Pioneer DVH-P5000UB User manual

MANUEL D’INSTALLATION
INSTALLATION MANUAL
English Español Deutsch Français Italiano Nederlands
DVH-P5000UB

1
Connecting the Units ................................ 1
Power cable connection .................................... 3
Connecting to separately sold power amp ........ 5
When connecting with a multi-channel
processor .................................................... 7
Connecting and installing the optical cable
connection box .......................................... 8
When using a display connected video
outputs ........................................................ 9
When connecting with a rear view camera .... 10
Installation ................................................ 11
DIN Front/Rear-mount .................................... 12
DIN Front-mount ............................................ 12
DIN Rear-mount .............................................. 13
Fastening the front panel ................................ 13
Connecting the Units
Contents
Note:
•When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.
•Use this unit in other than the following condi-
tions could result in fire or malfunction.
—Vehicles with a 12-volt battery and negative
grounding.
—Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
•To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
—Disconnect the negative terminal of the bat-
tery before installation.
—Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
—Place all cables away from moving parts,
such as gear shift and seat rails.
—Place all cables away from hot places, such as
near the heater outlet.
—Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
—Cover any disconnected cable connectors
with insulating tape.
—Do not remove RCA caps if RCA cables are
not used.
—Do not shorten any cables.
—Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
—Use a fuse of the rating prescribed.
—Never wire the speaker negative cable direct-
ly to ground.
—Never band together multiple speaker’s nega-
tive cables.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F

English Español Deutsch Français Italiano Nederlands
•Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
•Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
•IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
•Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.
2

3
Connecting the Units
Power cable connection
15 cm
1*
2*
4*
3*
5*
N
ote
:
D
e
p
en
di
n
g
on t
h
e
ki
n
d
o
f
ve
hi
c
l
e, t
h
e
function of 3* and 5* ma
y
be different. In
this case, be sure to connect 2* to 5* and 4*
to
3
*.
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if
this terminal is not in
use.
Yellow (3*)
Back-up (or
accessory)
Red (5*)
Accessory
(or back-up)
Yellow (2*)
Connect to the constant
12 V supply terminal.
Red (4*)
Connect to terminal controlled
by ignition switch (12 V DC).
N
ote
:
In some vehicles, the ISO connector
ma
y
b
e
di
v
id
e
d
i
nto two. In t
hi
s case,
be sure to connect to both connectors.
Speaker leads
White: Front left +
White/black: Front left ≠
Gray: Front right +
Gray/black: Front right ≠
Green: Rear left +or subwoofer +
Green/black: Rear left ≠or subwoofer ≠
Violet: Rear right +or subwoofer +
Violet/black: Rear right ≠or subwoofer ≠
Black (chassis ground)
Connect to a clean, paint-free metal location.
Antenna jack
Fuse (10 A)
Fuse resistor
When you connect the separately sold multi-channel
processor (DEQ-P6600) to this unit, do not connect
anything to the speaker leads and system remote
control (blue/white).

English Español Deutsch Français Italiano Nederlands
4
Violet/white
Of the two lead wires connected to the back lamp,
connect the one in which the voltage changes when
the gear shift is in the REVERSE (R) position.
For details, refer to page 10.
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
N
otes
:
•
C
h
an
g
e t
h
e
i
n
i
t
i
a
l
sett
i
n
g
o
f
t
hi
s un
i
t (re
f
er to t
h
e
O
p
eration Manual). The subwoofer out
p
ut of this
unit is monaural.
• When using a subwoofer of 70 W (2 Ω) , be sure to
connect with Violet and Violet/black leads of this
unit. Do not connect anything with Green and
Green/black leads.
Yellow/black
If you use an equipment with Mute function, wire
this lead to the Audio Mute lead on that equipment.
If not, keep the Audio Mute lead free of any
connections.
This product
H
ar
d
-w
i
re
d
remote contro
l
a
d
a
p
tor can
b
e
connecte
d
(so
ld
se
p
arate
ly
).
IP-BUS input
(Blue)
IP-BUS
cable
Multi-CD player
(sold separately)
Blue/white (6*)
20 cm
15 cm
US
B ca
ble
C
onnect to se
p
arate
ly
so
ld
USB
d
ev
i
ce.
1.
5
m
AUX jack (3.5 ø)
Use a mini plug cable
to connect with
auxiliary device.

5
Connecting the Units
Connecting to separately sold power amp
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.
Blue/white (6*)
Subwoofer output
Rear output
Front output
When you connect separately sold multi-channel
processor (e.g. DEQ-P6600) to this unit, do not
connect anything to the speaker leads and system
remote control (blue/white).
:
Wh
en
y
ou connect mu
l
t
i
-c
h
anne
l
p
rocessor to
t
hi
s un
i
t, se
p
arate
ly
so
ld
p
ower am
p
must
b
e
connecte
d
to mu
l
t
i
-c
h
anne
l
p
rocessor.
N
ot
e
:
Ch
an
g
e t
h
e
i
n
i
t
i
a
l
sett
i
n
g
o
f
t
hi
s
p
ro
d
uct (re
f
er
to the O
p
eration Manual).
The subwoofer output of this unit is monaural.
This product

English Español Deutsch Français Italiano Nederlands
6
Connect with RCA cables
(sold separately)
Perform these connections when
using the optional amplifier.
Power amp (sold
separately)
Power amp (sold
separately)
Power amp (sold
separately)
System remote control
Front speaker Front speaker
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
Subwoofer Subwoofer
Left Right
Rear speakerRear speaker

When connecting with a multi-channel processor
7
Connecting the Units
Blue
Black Blue
Blue
Video output
(VIDEO OUTPUT)
Video input
(VIDEO INPUT)
AV system display
(e.g. AVX-7600)
(sold separately)
DEQ output
RCA cable
(supplied)
Not used
RCA cable
(supplied with multi-
channel processor)
IP-BUS cable
(supplied with multi-channel
processor)
1.5 m
Multi-channel processor
(DEQ-P6600)
(sold separately)
IP-BUS cable
Multi-CD player
(sold separately)
Black
Optical cable connection
box (supplied with multi-
channel processor)
Optical cable
(supplied with multi-
channel processor)
This product
Black
Blue
15 cm
If AV system display (e.g. AVX-7600)
is combined with this unit, connect the
rear view camera to the AV system
display. For details concerning
connection methods, refer to AV system
display’s instruction manual.
If AV system display is not combined
with this unit, connect the rear view
camera to this unit’s video input. For
details concerning connection, refer to
page 10.
Rear view camera
To video output
RCA cable
(sold separately)
Video input 2
(VIDEO 2/BACK
CAMERA INPUT)

8
English Español Deutsch Français Italiano Nederlands
Connecting and installing the
optical cable connection box
WARNING
•Avoid installing this unit in locations where the
operation of safety devices such as airbags is pre-
vented by this unit. Otherwise, there is a danger of
a fatal accident.
•Avoid installing this unit in locations where the
operation of the brake may be prevented.
Otherwise, it may result in a traffic accident.
•Fix this unit securely with the hook and loop fas-
tener or lock tie. If this unit is loose, it disturbs
driving stability, which may result in a traffic acci-
dent.
CAUTION
•Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or other problems.
•Do not install this unit near the doors where rain-
water is likely to be spilled on the unit. Incursion
of water into the unit may cause smoke or fire.
Connecting the optical cable
1. Connect the optical cable and
ground lead to the main unit.
Connect the optical cable so that it
does not protrude from the unit, as
shown in the illustration. Fasten the
ground lead to the protrusion on the
back of the unit.
2. Connect the optical cable to the
optical cable connection box.
Installing the optical cable
connection box
• When installing the optical cable
connection box with the hook and
loop fastener.
Install the optical cable connection box
using the hook and loop fastener in the
ample space of the console box.
•When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
Screw
Optical cable
Hook fastener
Loop fastener
Wrap with the protection tape
Fasten with the lock tie

9
Connecting the Units
When using a display connected video outputs
WARNING
NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while Driving.
Di
s
pl
a
y
w
i
t
h
RCA
i
n
p
ut
j
ac
ks
To v
id
eo
i
n
p
u
t
R
C
A ca
bl
e
(
su
ppli
e
d
)
1.
5
m
Video output
(VIDEO OUTPUT)
This product
15 cm

10
English Español Deutsch Français Italiano Nederlands
When connecting with a rear view camera
When this product is used with a rear view camera, it is possible to automatically switch
from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
•The screen image may appear reversed.
•The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing into a
tight parking spot. Do not use this function for entertainment purposes.
•The object in rear view may appear closer or more distant than in reality.
CAUTION
You must use a camera
which outputs mirror
reversed images.
Rear view camera
RCA cable
(sold separately)
To video output
Extension lead (supplied)
Fuse resistor
Connection method
Note:
It is necessary to set VIDEO IN to CAMERA in initial settings when connecting the rear view
camera.
2. Clamp firmly with
needle-nosed
pliers.
1. Clamp the lead.
8 m
15 cm
Video input
(VIDEO INPUT or REAR
VIEW CAMERA INPUT)
Violet/white
Of the two lead wires connected to the back lamp, connect the one in
which the voltage changes when the gear shift is in the REVERSE (R)
position. This connection enables the unit to sense whether the car is
moving forwards or backwards.
This product
15 cm

11
Installation
Note:
•Check all connections and systems before final
installation.
•Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•Do not install this unit where:
—it may interfere with operation of the vehicle.
—it may cause injury to a passenger as a result
of a sudden stop.
•The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•Optimum performance is obtained when the unit
is installed at an angle of less than 30°.
•The cords must not cover up the area shown in
the figure below. This is necessary to allow the
amplifires to radiate freely.
•When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
Do not close this area.

DIN Front/Rear-mount
This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.
DIN Front-mount
Installation with the rubber bush
1. Insert the mounting sleeve into the dashboard.
•When installing in a shallow space, use a sup-
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by using a screw-
driver to bend the metal tabs (90°) into place.
3. Install the unit as illustrated.
Removing the Unit
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•It becomes easy to remove the trim ring if the
front panel is released.
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
53
53
1
1
182182
12
Trim ring
English Español Deutsch Français Italiano Nederlands
Rubber bush
Screw
Dashboard Mounting sleeve

13
Installation
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•It becomes easy to remove the trim ring if the
front panel is released.
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.
3. Tighten two screws on each side.
•Use either truss screws (5 mm ×8 mm) or
flush surface screws (5 mm ×9 mm), depend-
ing on the shape of screw holes in the
bracket.
Fastening the front panel
If you do not plan to detach the front panel, the
front panel can be fastened with supplied screws
and holders.
1. Attach the holders to both sides of the front
panel.
2. Replace the front panel to the unit.
3. Flip the holders into upright positions.
4. Fix the front panel to the unit using screws.
Trim ring
Screw
Dashboard or Console
Factory radio mounting bracket
Screw
Holder

14
English Español Deutsch Français Italiano Nederlands

1
Conexión de las unidades ........................ 1
Conexión del cable de alimentación .................. 3
Conexión al amplificador de potencia vendido
separadamente ............................................ 5
Cuando conecte con un procesador
multicanal .................................................. 7
Conexión e instalación de la caja de conexión
de cable óptico ............................................ 8
Cuando utilice una pantalla
conectada a las salidas de vídeo ................ 9
Cuando conecte con una cámara de
vista trasera .............................................. 10
Instalación ................................................ 11
Montaje delantero/trasero DIN ........................ 12
Montaje delantero DIN .................................... 12
Montaje trasero DIN ........................................ 13
Fijación del panel delantero ............................ 13
Conexión de las unidades
Contenido
Nota:
•Cuando se instale esta unidad en un vehículo sin
la posición ACC (accesorio) en el interruptor de
encendido, se debe conectar el cable rojo al
terminal que puede detectar la operación de la
llave de encendido.
De lo contrario, la batería puede descargarse.
•El uso de esta unidad en condiciones diferentes
de las siguientes podría causar un fuego o fallo
de funcionamiento.
—Vehículos con una batería de 12 voltios y
puesta a tierra negativa.
—Altavoz con 50 W (valor de salida) y de 4 a 8
ohmios (valor de impedancia).
•Para prevenir cortocircuitos, sobrecalentamiento
o fallo de funcionamiento, asegúrese de seguir
las instrucciones a continuación.
—Desenchufe el terminal negativo de la batería
antes de la instalación.
—Fije el cableado con abrazaderas de cable o
con cinta adhesiva. Para proteger el cableado,
envuélvalo con cinta adhesiva donde el
cableado se apoya sobre piezas metálicas.
—Posicione todos los cables alejados de las
piezas móviles, como el cambio de marchas y
rieles de los asientos.
—Posicione todos los cables alejados de lugares
calientes como cerca de la salida del
calentador.
—No pase el cable amarillo a través de un
agujero en el compartimiento del motor para
conectar la batería.
—Cubra cualquier conector de cable
desconectado con cinta de aislamiento.
—No extraiga las tapas RCA si no se utilizan
los cables RCA.
—No acorte ningún cable.
—No corte nunca el aislamiento del cable de
alimentación de esta unidad para compartir la
energía con otro equipo. La capacidad de
corriente del cable es limitada.
—Utilice un fusible con la capacidad
especificada.
—No conecte nunca el cable negativo de
altavoz directamente a la puesta a tierra.
Sin posición ACCPosición ACC
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F

English Español Deutsch Français Italiano Nederlands
—No junte nunca múltiples cables negativos de
altavoz.
•La señal de control se emite a través del cable
azul/blanco cuando se enciende esta unidad.
Conéctelo a un terminal de control de sistema de
amplificador de potencia externo o al terminal de
control de relé de antena automática del vehículo
(máx. 300 mA, 12 V CC). Si el vehículo está
equipado con una antena de vidrio, conéctelo al
terminal de suministro de potencia de refuerzo de
la antena.
•No conecte nunca el cable azul/blanco al terminal
de alimentación de un amplificador de potencia
externo. Igualmente, no conéctelo nunca al
terminal de alimentación de la antena automática.
De lo contrario, puede ocurrir la descarga de la
batería o un fallo de funcionamiento.
•Los conectores IP-BUS están codificados en
colores. Asegúrese de conectar los conectores del
mismo color.
•El cable negro es para la puesta a tierra. Se debe
conectar este cable y el cable de puesta a tierra de
otro producto (especialmente de productos de alta
corriente como un amplificador de potencia)
separadamente. De lo contrario, puede ocurrir un
fuego o fallo de funcionamiento si los cables se
sueltan accidentalmente.
2

3
Conexión de las unidades
15 cm
1*
2*
4*
3*
5*
Nota:
Dependiendo del tipo de vehículo, la
función de 3* y 5* puede ser diferente. En
este caso, asegúrese de conectar 2* a 5* y
4* a 3*.
Conecte los conductores del
mismo color uno a otro.
Tapa (1*)
No quite la tapa cuando
no se utiliza este
terminal.
Toma de antena
Fusible (10 A)
Resistencia de fusible
Cuando conecte el procesador multicanal (DEQ-
P6600) vendido separadamente a esta unidad, no
conecte nada a los conductores de los altavoces y al
control remoto del sistema (azul/blanco).
Amarillo (3*)
Reserva
(o accesorio)
Rojo (5*)
Accesorio
(o reserva)
Amarillo (2*)
Conecte el terminal de
suministro de 12 V constante.
Rojo (4*)
Conecte al terminal controlado
por del interruptor de encendido
(12 V CC).
Negro (masa de la carrocería)
Conecte a un punto de metal limpio, libre de pintura.
Conector ISO
Nota:
En algunos vehículos, el conector ISO
puede estar dividido en dos partes.
En este caso, asegúrese de conectar a
ambos conectores.
Hilos de altavoz
Blanco: Izquierda delantera +
Blanco/negro: Izquierda delantera ≠
Gris: Derecha delantera +
Gris/negro: Derecha delantera ≠
Verde: Izquierda trasera +o
altavoz de subgraves +
Verde/negro: Izquierda trasera ≠o
altavoz de subgraves ≠
Violeta: Derecha trasera +o
altavoz de subgraves +
Violeta/negro: Derecha trasera ≠o
altavoz de subgraves ≠
Conexión del cable de alimentación

English Español Deutsch Français Italiano Nederlands
4
20 cm
15 cm
1,5 m
Toma AUX (3,5 ø)
Utilice un cable con
enchufe miniatura para
conectar a un equipo
auxiliar.
Violeta/blanco
De los dos conductores conectados a la lámpara trasera,
conecte el conductor cuyo voltaje cambia cuando se
desplaza la palanca de cambio de marcha a la posición
REVERSE (R).
Para los detalles, refiérase a la página 10.
Entrada IP-BUS
(Azul) Entrada remota cableada
Se puede conectar el adaptador de control
remoto cableado (vendido separadamente).
Este producto
Cable IP-BUS
Reproductor de
Multi-CD (vendido
separadamente)
Notas:
• Cambie el ajuste inicial de esta unidad (refiérase al
manual de operación). La salida de altavoz de
subgraves de esta unidad es monofónica.
• Cuando utilice un altavoz de subgraves de 70 W (2
Ω), asegúrese de conectarlo con los hilos Violeta y
Violeta/negro de esta unidad. No conecte nada con
los hilos Verde y Verde/negro.
La posición de los contactos del conector ISO
difiere dependiendo del tipo del vehículo. Conecte
6* y 7* cuando el contacto 5 es del tipo de control
de antena. En otros tipos de vehículo, no conecte
nunca 6* y 7*.
Azul/blanco
Conecte al terminal de control de sistema del
amplificador de potencia (máx. 300 mA 12 V CC).
Amarillo/negro
Si se utiliza un equipo con función de silenciamiento,
conecte este conductor con el conductor de
silenciamiento de audio en tal equipo. Si no, mantenga el
enmudecimiento de audio libre de cualquier conexión.
Azul/blanco (7*)
Conecte al terminal de control de relé
de antena automática (máx. 300 mA
12 V CC).
Azul/blanco (6*)
Cable USB
Conecte al dispositivo USB vendido
separadamente.

5
Conexión de las unidades
Azul/blanco
Conecte al terminal de control de sistema del
amplificador de potencia (máx. 300 mA 12 V CC).
Salida de altavoz de
subgraves
Salida trasera
Salida delantera
Cuando conecte el procesador multicanal
(DEQ-P6600) vendido separadamente a esta unidad,
no conecte nada a los conductores de los altavoces y
al control remoto del sistema (azul/blanco).
Nota:
Cuando conecte el procesador multicanal a esta
unidad, se debe conectar el amplificador de potencia
vendido separadamente al procesador multicanal.
Nota:
Cambie el ajuste inicial de este producto (refiérase al
manual de operación). La salida de altavoz de
subgraves de esta unidad es monofónica.
Este producto
La posición de los contactos del
conector ISO difiere dependiendo del
tipo del vehículo. Conecte 6* y 7*
cuando el contacto 5 es del tipo de
control de antena. En otros tipos de
vehículo, no conecte nunca 6* y 7*.
Azul/blanco (7*)
Conecte al terminal de control de relé de
antena automática (máx. 300 mA 12 V CC).
Azul/blanco (6*)
Conexión al amplificador de potencia vendido separadamente