Pioneer FX-MG8667DVZT/EW User manual

ORDER NO.
CRT3571
RX350
AUDIO SYSTEM
HEAD UNIT
CRT3571
PUB.NO.
Manufactured for TOYOTA
by PIONEER CORPORATION
VEHICLE DESTINATION PRODUCED
AFTER OEM PARTS No. ID No. PIONEER MODEL No.
RX350 EUROPE January 2006 86120-48A90 P3501 FX-MG8667DVZT/EW
RX350 EUROPE January 2006 86120-48D10 P3501 FX-MG8667DVZT91/EW
RX350 EUROPE January 2006 86120-48A60 P3500 FX-MG8767DVZT/EW
RX350 EUROPE January 2006 86120-48C80 P3500 FX-MG8767DVZT91/EW

FX-MG8667DVZT/EW
2
1234
1234
C
D
F
A
B
E
FX-MG8667DVZT/EW
This service manual should be used together with the following manual(s):
FX-MG8767DVZT/EW
ID No.P3500
FX-MG8667DVZT/EW
ID No.P3501
Model No. Order No. Mech.Module Remarks
CX-3150 CRT3495 MG4 DVD Mech. Module:Circuit Description, Mech. Description, Disassembly,etc.
CX-1011 CRT2406 3L Casseette Mech. Module:Mech. Description, Disassembly
"DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems,Inc.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
For details, refer to "Important Check Points for Good Servicing".
Supplementary model is identical to the original except for the addition of following items.
*:Non spare part
Description FX-MG8667DVZT91/EW
FX-MG8767DVZT91/EW
Cover CEG1045 (x2)
Cover CEG1324
Carton CHG4861
Contain Box CHL4861 (x1/2)
Air Cap * CHW1945

FX-MG8667DVZT/EW 3
5678
5678
C
D
F
A
B
E
SAFETY INFORMATION
-DVD and CD section precaution
1. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside the unit.
2. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY" .
3. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector
is plugged or unplugged.
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
1. Safety Precautions for those who Service this Unit.
• Follow the adjustment steps in the service manual when servicing this unit. When check
ing or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results.
Caution:
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
2. Make sure to install grille when charging power.
(* If you fail to do so, the main body will identify it as “a model without display” and the button will
not function. )
-Service Precautions
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
3. Do not disassemble the panel assy.
The button parts are greased by machine in order to give users comfortable touch.
When the panel assy needs to be dismantled for repairs, change the panel assy itself.
4. The test mode is not available on this unit.
To enter the test mode, load the mechanism to other unit designated for test mode and then try the mode by
referring to its service manual.

FX-MG8667DVZT/EW
4
1234
1234
C
D
F
A
B
E
On the top of the player.
CAUTION :
VORSICHT :
ADVARSEL :
VARNING :
VARO! :
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG, WENN
ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETZEN!
SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING
UNDGÅ UDSÆTTELSE FOR STRÀLING.
SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN.
AVATTAESSA ALTISTUT NÄKYVÄ JA NÄKYMÄTTÖMÄLLE
LASERSATEIL YLLE. ÄLÄ KATSO SÄTEESEN. VRW1860
CLASS 1
LASER PRODUCT
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
Laser diode characteristics
Wave length:
DVD:640~660nm
CD:770~810nm
DVD : 2.48mW(Emitting period :9sec.)
CD : 705 W(Emitting period : unlimited)
Additional Laser Caution
Transistors Q1101 and Q1102 in PCB drive the laser diodes for DVD and CD
respectively. When Q1101 or Q1102 is shorted between their terminals,
the laser diodes for DVD or CD will radiate beam. If the top cover is removed
with no disc loaded while such short-circuit is continued, the naked eyes may
be exposed to the laser beam.

FX-MG8667DVZT/EW 5
5678
5678
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

FX-MG8667DVZT/EW
6
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 3
1. SPECIFICATIONS ............................................................................................................................................ 7
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 EXTERIOR(1) ............................................................................................................................................ 8
2.2 EXTERIOR(2) .......................................................................................................................................... 10
2.3 DVD MECHANISM MODULE .................................................................................................................. 12
2.4 CASSETTE MECHANISM MODULE....................................................................................................... 14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................16
3.1 BLOCK DIAGRAM ................................................................................................................................... 16
3.2 MAIN UNIT(1/3)(GUIDE PAGE)............................................................................................................... 24
3.3 MAIN UNIT(2/3)(GUIDE PAGE)............................................................................................................... 30
3.4 MAIN UNIT(3/3)(GUIDE PAGE)............................................................................................................... 36
3.5 KEYBOARD PCB..................................................................................................................................... 42
3.6 CONNECTOR1 PCB................................................................................................................................ 44
3.7 CONNECTOR2 PCB................................................................................................................................ 45
3.8 DVD CORE UNIT(1/2)(GUIDE PAGE) ..................................................................................................... 46
3.9 DVD CORE PCB(2/2)............................................................................................................................... 52
3.10 L PCB..................................................................................................................................................... 56
3.11 R PCB .................................................................................................................................................... 57
3.12 CASSETTE MECHANISM MODULE..................................................................................................... 58
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 62
4.1 MAIN UNIT............................................................................................................................................... 62
4.2 KEYBOARD PCB..................................................................................................................................... 66
4.3 CONNECTOR1 PCB................................................................................................................................ 70
4.4 CONNECTOR2 PCB................................................................................................................................ 71
4.5 DVD CORE UNIT ..................................................................................................................................... 72
4.6 PCB ASSY ............................................................................................................................................... 76
4.7 L PCB....................................................................................................................................................... 77
4.8 R PCB ...................................................................................................................................................... 78
4.9 DECK UNIT.............................................................................................................................................. 79
4.10 SENSOR UNIT ...................................................................................................................................... 80
5. ELECTRICAL PARTS LIST ............................................................................................................................ 81
6. ADJUSTMENT ............................................................................................................................................... 98
6.1 JIG CONNECTION DIAGRAM................................................................................................................. 98
6.2 DOLBY ADJUSTMENT............................................................................................................................ 99
6.3 TEST MODE .......................................................................................................................................... 100
7. GENERAL INFORMATION........................................................................................................................... 108
7.1 DIAGNOSIS ........................................................................................................................................... 108
7.1.1 AVC-LAN DIAGNOSIS MODE ............................................................................................................ 108
7.1.2 DISASSEMBLY ................................................................................................................................... 115
7.1.3 CONNECTOR FUNCTION DESCRIPTION........................................................................................ 118
7.2 PARTS.................................................................................................................................................... 119
7.2.1 IC ........................................................................................................................................................ 119
7.2.2 DISPLAY ............................................................................................................................................. 131
7.3 EXPLANATION ...................................................................................................................................... 132
7.3.1 OPERATIONAL FLOW CHART .......................................................................................................... 132
7.3.2 SYSTEM BLOCK DIAGRAM .............................................................................................................. 133
8. OPERATIONS .............................................................................................................................................. 134
is a trademark of DVD Format/Logo Licensing Corporation.
2.0 CHANNEL

FX-MG8667DVZT/EW 7
5678
5678
C
D
F
A
B
E
1. SPECIFICATIONS
General
Power source........................................................................................................13.2V DC(10.5–16.0 V allowable)
Grounding system..............................................................................................................................Negative type
Backup current..................................................................................................................................0.15mAor less
Weight...........................................................................................................................................3,177g
DVD player
System....................................................................DVD video, DVD audio, Video CD, Compact disc audio system
Region number...................................................................................................................................................2
Usable discs..........................................................................DVD video, DVD audio, Video CD and Compact disc
Video
VideoS/N..............................................................................................................................................50dBormore
Audio
Distortion...............................................................................................................................................0.2% or less
S/N......................................................................................................................................................80dB or more
Separation..........................................................................................................................................65dB or more
Stereobalance........................................................................................................................................±2dB within
Dynamic range....................................................................................................................................80dB or more
Cassette player
Tape....................................................................................................................Compact cassette tape(C30–C90)
Tapespeed................................................................................................4.76cm/sec.(+0.14cm/sec.,-0.05cm/sec.)
Wow and flutter.......................................................................................................................0.2% or less(WRMS)
Distortion.................................................................................................................................................3% or less
S/N....................................................................................................................................................40dB or more
Crosstalk...........................................................................................................................................40dB or more
Stereo Separation..............................................................................................................................30dB or more
FM tuner
Frequency...............................................87.5–108.0 MHz
S/N..............................................................46dB or more
Distortion.......................................................1.5% or less
Image interference.......................................35dB or more
IF interference..............................................80dB or more
AM(MW) tuner
Frequency...................................................522–1,611kHz
S/N...............................................................42dB or more
Distortion........................................................1.5% or less
IF interference..............................................55dB or more
Image interference........................................45dB or more
LW tuner
Frequency.....................................................153–279 kHz
S/N...............................................................42dB or more
Distortion........................................................1.5% or less
IF interference..............................................55dB or more
Image interference........................................45dB or more

FX-MG8667DVZT/EW
8
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 EXTERIOR(1)
N
OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The >mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
"

FX-MG8667DVZT/EW 9
5678
5678
C
D
F
A
B
E
EXTERIOR(1) SECTION PARTS LIST
Mark No. Description Part No.
1 Screw(Except -91 model) BMZ50P080FTC
2 Screw BSZ26P040FTC
3 86211-48030-A(Except -91 model) CND1247
4 86212-48030-A(Except -91 model) CND1248
5 90467-10203 CNV5641
6 Guide CNV7306
7 Screw BMZ30P040FTC
8 Screw BSZ26P040FTC
9 Screw(M2.6x10) CBA1964
10 Connector CDE7679
11 Connector CDE7684
12 Cord Assy CDE8026
13 Chassis CNA2869
14 Case CNB3049
15 Holder CNB3226
16 Holder CND2427
17 Holder CND2531
18 Holder CND2721
19 Earth Plate CND3060
20 Cushion CNM9507
21 Cushion CNM9842
22 Insulator CNM9843
23 Insulator CNM9844
24 Conductive Cushion CNM9847
25 Insulator CNM9905
26 Holder CNV8764
27 Holder CNV8807
28 Plate CNV8808
29 Connector Unit CWM9654
30 Screw(M3x6) CBA1393
31 Connector CDE7686
32 Connector CDE8029
33 Connector(CN1002) CKM1470
34 Connector(CN1102) CKM1480
35 Connector(CN1103) CKS4822
36 Connector(CN1005) CKS5244
37 Connector(CN1104) CKS5244
38 Connector(CN1003) CKS5251
39 Socket(CN1101) CKS5316
40 Holder CND2433
41 Main Unit CWN1110
42 Screw ASZ26P060FTC
43 Screw BMZ30P040FTC
44 Screw(M3x6) CBA1393
45 Terminal(CN101) CKF1064
46 Terminal(CN304) CKF1064
47 Connector(CN301) CKM1466
48 Connector(CN303) CKM1467
49 Connector(CN302) CKM1469
50 Connector(CN408) CKS4266
51 Connector(CN501) CKS4853
52 Connector(CN407) CKS4958
53 Connector(CN403) CKS5279
54 Connector(CN404) CKS5280
55 Connector(ANT11) CKX1064
56 Holder CND2431
57 Holder CND2432
58 Holder CND2434
59 Shield CND2436
60 Shield CND3061
61 Insulator CNM9861
62 FM/AM Tuner Unit CWE1839
63 Holder CND2144
64 Connector(CN701) VKN1940
65 Chassis Unit CXC5466
66 Mechanism Module(Service) CXX2102
67 Fan Motor CXM1336
68 Cassette Mechanism Module EXK4298
69 Screw ISS26P050FTC
70 Screw PMH26P060FTC
71 Label CRW1455
72 Knob Unit CXC4801
73 Spring CBL1711
74 Frame Unit CXC4809
75 Door Unit CXC4846
76 Screw IMS20P022FTC
77 Screw IMS26P060FTC
78 Transistor(Q755) 2SB1185
79 Door CAT2730
80 Spring CBL1727
81 Cushion CNN1205
82 Cushion CNN1207
83 Sheet CNN1208
84 Label VRW1860
85 Screw BSZ26P050FTC
Mark No. Description Part No.

FX-MG8667DVZT/EW
10
1234
1234
C
D
F
A
B
E
2.2 EXTERIOR(2)

FX-MG8667DVZT/EW 11
5678
5678
C
D
F
A
B
E
(1)EXTERIOR(2) SECTION PARTS LIST
(2) CONTRAST TABLE
FX-MG8667DVZT/EW,FX-MG8667DVZT91/EW,FX-MG8767DVZT/EW and FX-MG8767DVZT91/EW are con-
structed the same except for the following:
Mark No. Description Part No.
1 Grille Assy See Contrast table(2)
2 Screw BPZ20P080FTC
3 Button(AF•TA) See Contrast table(2)
4 Button(SEEK•TRACK) See Contrast table(2)
5 Button(TEXT) See Contrast table(2)
6 Button(TAPE EJECT) See Contrast table(2)
7 Button(LOAD) See Contrast table(2)
8 Button(PTY) See Contrast table(2)
9 Button(DISC EJECT) See Contrast table(2)
10 Button(AST) See Contrast table(2)
11 Lighting Conductor CNV8527
12 Lighting Conductor CNV8528
13 Lighting Conductor CNV8529
14 Lighting Conductor CNV8530
15 Lighting Conductor CNV8532
16 Lighting Conductor CNV8678
17 Lighting Conductor CNV8679
18 LCD(LCD801) CAW1867
19 Connector(CN802) CKS4771
20 Connector(CN980) CKS5202
21 Connector(CN990) CKS5202
22 Connector(CN801) CKS5203
23 Connector(CN803) CKS5203
24 Holder CND2773
25 Sheet CNM9563
26 Rubber CNV8536
27 Rubber CNV8537
28 Rubber CNV8538
29 Lighting Conductor CNV8539
30 Connector CNV8540
31 Grille Assy See Contrast table(2)
32 Button(DISC) See Contrast table(2)
33 Button(TAPE) See Contrast table(2)
34 Button(FM) See Contrast table(2)
35 Button(AM) See Contrast table(2)
36 Button(1) CAC9217
37 Button(2) CAC9218
38 Button(3) CAC9219
39 Button(4) CAC9220
40 Button(5) CAC9221
41 Button(6) CAC9222
42 Door See Contrast table(2)
43 Spring CBH2663
44 Lighting Conductor CNV8533
45 Holder Unit CXC6105
Mark No. Description Part No.
Mark No. Description FX-MG8667DVZT/EW
FX-MG8667DVZT91/EW
FX-MG8767DVZT/EW
FX-MG8767DVZT91/EW
1 Grille Assy CXC4733 CXC4732
3 Button(AF•TA) CAC9254 CAC9205(SEEK•TRACK)
4 Button(SEEK•TRACK) CAC9253 CAC9252(AF•TA)
5 Button(TEXT) CAC9242 CAC9211(TAPE EJECT)
6 Button(TAPE EJECT) CAC9241 CAC9212(TEXT)
7 Button(LOAD) CAC9244 CAC9213(DISC EJECT)
8 Button(PTY) CAC9248 CAC9245(AST)
9 Button(DISC EJECT) CAC9243 CAC9215(LOAD)
10 Button(AST) CAC9247 CAC9246(PTY)
31 Grille Assy CXC4776 CXC4775
32 Button(DISC) CAC9236 CAC9232(AM)
33 Button(TAPE) CAC9235 CAC9208(FM)
34 Button(FM) CAC9234 CAC9209(TAPE)
35 Button(AM) CAC9233 CAC9210(DISC)
42 Door CAT2695 CAT2694

FX-MG8667DVZT/EW
12
1234
1234
C
D
F
A
B
E
2.3 DVD MECHANISM MODULE
G
F
E

FX-MG8667DVZT/EW 13
5678
5678
C
D
F
A
B
E
DVD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No.
1 DVD Core Unit CWX3050
2 Terminal(CN1902) CKF1064
3 Connector(CN1901) CKS3971
4 Connector(CN1201) CKS4273
5 Connector(CN1903) CKS4374
6 Connector(CN2001) CKS4374
7 Connector(CN1881) CKS4426
8 Connector(CN1101) CKS4625
9 Connector(CN1551) CKS4817
10 Mechanism Unit(Service) CXX2097
11 Screw BMZ20P025FTC
12 Screw(M2x2.5) CBA1623
13 Screw(M2x2.5) CBA1823
14 Washer CBF1064
15 Washer CBF1094
16 Spring CBH2720
17 Spring CBH2731
18 Spring CBH2732
19 Variable Resistor(VR13) CCW1029
* 20 Gear CND1924
* 21 Arm CND1926
22 Stair CND1930
23 Stair CND1931
24 Stair CND1932
* 25 Arm CND1933
* 26 Gear CND1936
* 27 Gear CND1937
28 Gear CND1939
29 Case CND2656
30 Plate CND2902
31 Sheet CNM9746
32 Sheet CNM9774
33 Arm CNV7850
34 Gear CNV7851
35 Gear CNV7854
36 Gear CNV7856
37 Holder CNV7861
38 Cam CNV7866
39 Cam CNV7867
40 Cam CNV7868
41 Arm CNV7869
42 Cam CNV7932
43 PCB Assy CWX2986
* 44 Lever Unit CXC2392
* 45 Lever Unit CXC2393
* 46 Cam Gear Unit CXC2435
47 Sheet CNN1064
48 PCB Assy CXC3142
* 49 Chassis Unit CXC4341
50 Holder Unit CXC4342
51 Stage Assy(Service) CXX1957
52 ELV Motor Assy(M2) CXC4350
53 Screw JFZ20P020FTC
54 Cam Motor Assy(M1) CXC4349
55 Screw IMS26P025FTC
56 Tray Assy CXC4354
57 Lower Tray Assy CXC6755
58 Shutter Assy CXC4411
59 Washer YE15FTC
Mark No. Description Part No.

FX-MG8667DVZT/EW
14
1234
1234
C
D
F
A
B
E
2.4 CASSETTE MECHANISM MODULE
For grease application, refer to the service manual for CX-1011 (CRT2406).
I
J

FX-MG8667DVZT/EW 15
5678
5678
C
D
F
A
B
E
CASSETTE MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No.
1 Screw BSZ20P040FTC
2 Washer CBF1037
3 Washer CBG1003
4 Screw EBA1028
5 Screw BMZ20P022FTC
6 Spring EBH1653
7 Spring EBH1642
8 Spring EBH1641
9 Spring EBH1626
10 Spring EBH1627
11 Spring EBH1648
12 Cord EDD1024
13 Photo-reflector(Q101) EGN1004
14 Arm ENC1526
15 Lever Unit EXA1610
16 Lever ENC1543
17 Arm ENC1532
18 Frame ENC1533
19 Holder ENC1547
20 Gear ENC1535
21 Arm ENC1550
22 Roller ENR1040
23 Belt ENT1027
24 Collar ENV1508
25 Arm ENV1539
26 Arm ENV1540
27 Gear ENV1569
28 Gear ENV1547
29 Gear ENR1044
30 Worm Wheel ENV1559
31 Lever ENV1551
32 Flywheel ENV1607
33 Gathering PCB ENX1073
34 Switch(S101,S102,S103) ESG1007
35 Deck Unit EWM1055
36 Plug(CN251) EKS1026
37 Gathering PCB ENX1080
38 Motor Unit(M1) EXA1618
39 Motor EXM1035
40 Head Assy(HD1) EXA1594
41 Arm ENC1537
42 Screw EBA1031
43 Bracket ENC1559
44 Chassis Unit EXA1636
45 Pinch Holder Unit EXA1608
46 Pinch Roller ENV1518
47 Pinch Holder Unit EXA1607
48 Pinch Roller ENV1518
49 Reel Unit EXA1625
50 Head Base Unit EXA1611
51 Lever Unit EXA1587
52 Gear Unit EXA1632
53 Motor Unit(M2) EXA1660
54 Washer HBF-179
55 Spring EBH1537
56 Worm Gear ENV1564
57 Spring EBH1672
58 Lever ENC1548
59 Washer YE15FTC
60 Tube ENM1039
61 Spring EBH1645
62 Spring EBH1545
63 Sensor Unit EWM1057
Mark No. Description Part No.

FX-MG8667DVZT/EW
16
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
Q106
ANT11
MAIN
SUB
ANNTENA Q12
TU10V
Q15 Q16
Q13
Q14
Q23
MAINFIX
D11
Q11
MMAIN
SMAIN
Q18
TU10V
Q21 Q22
Q19
Q20
D15
D102
Q17
MSUB
MAIN DIVERSITY
SUB DIVERSITY
SSUB
9
8
3
4
17
13
22
Q102
AMPW
(2/2)
A
FMANT
Y101
1
14
AMANT
Q103
Q104
AUD8.4
VDD33
AC5
VCC
VDD3.3
DIVER
ROMVDD
23 LCH
16
18
19
20
21
COMP
RDSCK
RDSDATA
RDSLOCK
RDSHSLK
DO
CE1
CK
10 DI
5SL
6CE2
7WC
PDI
PCE1
PCK
PDO
PCE2
WC
9
8
3
4
17
13
22
FMANT
Y102
14
AUD8.4
VDD3.3
AC5
VCC
VDD3.3
DIVER
ROMVDD
16 COMP
DO
CE1
CK
10 DI
5SL
6CE2
SPDI
SPCE1
SPCK
SPDO
SSL
SPCE2
D105
Q114
Q115
Q105
Q119 21
AMP 7
5
IC102
NJM2068V
Q116
Q117
SCOMP
MCOMP
SCPON
COMPP
COM
P
MCPON
AMPW
(2/2)
A
TUL
11 LDET LDET
RCK
RDSDT
RDSLK
RHSLK
A
Q124
Q109
Q110
Q108
4
1,5
3
2
AMAIN UNIT (1/2)
18
19
20
21
RDSCK
RDSDATA
RDSLOCK
RDSHSLK
11 LDET MBP1
SRCK
SRDSDT
SRDSLK
SRHSLK
Q125
Q126
Q123
B
A
FM/AM TUNER UNIT FM/AM TUNER UNIT
JSE
N

FX-MG8667DVZT/EW 17
5678
5678
C
D
F
A
B
E
IC502(1/2)
PEG164A
SYSTEM
MICROCOMPUTER
62
5
COM-
COM+ 4
CN303(1/2)
11
12
15
16
118
115
119
117
116
126
128
9
10
30
8
29
63
3
7
5
4
61
60
SPDI
SPCE1
SPCK
SPDO
SSL
25
59
57
58
55
SRCK
SRDSDT
SRDSLK
SRHSLK
MBP1
23
52
53
54
24
RCK RCK
RDSDT
RDSLK
RHSLK
LDET [LDET]
SPCE2
SPDI
SPCE1
[SPCK]
SPDO
SSL
SL
[SPCE2]
AMSUB/SRCK
COMPP
COMPN
SCOMPON
SCPON
MCOMPON
SBP1/SRDSLK
SBP2/SRHSLK
MBP1/[SLDET]
MBP2/SRDSDT
(2/2)
A
1
2
16
3
4
5
6
7
8
9
10
11
14
15
ACC+B ACC+B
ENCVOL+
ENCVOL-
ACC9V
ACC9V
AC5V ICVDD
ENCAUD+
ENCAUD-
ENC1P
ENC1N
ENC2P
ENC2N
ENC1P
ENC1N
ENC2P
ENC2N
ENC1P
ENC1M
ENC2P
ENC2M
LCDDO
LCDCK
LCDCE
LCDDI
LDTI
LCK
LCE
LDTO
PWMBL
PINFO
LDTI
LCK
LCE
LDTO
PWMBL
PINFO
LDTI
LCK
LCE
LDTO
PWMBL
PINFO
PWMBL
P-INFO
CN408
31 PWMILL
PWMILL
PWMILL PWMILL
PDI
PCE1
PCK
PDO
PCE2
WC
PDI
PCE1
[PCK]
PDO
[PCE2]
4
3
1
2
5
6
9
10
12
13
14
15
16
17
18
19
20
11
8
7
CN303
B
CN802
MAINFIX
6
83 WC
SHVSEN/RDSLK
SHBSEN/RDSDT
SHVCONT/RHSLK
C
(2/2)
A
C
STBY
PLAY
MTL
LOAD
5
1
4
2
1
4
6
12
8
MS
PLAY
MTL
STBY2
104
22
9
IDECK UNIT
IC251
HA12216F
IC351
BA6923FP
EQ AMP
MECHANISM
DRIVER
CN251
CN252
CN254
CN255
CN253
6
15 MS
Lch
1412
FWD
L-ch
REV
L-ch
CN404
37
38
39
28
315 6
452
CN256 315 6
S101
LOAD
S102
MODE
Q101
REEL
SENSE
M
M
M2
SUB
MOTOR
M1
MAIN
MOTOR
5
2
1
JSENSOR UNIT
S103
70µs
4
4
4612 8229
CSLOAD

FX-MG8667DVZT/EW
18
1234
1234
C
D
F
A
B
E
IC502(2/2)
PEG164A
SYSTEM
MICROCOMPUTER
SWVDD
DDCONF2
SYSPW
SSW1
SSW2
ACCON
ADIMIN
BSEN
ASEN
77
76
78
79
95
123
82
86
81
121
AMPW
AMPW
FMPW
SWVDD
DDCONF2
SYSPW
STSW1
STSW2
ACCON
ADIM
[BSEN[
[ASEN]
AMPW
FMPW
67
68
122
80
69
98
97
8.4V REGULATOR
SWVDD
Q702
Q701
BU
BU2
AUD+B
2
6
1
13
14
4
7
AMP
IC202
NJM2068V AMP
6IC203
NJM4580V
AMP
5IC205
NJM2068V
6
TUL1
Q201
CDL1
VAL1
CDL1
Q402 Q401
AMUTE
MUTE
VAL1
REMT
FRMT
RMUT1
LMUT1
REMUTE
FRMUTE
RSEMUTE
LANMUTE
(1/2)
A
UTX
SHASEN/WAKEUP
CTS/IRQPW
URX
NC
42
51
45
HSTCMD
WAKE UP MG
ANALOUT
CN407
CN403
Q801
IRQPWR
VIDEO OUT
SLVSTS 43
47
2
12
CN1901
1
4
96
7
1
6
7
1
1
3
6
5
2
1
8
7
120
90
26
17
34
35
27
93
91
92
4
1
3
7
2
2
4
5
11
13
3
TX+
VAL
TX-
TXP
TXN
TXP
TXN
ADPG
NTSC
NTS1
NTS2
VV+
15 VDD3.3
SWVDD33
19
16
15
AMUTE
VDCONT
XRESET
VDCONT
RESET
VIDEO SELECTOR
IC801
NJM2235V
BUS DRIVER
IC301
HA12240FP
VIN1
VOUT
SW1 VSEL
STBN
DIN1
DOUT
AUXIN
RX2
[RESET]
RX1
TX
IPPW
VMUT1
VSEL1
VSEL2
VSEL
VMUTE1
VSEL1
VSEL2
SW2
VIN2
VIDEO FILTER
VIDEO FILTER
IC802
SM5304AV
VF
VOUT VIN
VIDEO SELECTOR
IC803
NJM2235V
VIN1
VOUT
SW1
SW2
VIN2
VIN3
IC804
SM5304AV
VF
VOUT VIN
RESET
CN1003
ISEN
[ISEN] ILLIN
ILL-
89
88
SELCK
SELCK SELDATA
SELDATA
AUD8.4
ANT+B SW
FMPW
AMPW
Q704
Q703
AMP+B SW
Q706
ACC+B SW
Q707
Q705
ANT+B
SYSPW
ACC+B
AMP+B
9V REGULATOR
Q710
Q709
ACC9V
10V REGULATOR
Q712
Q711
TU10V
BUS-
BUS+
VD8
VD5_ACC
VD5
SRVDD
VD8
VD5
VD5
SRVDD
29
31
24
27
22
23
A
(1/2)
A
E
C
XIN
20
18 XOUT
X501
10MHz
20
21
BVC33
VAL1
MAIN UNIT (2/2)
A
B
1Y 1A
3
24
1
2Y 2A
64
3Y 3A
89
INA OUTY
24
IC503
TC7SET08FUS1
3V -> 5V
IC504
TC74VHC08FTS1
5V -> 3V
IC401
TC7SET08FUS1
3V -> 5V
7
AMP
IC204
NJM2068V
6
(1/2)
A
C

FX-MG8667DVZT/EW 19
5678
5678
C
D
F
A
B
E
18
17
BU
AC5V
ILLIN
ISEN
AC5VMUTE
Q302
Q303
Q315
2
3
4
2
Q753
ACC
BU
ASEN
Q755
Q754
DDCONF2
IC752
S-812C56AUA-C3K
IC751
S-80940CNNB-G9A
VDCONT
Q601
Q603
2
1
TPS54350PWP
IC604
PH2
LSG
COMPV
SENSE
PH1 VIN1
VIN2
RT
Q607
Q608
1,2
4
BA00BC0WFP
IC603
3.3V REGULATOR
15
13
14
9
8
9
8
Q613
VD5
BU
2
3
S-812C39AMC-C2T
IC753
A
TOR
SWVDD
Q702
BU
RESET
Q752
Q751
BU1
5
Q606
Q604 Q610
Q605
ATX-
1
12
3
2
13
2
4
3
1
2
5
20
15
5
6
9
10
12
11
8
7
ILL+
ANT
12
ILL-
ILLP
ILLN
Q301
Q314
ATX+
TXN
TXP
ACC 7
11
MUTE
L- 9
19
L+
B
+B
1
MUTE
11
ACC
9
TXM+
10
TXM-
TXP
TXN
CN302
CN301
CN301
R-L-
AMP+B 3
AMP
CDL+
CDL-
19
RMUT/AUXI
ADIM
7
20
8
CN303(3/3)
CN303(2/3)
GND 10
SLD 17
SLD2
R-L+/ALI
21
1
AMP
AMP AMP
AMP
IC211
NJM2068V
Q384 Q389
14
18
23 SELCK
SELDATA
22
RLP(ALI)
RNL
LP
LN
2
1
1
IC209
OPA2134UA
Q383 Q386
2IC210
NJM2068V
2IC208
OPA2134UA
71
3
96
7
AMP
AUDIO SELECT
6IC203
NJM4580V
IC207
BD3842FS
7
AMP
5IC205
NJM2068V
5
AMP
7
5IC201
NJM2068V
REMT
BMUT
INA1
INB1
INE1 INC1
DA
CL
TUL
CDL
AUXL
L
1
L1 LANL
OUT1
RECA1
AC5V
Q381
Q382
FRMT
9
TX+
10
TX-
TXP
TXN
AUD+B
BU
Q602
VDCONT
Q614
Q609
VD8
VDD5V
VD5_ACC
VDD3.3
VDD33
SWVDD
Q616
1
2
IC601
LSG
RT
15
13
14
Q612
VCC84
BU
5
Q615 Q617
Q618
Q611
AC5V
BU1
BU
VCC 5V DC-DC CONVERTOR
8.0V DC-DC CONVERTOR
FMPW
AMPW
SCPON
S
W
W
5
SYSPW
A
TOR
Q710 5V REGULATOR
5V REGULATOR
RESET
Q756
Q762
SWVDD
AC5V
AC5
SRVDD
SRVDD REGULATOR
A
TOR
Q712
4
3
1
2
5
6
9
10
12
13
14
15
16
17
18
19
20
11
8
7
CN303
4
3
1
2
5
6
9
10
8
7
CN302
4
3
1
2
5
6
9
10
8
7
CN303
PH2
PH1 VIN1
VIN2
COMPV
SENSE
TPS54350PWP
BSEN
ACCON
SSW1
SSW2
SW1
SW2
Q312
Q313
ADIMIN
Q309
Q310
Q311
Q308
RMUT1
LMUT1
(1/2)
C
A
12
13
14
15
16
17
18
19
20
11
12
13
14
15
16
17
18
19
20
11
ANT+B
ALN
ALP
IND1
77
MDCSL

FX-MG8667DVZT/EW
20
1234
1234
C
D
F
A
B
E
BUFFER
5
3
7
1
10
12
13
VAL
ADPG
VV+
VAL+
VA-
ADPG
VV+
VV-
CN1005
SWVDD33
SWVDD33
SWVDD33SWVDD33
CN1003
6
1
4
3
5
CN1002
CN1102
CN1104
CN1103
IECIN
CN1101
NTS1
NTS2
NTSC
NTS1
NTS2
NTSC
NTS1
NTS2
NTSC
NTS1
NTS2
NTSC
DOUT
8
7
5
3
8
7
5
3
65,7
7
1
8
1 1
IC1101
TC7W04FU
1
2
3
4
5
6
CN1004
7
5
3
1
8
6
2
4
CN1102
1
CN1101
D
C
E
CN1551
A
CN403
CONNECTOR1 PCB
CONNECTOR2 PCB
S993
EAUP
EAUN
1
2
16
3
5
6
7
8
9
10
11
12
14
15
1,2
7
8
1,2
7
66
8
99
10 10
12 12
ACC+B
ACC+B
LCD RST
ENCVOL+
ENCVOL-
IC-VDD
IC-VDD
ENCAUD+
ENCAUD-
KEY-DO
KEY-CLK
KEY-CE
KEI-DI
LDI
LCK
LCE
LDO
LDI
LCK
LCE
LDO
PWM-IND
PANEL-INFO
PWM-ILL
IC801
LC75804W
KEY CONTROL
CN802
CN801
CN803
CN980
KEY MATRIX
KEY MATRIX
ILLMINATION
ILLMINATION
ILLMINATION
Q819
Q820
Q823
Q824
Q826
Q815
ACC 13V
DO
CE
CLOK
DI
RSET
KD1
KD2
KD2
KST1
KD3
KD4
KD3
KD4
78
79
80
KST2
81
82
85
KST3
86
KST4
KST5
87
KST1
84
87
98
99
100
96
SEG,COM
ILLMINATION
83
KST6
B
ACC 13V
A
CN408
COILLG
COILLR
4
Q801-Q806
Q809-Q814
KEYBOARD PCB
G
L PCB
5
LCD
Q801-804
S980
EVUP
EVUN
1,2
7
8
1,2
7
55
8
99
10 10
12 12
CN990
KEY MATRIX
KD2
KST6
KD3
KD4
ILLMINATION
H
R PCB