
M.C. dial
to
display
the
main menu.
2
Turn
the
M.C. dial to select [FUNCTION],
then
press to confirm.
3 Turn
the
M.C. dial to select [BSM], then press to confirm.
To
seek a station manually
1 After selecting
the
band, press
~/...,...
to
select a station.
Press
and hold
~/...,...
then release
to
seek
an
available station. Scanning stops
when the
unit
receives a station.
To
cancel seek tuning, press
~/...,....
NOTE
[SEEK]
needs
to
be set
to
[MAN] in the FUNCTION settings (page
11
).
To
store stations manually
1 While receiving
the
station you
want
to
store, press and hold one
of
the
number
buttons
(1/
A
to
6/~)
until
it
stops flashing.
ICD/USB/iPod/AUX
Disconnect headphones from
the
device before connecting
it
to
the
unit.
CD
1 Insert a disc into
the
disc loading slot
with
the
label side up.
To
eject a disc, stop playbackfirst then press
~.
USB
devices (including Android™)/iPod
1 Open
the
USB
port
cover.
2 Plug in
the
USB
device/iPod using an appropriate cable.
NOTE
To
automatically switch
to
[USB]
source
when
a
USB
device/iPod
is
connected
to
the unit, set
[USB
AUTO]
to
[ON] in the
SYSTEM
settings (page
12).
A
cAUTION
Use
an
optional
Pioneer
USB
cable
(CD-USOE)
to
connect
the
USB
device
as
any device connected
directly
to
the
unit
will
protrude
out
from
the
unit, which could be dangerous.
Before removing
the
device, stop playback.
AOA connections
For details on
AOA
connection,
see
page 10.
MTP connection
A device installed
with
Android
OS
4.0
or
later can be connected
to
the
unit
via
MTP,
using
the
cable
supplied
with
the
device. However,
depending
on
the
connected device and
the
numbers
of
the
files in
the device,
audio
files/songs
may
not
be able
to
be played back via
MTP.
Note
that
MTP
connection
is
not
compatible
with
WAV
file formats, and
cannot
be used
with
the
MIXTRAX function.
NOTE
Ifyou use an
MTP
connection, [ANDROID
WIRED]
needs
to
be set
to
[MEMORY] in
the
SYSTEM
settings
(page 12).
AUX
1 Insert
the
stereo mini plug into
the
AUX
input
jack.
2
Press
SRC/OFF
to
select [AUX]
as
the
source.
NOTE
If [AUX]
is
set
to
[OFF]
in
the
SYSTEM
settings, [AUX]
cannot
be selected
as
a source (page 12).
You
can
make various adjustments in
the
FUNCTION
settings (page
11
).
Note
that
the
following
operations
do
not
work
for
an
AUX
device.
To
operate
an
AUX
device, use
the
device itself.

Search
for afile from a list
Press
and hold
Press
~
to
display the list.
2 Turn the
M.C.
dial
to
select the desired
file (folder) name or category, then
press
to
confirm.
3 Turn the
M.C.
dial
to
select the desired
file, then
press
to
confirm.
Playback starts.
View a list
of
the files
in
the selected folder/
Press
the
M.C.
dial when afoldericategory
category*l
is
selected.
Play
a song in the selected folder/
Press
and hold the
M.C.
dial when afolder/
category*l category
is
selected.
Alphabetical
search
(iPod only)
Press
~
to
display the list.
Sound retriever*l
2 Turn the
M.C.
dial
to
select the desired
category list, then
press
~
to enter the
alphabetical search mode.
(Turning the
M.C.
dial twice also enters
the alphabetical
search
mode.)
3 Turn the
M.C.
dial
to
select a letter, then
press
to
display the alphabetical list.
To
cancel alphabetical search,
press
BAND/
!:>.
Switch between compressed audio and
CD-
Press
BAND/!:>.
DA
(CD
only)
Change drives in
USB
device
Press
BAND/!:>.
(Devices
that
supportthe
USB
mass
storage
device
class
protocol only)
*1 Compressed audio files only
*2 When you
use
the
fast forward or reverse function while playing a
VBR
file, the playback
time
may
be
not
correct.
Useful
functions for
iPod
Link play mode
You
can
access
songs based on
the
artist, album,
or
genre currently playing.
1
While listening to a song, press and hold
~
to
enter
the
link play mode.
2 Turn
the
M.C. dial to select
the
mode
([ARTIST], [ALBUM], [GENRE]), then press to
confirm.
The selected song/album will be played after
the
currently playing song.
NOTE
The selected song/album may be canceled
if
you
use
functions other than those from
the
link play
mode
(e.g. fast forward and reverse).
i
Pod control
You
can control
the
unit
via a connected iPod.
The
following
iPod models
are
not
compatible
with
this function.
-iPod nano 1st generation, iPod
with
video
1
Press
BAND/!:>
during playback,
then
select
the
control mode.
[CONTROL iPod]:
The unit's iPod
function
can
be operated from
the
connected iPod.
[CONTROL AUDIO]:
The unit's iPod function can
only
be operated by
the
buttons on
the
unit
or
supplied remote control.
In
this mode,
the
connected iPod cannot be
turned
on or
off
.
NOTES
• Switching
the
control
mode
to
[CONTROL
iPod) pauses song playback.
Use
the connected iPod
to
resume playback.
• The
following
operations are still accessible from the unit, even
if
the
control
mode
is
set to
[CONTROL
iPod).
-Pause, fast forward/reverse, song/chapter selection
• The volume can
only
be adjusted from the unit.
The MIXTRAX
function
creates a non-stop mix
of
your
music library, accompanied
by
illumination
effects.
For
details on MIXTRAX settings,
see
page 13.
NOTES
• This
function
is
not
compatible
with
an Android device connected via
MTP.
• When
USB
is
selected
as
asource and
the
MIXTRAX
function
is
in
use,
the sound retriever function
is
disabled.
En
7
m
:::s
"9.
iii'
:::r

• Depending on the file/song, sound effects may
not
be available.
• Turn the
MIXTRAX
function
off
if
the
illumination effects
it
produces interfere
with
driving.
1
Press
MIX
to
turn MIXTRAX on/off.
IAppMode
You
can
enjoy
listening
to
an
application on an iPhone via
the
unit. In some
cases,
you
can control an application by using
the
unit.
For details on
compatible
devices, visit
our
website.
c
!}
~
Important
Use
of
third party apps may involve or require the provision
of
personally identifiable information,
whetherthrough the creation
of
auser account or otherwise, and for certain applications, the provision
of
geolocation data.
ALL
THIRD
PARTY
APPS
ARE
THE
SOLE
RESPONSIBILITY
OF
THE
PROVIDERS,
INCLUDING
WITHOUT
LIMITATION
COLLECTION
AND
SECURITY
OF
USER
DATA
AND
PRIVACY
PRACTICES
.
BY
ACCESSING
THIRD
PARTY
APPS,
YOU
AGREE
TO
REVIEW
THE
TERMS
OF
SERVICE
AND
PRIVACY
POLICIES
OF
THE
PROVIDERS.
IF
YOU
DO
NOT
AGREE
WITH
THE
TERMS
OR
POLICIES
OF
ANY
PROVIDER
OR
DO
NOT
CONSENT
TO
THE
USE
OF
GEOLOCATION
DATA
WHERE
APPLICABLE,
DO
NOT
USE
THAT
THIRD
PARTY
APP.
For iPhone users
This function
is
compatible with iPhones and iPod touches installed
with
iOS
5.0
or later.
NOTE
PIONEER
IS
NOT
LIABLE
FOR
ANY
THIRD
PARTY
APPS
OR
CONTENT,
INCLUDING
WITHOUT
LIMITATION
THEIR
ACCURACY
OR
COMPLETENESS.
THE
CONTENT
AND
FUNCTIONALITY
OF
SUCH
APPS
ARE
THE
SOLE
RESPONSIBILITY
OF
THE
APP
PROVIDER.
1 Connect this unit with
the
mobile device.
• iPhone via
USB
(page
6)
2
Press
SRC/OFF
to
select [APP].
3 Operate the mobile device
to
start
up
the application.
Basic operations
You
can make various adjustments in
the
FUNCTION settings (page
11
).
Purpose
Fast
forward or reverse
Press
and hold
~
or
~.
Pause/resume playback
Press
BAND/!:>.
I
Pandora®
Pandora
internet
radio
is
a music service
not
affiliated
with
Pioneer. More
information
is
available at
http://www.pandora.com.
The Pandora
mobile
application
is
available
for
iPhone. Please visit
www.pandora.com/
everywhere/mobile
for
the
latest
compatibility
information.
Update
the
firmware
of
the
Pandora application
to
the
latest version before use.
1 Connect this unit with
the
mobile device.
• iPhone via
USB
(page
6)
2
Press
SRC/OFF
to
select [PANDORA].
3 Launch the Pandora application on the mobile device and start playback.
Basic operations
You
can make various adjustments in
the
FUNCTION settings (page 1
1
).
Skip atrack
Switch between Shuffle and the
station
Change the sort order
Play
Delete a station
Press~.
Press
0..
(list), then turn the
M.C.
dial
to
select the
Shuffle or the desired station.
Press
0..
(list), then select one
of
the following.
[ABC]:
Sort the items in the list alphabetically.
[DATE]: Sort the items in the list in order
of
the
dates on which the items were created.
When Shuffle or the station
is
selected, press the
M.C.
dial.
When the station
is
selected, press and hold the
M.C.
dial.
[DELETE
YES]
appears.
2
Press
the
M.C.
dial.
To
cancel, press
BAND/!:>
in step
1.

Thumbs Up
Thu sDown
Create a new station based on the
track currently being played
Create a new station based on the
artist currently being played
Store the track information currently
being played in your Pandora
account.
Press
and hold
5/~.
Press
and hold
6/~.
Press
and hold 3/S.RTRV.
[BOOKMARK]
appears.
2
Press
the M.C. dial.
* This function
is
disabled when the
MIXTRAX
function
is
on.
NOTE
Some functions
of
Pandora may not
be
operated from the unit.
I
Spotify®
(DEH-X2900UI
is
only
compatible
with
Spotify installed on iPhone.)
Spotify
is
a music streaming
distribution
service
not
affiliated
with
Pioneer. More
information
is
available at
http://www.spotify.com.
The Spotify application
is
available for
compatible
smartphones, please visit
https://
support.spotify.com/
for
the
latest
compatibility
information.
To
enjoy
Spotify
as
you drive, first
download
the
Spotify
app
to
your
iPhone.
You
can
download
it
on
the
iTunes
App
Store. Choose afree account or a paid Premium account,
either
in
the
app
or
at spotify.com. A Premium account gives you more features, like
offline
listening.
c!>=
Important
• This product incorporates Spotify software which
is
subject
to
3rd party licenses found here:
www.spotify.com/connect/third-party-licenses.
•
For
information on the countries and regions where Spotify can be used, take a look at https://
www.spotify.com/us/select-your-country/.
Update
the
firmware
of
the
Spotify application
to
the
latest version before
use.
1 Connect this unit with
the
mobile device.
• iPhone via
USB
(page
6)
2
Press
SRC/OFF to select [SPOTIFY].
3
Launch
the
Spotify application on
the
mobile device and start playback.
Basic operations
You
can make various adjustments in
the
FUNCTION settings (page 1
1
).
NOTE
The available operations may vary according
to
the type
of
contents (track/album/artist/playlist/radio)
you want to play.
..
...
..
.
...
...
..
·
..
..
;
..
>.
. . .
••
{{•
/
. . .
/
~
/
..<+
·
.......
•••••
••
•••••
•
••••
••
•••
•
••••••••••
••
•••••••••••••
.
...
········
.
...
·
...
i>
..
.
..
><f
•·
•
•·•·•
Skip atrack
Press~
or~
.
Search
for atrack from a list
1
Press
~
(list)
to
display the list.
2 Turn the M.C. dial
to
select the desired
category, then press
to
confirm.
3 Turn the M.C. dial
to
select the desired
file, then
press
to
confirm.
Playback starts.
Pause/resume playback
Press
4/PAUSE.
Thumbs
Up
(Only for radio)
Press
1/
A.
Thumbs Down (Only for radio)
Press
2/V.
Random play (Only for track/album/artist/
Press
5/~.
playlist)
Repeat play (Only for track/album/artist/
Press
6/~.
playlist)
Start a radio channel based on the song
1
Press
and hold
~
(list)
to
start a radio.
currently being played. 2
Press
the M.C. dial.
• This function may
not
be
available
depending on the selected song.
Store the information about the song
1
Press
and hold 3/S.Rtrv.
currently being played.
[SAVE]![UNSAVE]
appears.
Remove the song information stored. 2
Press
the M.C. dial.
NOTE
Some functions
of
Spotify may not be operated from the unit.
En
9

IUsing Pioneer ARC APP
You
can operate
the
unit
from
Pioneer
ARC
APP
installed on an iPhone/Android device.
In some
cases,
you can control aspects
of
the
application, such
as
source selection,
pause, etc.,
by
using
the
unit.
For details on
what
operations are available on
the
application,
see
the
application's
help
section.
A wARNING
Do
not
attempt
to
operate the application while driving. Make sure to pull
off
the
road and park your
vehicle in a
safe
location before
attempting
to
use
the
controls on the application.
For
iPhone
users
This
function
is
compatible
with
iPhones (iPhone 5 or later) and iPod touches installed
with
iOS
8.0
or
later.
You
can
download
Pioneer
ARC
APP
on iTunes
App
Store.
For
Android
device
users
This
function
is
compatible
with
devices
that
have Android
OS
4.1
or
later installed and
also
support
AOA (Android Open Accessory) 2.0.
You
can
download
Pioneer
ARC
APP
on
Google
Play™.
NOTE
Some Android devices connected via
AOA
2.0
may
not
work
properly
or
emit
sounds due
to
their
own
software design, regardless
of
the
OS
version.
1
Connect this
unit
with
the
mobile
device.
• iPhone/Android device via
USB
(page
6)
Proceed
to
step 6
if
you select
the
USB
connection
for iPhone.
2
Press
the
M.C. dial
to
display
the
main
menu.
3
Turn
the
M.C. dial
to
select [SYSTEM],
then
press
to
confirm.
4
Turn
the
M.C. dial
to
select [ANDROID WIRED],
then
press
to
confirm.
S
Turn
the
M.C. dial
to
select [APP CONTROL] for an Android device connected via
USB.
10
En
If
[ON]
is
selected in
[P.APP
AUTO
ON] (page 12), Pioneer
ARC
APP
on
the
Android
device starts automatically, and all
the
steps are finished.
NOTE
IfPioneer
ARC
APP
has
not
been installed on your Android device yet, a message
that
promptsyou
to install the application will appear on your Android device. Select
[OFF]
in
[P.APP
AUTO
ON]
to
clear the message (page 12).
6
Press
SRC/OFF
to
select
any
source.
7 Launch Pioneer
ARC
APP on
the
mobile
device.
NOTE
You
can also launch the application by pressing and holding
the
M.C.
dial for iPhone.
1
Press
SRC/OFF
to
select [ANDROID].
Basic
operations
Sound retriever
I
Settings
Press
3/S.Rtrv.
[1
]:
Effective for low compression rates
[2]: Effective for high compression rates
You
can adjust various settings in
the
main menu.
1
Press
the
M.C. dial
to
display
the
main
menu.
2 Turn
the
M.C. dial
to
select
one
of
the
categories below,
then
press
to
confirm.
• FUNCTION settings (page 1
1)
• AUDIO settings (page 1
1)
•
SYSTEM
settings (page 1
2)
• ILLUMINATION settings (page 1
2)
• MIXTRAX settings (page 1
3)
3 Turn
the
M.C. dial
to
select
the
options,
then
press
to
confirm.

The menu items vary according to the source.
LOCAL I filii I
Store the six strongest stations on the number
buttons (1 I A to 61¢) automatically.
FM: [OFF], [LV1], [LV2], [LV3], [LV4] Restrict the tuning station according to the
AM: [OFF], [LV1], [LV2] signal strength.
S.RTRV
[1] (effective for low compression
rates),
[2] (effective
for high
compression rates),
[OFF]
AUDIO BOOK
[FASTER], [NORMAL], [SLOWER]
BOOKMARK ''~~~~~~
NEW STATION ~~~-~~
[FROM TRACK], [FROM ARTIST]
Assign ~ or ~ buttons to seek the stations
one
by one (manual tuning) or select a station
from the preset channels.
Store
the information about the song currently
being played
to your music list on Spotify.
Remove
the song information stored in [SAVE].
Enhance compressed audio and restore rich
sound.
Not available when:
•
USB is selected as a source and the MIXTRAX
function is set to on.
• CO-DA/CD-TEXT
is played back.
Change
the playback speed. (Not available when
[CONTROL iPod] is selected in the control mode.)
Store
the track information currently being
played in
your Pandora account.
Create a
new station based on the track or artist
currently
being played.
FADER*1
BALANCE
EQSETTING
[SUPER BASS], [POWERFUL],
[NATURAL], [VOCAL], [CUSTOM 1 ],
[CUSTOM2], [FLAT]
Select an equalizer band and
level
for further customizing.
Equalizer band: [80HZ], [250HZ],
[800HZ], [2.SKHZ], [8KHZ]
Equalizer level: [+6] to [-6]
LOUDNESS
[OFF], [LOW], [MID], [HI]
SUB.W*2
[NOR], [REV], [OFF]
SUB.W CTRL *2*3
Cut-offfrequency: [50HZ],
[63HZ], [80HZ],
[1OOHZ], [125HZ],
[160HZ], [200HZ]
Output level: [-24] to [+6]
Slope level: [-12], [-24]
BASS BOOST
[0] to [+6]
Pause or resume playback.
Adjust
the front and rear speaker balance.
Adjust
the left and right speaker balance.
Select
or customize the equalizer curve.
[CUSTOM 1] can be set separatelyfor each source.
However, each
ofthe below combinations are set
to the same setting automatically.
•
USB, iPod, PANDORA (iPhone), ANDROID,
SPOTIFY, and APP (iPhone)
[CUSTOM2]
is a shared setting used for all
sources.
Compensate
for clear sound at low volume.
Select
the subwoofer phase.
Only frequencies
lower than those in the
selected range are output from the subwoofer.
Select
the bass boost level.
m
::1
'2.
iii"
:::r
En 11

HPF SETTING
Cut-offfrequency: [OFF], [50HZ], Onlyfrequencies higher than the high-pass filter
[63HZ], [80HZ],
[1OOHZ], [125HZ], (HPF) cutoff are output from the speakers.
[160HZ], [200HZ]
Slope level: [-12], [-24]
SLA
[+4] to [-4]
Adjust the volume level for each source except
FM.
Each of the below combinations are set to the
same setting automatically.
•
USB, iPod, PANDORA (iPhone), ANDROID,
SPOTIFY, and APP (iPhone)
*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/0 MODE] in the INITIAL settings (page 5).
*2 Not available when [REAR/REAR] is selected in [SP-P/0 MODE] in the INITIAL settings (page 5).
*3
Not available when [OFF] is selected in [SUB.W].
You can also access to these menus when the unit is turned off.
CLOCK SET
12H/24H
[12H], [24H]
AUX
[ON], [OFF]
SPOTIFY
[ON], [OFF]
ANDROID WIRED
[MEMORY], [APP CONTROL]
P.APP AUTO ON
[ON], [OFF]
12 En
Set the clock (page 5).
Select the time notation.
Set
to [ON] when using an auxiliary device
connected
to the unit.
Set
to [ON] when using the Spotify function.
Select the appropriateconnection method for an
Android device.
Select [ON]
to automatically launch Pioneer ARC
APP when an Android device is connected to the
unit via AOA. (Not available when [MEMORY] is
selected in [ANDROID WIRED].)
USB AUTO
[ON], [OFF]
COLOR
[KEY COLOR], [DISP COLOR],
[BOTH COLOR]
DIM SETTING
[SYNC ILLUMI], [SYNC CLOCK],
[MANUAL]
BRIGHTNESS
[KEY], [DISP]
Select [ON] to automatically switch to [USB]
source when a USB device/iPod is connected to
the unit.
Select
[OFF] when a USB device/iPod is being
connected
to the unit just for charging.
Select color for
the keys/display of the unit from
12 preset colors, [SCAN] or [CUSTOM]*.
• [SCAN]: Cycle
through a variety of colors
automatically.
• [CUSTOM]*:
1 Press and hold the M.C. dial until the color
setting display appears.
2 Set the primary color (R (red}/G (green}/B
(blue)) and brightness level ([0]
to [60]).
You cannot select a level below 10 for all three
of R(red), G (green), B(blue) at the same time.
You can also customize the preset colors. Select
one
of the preset colors, then press and hold the
M.C. dial until the color setting display appears.
* The CUSTOM setting is only available for [KEY
COLOR] and [DISP COLOR].
Change the display brightness.
Select
the brightness for the keys/display of the
unit from [1] to [1 0].
The available setting ranges differ
depending on
[DIM
SETTING].

ILLUMI
FX
[ON],
[OFF]
SHORT
PLAYBCK
[1.0 MIN], [1.5 MIN], [2.0 MIN],
[2.5 MIN], [3.0 MIN],
[OFF]
FLASH
AREA
[KEY
/DISPLAY],
[KEY],
[OFF]
FLASH
PATTERN
[SOUND
LEVEL
1]
to
[SOUND
LEVEL
6]
[LOW
PASS
1]
to
[LOW
PASS
6]
[RANDOM1]
[RANDOM2]
[RANDOM3]
DISPLAY
FX
[ON],
[OFF]
CUTIN
FX
[ON],
[OFF]
The illumination effect can be
seen
when a
CD
is
inserted/ejected.
The illumination effect will activate when the
ACC
power
is
turned
on/off
regardless
of
this
setting.
Select the length
of
the playback time.
Select the area for the illumination effect.
When
[OFF]
is
selected, the color set underthe
ILLUMINATION settings (page
12)
is
used
as
the
display color.
Change the illumination effect according
to
the sound and
bass
level.
The flash pattern changes according
to
the
sound level.
The flash pattern changes according
to
the
bass
level.
The flash pattern changes randomlyaccording
to
the sound level mode and
low
pass
mode.
The flash pattern changes randomly according
to
the sound level mode.
The flash pattern changes randomlyaccording
to
the
low
pass
mode.
Set
the
MIXTRAX
special effects on/off.
Turn the
MIXTRAX
sound effects
on/off
while
manually changing the tracks.
IConnections/Installation
A
wARNING
• When speaker
output
is
used by 4
channels,
use
speakers over
50
W
(maximum.
input
power) and between 4
0
to
8 0
(impedance value). Do
not
use
1
0
to
3 0 speakers for this unit.
• When rear speaker
output
is
used by 2
0
of
subwoofer,
use
speakers over
70
W
(maximum
input
power).
*Please refer
to
connections for a
connection method.
• The black cable
is
ground. When
installing this
unit
or power
amp
(sold
separately), make sure
to
connect the
ground wire first. Ensure that
the
ground
wire
is
properly connected
to
metal parts
of
the
car's
body. The ground wire
of
the
power amp and the one
of
this
unit
or
any other device must be connected
to
the car separately
with
different screws.
If
the
screw for the ground wire loosens or
falls out,
it
could result in fire, generation
of
smoke or malfunction.
Ground wire
POWER
AMP
~,,~
,
il
·
L
·j'~
t¥f
-1-
(!)
(!)
\-
Other devices MetaIparts
of
(Another electronic
car's
body
device
in
the
car)
*1
Not supplied for this
unit
c!>=
Important
• When installing this
unit
in avehicle
without
an
ACC
(accessory) position on
the ignition switch, failure to connect the
red cable
to
the terminal
that
detects
operation
of
the ignition key may result
in battery drain.
ACC
position
No
ACC
position
•
Use
this
unit
with
a 12-volt battery and
negative grounding only. Failure
to
do
so
may result in afire or malfunction.
•
To
prevent a short-circuit, overheating or
malfunction, be sure
to
follow the
directions below.
-Disconnect
the
negative terminal
of
the
battery before installation.
-Secure the
wiring
with
cable clamps or
adhesive tape. Wrap adhesive tape
around wiring
that
comes into contact
with
metal parts
to
protect the wiring.
-Placeall cables away from moving parts,
such
as
the shift lever and seat rails.
-Place all cables away from
hot
places,
such
as
near
the
heater outlet.
-Do
not
connect the yellow cable
to
the
battery by passing
it
through the hole
to
the engine compartment.
-Cover
any disconnected cable
connectors
with
insulating tape.
-Do
not
shorten any cables.
-Never
cut the insulation
of
the power
cable
of
this
unit
in order
to
share the
power
with
other devices. The current
capacity
of
the cable
is
limited.
-Use
afuse
of
the rating prescribed.
-Never
wire the negative speaker cable
directly
to
ground.
-Never
band together negative cables
of
multiple
speakers.
• When this unit
is
on, control signals are
sent
through
the blue/white cable.
Connect this cable
to
the system remote
En
13

control of an external power amp or the
vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
• Never
connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so
may result in battery drain or a
malfunction.
• The graphical symbol
=== placed on
the product means direct current.
This unit
CD Power cord input
(])Rear output or subwoofer output
®Antenna input
W Fuse (10 A)
®Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
Power cord
Perform these connections when not
connecting a rear speaker lead to a
subwoofer.
1 4En
II
(]) m
®
f®-~~-®·~- ----®~---
~~--~~~------·-~:~~~~2~---
f®""f-:r~~~.:.::@·-- ----@~-----~
:~--~-~--------~-~----1
1------@
1------@
t------@
1------@
a....-----@
Perform these connections when using a
subwoofer
without the optional amplifier.
t-----@
1-----@
1-----@
1-----@
L....----@
c!>= Important
@)
[
@!@@rJ(f)
® @
@ @ 8
In
the case of@) above, two 4 0
subwoofers wired in parallel
will represent
a 2 0 load.
CD To power cord input
(])Left
G) Right
G) Front speaker
®
Rear speaker
®White
(j) White/black
®Gray
®Gray/black
@Green
@ Green/black
@Violet
@Violet/black
@Black (chassis ground)
Connect to a clean, paint-free metal
location.
@Yellow
Connect to the constant 12 V supply
terminal.
@Red
Connect to terminal controlled by the
ignition switch (12 V DC).
@Blue/white
Connect to the system control terminal
of the power amp orauto-antenna relay
control terminal (max. 300
mA 12 V DC).
@ Subwoofer (4 0)
@)When using a subwoofer of 2 0, be sure
to connect the subwoofer to the violet
and
violet/black leads of this unit. Do
not connect anything to the green and
green/black leads.
®Not used.
@ Subwoofer
(4 0) x 2
@Orange/white
Connect to a car's illumination signal.
NOTE
Change the initial menu of this unit. Refer
to [SP-P/0 MODE] (page 5). The subwoofer
output of this unit is monaural.
Power amp (sold separately)
Perform these connections when using the
optional amplifier.
CD,,,,,,,,,,,,,,,,,., ... , .. ,,. ®
~___.
G)
®
8 8
CD System remote control
Connect
to blue/white cable.
(])Power
amp (sold separately)
®Connect with RCA cables (sold
separately)
G) To rear output or subwoofer output
®Rear speaker or subwoofer
c!>= Important
• Checkall connections and systems before
final installation.
• Do
not use unauthorized parts as this
may cause malfunctions.
• Consult
your dealer if installation requires
drilling of holes or other modifications to
the vehicle.
• Do
not install this unit where:
-it may interfere with operation of the
vehicle.
-it may cause injury to a passenger as a
result
of a sudden stop.
• The semiconductorlaser
will bedamaged
if it overheats. Install this unit away from
hot places such as near the heater outlet.
•
Optimum performance is
obtained when the unit is
installed at an angle of less
than 60°.
• When installing,
to ensure proper heat
dispersal
when using this unit, make sure
you leave
ample space behind the rear
panel and
wrap any loose cables so they
are not blocking the vents.
Leave ample
space
DIN mount installation
1 Insert
the supplied mounting sleeve
into
the dashboard.
2 Secure the mounting sleeve by using a
screwdriver
to bend the metal tabs
(90°) into place.

CD
Dashboard
@
Mounting
sleeve
• Make sure that the
unit
is
installed
securely in place.
An
unstable
installation may cause skipping or
other malfunctions.
When
not
using
the
supplied
mounting
sleeve
1
Determine
the
appropriate
position
where
the
holes
on
the
bracket
and
the
side
of
the
unit
match.
2
Tighten
two
screws on each side.
2
CD
Screw
@
Mounting
bracket
® Dashboard
or
console
•
Use
either truss
(5
mm x
9
mm) or
flush surface
(5
mm
x
9
mm) screws,
depending on
the
bracket screw
holes.
Removing
the
unit
(installed
with
the
supplied
mounting
sleeve)
1 Remove
the
trim
ring.
CD
Trim ring
@ Notched tab
• Releasing the
front
panel allows easier
access
to
the
trim
ring.
• When reattaching the
trim
ring,
point
the side with
the
notched tab down.
2
Insert
the
supplied extraction keys
into
both
sides
of
the
unit
until
they
click
into
place.
3 Pull
the
unit
out
of
the
dashboard.
To
secure
the
front
panel
The
front
panel can be secured
with
the
supplied screw.
~
CD
Screw
I
Additional
Information
The
display
automatically
returns
to
the
normal
display.
~
No operations have been made for
about
30
seconds.
-Perform
an
operation.
The repeat play range changes
unexpectedly.
---7
Depending on the repeat play range,
the selected range may change when
another folder ortrack
is
being selected
or
during fast forwarding/reversing.
-Select
the repeat play range again.
A
subfolder
is
not
played back.
---7
Subfolders cannot be played when
[FLO]
(folder repeat)
is
selected.
-Select
another repeat play range.
The sound
is
intermittent.
---7
You
are using adevice,
such
as
acellular
phone,
that
may cause audible
interference.
-Move
electrical devices that may be
causing the interference away from
the unit.
Common
AMP
ERROR
~This
unit
fails to operate
or
the speaker
connection
is
incorrect.
~The
protective circuit
is
activated.
-Check
the speaker connection.
-Turn
the ignition switch
OFF
and back
to
ON
again. Ifthe message remains,
contact your dealer or
an
authorized
Pioneer Service Station for assistance.
NO
XXXX
(NO
TITLE,
for example)
---7
There
is
no embedded text information.
-Switch
the display
or
play another
track/file.
CD
player
ERROR-07,
11, 12,
17,30
---7
The disc
is
dirty.
-Clean
the disc.
---7
The disc
is
scratched.
-Replace the disc.
ERROR-07,
10, 11, 12, 15, 17, 30,
AO
---7
There
is
an
electrical
or
mechanical
error.
-Turn
the ignition switch
OFF
and back
to
ON,
or switch
to
a different source,
then back
to
the
CD
player.
ERROR-15
---7
The inserted disc
is
blank.
-Replace the disc.
ERROR-23
~Unsupported
CD
format.
-Replace the disc.
FORMAT
READ
---7
Sometimes there
is
adelay between the
start
of
playback and when you start
to
hear any sound.
-Wait
untilthe message disappears and
you hear sound.
NO AUDIO
---7
The inserted disc does
not
contain any
playable files.
-Replace the disc.
SKIPPED
~The
inserted disc contains
DRM
protected files.
-The
protected files are skipped.
m
::::s
'9.
iii.
::::s-
En
15

PROTECT
~All the files on the inserted disc are
embedded
with DRM.
-Replace the disc.
USB device/iPod
FORMAT READ
~ Sometimes there is adelay between the
start
of playback and when you start to
hear any sound.
-Wait until the message disappears and
you hear sound.
NO AUDIO
~There are no songs.
-Transfer the audio files
to the USB
device and connect.
~The connected USB device has security
enabled.
-Follow the USB device instructions to
disable the security.
SKIPPED
~The connected USB device contains
DRM protected files.
-The protected files are skipped.
PROTECT
~ All the files on the connected USB
device are embedded with DRM.
-Replace the USB device.
N/A USB
~The connected USB device is not
supported by this unit.
-Disconnect your device and replace it
with acompatible USB device.
HUB ERROR
~The USB device connected via a USB
hub is not supported by this unit.
-Connect the USB device directly to this
unit using a USB cable.
CHECK USB
~The USB connector or USB cable has
short-circuited.
16 En
-Check that the USB connector or USB
cable is not caught in something or
damaged.
~The connected USB device consumes
more than maximum allowable current.
-Disconnect the USB device and do not
use it. Turn the ignition switch OFF
and back to ACC or ON. Connect only
compliant
USB devices.
~ The iPod operates correctly but does
not charge.
-Make sure the connection cable for
the iPod
has not shorted out (e.g., not
caught in metal objects). After
checking, turn the ignition switch
OFF
and back to ON, or disconnect the
iPod and reconnect.
ERROR-19
~ Communication failed.
-Perform one of the following
operations, then return
to the USB
source.
• Turn the ignition switch
OFF and
back
to ON.
• Disconnect the USB device.
• Change
to adifferent source.
~ iPod failure.
-Disconnect the cable from the iPod.
Once the iPod's main menu
is
displayed, reconnect the iPod and
reset it.
ERROR-23
~ USB device was not formatted properly.
-Format the USB device with FATl 2,
FATl 6 or FAT32.
ERROR-16
~The iPod firmware version is old.
-Update the iPod version.
~ iPod failure.
-Disconnect the cable from the iPod.
Once the iPod's main menu
is
displayed, reconnect the iPod and
reset it.
STOP
~There are no songs in the current list.
-Select a list that contains songs.
NOT FOUND
~ No related songs.
-Transfer songs
to the iPod.
Pandora
ERROR-19
~ Communication failed.
-Disconnect the cable from the device.
Once the device's main menu
is
displayed, reconnect the device and
reset it.
START UPAPP
~The Pandora application has not started
running yet.
-Start up the Pandora application.
RATING ERROR
~The thumb rating operation was
disabled.
-Run the same command for another
track.
CANT SKIP
~The skip operation was disabled.
-Run the same command for another
track.
TRY LATER
~ Unable to save thumb rating.
~Unable to save BookMark.
~ Unable to add station.
-Try again later.
MAINTENANCE
~ Pandora system is undergoing
maintenance.
-Try again later.
SKIP LIMIT
~ Due to music licensing restrictions,
Pandora limits the total
number of skips
per hour.
-Wait until Pandora allows you to skip
again.
UPDATE APP
~This version of the Pandora application
is not supported.
-Connect adevice that has a
compatible version
of the Pandora
application installed.
LOGIN ERROR
~ Your Pandora account is not logged in.
-Disconnect the cable from the device,
and log in
to your Pandora account.
Then reconnect the device.
CHECK DEVICE
~ Device error message displayed in the
Pandora application.
-Check the connected device.
PLEASE CREATE A STATION ON THE
PHONE
~ No station found.
-Create a station in the Pandora
application on your connected device.
SELECT STN
~ No station selected.
-Select a station.
STATION FULL
~ A new station cannot be added.
-Delete an old station to open a spot
for a new one.
CAN.T DELETE
~The station could not be deleted.
-Run the same command for another
station.
NO NETWORK
~The connected device is out of area.
-Connect the device to a network.
NO SERVICE IN THIS COUNTRY
~The connected device is out of area.
-Connect the device to a network.

STN
DELETED
--?The operation was disabled.
-Run
the
same command for another
station.
Apps
START
UPAPP
--?The application
has
not
started running
yet.
-Operate
the mobile device
to
start up
the application.
Spotify
CHECKAPP
--?
Connection
to
the Spotify application
failed.
-Follow
the instructions
that
appear on
the screen.
Discs and player
•
Use
only discs
that
feature either
of
the
following
two
logos.
cQJoo~rn
cQJo~rn
DIGITAL AUDIO DIGITAL AUDIO
I
TEXT
I
•
Use
12-cm discs.
•
Use
only conventionat fully circular discs.
• The following types
of
discs cannot be
used
with
this unit:
-DuaiDiscs
-8-cm discs: Attempts
to
use
such discs
with
an
adaptor may cause the
unit
to
malfunction.
-Oddly
shaped discs
-Discs otherthan
CDs
-Damaged
discs, including discs
that
are
cracked, chipped or warped
-CD-R/RW discs
that
have
not
been
finalized
•
Do
not
write on or applychemicals
to
the
surface
of
the discs.
•
To
clean a
CD,
wipe the disc with a soft
cloth outward from the center.
• Condensation may temporarily impair
the player's performance. Let
it
rest for
about one hour
to
adjust
to
awarmer
temperature.
Also,
wipe any damp discs
off
with
a soft cloth.
• When using discs
that
can be printed on
label surfaces, check the instructions and
the warnings
of
the
discs. Depending on
the discs, inserting and ejecting may
not
be possible. Using such discs may result
in damage
to
this equipment.
• Do
not
attach commercially available
labels or other materials
to
the discs.
-The
discs may warp making the disc
unplayable.
-The
labels may come
off
during
playback and prevent ejection
of
the
discs, which may result in damage
to
the
equipment.
USB
storage device
• Connections
via
USB
hubs are
not
supported.
• Firmly secure the
USB
storage device
before driving. Do
not
let
the
USB
storage
device fall
onto
the floor, where
it
may
become jammed under
the
brake or
accelerator pedal.
• Depending on the
USB
storage device,
the following problems may occur.
-Operations
may vary.
-The
storage device may
not
be
recognized.
-Files may
not
be played back properly.
-The
device may cause audible
interference when you are listening
to
the radio.
iPod
• Do
not
leave the iPod in places
with
high
temperatures.
• Firmly secure the iPod when driving. Do
not
let the iPod fall
onto
the floor, where
it
may becomejammed under the brake
or accelerator pedal.
• The settings
of
the iPod such
as
the
equalizer and repeat play
are
changed
automatically when the iPod
is
connected
to
the unit. Once the iPod
is
disconnected, those settings will return
to
the
original settings.
• Incompatible text saved on the iPod will
not
be displayed by the unit.
C~mp~e~s~#
audi()
compatibility
• Only the first
32
characters
can
be
displayed
as
afile name (including the file
extension) or afolder name.
• The
unit
may
not
work properly
depending on the application used
to
encode WMA files.
• There may be a slight delay at the start
of
the playback
of
audio files embedded
with
image data, or audio files stored on a
USB
device
with
numerous folder
hierarchies.
A
CAUTION
• Pioneer cannot guarantee compatibility
with
all
USB
mass
storage devices, and
assumes no responsibility for any
loss
of
data on media players, smartphones, or
other devices while using this product.
• Do
not
leave discs or a
USB
storage
device in any place
that
is
subject
to
high
temperatures.
WMAfiles
File extension .wma
Bit rate 48 kbps
to
320 kbps
(CBR),
48 kbps
to
384
kbps
(VBR)
Sampling
frequency
32
kHz,
44.1
kHz, 48
kHz
Windows
Media
TM
Not
compatible
Audio
Professional,
Lossless, Voice/ORM
Stream/Stream
with
video
MP3
files
File extension .mp3
Bit rate 8 kbps
to
320 kbps
(CBR),
VBR
Sampling
frequency
8 kHz
to
48 kHz (32
kHz,
44.1
kHz, 48 kHz
for
emphasis)
Compatible
103
tag
1.0,
1.1,
2.2,
2.3, 2.4
version
(103
tag Version 2.x
is
given
priority
over
Version
1.x.)
M3u
playlist
Not
compatible
MP3i (MP3
Not
compatible
interactive),
mp3
PRO
WAVfiles
•
WAV
file formats cannot be connected
via
MTP.
File extension .wav
Quantization
bits 8 and 16 (LPCM), 4
(MSAOPCM)
Sampling
frequency
16 kHz
to
48 kHz
(LPCM), 22.05 kHz and
44.1
kHz
(MS
AOPCM)
Disc
• Regardless
of
the length
of
the blank
section between the songs from the
original recording, compressed audio
discs play with a short pause between
songs.
Playable
folder
Up
to
eight
tiers
(A
hierarchy practical hierarchy
is
less
than
two
tiers.)
Playable folders
Up
to
99
IT
j
~
iii
:r
En
17

Playable files Up
to
999
File
system
ISO
9660
Levell
and
2,
Romeo, Joliet
Multi-session Compatible
playback
Packet write data Not compatible
transfer
USB
device
• There may be aslight delay
when
starting
playback
of
audio files on a
USB
storage
device
with
numerous folder hierarchies.
Playable folder Up
to
eight
tiers
(A
hierarchy practical hierarchy
is
less
than
two
tiers.)
Playable folders Up
to
500
Playable files Up
to
15
000
Playback
of
copyright- Not compatible
protected files
Partitioned
USB
Only the first
partition
device
can
be played.
This
unit
supports only the
following
iPod
models. Supported iPod software versions are
shown below. Older versions may
not
be
supported.
Made for
-iPod touch (1st
through
6th
generation)
- i
Pod
classic
-iPod
with
video
-iPod nano (1st
through
7th generation)
-iPhone
6s
-iPhone
6s
Plus
-iPhone 6
-iPhone 6
Plus
-iPhone
Ss
-iPhone
Sc
-iPhone
5
-iPhone
4s
-iPhone 4
-iPhone
3GS
-iPhone
3G
-iPhone
18
En
• Operations may vary depending on
the
generation
and/or
software version
of
the
iPod.
•
Users
of
iPod
with
the
Lightning
Connector should use the Lightning
to
USB
Cable (supplied
with
iPod).
•
Users
of
iPod
with
the
Dock Connector
should
use
the
CD-IU51.
For
details,
consult your dealer.
• Refer
to
the iPod manuals for information
about
the
file/format compatibility.
• Audiobook, Podcast: Compatible
A
CAUTION
Pioneer accepts no responsibility for data
lost on
the
iPod, even
if
that
data
is
lost
while this
unit
is
used.
The user cannotassign folder numbers and
specify playback sequences
with
this unit.
Sequence
of
audio file depends on
the
connected device.
Note
that
the hidden files in a
USB
device
cannot be played back.
Example
of
a hierarchy
L:JFolder
Jl
Compressed
.J1
CD
audiofile
]; @
Level
1
Level
2
Level
3
Level
4
01
to
OS:
Folder number
CD
to
®:
Playback sequence
iTunes
Apple and iTunes are trademarks
of
Apple
Inc., registered in
the
U.S.
and
other
countries.
WMA
Windows Media
is
either a registered
trademark or trademark
of
Microsoft
Corporation in
the
United States
and/or
other
countries.
This
product
includes technology owned
by Microsoft Corporation and cannot be
used or distributed
without
a license from
Microsoft Licensing, Inc.
iPod
&
iPhone
iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks
of
Apple Inc.,
registered in the
U.S.
and
other
countries.
Lightning
is
atrademark
of
Apple Inc.
"Made for iPod" and "Made for iPhone"
mean
that
an electronic accessory has
been designed
to
connect specifically
to
iPod or iPhone, respectively, and
has
been
certified by
the
developer
to
meet Apple
performance standards. Apple
is
not
responsible for
the
operation
of
this device
or its compliance
with
safety and
regulatory standards. Please note
that
the
use
of
this accessory
with
iPod
or
iPhone
may affect wireless performance.
Android &
Google
Play
Android, Google
Play,
and
the
Google Play
logo
are trademarks
of
Google Inc.
Pandora®
internet
radio
PANDORA,
the
PANDORA
logo, and
the
Pandora trade dress are trademarks or
registered trademarks
of
Pandora Media,
Inc. Used
with
permission.
Pandora
is
only
available in certain
countries.
Please
visit
http://www.pandora.com/legal
for more information.
MIXTRAX
MIXTRAX
is
atrademark
of
the
PIONEER
CORPORATION.
Spotify®
SPOTIFY
and
the
Spotify
logo
are among
the registered trademarks
of
Spotify
AB.
Compatible mobile digital devices and
premium subscription required, where
ava
i
Ia
ble,
see
https://www.spotify.com.
General
Power source: 14.4 V
DC
(1
0.8
V
to
15.1
V
allowable)
Grounding system: Negative
type
Maximum current consumption: 10.0 A
Dimensions (W x H x
D):
DIN
Chassis:
178
mm
x
SO
mm
x 165
mm
(7
in. x 2 in. x 6-1/2 in.)
Nose: 188
mm
x
58
mm
x
17
mm
(7-
3/8 in. x 2-1/4 in. x 5/8 in.)
D
Chassis:
178
mm
x
SO
mm
x 165
mm
(7
in. x 2 in. x 6-1/2 in.)
Nose: 170
mm
x 46
mm
x
17
mm
(6-
3/4 in. x 1-3/4in. x 5/8 in.)
Weight: 1kg (2.21bs)
Audio
Maximum power
output:
•
SOW
x 4 ch/4 0 (for no subwoofer)
•
50Wx2ch/40+70Wx
1
ch/20
(for subwoofer)
Continuous power
output:
22
W x 4
(SO
Hz
to
15 000
Hz,
5 %
THD,
4 0 load,
both
channels driven)
Load impedance: 4 0
(4
0
to
8 0 allowable)
Precut maximum
output
level:
2.0
V
Loudness
contour:+
10
dB (100Hz), +6.5
dB
(10kHz) (volume:
-30
dB)
Equalizer (5-Band Graphic Equalizer):
Frequency:
80
Hz/250 Hz/800 Hz/2.5
kHz/8kHz

Equalization range:
±12
dB
(2
dB step)
Subwoofer
(mono):
Frequency: 50 Hz/63 Hz/80 Hz/1 00
Hz/125
Hz/160
Hz/200 Hz
Slope:
-12
dB/oct,
-24
dB/oct
Gain:
+6
dB
to
-24
dB
Phase: Normal/Reverse
CD
player
System:
Compact
disc
audio
system
Usable discs:
Compact
disc
Signal-to-noise ratio: 94 dB
(1
kHz) (IHF-A
network)
Number
of
channels: 2 (stereo)
MP3
decoding
format:
MPEG-1
& 2
Audio
Layer 3
WMA
decoding
format:
Ver.
7,
7.1,
8,
9,
10,
11, 12
(2
ch
audio)
(Windows
Media
Player)
WAV signal
format:
Linear
PCM
&
MS
ADPCM (Non-compressed)
USB
USB
standard specification:
USB
2.0
full
speed
Maximum
current
supply:
1.5
A
USB
Protocol:
MSC
(Mass Storage Class)
MTP (Media Transfer Protocol)
AOA
(Android
Open
Accessory) 2.0
File system:
FAT12, FAT16,
FAT32
MP3
decoding
format:
MPEG-1
& 2
Audio
Layer3
WMA
decoding
format:
Ver.
7,
7.1,
8,
9,
10,
11, 12
(2
ch
audio)
(Windows
Media
Player)
WAV
signal
format:
Linear
PCM
&
MS
ADPCM (Non-compressed)
FM
tuner
Frequency range: 87.9
MHz
to
107.9 MHz
Usable sensitivity:
11
dBf
(1.0
~V/75
0,
mono,
SIN:
30 dB)
Signal-to-noise ratio: 72 dB (IHF-A
network)
AM
tuner
Frequency range:
530kHz
to
1
710kHz
Usable sensitivity: 25
~V
{S/N: 20 dB)
Signal-to-noise ratio:
62
dB (IHF-A
network)
CEA2006 Specifications
Power
output:
14 W
RMS
x 4 Channels (4 0
and~
1 % THD+N)
SIN
ratio:
91
dBA (reference: 1 W
into
4
0)
NOTE
Specifications
and
the
design
are
subject
to
modifications
without
notice.
En
19

Visit
our
website
I
Visitez
notre site
Web
I
Visite nuestro sitio
Web
Register yourproduct
at
Enregistrez votre produit
au
Registre su producto en
http://www.pioneerelectronics.com
in Canada
au Canada http://WWW.pioneerelectroniCS.C8
en Canada
-Learn
about product updates (such as firmware updates) for your
product.
-Register your product to receive notices about product updates and to
safeguard purchase details
in
our files
in
the event of loss or theft.
-Access
owner's manuals, spare parts information, service information,
and much more.
-lnformez-vous sur les mises a jour disponibles pour votre produit (telles
que les mises a jour du firmware).
-Enregistrez votre produit afin de recevoir des notifications concernant les
mises a jour du produit, ainsi que pour sauvegarder les details de votre
achat dans nos fichiers
en
cas de perte ou de vol.
-Accedez aux modes d'emploi, aux informations relatives aux pieces de
rechange
eta
l'entretien,
eta
beaucoup d'autres informations.
-lnformese de las ultimas actualizaciones (por ejemplo, actualizaciones
de firmware) para
su
producto.
-Registre
su
producto para recibir informacion sobre actualizaciones del
producto y para mantener
Ia
seguridad de los detalles de
su
compra en
nuestros archives en caso de perdida o robo.
-Acceso a manuales de instrucciones, informacion sobre piezas de
recambio y mucho mas.
©
2016
PIONEER
CORPORATION. All
rights
reserved.
© 2016
PIONEER
CORPORATION. Taus
droits
de
reproduction
et
de
traduction
reserves.
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, Japan
PIONEER ELECTRONICS (USA) INC.
P.O.
Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: [phone]
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit
2,
Markham, Ontario L3R 2Z5, Canada
TEL: [phone]
TEL: [phone] .
PIONEER EUROPE NV
Haven 1087, Keetberglaan
1,
B-9120 Melsele,Belgium/Belgique
TEL:
(0)
3/570.05.11 .
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat,
#07-01,
Singapore 159346
TEL: [phone]
PIONEER ELECTRONICS AUSTRALIA
PTY.
LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: [phone]
PIONEER ELECTRONICS DE MEXICO S.A. DE
C.V.
Blvd. Manuel Avila Camacho 138,
10
piso
Coi.Lomas de Chapultepec, Mexico,
D.F.
11000
Tel:
52-55-9178-4270,
Fax:
52-55-5202-3714
$t~~iffi~~,&1}
~
!s~tr=tJpg~M~IIffl:JIC~g4o75m8~
~~3:
886-(0)2-2657-3588
$t~~~
<
w~i)
~~.&1}
~
~~n~~~~~;~.trn9095m5ll
~~3
:
852-2848-6488
<QRD3375-A>
UC