Pioneer Super Tuner IIID DEH-P5800MP User manual

Multi-CD control High power CD/MP3/WMA player with RDS tuner
Operation Manual
DEH-P5800MP
Visit www.pioneer.co.uk (or www.pioneer-eur.com)
to register your product
ENGLISH
Qsound.vision.soul
MAN-DEH-P5800MP-GB.fm Page 1 Friday, September 30, 2005 3:15 PM

2
ENGLISH
Contents
Thank you for buying this Pioneer product
Please read through these operating instructions so you will know how to operate your
model properly. After you have finished reading the instructions, keep this manual in a
safe place for future reference.
Connecting the Units ........................... 3
Installation ............................................ 5
DIN Front/Rear-mount ................................ 5
DIN Front-mount ......................................... 5
*Installation with the rubber bush ........... 5
*Removing the Unit ................................ 5
DIN Rear-mount .......................................... 5
*Installation using the screw holes
on the side of the unit ........................... 5
Fixing the front panel .................................. 6
Before You Start ................................... 7
About this unit ............................................. 7
About this manual ....................................... 7
About the illumination color ......................... 7
In case of trouble ........................................ 7
Features ...................................................... 7
About MP3 .................................................. 8
About WMA ................................................. 8
Visit our website .......................................... 8
Use and care of the remote control ............. 8
*Installing the battery ............................. 8
*Using the remote control ...................... 8
Protecting your unit from theft ..................... 9
*Removing the front panel ..................... 9
*Attaching the front panel ....................... 9
What’s What .......................................... 9
Head unit ..................................................... 9
Remote control .......................................... 10
Power ON/OFF .................................... 10
Turning the unit on .................................... 10
Selecting a source .................................... 10
Turning the unit off .................................... 10
Tuner ................................................... 11
Listening to the radio ................................ 11
Introduction of advanced tuner
operation ................................................ 11
Storing and recalling broadcast
frequencies ............................................. 11
Tuning in strong signals ............................ 12
Storing the strongest broadcast
frequencies ............................................. 12
RDS ..................................................... 12
Introduction of RDS operation .................. 12
Switching the RDS display ........................ 12
Selecting alternative frequencies .............. 13
*Using PI Seek ..................................... 13
*Using Auto PI Seek for
preset stations .................................... 13
*Limiting stations to regional
programming ...................................... 13
Receiving traffic announcements .............. 13
Using news program interruption .............. 14
Receiving PTY alarm broadcasts ............. 14
PTY list ..................................................... 14
Built-in CD Player ............................... 15
Playing a CD ............................................. 15
Introduction of advanced built-in
CD player operation ............................... 15
Repeating play .......................................... 15
Playing tracks in random order ................. 16
Scanning tracks of a CD ........................... 16
Pausing CD playback ............................... 16
Using compression and BMX ................... 16
Selecting the search method .................... 16
Searching every 10 tracks in
the current disc ....................................... 17
Using disc title functions ........................... 17
*Entering disc titles .............................. 17
*Displaying disc titles ........................... 17
Using CD TEXT functions ......................... 17
*Displaying text information on
CD TEXT discs ................................... 17
*Scrolling text information
in the display ...................................... 17
MP3/WMA/WAV Player ....................... 18
Playing MP3/WMA/WAV ........................... 18
Introduction of advanced built-in
CD player (MP3/WMA/WAV)
operation ................................................ 19
Repeating play .......................................... 19
Playing tracks in random order ................. 19
Scanning folders and tracks ..................... 19
Pausing MP3/WMA/WAV playback .......... 20
Selecting the search method .................... 20
Searching every 10 tracks in the
current folder .......................................... 20
Using compression and BMX ................... 20
Displaying text information on
MP3/WMA disc ....................................... 20
Displaying text information on
WAV disc ................................................ 21
Scrolling text information in the display .... 21
Multi-CD Player ................................... 21
Playing a CD ............................................. 21
50-disc multi-CD player ............................ 21
Introduction of advanced multi-CD
player operation ..................................... 22
Repeating play .......................................... 22
Playing tracks in random order ................. 22
Scanning CDs and tracks ......................... 22
Pausing CD playback ............................... 23
Using ITS playlists .................................... 23
*Creating a playlist with ITS
programming ...................................... 23
*Playback from your ITS playlist .......... 23
*Erasing a track from your
ITS playlist .......................................... 23
*Erasing a CD from your ITS playlist ... 24
Using disc title functions ........................... 24
*Entering disc titles .............................. 24
*Displaying disc titles ........................... 24
Using CD TEXT functions ......................... 24
*Displaying text information on
CD TEXT discs ................................... 24
*Scrolling text information in
the display .......................................... 25
Using compression and bass emphasis ... 25
Audio Adjustments ............................ 25
Introduction of audio adjustments ............ 25
Compensating for equalizer curves
(EQ-EX) ................................................. 26
Using balance adjustment ........................ 26
Using the equalizer ................................... 26
*Recalling equalizer curves ................. 26
*Adjusting equalizer curves ................. 26
*Fine-adjusting equalizer curve ........... 27
Adjusting bass and treble ......................... 27
*Adjusting bass and treble level .......... 27
*Selecting bass frequency ................... 27
*Selecting treble frequency .................. 27
Adjusting loudness ................................... 28
Using subwoofer output ............................ 28
*Turning a subwoofer on/off ................ 28
*Adjusting subwoofer settings ............. 28
Using nonfading output ............................ 28
*Adjusting nonfading output level ........ 29
Using the high pass filter .......................... 29
Adjusting source levels ............................. 29
Initial Settings ..................................... 30
Adjusting initial settings ............................ 30
Setting the FM tuning step ....................... 30
Switching Auto PI Seek ............................ 30
Switching the warning tone ...................... 30
Switching the auxiliary setting .................. 30
Setting the rear output and
subwoofer controller ............................... 31
Other Functions .................................. 31
Switching the display illumination ............. 31
Switching the button illumination .............. 31
Using the AUX source .............................. 32
*Selecting AUX as the source ............. 32
*Setting the AUX title ........................... 32
Additional Information ....................... 32
Understanding built-in CD player
error messages ...................................... 32
Sound muting ........................................... 32
CD player and care .................................. 32
CD-R/CD-RW discs .................................. 33
MP3, WMA and WAV files ........................ 33
*MP3 additional information ................. 34
*WMA additional information ............... 34
*WAV additional information ................ 34
About folders and MP3/WMA/
WAV files ............................................... 34
Terms ....................................................... 35
Specifications ........................................... 36
MAN-DEH-P5800MP-GB.fm Page 2 Friday, September 30, 2005 3:15 PM

3
ENGLISH
Connecting the Units
Notes
•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in
a recreational vehicle, truck, or bus, check the battery voltage.
•To avoid shorts in the electrical system, be sure to disconnect the -battery cable before
beginning installation.
•Refer to the owner’s manual for details on connecting the power amp and other units, then
make connections correctly.
•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal parts.
•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift,
handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater
outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-
circuiting to the vehicle body.
•Don’t pass the yellow lead through a hole into the engine compartment to connect to the
battery. This will damage the lead insulation and cause a very dangerous short.
•Do not shorten any leads. If you do, the protection circuit may fail to work when it should.
•Never feed power to other equipment by cutting the insulation of the power supply lead of
the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing
overheating.
•When replacing the fuse, be sure to only use a fuse of the rating prescribed on this product.
•Since a unique BPTL circuit is employed, never wire so the speaker leads are directly
grounded or the left and right -speaker leads are common.
•Speakers connected to this unit must be highpower with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other
than those noted here may result in the speakers catching fire, emitting smoke or becoming
damaged.
•When this product’s source is switched ON, a control signal is output through the blue/white
lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna
relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect
to the antenna booster power supply terminal.
•When an external power amp is being used with this system, be sure not to connect the blue/
white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the
power terminal of the auto-antenna. Such connection could cause excessive current drain
and malfunction.
•To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the
unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not
insulated.
•To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the
output side is black. Connect the connectors of the same colors correctly.
•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the
ignition switch, the red lead of the unit should be connected to a terminal coupled with
ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained
when you are away from the vehicle for several hours.
•The black lead is ground. Please ground this lead separately from the ground of high-current
products such as power amps. ,
If you ground the products together and the ground becomes detached, there is a risk of
damage to the products or fire.
ACC position No ACC position
•Cords for this product and those for other products may be different colors even if they have
the same function. When connecting this product to another product, refer to the supplied
manuals of both products and connect cords that have the same function.
MAN-DEH-P5800MP-GB.fm Page 3 Friday, September 30, 2005 3:15 PM

4
ENGLISH
Connecting the Units
Note
Depending on the kind of vehicle, the
function of 3* and 5* may be different. In this
case, be sure to connect 2* to 5* and 4* to 3*.
Connect leads of the same
color to each other.
System remote control
Cap (1*)
When not using this
terminal, do not remove
the cap.
Yellow (3*)
Back-up (or accessory)
Yellow (2*)
To terminal always supplied with
power regardless of ignition switch
position.
Red (5*)
Accessory (or back-up)
Red (4*)
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Black (ground)
To vehicle (metal) body.
ISO connector
Note
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
Speaker leads
White: Front left +
White/black: Front left -
Gray: Front right +
Gray/black: Front right -
Green: Rear left + or Subwoofer +
Green/black: Rear left - or Subwoofer -
Violet: Rear right + or Subwoofer +
Violet/black: Rear right - or Subwoofer -
Blue/white (6*)
Blue/white (7*)
To Auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Power amp
(sold separately)
Jack for Wired Remote Control
Please see the Instruction Manual for the
Wired Remote Control (sold separately).
Subwoofer output or non
fading output
Antenna jack
Front
output
Connecting cords with RCA pin
plugs (sold separately)
This product
Left
Subwoofer
Blue/white
To system control terminal of the
power amp (max. 300 mA 12 V DC).
Right
Perform these connections when
using the optional amplifier.
Power amp
(sold separately)
IP-BUS cable
Mult-CD player
(sold separately)
IP-BUS input (Blue)
Subwoofer
Front speaker Front speaker
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
Note
Change the initial setting of this unit
(refer to the Operation Manual). The
subwoofer output of this unit is
monaural.
Yellow/black
If you use a cellular telephone, connect it via
the Audio Mute lead on the cellular telephone.
If not, keep the Audio Mute lead free of any
connections.
Fuse
MAN-DEH-P5800MP-GB.fm Page 4 Friday, September 30, 2005 3:15 PM

5
ENGLISH
Removing the Unit
To remove the frame, extend top and bottom of the frame outwards in order to unlock
it. (When reattaching the frame, point the side with a groove downwards and attach it.)
•It becomes easy to remove the frame if the front panel is released.
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame.
To remove the frame, extend top and bottom of the frame outwards in order to unlock
it. (When reattaching the frame, point the side with a groove downwards and attach it.)
•It becomes easy to remove the frame if the front panel is released.
Insert the supplied extraction keys into the unit, as shown
in the figure, until they click into place. Keeping the keys
pressed against the sides of the unit, pull the unit out.
Installation
Notes
•Before making a final installation of the unit, temporarily connect the wiring to confirm that
the connections are correct and the system works properly.
•Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
•Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
•Install the unit where it does not get in the driver’s way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
•The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere
hot – for instance, near a heater outlet.
•If installation angle exceeds 60° from horizontal, the unit might not give its optimum
performance.
DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount)
or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of
unit chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush
60°
Holder
After inserting the holder into the dashboard, then select
the appropriate tabs according to the thickness of the
dashboard material and bend them.
(Install as firmly as possible using the top and bottom
tabs. To secure, bend the tabs 90 degrees.)
Rubber bush
Screw
Dashboard
MAN-DEH-P5800MP-GB.fm Page 5 Friday, September 30, 2005 3:15 PM

6
ENGLISH
Installation
2. Fastening the unit to the factory radio mounting bracket.
Fixing the front panel
If you do not operate the Removing and Attaching the Front Panel Function, use the
supplied fixing screws and fix the front panel to this unit.
1. Attach the holders to both
sides of the front panel.
Select a position where the screw holes of the bracket
and the screw holes of the head unit become aligned
(are fitted) and tighten the screws at 2 places on each
side. Use either truss screws (5 x8 mm) or flush
surface screws (5 x9 mm), depending on the shape of
the screw holes in the bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
Holder
2. Replace the front panel to the
unit.
3. Flip the holders into upright
positions.
4. Fix the front panel to the unit
using fixing screws.
Fixing screw
MAN-DEH-P5800MP-GB.fm Page 6 Friday, September 30, 2005 3:15 PM

7
ENGLISH
Before You Start
Private households in the 25 member states of the EU, in Switzerland and Norway
may return their used electronic products free of charge to designated collection
facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct
method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary
treatment, recovery and recycling and thus prevent potential negative effects on the
environment and human health.
About this unit
The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the
Middle East, Africa and Oceania. Use in other areas may result in poor reception. The
RDS (radio data system) function operates only in areas with FM stations broadcasting
RDS signals.
!CAUTION
Do not allow this unit to come into contact with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat could result from contact with liquids.
•This product contains a laser diode of higher class than 1. To ensure continued
safety, do not remove any covers or attempt to gain access to the inside of the
product. Refer all servicing to qualified personnel.
A CLASS 1 LASER PRODUCT label is affixed to the
bottom of this unit.
•The Pioneer CarStereo-Pass is for use only in
Germany.
•Keep this manual handy as a reference for operating
procedures and precautions.
•Always keep the volume low enough so that you can hear sounds from outside the
vehicle.
•Protect this unit from moisture.
•If the battery is disconnected or discharged, the preset memory will be erased and
must be reprogrammed.
If you want to dispose this product, do not mix it with general household
waste. There is a separate collection system for used electronic
products in accordance with legislation that requires proper treatment,
recovery and recycling.
About this manual
This unit features a number of sophisticated functions ensuring superior reception and
operation. All the functions have been designed for the easiest possible use, but many
are not self-explanatory. This operation manual will help you benefit fully from this
unit’s potential and to maximize your listening enjoyment.
We recommend that you familiarize yourself with the functions and their operation by
reading through the manual before you begin using this unit. It is especially important
that you read and observe WARNINGs and CAUTIONs in this manual.
About the illumination color
This unit features multi-color illumination.
When the unit is turned on, the buttons and display illuminate in rainbow colors. To
select a particular illumination color, see “Switching the display illumination” on page
31.
In case of trouble
Should this product fail to operate properly, contact your dealer or nearest authorized
Pioneer Service Station.
Features
CD playback
Music CD/CD-R/CD-RW playback is possible.
MP3 file playback
You can play back MP3 files recorded on CD-ROM/CD-R/CD-RW (ISO9660 Level 1/
Level 2 standard recordings).
WMA file playback
You can play back WMA files recorded on CD-ROM/CD-R/CD-RW (ISO9660 Level 1/
Level 2 standard recordings).
WAV file playback
You can play back WAV files recorded on CD-ROM/CD-R/CD-RW (Linear PCM
(LPCM)/MS ADPCM recordings).
MAN-DEH-P5800MP-GB.fm Page 7 Friday, September 30, 2005 3:15 PM

8
ENGLISH
Before You Start
About MP3
Supply of this product only conveys a license for private, non-commercial use and
does not convey a license nor imply any right to use this product in any commercial
(i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any
other media), broadcasting/streaming via internet, intranets and/or other networks or
in other electronic content distribution systems, such as pay-audio or audio-on-
demand applications. An independent license for such use is required. For details,
please visit http://www.mp3licensing.com.
About WMA
The Windows Media™ logo printed on the box indicates that
this unit can play back WMA data.
WMA is short for Windows Media™ Audio and refers to an
audio compression technology that is developed by
Microsoft Corporation. WMA data can be encoded by using
Windows Media Player version 7 or later.
Windows Media and the Windows logo are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Notes
•This unit may not operate correctly depending on the application used to encode WMA files.
•Depending on the version of Windows Media Player used to encode WMA files, album
names and other text information may not be correctly displayed.
•There may be a slight delay when starting playback of WMA files encoded with image data.
Visit our website
Visit us at the following site:
•Register your product. We will keep the details of your purchase on file to help you
refer to this information in the event of an insurance claim such as loss or theft.
•We offer the latest information about Pioneer Corporation on our website.
Use and care of the remote control
Installing the battery
Slide the tray out on the back of the remote control and insert the battery with the plus
(+) and minus (–) poles pointing in the proper direction.
!WARNING
Keep the battery out of the reach of children. Should the battery be swallowed,
immediately consult a doctor.
!CAUTION
•Use only one CR2025 (3 V) lithium battery.
•Remove the battery if the remote control is not used for a month or longer.
•Do not recharge, disassemble, heat or dispose of the battery in fire.
•Do not handle the battery with metallic tools.
•Do not store the battery with metallic materials.
•In the event of battery leakage, wipe the remote control completely clean and install
a new battery.
•When disposing of used batteries, please comply with governmental regulations or
environmental public institutions’ rules that apply in your country/area.
Using the remote control
Point the remote control in the direction of the front panel to operate.
Important
•Do not store the remote control in high temperatures or direct sunlight.
•The remote control may not function properly in direct sunlight.
•Do not let the remote control fall onto the floor, where it may become jammed under
the brake or accelerator pedal.
MAN-DEH-P5800MP-GB.fm Page 8 Friday, September 30, 2005 3:15 PM

9
ENGLISH
Before You Start
Protecting your unit from theft
The front panel can be detached from the head unit and stored in the provided
protective case to prevent theft.
•If the front panel is not detached from the head unit within five seconds of turning off
the ignition, a warning tone will sound.
•You can turn off the warning tone. See “Switching the warning tone” on page 30.
Important
•Never use force or grip the display and the buttons too tightly when removing or
attaching.
•Avoid subjecting the front panel to excessive shocks.
•Keep the front panel out of direct sunlight and high temperatures.
Removing the front panel
1. Press OPEN to open the front panel.
2. Grip the left side of the front panel and pull it gently outward.
Take care not to grip it too tightly or to drop the front panel and protect it from contact
with water or other fluids to prevent permanent damage.
3. Put the front panel into provided protective case for safe keeping.
Attaching the front panel
*Replace the front panel by holding it upright to the unit and clipping it securely
into the mounting hooks.
What’s What
Head unit
햲TA button
Press to turn traffic announcements
function on or off.
Press and hold to turn NEWS
function on or off.
햳EQ button
Press to select various equalizer
curves.
햴FUNCTION button
Press to select functions.
햵OPEN button
Press to open the front panel.
햶8/2/4/6 buttons
Press to perform manual seek
tuning, fast forward, reverse and
track search controls. Also used for
controlling functions.
햷SW button
Press to directly select subwoofer
setting menu. See “Using subwoofer
output” on page 28. Press and hold
to select EQ-EX setting menu. See
“Compensating for equalizer curves
(EQ-EX)” on page 26.
햸AUDIO button
Press to select various sound quality
controls.
햹BAND button
Press to select among three FM
bands and MW/LW bands and to
cancel the control mode of functions.
햺1–6 buttons
Press for preset tuning and disc
number search when using a multi-
CD player.
햻SOURCE button
This unit is turned on by selecting a
source. Press to cycle through all the
available sources.
햽ILLUMINATION button
Press to change the button
illumination and the display
illumination.
햾DISPLAY button
Press to select different displays.
햿VOLUME
When you press VOLUME, it extends
outward so that it becomes easier to
turn. To retract VOLUME, press it
again. Rotate it to increase or
decrease the volume.
MAN-DEH-P5800MP-GB.fm Page 9 Friday, September 30, 2005 3:15 PM

10
ENGLISH
What’s What
Remote control
Operation is the same as when using the buttons on the head unit. See the explanation
of the head unit about the operation of each button with the exception of ATT, which
is explained below.
헀PAUSE button
Press to turn pause on or off.
헁CD button
Press to select the built-in or multi-CD player as the source.
헂TUNER button
Press to select the tuner as the source.
헃ATT button
Press to quickly lower the volume level, by about 90%. Press once more
to return to the original volume level.
헄VOLUME button
Press to increase or decrease the volume.
Power ON/OFF
Turning the unit on
*Press SOURCE to turn the unit on.
When you select a source, the unit is turned on.
Selecting a source
You can select a source you want to listen to. To switch to the built-in CD player, load
a disc in the unit (refer to page 15).
1. When using the head unit, press SOURCE to select a source.
Press SOURCE repeatedly to switch between the following sources:
Built-in CD player – Television – Tuner – Multi-CD player – External unit 1 –
External unit 2 – AUX
2. When using the remote control, press TUNER or CD to select a source.
Press each button repeatedly to switch between the following sources:
TUNER: Tuner – Television – Sources off
CD: Built-in CD player – Multi-CD player – Sources off
Notes
•In the following cases, the sound source will not change:
– When there is no unit corresponding to the selected source connected to this unit.
– When there is no disc in the unit.
– When there is no magazine in the multi-CD player.
– When the AUX (auxiliary input) is set to off (refer to page 30).
•External unit refers to a Pioneer product (such as one available in the future) that, although
incompatible as a source, enables control of basic functions by this unit. Two external units
can be controlled by this unit. When two external units are connected, the allocation of them
to external unit 1 or external unit 2 is automatically set by this unit.
•When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the
antenna, turn the source off.
Turning the unit off
*Press SOURCE and hold until the unit turns off.
MAN-DEH-P5800MP-GB.fm Page 10 Friday, September 30, 2005 3:15 PM

11
ENGLISH
Tuner
Listening to the radio
These are the basic steps necessary to operate the radio. More advanced tuner
operation is explained starting on this page.
This unit’s AF (alternative frequencies search) function can be turned on and off. AF
should be off for normal tuning operation (refer to page 13).
1. Press SOURCE to select the tuner.
Press SOURCE until tuner is selected as the source.
2. Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
3. Press BAND to select a band.
Press BAND until the desired band is displayed, F1, F2, F3 for FM or MW/LW.
4. To perform manual tuning, briefly press 4or 6.
The frequencies move up or down step by step.
5. To perform seek tuning, press and hold 4or 6for about one second and
release.
The tuner will scan the frequencies until a broadcast strong enough for good reception
is found.
•You can cancel seek tuning by briefly pressing 4or 6.
•If you press and hold 4or 6you can skip stations. Seek tuning starts as soon as
you release the button.
Note
•When the frequency selected is being broadcast in stereo the stereo (%) indicator will light.
햲Band indicator
Shows which band the radio is
tuned to, MW/LW or FM.
햳Frequency indicator
Shows the frequency to which the
tuner is tuned.
햴Stereo (%) indicator
Shows when the selected
frequency is being broadcast in
stereo.
햵Preset number indicator
Shows which preset has been
selected.
Introduction of advanced tuner operation
*Press FUNCTION to display the function names.
Press FUNCTION repeatedly to switch between the following functions:
BSM (best stations memory) – REG (regional) – LOCAL (local seek tuning) – TA
(traffic announcement standby) – AF (alternative frequencies search) – NEWS (news
program interruption)
•To return to the frequency display, press BAND.
•If MW/LW band is selected, you can only select BSM or LOCAL.
Note
•If you do not operate the function within about 30 seconds, the display is automatically
returned to the frequency display.
Storing and recalling broadcast frequencies
If you press any of the preset tuning buttons 1–6you can easily store up to six
broadcast frequencies for later recall with the touch of a button.
*When you find a frequency that you want to store in memory, press one of preset
tuning buttons 1–6 and hold until the preset number stops flashing.
The number you have pressed will flash in the preset number indicator and then
remain lit. The selected radio station frequency has been stored in memory.
The next time you press the same preset tuning button the radio station frequency is
recalled from memory.
Notes
•Up to 18 FM stations, six for each of the three FM bands, and six MW/LW stations can be
stored in memory.
•You can also use 8and 2to recall radio station frequencies assigned to preset tuning
buttons 1–6.
햲Function display
Shows the function status.
햳LOC indicator
Shows when local seek tuning is
on.
햴Preset number indicator
Shows which preset has been
selected.
MAN-DEH-P5800MP-GB.fm Page 11 Friday, September 30, 2005 3:15 PM

12
ENGLISH
Tuner
Tuning in strong signals
Local seek tuning lets you tune in only those radio stations with sufficiently strong
signals for good reception.
1. Press FUNCTION to select LOCAL.
Press FUNCTION until LOCAL appears in the display.
2. Press 8to turn local seek tuning on.
Local seek sensitivity (e.g., LOCAL 2) appears in the display.
3. Press 4or 6to set the sensitivity.
There are four levels of sensitivity for FM and two levels for MW/LW:
FM: LOCAL 1 – LOCAL 2 – LOCAL 3 – LOCAL 4
MW/LW: LOCAL 1 – LOCAL 2
The LOCAL 4 setting allows reception of only the strongest stations, while lower
settings let you receive progressively weaker stations.
4. When you want to return to normal seek tuning, press 2to turn local seek tuning
off.
LOCAL:OFF appears in the display.
Storing the strongest broadcast frequencies
BSM (best stations memory) lets you automatically store the six strongest broadcast
frequencies under preset tuning buttons 1–6. Once stored you can tune in to those
frequencies with the touch of button.
1. Press FUNCTION to select BSM.
Press FUNCTION until BSM appears in the display.
2. Press 8to turn BSM on.
BSM begins to flash. While BSM is flashing the six strongest broadcast frequencies
will be stored under preset tuning buttons 1–6in the order of their signal strength.
When finished, BSM stops flashing.
•To cancel the storage process, press 2.
Note
•Storing broadcast frequencies with BSM may replace broadcast frequencies you have
saved using buttons 1–6.
RDS
Introduction of RDS operation
RDS (radio data system) is a system for providing information along with FM
broadcasts. This inaudible information provides such features as program service
name, program type, traffic announcement standby and automatic tuning, and is
intended to aid radio listeners in finding and tuning in to a desired station.
*Press FUNCTION to display the function names.
Press FUNCTION repeatedly to switch between the following functions:
BSM (best stations memory) – REG (regional) – LOCAL (local seek tuning) – TA
(traffic announcement standby) – AF (alternative frequencies search) – NEWS (news
program interruption)
•To return to the frequency display, press BAND.
•If MW/LW band is selected, you can only select BSM or LOCAL.
Notes
•If you do not operate the function within about 30 seconds, the display is automatically
returned to the frequency display.
•RDS service may not be provided by all stations.
•RDS functions such as AF and TA are only active when your radio is tuned to an RDS
station.
Switching the RDS display
When you tune in an RDS station its program service name is displayed. Switch the
display to find out the frequency.
*Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
Program service name – PTY information – Frequency
PTY (program type ID code) information is listed on page 14.
햲TP ( ) indicator
Shows when a TP station is tuned
in.
햳News ( ) indicator
Shows when the set news program
is received.
햴Program service name
Shows the name of broadcast
program.
MAN-DEH-P5800MP-GB.fm Page 12 Friday, September 30, 2005 3:15 PM

13
ENGLISH
RDS
•PTY information and the frequency of the current station appears on the display for
eight seconds.
•If a PTY code of zero is received from a station or the signal is too weak for this unit
to pick up the PTY code, you cannot switch to PTY information display.
Selecting alternative frequencies
If you are listening to a broadcast and the reception becomes weak or there are other
problems, the unit will automatically search for a different station in the same network
which is broadcasting a stronger signal.
•The default setting for AF is off.
1. Press FUNCTION to select AF.
Press FUNCTION until AF appears in the display.
2. Press 8to turn AF on.
Press 8and AF :ON is displayed.
3. Press 2to turn AF off.
Press 2and AF :OFF is displayed.
Notes
•Only RDS stations are tuned in during seek tuning or BSM when AF is on.
•When you recall a preset station, the tuner may update the preset station with a new
frequency from the station’s AF list. (This is only available when using presets on the F1 or
F2 bands.) No preset number appears on the display if the RDS data for the station received
differs from that for the originally stored station.
•Sound may be temporarily interrupted by another program during an AF frequency search.
•AF can be turned on or off independently for each FM band.
Using PI Seek
If the unit fails to find a suitable alternative frequency, or if you are listening to a
broadcast and the reception becomes weak, the unit will automatically search for a
different station with the same programming. During the search, PI SEEK is displayed
and the output is muted. The muting is discontinued after completion of the PI Seek,
whether or not a different station is found.
Using Auto PI Seek for preset stations
When preset stations cannot be recalled, as when travelling long distances, the unit
can be set to perform PI Seek during preset recall.
•The default setting for Auto PI Seek is off. See “Switching Auto PI Seek” on page 30.
Limiting stations to regional programming
When AF is used to automatically retune frequencies, the regional function limits the
selection to stations broadcasting regional programs.
1. Press FUNCTION to select REG.
Press FUNCTION until REG appears in the display.
2. Press 8to turn the regional function on.
Press 8and REG :ON is displayed.
3. Press 2to turn the regional function off.
Press 2and REG :OFF is displayed.
Notes
•Regional programming and regional networks are organized differently depending on the
country (i.e., they may change according to the hour, state or broadcast area).
•The preset number may disappear on the display if the tuner tunes in a regional station
which differs from the originally set station.
•The regional function can be turned on or off independently for each FM band.
Receiving traffic announcements
TA (traffic announcement standby) lets you receive traffic announcements
automatically, no matter what source you are listening to. TA can be activated for both
a TP station (a station that broadcasts traffic information) or an enhanced other
network’s TP station (a station carrying information which cross-references TP
stations).
1. Tune in a TP or enhanced other network’s TP station.
When you are tuned into a TP or enhanced other network’s TP station the TP ( )
indicator will light.
2. Press TA to turn traffic announcement standby on.
Press TA and TA ON appears in the display. The tuner will stand-by for traffic
announcements.
•To turn traffic announcements standby off, press TA again.
3. Use VOLUME to adjust the TA volume when a traffic announcement begins.
Rotate it to increase or decrease the volume.
The newly set volume is stored in memory and recalled for subsequent traffic
announcements.
MAN-DEH-P5800MP-GB.fm Page 13 Friday, September 30, 2005 3:15 PM

14
ENGLISH
RDS
4. Press TA while a traffic announcement is being received to cancel the
announcement.
The tuner returns to the original source but remains in the standby mode until TA is
pressed again.
•You can also cancel the announcement by pressing SOURCE, BAND, 8, 2, 4or
6while a traffic announcement is being received.
Notes
•You can also turn the TA function on or off in the menu that appears with the pressing of
FUNCTION.
•The system switches back to the original source following traffic announcement reception.
•Only TP and enhanced other network’s TP stations are tuned in during seek tuning or BSM
when TA is on.
Using news program interruption
When a news program is broadcast from a PTY code news station, the unit can switch
from any station to the news broadcast station. When the news program ends,
reception of the previous program resumes.
*Press TA and hold to turn on news program interruption.
Press TA until NEWS ON appears in the display.
•To turn off news program interruption, press TA and hold until NEWS OFF appears
in the display.
•A news program can be canceled by pressing TA.
•You can also cancel the news program by pressing SOURCE, BAND, 8, 2, 4or 6
while a news program is being received.
Note
•You can also turn on or off news program in the menu that appears with the pressing of
FUNCTION.
Receiving PTY alarm broadcasts
PTY alarm is a special PTY code for announcements regarding emergencies such as
natural disasters. When the tuner receives the radio alarm code, ALARM appears on
the display and the volume adjusts to the TA volume. When the station stops
broadcasting the emergency announcement, the system returns to the previous
source.
•An emergency announcement can be canceled by pressing TA.
•You can also cancel an emergency announcement by pressing SOURCE, BAND,
8, 2, 4or 6.
PTY list
Specific Type of program
NEWS News
AFFAIRS Current affairs
INFO General information and advice
SPORT Sports
WEATHER Weather reports/meteorological information
FINANCE Stock market reports, commerce, trading, etc.
POP MUS Popular music
ROCK MUS Contemporary modern music
EASY MUS Easy listening music
OTH MUS Non-categorized music
JAZZ Jazz
COUNTRY Country music
NAT MUS National music
OLDIES Oldies, golden oldies
FOLK MUS Folk music
L. CLASS Light classical music
CLASSIC Classical music
EDUCATE Educational programs
DRAMA Radio plays and serials
CULTURE National or regional culture
SCIENCE Nature, science and technology
VARIED Light entertainment
CHILDREN Children’s
SOCIAL Social affairs
RELIGION Religious affairs or services
PHONE IN Phone in
TOURING Travel programs; not for traffic announcements
LEISURE Hobbies and recreational activities
DOCUMENT Documentaries
MAN-DEH-P5800MP-GB.fm Page 14 Friday, September 30, 2005 3:15 PM

15
ENGLISH
Built-in CD Player
Playing a CD
These are the basic steps necessary to play a CD with your built-in CD player. More
advanced CD operation is explained starting on this page.
1. Press OPEN to open the front panel.
CD loading slot appears.
•After a CD has been inserted, press SOURCE to select the built-in CD player.
2. Insert a CD into the CD loading slot.
Playback will automatically start.
•You can eject a CD by pressing EJECT.
•To avoid a malfunction, make sure that no
metal object comes into contact with the
terminals when the front panel is open.
3. Close the front panel.
4. Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
5. To perform fast forward or reverse, press and hold 4or 6.
•If you select ROUGH, pressing and holding 4or 6enables you to search every 10
tracks in the current disc. (Refer to “Selecting the search method” on page 16.)
6. To skip back or forward to another track, press 4or 6.
Pressing 6skips to the start of the next track. Pressing 4once skips to the start of the
current track. Pressing again will skip to the previous track.
Notes
•The built-in CD player plays one standard, 12-cm or 8-cm CD at a time. Do not use an
adapter when playing 8-cm CDs.
•Do not insert anything other than a CD into the CD loading slot.
•If you cannot insert a disc completely or if after you insert a disc the disc does not play, check
that the label side of the disc is up. Press EJECT to eject the disc, and check the disc for
damage before inserting it again.
•If an error message such as ERROR-11 is displayed, refer to “Understanding built-in CD
player error messages” on page 32.
•When a CD TEXT disc is inserted, the disc and track titles begin to scroll to the left
automatically.
햲Play time indicator
Shows the elapsed playing time of
the current track.
햳Track number indicator
Shows the track currently playing.
CD loading slot
EJECT button
Introduction of advanced built-in CD player operation
*Press FUNCTION to display the
function names.
Press FUNCTION repeatedly to switch between the following functions:
RPT (repeat play) – RDM (random play) – SCAN (scan play) – PAUSE (pause) –
COMP (compression and BMX) – FF/REV (search method)
•To return to the playback display, press BAND.
Note
•If you do not operate the function within about 30 seconds, the display is automatically
returned to the playback display.
Repeating play
Repeat play lets you hear the same track or disc over again.
1. Press FUNCTION to select RPT.
Press FUNCTION until RPT appears in the display.
2. Press 4or 6to select the repeat range.
This switches you to the selected setting.
• RPT:DSC – Repeat the current disc
•RPT:TRK– Repeat just the current track
Note
•If you perform track search or fast forward/reverse during TRK, the repeat play range
changes to DSC.
햲Function display
Shows the function status.
햳RPT indicator
Shows when repeat play is turned
on.
MAN-DEH-P5800MP-GB.fm Page 15 Friday, September 30, 2005 3:15 PM

16
ENGLISH
Built-in CD Player
Playing tracks in random order
Random play lets you play back tracks on the CD in a random order.
1. Press FUNCTION to select RDM.
Press FUNCTION until RDM appears in the display.
2. Press 8to turn random play on.
RDM :ON appears in the display. Tracks will play in a random order.
3. Press 2to turn random play off.
RDM :OFF appears in the display. Tracks will continue to play in order.
Scanning tracks of a CD
Scan play lets you hear the first 10 seconds of each track on the CD.
1. Press FUNCTION to select SCAN.
Press FUNCTION until SCAN appears in the display.
2. Press 8to turn scan play on.
SCAN :ON appears in the display. The first 10 seconds of each track is played.
3. When you find the desired track press 2to turn scan play off.
SCAN :OFF appears in the display. The track will continue to play.
•If the display has automatically returned to the playback display, select SCAN again
by pressing FUNCTION.
Note
•After scanning of a CD is finished, normal playback of the tracks will begin again.
Pausing CD playback
Pause lets you temporarily stop playback of the CD.
1. Press FUNCTION to select PAUSE.
Press FUNCTION until PAUSE appears in the display.
2. Press 8to turn pause on.
PAUSE:ON appears in the display. Play of the current track pauses.
3. Press 2to turn pause off.
PAUSE:OFF appears in the display. Play will resume at the same point that you turned
pause on.
Note
•You can also turn pause on or off by pressing PAUSE.
Using compression and BMX
Using the COMP (compression) and BMX functions let you adjust the sound playback
quality of this player. Each of the functions has a two-step adjustment. The COMP
function balances the output of louder and softer sounds at higher volumes. BMX
controls sound reverberations to give playback a fuller sound. Listen to each of the
effects as you select through them and use the one that best enhances the playback
of the track or CD that you are listening to.
1. Press FUNCTION to select COMP.
Press FUNCTION until COMP appears in the display.
2. Press 8or 2to select your favorite setting.
Press 8or 2repeatedly to switch between the following settings:
COMP OFF – COMP 1 – COMP 2 – COMP OFF – BMX 1 – BMX 2
Selecting the search method
You can switch the search method between fast forward/reverse and searching every
10 tracks.
1. Press FUNCTION to select FF/REV.
Press FUNCTION until FF/REV appears in the display.
•If the search method ROUGH has been previously selected, ROUGH will be
displayed.
2. Press 4or 6to select the search method.
Press 4or 6until the desired search method appears in the display.
•FF/REV– Fast forward and reverse
• ROUGH – Searching every 10 tracks
MAN-DEH-P5800MP-GB.fm Page 16 Friday, September 30, 2005 3:15 PM

17
ENGLISH
Built-in CD Player
Searching every 10 tracks in the current disc
If a disc contains over 10 tracks, you can search every 10 tracks. When a disc contains
many tracks, you can roughly search for the track you want to play.
1. Select the search method ROUGH.
Refer to “Selecting the search method” on page 16.
2. Press and hold 4or 6to search every 10 tracks on a disc.
•If a disc contains less than 10 tracks, pressing and holding 6recalls the last track
of the disc. Also, if the remaining number of tracks after searching every 10 tracks
is less than 10, pressing and holding 6recalls the last track of the disc.
•If a disc contains less than 10 tracks, pressing and holding 4recalls the first track
of the disc. Also, if the remaining number of tracks after searching every 10 tracks
is less than 10, pressing and holding 4recalls the first track of the disc.
Using disc title functions
You can input CD titles and display the title. The next time you insert a CD for which
you have entered a title, the title of that CD will be displayed.
Entering disc titles
Use the disc title input feature to store up to 48 CD titles in the unit. Each title can be
up to 8 characters long.
1. Play the CD that you want to enter a title for.
2. Press FUNCTION and hold until TITLE IN appears in the display.
•When playing a CD TEXT disc, you cannot switch to TITLE IN. The disc title will
have already been recorded on a CD TEXT disc.
3. Press 8or 2to select a letter of the alphabet.
Each press of 8will display a letter of the
alphabet in A B C ... X Y Z, numbers and
symbols in 123...>[]order. Each press
of 2will display a letter in the reverse
order, such as Z Y X ... C B A order.
4. Press 6to move the cursor to the next character position.
When the letter you want is displayed, press 6to move the cursor to the next position
and then select the next letter. Press 4to move backwards in the display.
5. Move the cursor to the last position by pressing 6after entering the title.
When you press 6one more time, the entered title is stored in memory.
6. Press BAND to return to the playback display.
Notes
•Titles remain in memory, even after the disc has been removed from the unit, and are
recalled when the disc is reinserted.
•After data for 48 discs has been stored in memory, data for a new disc will overwrite the
oldest one.
•If you connect a multi-CD player, you can input disc titles for up to 100 discs.
Displaying disc titles
You can display the text information of any disc that has had a disc title entered.
*Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
Play time – DISC TTL (disc title)
When you select DISC TTL, the title of the currently playing disc is shown in the
display.
•If no title has been entered for the currently playing disc, NO D-TTL is displayed.
Using CD TEXT functions
Some discs have certain information encoded on the disc during manufacture. These
discs may contain such information as the CD title, track title, artist’s name and
playback time and are called CD TEXT discs. Only these specially encoded CD TEXT
discs support the functions listed below.
Displaying text information on CD TEXT discs
*Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
Play time – DISC TTL (disc title) – ART NAME (disc artist name) – TRK TTL (track
title) – ART NAME (track artist name)
•If specific information has not been recorded on a CD TEXT disc, NO XXXX will be
displayed (e.g., NO T-TTL).
Scrolling text information in the display
This unit can display the first 8 letters only of DISC TTL, ART NAME, TRK TTL and
ART NAME. When the recorded information is longer than 8 letters, you can scroll the
text to the left so that the rest of the title can be seen.
*Press DISPLAY and hold until the title begins to scroll to the left.
The rest of the title will appear in the display.
MAN-DEH-P5800MP-GB.fm Page 17 Friday, September 30, 2005 3:15 PM

18
ENGLISH
MP3/WMA/WAV Player
Playing MP3/WMA/WAV
These are the basic steps necessary to play an MP3/WMA/WAV with your built-in CD
player. More advanced MP3/WMA/WAV operation is explained starting on page 19.
1. Press OPEN to open the front panel.
CD loading slot appears.
•After a CD-ROM has been inserted, press SOURCE to select the built-in CD player.
2. Insert a CD-ROM into the CD loading slot.
Playback will automatically start.
•You can eject a CD-ROM by pressing EJECT.
•To avoid a malfunction, make sure that no
metal object comes into contact with the
terminals when the front panel is open.
3. Close the front panel.
4. Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
햲MP3 indicator
Shows when an MP3 file is playing.
햳WMA indicator
Shows when a WMA file is playing.
햴Track number indicator
Shows the track (file) currently
playing.
•If a track number 100 to 199 is
selected, 6on the left of the
track number indicator will light.
•If a track number 200 or more is
selected, 6on the left of the
track number indicator will blink.
햵Play time indicator
Shows the elapsed playing time of
the current track (file).
햶Folder number indicator
Shows the number of folder
currently playing.
CD loading slot
EJECT button
5. Press 8or 2to select a folder.
•You cannot select a folder that does not have an MP3/WMA/WAV file recorded in it.
•To return to folder 01 (ROOT), press and hold BAND. However, if folder 01 (ROOT)
contains no files, playback commences with folder 02.
6. To perform fast forward or reverse, press and hold 4or 6.
•This is fast forward and reverse operation only for the file being played. This
operation is canceled when the previous or next file is reached.
•If you select ROUGH, pressing and holding 4or 6enables you to search every 10
tracks in the current folder. (Refer to “Selecting the search method” on page 20.)
7. To skip back or forward to another track, press 4or 6.
Pressing 6skips to the start of the next track. Pressing 4once skips to the start of the
current track. Pressing again will skip to the previous track.
Notes
•When playing discs with MP3/WMA/WAV files and audio data (CD-DA) such as CD-EXTRA
and MIXED-MODE CDs, both types can be played only by switching mode between MP3/
WMA/WAV and CD-DA with BAND.
•If you have switched between playback of MP3/WMA/WAV files and audio data (CD-DA),
playback starts at the first track on the disc.
•The built-in CD player can play back an MP3/WMA/WAV file recorded on CD-ROM. (Refer
to page 33 for files that can be played back.)
•Do not insert anything other than a CD into the CD loading slot.
•There is sometimes a delay between starting up CD playback and the sound being issued.
When being read, FRMTREAD is displayed.
•If you cannot insert a disc completely or if after you insert a disc the disc does not play, check
that the label side of the disc is up. Press EJECT to eject the disc, and check the disc for
damage before inserting it again.
•Playback is carried out in order of file number. Folders are skipped if they contain no files.
(If folder 01 (ROOT) contains no files, playback commences with folder 02.)
•When playing back files recorded as VBR (variable bit rate) files, the play time will not be
correctly displayed if fast forward or reverse operations are used.
•If the inserted disc contains no files that can be played back, NO AUDIO is displayed.
•If the inserted disc contains WMA files that are protected by digital rights management
(DRM), SKIPPED is displayed while the protected file is skipped.
•If all the files on the inserted disc are secured by DRM, PROTECT is displayed.
•There is no sound on fast forward or reverse.
•If an error message such as ERROR-11 is displayed, refer to “Understanding built-in CD
player error messages” on page 32.
•When an MP3/WMA/WAV disc is inserted, folder name and file name begin to scroll to the
left automatically.
MAN-DEH-P5800MP-GB.fm Page 18 Friday, September 30, 2005 3:15 PM

19
ENGLISH
MP3/WMA/WAV Player
Introduction of advanced built-in CD player (MP3/WMA/
WAV) operation
*Press FUNCTION to display the function names.
Press FUNCTION repeatedly to switch between the following functions:
RPT (repeat play) – RDM (random play) – SCAN (scan play) – PAUSE (pause) –
COMP (compression and BMX) – FF/REV (search method)
•To return to the playback display, press BAND.
Note
•If you do not operate the function within about 30 seconds, the display is automatically
returned to the playback display.
Repeating play
For MP3/WMA/WAV playback, there are three repeat play ranges: FLD (folder
repeat), TRK (one-track repeat) and DSC (repeat all tracks).
1. Press FUNCTION to select RPT.
Press FUNCTION until RPT appears in the display.
2. Press 4or 6to select the repeat range.
Press 4or 6until the desired repeat range appears in the display.
•FLD– Repeat the current folder
•TRK– Repeat just the current track
•DSC– Repeat all tracks
Notes
•If you select another folder during repeat play, the repeat play range changes to DSC.
•If you perform track search or fast forward/reverse during TRK, the repeat play range
changes to FLD.
•When FLD is selected, it is not possible to play back a subfolder of that folder.
햲Function display
Shows the function status.
햳RPT indicator
Shows when repeat range is
selected to current track (file).
Playing tracks in random order
Random play lets you play back tracks in a random order within the repeat range, FLD
and DSC.
1. Select the repeat range.
Refer to “Repeating play” on this page.
2. Press FUNCTION to select RDM.
Press FUNCTION until RDM appears in the display.
3. Press 8to turn random play on.
RDM :ON appears in the display. Tracks will play in a random order within the
previously selected FLD or DSC ranges.
4. Press 2to turn random play off.
RDM :OFF appears in the display. Tracks will continue to play in order.
Note
•If you turn random play on during FLD and then return to the playback display, FRDM
appears in the display.
Scanning folders and tracks
While you are using FLD, the beginning of each track in the selected folder plays for
about 10 seconds. When you are using DSC, the beginning of the first track of each
folder is played for about 10 seconds.
1. Select the repeat range.
Refer to “Repeating play” on this page.
2. Press FUNCTION to select SCAN.
Press FUNCTION until SCAN appears in the display.
3. Press 8to turn scan play on.
SCAN :ON appears in the display. The first 10 seconds of each track of the current
folder (or the first track of each folder) is played.
4. When you find the desired track (or folder) press 2to turn scan play off.
SCAN :OFF appears in the display. The track (or folder) will continue to play.
•If the display has automatically returned to the playback display, select SCAN again
by pressing FUNCTION.
Notes
•After track or folder scanning is finished, normal playback of the tracks will begin again.
•If you turn scan play on during FLD and then return to the playback display, FSCN appears
in the display.
MAN-DEH-P5800MP-GB.fm Page 19 Friday, September 30, 2005 3:15 PM

20
ENGLISH
MP3/WMA/WAV Player
Pausing MP3/WMA/WAV playback
Pause lets you temporarily stop playback of the MP3/WMA/WAV.
1. Press FUNCTION to select PAUSE.
Press FUNCTION until PAUSE appears in the display.
2. Press 8to turn pause on.
PAUSE:ON appears in the display. Play of the current track pauses.
3. Press 2to turn pause off.
PAUSE:OFF appears in the display. Play will resume at the same point that you turned
pause on.
Note
•You can also turn pause on or off by pressing PAUSE.
Selecting the search method
You can switch the search method between fast forward/reverse and searching every
10 tracks.
1. Press FUNCTION to select FF/REV.
Press FUNCTION until FF/REV appears in the display.
•If the search method ROUGH has been previously selected, ROUGH will be
displayed.
2. Press 4or 6to select the search method.
Press 4or 6until the desired search method appears in the display.
•FF/REV– Fast forward and reverse
• ROUGH – Searching every 10 tracks
Searching every 10 tracks in the current folder
If the current folder contains over 10 tracks, you can search every 10 tracks. When one
folder contains a lot of tracks, you can roughly search for the track you want to play.
1. Select the search method ROUGH.
Refer to “Selecting the search method” on this page.
2. Press and hold 4or 6to search every 10 tracks in the current folder.
•If the current folder contains less than 10 tracks, pressing and holding 6recalls the
last track of the folder. Also, if the remaining number of tracks after searching every
10 tracks is less than 10, pressing and holding 6recalls the last track of the folder.
•If the current folder contains less than 10 tracks, pressing and holding 4recalls the
first track of the folder. Also, if the remaining number of tracks after searching every
10 tracks is less than 10, pressing and holding 4recalls the first track of the folder.
Using compression and BMX
Using the COMP (compression) and BMX functions let you adjust the sound playback
quality of this player. Each of the functions has a two-step adjustment. The COMP
function balances the output of louder and softer sounds at higher volumes. BMX
controls sound reverberations to give playback a fuller sound. Listen to each of the
effects as you select through them and use the one that best enhances the playback
of the track or CD that you are listening to.
1. Press FUNCTION to select COMP.
Press FUNCTION until COMP appears in the display.
2. Press 8or 2to select your favorite setting.
Press 8or 2repeatedly to switch between the following settings:
COMP OFF – COMP 1 – COMP 2 – COMP OFF – BMX 1 – BMX 2
Displaying text information on MP3/WMA disc
Text information recorded on a MP3/WMA disc can be displayed.
*Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
Play time – FOLDER (folder name) – FILE (file name) – TRK TTL (track title) – ART
NAME (artist name) – ALBM TTL (album title) – COMMENT (comment) – Bit rate
•When playing back MP3 files recorded as VBR (variable bit rate) files, the bit rate
value is not displayed even after switching to bit rate.
•When playing back WMA files recorded as VBR files, the average bit rate is
displayed.
•If specific information has not been recorded on an MP3/WMA disc, NO XXXX will
be displayed (e.g., NO NAME).
MAN-DEH-P5800MP-GB.fm Page 20 Friday, September 30, 2005 3:15 PM