Pioneer DV-585A-S User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
STANDBY/ON


585A
DV-585A-S
RRV3161
DVD PLAYER
DV-585A-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Region No. Remarks
DV-585A-S WYXTL AC220-240V 2
DV-585A-S WVXTL AC220-240V 2
DV-585A-K WYXTL AC220-240V 2
DV-585A-S WYXTL/UR AC220-240V 5
For details, refer to "Important Check Points for Good Servicing" .
T-ZZR MAY 2005 printed in Japan

DV-585A-S
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-
it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trainedto properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and
may void the warranty. If you are not qualified to perform the repair of this product properly and
safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1
BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR
CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm
Additional Laser Caution
∗: See page 49.
1.
• Laser diode is driving with Q2303,Q2305(650nm LD) and Q2302,
Q2304(780nm LD)on the DVD MT PCB Assy.
Therefore, when short-circuit between the emitter and collector of these
transistors or the base voltage is supplied for transistors turn on, the
laser oscillates. (failure mode)
• In the test mode ∗, there is the mode that the laser oscillates except
for the disc judgment and playback. LD ON mode in the test mode
oscillates with the laser forcibly.
2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.
LABEL CHECK
(Printed on the Rear Panel)
Location: inside of the unit
VORSICHT
: SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG,WENNABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETZEN !
CAUTION
: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.
ADVARSEL
: SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÀLING.
VARO!
: AVATTAESSA ALTISTUT NÄKYVÄ JA NÄKYMÄTTÖMÄLLE LASERSATEIL YLLE. ÄLÄ KATSO SÄTEESEN.
VARNING
: SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN.
7260000356 SH
CUIDADO
: RADIACIÓN LÁSER VISIBLE E INVISIBLE AL ESTAR ABIERTO. EVITAR EXPOSICIÓN AL RAYO.

DV-585A-S 3
5678
5678
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DV-585A-S
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING SECTION .................................................................................................................................. 6
2.2 EXTERIOR SECTION............................................................................................................................... 8
2.3 05 DVD MECHA SECTION...................................................................................................................... 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL WIRING CONNECTION DIAGRAM........................................................................................ 14
3.3 DVD MT PCB (1/6) ASSY ........................................................................................................................ 16
3.4 DVD MT PCB (2/6) ASSY ........................................................................................................................ 18
3.5 DVD MT PCB (3/6) ASSY ........................................................................................................................ 20
3.6 DVD MT PCB (4/6) ASSY ........................................................................................................................ 22
3.7 DVD MT PCB (5/6) ASSY ........................................................................................................................ 24
3.9 OPERATION and OPERATION 2 PCB ASSYS ....................................................................................... 28
3.10 POWER PCB (1/2) ASSY ...................................................................................................................... 30
3.11 POWER PCB (2/2) ASSY ...................................................................................................................... 32
3.12 WAVEFORMS ........................................................................................................................................ 34
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 37
4.1 LOADING and SW PCB ASSYS.............................................................................................................. 37
4.2 DVD MT PCB ASSY................................................................................................................................. 38
4.3 OPERATION and OPERATION 2 PCB ASSYS ....................................................................................... 42
4.4 POWER PCB ASSY................................................................................................................................. 44
5. PCB PARTS LIST ........................................................................................................................................... 46
6. ADJUSTMENT ............................................................................................................................................... 48
6.1 WHEN REPLACING DVD DECK ............................................................................................................. 48
6.2 TEST MODE ............................................................................................................................................ 49
6.3 TEST MODE IN........................................................................................................................................ 50
6.4 DISC REMOVAL METHOD...................................................................................................................... 51
7. GENERAL INFORMATION ............................................................................................................................. 52
7.1 DIAGNOSIS ............................................................................................................................................. 52
7.1.1 DISPLAY SPECIFICATION OF THE TEST MODE............................................................................ 52
7.1.2 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY ............................................................ 53
7.1.3 SPECIFICATION OF MODEL INFORMATION DISPLAY .................................................................. 54
7.1.4 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ............................................................. 55
7.1.5 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY .................. 56
7.1.6 TROUBLE SHOOTING...................................................................................................................... 57
7.2 DISASSEMBLY ........................................................................................................................................ 59
7.3 IC INFORMATION.................................................................................................................................... 64
8. PANEL FACILITIES ........................................................................................................................................ 76
8.1 FRONT PANEL SECTION ....................................................................................................................... 76
8.2 DISPLAY .................................................................................................................................................. 77
8.3 REMOTE CONTROL ............................................................................................................................... 78

DV-585A-S 5
5678
5678
C
D
F
A
B
E
1. SPECIFICATIONS
Specifications
General
System. . . . . . . . . . . . . . . . . . . . . . . . .DVD player
Power requirements. . . AC 220–240 V, 50/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . .8W
Power consumption (standby) . . . . . . . . 0.85 W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 kg
Dimensions
. . . . . . . . . . 420 (W) x 49.5 (H) x 214.9 (D) mm
Operating temperature . . . . . . . .+5°C to +35°C
Operating humidity. . . . . . . . . . . . . . . 5% to 85%
(no condensation)
AV connector output
AV Connector (21-pin connector assignment)
AV connector output . . . . . . . . 21-pin connector
This connector provides the video and audio
signals for connection to a compatible colour TV
or monitor.
PIN no.
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 2/R out
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 1/L out
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B out
8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G out
15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R out
17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND
19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video out
21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND
Component video output
Y (luminance) - Output level. . . . . . 1 Vp-p (75 Ω)
PB(color) - Output level . . . . . . . . 0.7 Vp-p (75 Ω)
PR(color) - Output level. . . . . . . . 0.7 Vp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA
S-video output
Y (luminance) - Output level. . . . . . 1 Vp-p (75 Ω)
C (color) - Output level . . . . . . . 286 mVp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-video
Video output
Output level . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
Audio output (1 stereo pair)
Output level . . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . . 2
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
Audio output (multi-channel / L, R, C, SW,
SL, SR)
Output level . . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . . 6
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
Digital audio characteristics
Frequency response. . . . . . . . . . . 4 Hz to 44 kHz
(DVD fs: 96 kHz)
4 Hz to 48 kHz (DVD-Audio fs: 192 kHz)
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 dB
Dynamic range. . . . . . . . . . . . . . . . . . . . . . 101 dB
Total harmonic distortion . . . . . . . . . . . 0.0023 %
Wow and flutter . . . . . . . . Limit of measurement
(±0.001% W. PEAK) or lower
Digital output
Coaxial digital output. . . . . . . . . . . . . . . RCA jack
Optical digital output . . . . . . . O ptical digital jack
Accessories
Audio/video cable . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . 2
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating Instructions

DV-585A-S
6
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING SECTION
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
15
14
3
4
14
3
For WVXTL type
For WVXTL type and WYXTL/UR type
For WVXTL type Only
For WYXTL type and WYXTL/UR type
For WYXTL type
4
2
1
1
5
2
13
12
6
16
16
12
6
7 or 11
17
8-10
"Operating Instructions"
Front

DV-585A-S 7
5678
5678
C
D
F
A
B
E
PACKING SECTION parts List
(2) CONTRAST TABLE
DV-585A-S/WYXTL, /WVXTL, /WYXTL/UR and DV-585A-K/WYXTL are constructed the same except for the follow-
ing :
Mark No. Description Part No.
1 Cord set AC See Contrast table (2)
2 Cord, RCA Pin 06CPBA2006
3 Remote Control VXX2914
4 Battery Cover VNK4998
NSP 5 Battery,Mangan (AR, R6P) 141L003010
NSP 6 Guarantee Card J2G60402A
7 Operating Instructions See Contrast table (2)
8 Operating Instructions See Contrast table (2)
9 Operating Instructions See Contrast table (2)
10 Operating Instructions See Contrast table (2)
11 Operating Instructions See Contrast table (2)
12 Polyethylene Bag See Contrast table (2)
13 Gift Sheet 791WHA0100
14 Package See Contrast table (2)
15 Gift Box See Contrast table (2)
NSP 16 Poly. Bag 791WHAA040
17 Package.Pad 792WHA0604
Mark No. Description Part No.
Mark No. Symbol and Description DV-585A-S/WYXTL DV-585A-S/WVXTL DV-585A-S/WYXTL/
UR DV-585A-K/WYXTL
> 1 Cord Set AC 1206158802 1206138802 1206158802 1206158802
7 Operating Instructions (English) Not used J2G60301B Not used Not used
8 Operating Instructions (English, Italian) J2G60421A Not used Not used J2G60421A
9Operating Instructions (German, French) J2G60422A Not used Not used J2G60422A
10 Operating Instructions (Spanish, Duch) J2G60423A Not used Not used J2G60423A
11 Operating Instructions (Russian) Not used Not used J2G61001A Not used
12 Polyethylene Bag, Instruction JB5UD400 JB5UD200 JB5UD200 JB5UD400
14 Package 792WHA0588 792WHA0597 792WHA0588 792WHA0588
15 Gift Box 793WCDC698 793WCDC764 793WCDC763 793WCDC769

DV-585A-S
8
1234
1234
C
D
F
A
B
E
2.2 EXTERIOR SECTION
101K
101C
101L
12
12
101E
101D
101H
101G
101J
101I
101B
101F
101A
PCB130
(DVD PCB ASS'Y)
A
A
A
CONTACT SIDE
NON-CONTACT
SIDE
A
B
C
F
Refer to
"2.3 05 DVD MECHA ASSY".
" FRONT PANEL SECTION".
20
20
20
20
20
1
19
19
21
21
21
21
13
8
19
4
5
14
19 19
13
2
3
19
19
101
722
22
26
22
11
13
13
16
16 10
6
19
18
18
18
18
PCB240
(POWER PCB ASS'Y)
9
23
24
25
PCB280
(OPERATION 2 PCB ASS'Y)
PCB270
(OPERATION 1 PCB ASS'Y)
15
17

DV-585A-S 9
5678
5678
C
D
F
A
B
E
EXTERIOR SECTION parts List
(2) CONTRAST TABLE
DV-585A-S/WYXTL, /WVXTL, /WYXTL/UR and DV-585A-K/WYXTL are constructed the same except for the follow-
ing :
Mark No. Description Part No.
1DVD MT PCB Assy A2G604A130
2 OPERATION PCB Assy A2G604A270
3 OPERATION 2 PCB Assy A2G502A280
>
4POWER PCB Assy A2G604A240
>
5DVD MECHA ASSY A2G512A650
6 Shield, 21Pin 761WSA0237
7 Holder, Display 762WSA0368
NSP 8 Plate,Bottom 702WSA0238
>
9 Fuse (F501 : 1.6A) 080NT1R604
10 Sheet, Caution 7260000356
11 Plate,Cover Power 755WPA0046
12 Holder,FFC 761WPA0396
13 Cushion, Leg VEB1349
14 Cabinet, Top See Contrast table (2)
15 Sheet, Caution 725000A088
16 Cushion (15x20x16) 8965TS1015
NSP 17 POP Label 7236310020
18 Screw,Tap Tite(S)Bind Wash. 816423063U
19 Screw,Tap Tite(S) (3x5.5) 8107D3055U
20 Screw,Tap Tite(B) (3x6.0) See Contrast table (2)
21 Screw,Tap Tite(B)Pan (3x6) 810913060U
22 Screw,Tap Tite(P)Bind (2.6x8) 811022680U
23 Sheet,Jack 1 7226310050
24 Sheet,Jack 2 See Contrast table (2)
25 Sheet,Jack 3 See Contrast table (2)
26 Double,Face-Tape 7290000156
27 • • • •
28 • • • •
101 Front Cabi Assy See Contrast table (2)
NSP 101A Cabinet, Front See Contrast table (2)
NSP 101B Plate, Display 711WPA0225
101C Flap, DVD See Contrast table (2)
101D Badge, Brand See Contrast table (2)
NSP 101E Button, Cap Power See Contrast table (2)
NSP 101F Button, Cap Play See Contrast table (2)
NSP 101G Button, Frame 3 738WPA0131
NSP 101H Button, Frame 4 738WPA0137
NSP 101I Button, Frame 1 See Contrast table (2)
NSP 101J Button, Frame 2 See Contrast table (2)
101K Spring,Flap-DVD 743WKAA012
NSP101L Holder, Display 761WPA0368
Mark No. Description Part No.
Mark No. Symbol and Description DV-585A-S/WYXTL DV-585A-S/WVXTL DV-585A-S/WYXTL/
UR DV-585A-K/WYXTL
14 Cabinet, Top 702WSB0114 702WSB0114 702WSB0114 702WSB0115
20 Screw,Tap Tite(B) (3x6.0) 8109K3060U 8109K3060U 8109K3060U 8109K3060S
24 Sheet,Jack 2 722631A027 722631A027 722631A027 722631A024
25 Sheet,Jack 3 722631A028 722631A028 722631A038 722631A028
101 Front Cabi Assy 7A701A393A 7A701A393A 7A701A393A 7A701A459A
NSP 101A Cabinet, Front 701WPJD002 701WPJD002 701WPJD002 701WPJD061
101C Flap, DVD 712WPJC151 712WPJC151 712WPJC151 712WPJC152
101D Badge, Brand 7236310014 7236310014 7236310014 7236310009
NSP 101E Button, Cap Power 737WPEA001 737WPEA001 737WPEA001 737WPA0024
NSP 101F Button, Cap Play 737WPEA002 737WPEA002 737WPEA002 737WPA0025
NSP 101I Button, Frame 1 738WPB0050 738WPB0050 738WPB0050 738WPA0156
NSP 101J Button, Frame 2 738WPB0051 738WPB0051 738WPB0051 738WPA0157

DV-585A-S
10
1234
1234
C
D
F
A
B
E
2.3 05 DVD MECHA SECTION
Applying positions AA, AB and AC for the
grease are displayed for this section.
Check if the correct grease is applied for each
position.
NOTE:
CLASS MARK
GREASE G-478B AA
PN-397 AB
PART NO.
GEM1018
PART NAME
GYA1001
ME-913A AC
GEM1036
Cannot supply separately.
If the repair is needed, replace the
DVD MECHA ASS'Y.
PCB610
(LOADING MOTOR PCB ASS'Y)
CD2302
Do not replace the parts. Because,
minute adjustments are needed if
this condition is disassembled
further more.
If the repair is needed, replace the
DVD MECHA ASS'Y.
(SW PCB ASS'Y)
10
AB
AB
AB
AA
34
15
14
21
18
11
23
9
AB
19
1
29
AB
AB
3
12
20
6
4
SW1
31
PCB640
27
22
22
16
2
CD2001
24
5
25
26
32
8
13
35
8
30
SW2
33 CD2301
AC
AC
AB
D
E
Lubricating Oil
GYA1001
Daifree
GEM1036
Note :
Lubricating Oil
GYA1001
7
17
28

DV-585A-S 11
5678
5678
C
D
F
A
B
E
05 DVD MECHA SECTION parts List
Mark No. Description Part No.
1 Loading Motor PCB Assy A2F101A610
2 Gear,Middle 92P100117A
>
3 Loading Motor 1515S98004
4 Pulley,Motor 92P100097A
>
5 FEED Motor 1515S98004
6 Cord Jumper (24P)(CD2001) 122H002305
7 Cord Jumper (CD2302) 122H051602
8 Insulator (F) 92P200013A
9 Belt,Loading 92P200015A
10 Insulator (R) 92P200016A
11 Frame,main 92P100119A
12 Tray (B) 92P100127A
13 Holder ,Traverse 92P100125A
14 Gear,Pulley 92P100123A
15 Gear,Main 92P100124A
16 Gear,Feed 92P100116A
17 SW PCB Assy (PCB640) A2F101A640
18 Plate,Clamper 92P000023A
NSP 19 Loader SUB Assy 92AAA0019A
20 Clamper 92P100122A
21 Screw,Pan (M1.7x3 P3) 814011730U
22 Screw,Pan (M1.7x2.3 P3) 814011723U
23 Rack,Loading 92P100121A
24 Gear,Motor 92P100088A
25 Feed Rack Assy 92AAA0017A
26 Screw,T-Tite(B) (M1.7x5.0 P3) 813381750U
27 Screw,Gear Feed 92P700007A
28 Cord Jumper (CD2301) 122H061605
29 Switch (SW1) 0515S32003
30 Push Switch (SW2) 0500101036
31 Screw,Tap Tite(P) (2.6x8) 811022680U
32 Sems.Tap Tite(P) (2x8) 816112080U
33 Screw (Bind 2x8) 811022080U
>
34 DVD MECHA ASSY A2G512A650
NSP 35 Traverse SUB ASSY 92AAA0016A

DV-585A-S
12
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
11 11
ACP2301
IC2301
Motor Drive
IC
X4001
(27MHz)
IC651
FIP Driver IC
V651 FL TUBE
IC4002
MPEG / MICON
/ RF-AMP
IC4004
16Mbit Flash
CP2303CD2301
PICKUP
SPINDLE
MOTOR
10 10
B
7 7
C
S_Y
6 6
D
6 1
SP1+
5 2
SP1–
4 3
SLD+
3 4
SLD–
21 21
T+
22 22
T–
23 23
F+
24 24
F–
5 5
E
2 2
10
10
11
11
9
9
6
6
30
7
6
9
8
11
10
51213 4
48
19
18
2
5
4
3
194
49
F
M
SLED
MOTOR M
SW PCB ASSY
DVD MECHA
ASSY
D
DVD MT PCB ASSY
A
A
OPERATION 2
PCB ASSY
COPERATION
PCB ASSY
B
CP2302CD2302
LOADING
MOTOR
SW1
2 4
LD+
1 5
LD–
3 3
OPEN
5 1
CLOSE
M
LOADING MOTOR
PCB ASSY
E
IC4005
64Mbit SDRAM
IC4001
EEPROM
S_C
196
CR
203
Y
200
CB
202
CVBS
198
228 229
ASPDIF
CP4002
CP601
CP602CP603
225
V+3E
V+3E
FLDC+
FLDC–
-28V
Power
219
218
217
ASDAT2
ASDAT1
ASDAT0
1/6

DV-585A-S 13
5678
5678
C
D
F
A
B
E
IC7301
Video Driver
6 ch
IC4006
REG+1.8V IC
T501
Power Transformer
F501
Fuse
2
3
5
6
8
9
12
13
14
2
3
5
6
8
9
12
13
14
L
N
6
2 3
2
14
10
12
4
21
26
16
20
18
23
A
A
A
POWER PCB ASSY
F
S_C OUT
CR out
S_Y OUT
L
J7301
J8102
R
CR
J7302
CP502CP4003
J501
Y
CB
CVBS
DIGITAL OUT
COAXIAL
S2 VIDEO OUT
VIDEO
OUT
AC IN
Y out
CB out
P.CON+12V
V out
AT+12V for MUTE
P.CON+5V
P.CON+6V
P.CON+3.3V
AT+3.3V
FL DC–
FL DC+
-28V
V+3
V+5V V+5S
V+3A V+3E
V+3F
V+12
V+12AT
V+6A
V+5A
(AUDIO DAC)
(MPEG SDRAM FLASH)
(AUDIO VIDEO DAC)
(FLIP/LED/IR/RESET)
(CORE)
(AUDIO AMP)
(AUDIO MUTE)
(MOTOR)
(VIDEO OPT/COAX) (OPU)
(F/E)
V+1P8
OPTICAL
IC8001
4 ch BUS SW
5
1
3
8
10
12
8
12
10
5
3
1
15
11
7
19
3
1
9
4
7
2
5
11
10
3
6
CP7301 CP503 J8101
R
L
CVBS
B
G
R
SCART
R
G
B
CVBS
AUDIO L
AUDIO R
IC8004 PCM1742KE
AUDIO DAC (C, Lfe)
AUDIO LPF & AMP
3
2IC8006-1/2
BA4560F
IC8006-2/2
1
8
5
67
IC8005 PCM1742KE
AUDIO DAC (Ls, Rs)
3
2IC8007-1/2
BA4560F
IC8007-2/2
1
8
5
67
IC8003 PCM1742KE
AUDIO DAC (L, R)
3
2IC8008-1/2
BA4560F
IC8008-2/2
1
8
5
67
VOUTL
VOUTR
7
8
2
ASDAT2
VOUTL
VOUTR
7
8
2
ASDAT1
VOUTL
VOUTR
7
8
2
1
3
16
ASDAT0
OS8101
Q8103
CP8001
(2P)
CP8102
(2P)
SPDIF
1 1
GND
2 2
J8002
J8002
J8001
AUDIO
OUT
(5.1 ch)
CENTER
SUB
WOOFER
SURROUND
L
R
FRONT
L
R
AUDIO
OUT (2 ch)
Å
4/6
5/6
6/6

DV-585A-S
14
1234
1234
C
D
F
A
B
E
3.2 OVERALL WIRING CONNECTION DIAGRAM
24
23
22
21
20
19
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
24
23
22
21
20
19
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
24
23
22
21
20
19
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
CP2301
5
4
3
2
1
1
2
3
4
5
CP2302
6
5
4
3
2
1
CP2303
DVD/CD(SW)
LIMIT SW
LD-
LD+
GND(D)
CLOSE
OPEN
LOADING MOTOR
SW(GND)
SLD-
SLD+
SP1-
SP1+
FFC
SLED MOTOR
SPINDLE
MOTOR
6
5
4
3
2
1
VREF
MON(DVD)
NC
VOL(DVD)
GND(DVD)
LD(DVD)
VOL(CD)
GND(CD)
GND(DVD)
MON(COM)
RF
C
B
A
D
F
E
VCC
GND
F-
F+
T-
T+
VS
NC
SW1(DVD/CD)
LD_DVD(650)
PD/GND
LD_CD(780)
VR780(CD)
GND
GND
VR650(DVD)
VRF(RF_OUT)
C
B
A
D
F
E
VCC
GND
TRKG RIN
TRKG DRV
FOCS RTN
FOCS DRV
1
2
3
4
5
6
OPTICAL PICKUP
SSS-13-2
SW1
GND(SW)
SW-2(CLOSE)
SW-1(OPEN)
LOADING MOTOR(-)
LOADING MOTOR(+)
BCZ3B52
M2603
GND(SW)
FEED MOTOR (+)
SPINDLE MOTOR (+)
SPINDLE MOTOR (-)
FEED MOTOR (-)
PICK UP INNER LIMIT SWITCH
JCV9B06
M2601
M
M
M
BCZ3B03
M2602
SW2
ESE22MH24
CD2301
CD2302
2H062102
2H052601
VRCOM
CP4002
1110
987654321
1110
987654321
CP601
CLK
DI (M to F)
STB
FL DC+
FL DC –
– 28V
DGND DGND
V+ 3E
I R
DO (F to M)
3
4
5
6
CP603
6
5
4
3
CP602
069EVB3050
069EVB3030
069EV63050
069EV63050
6
5
4
3
3
2
4
5
6
2
+SKIP
+SKIP
SW2
PAUSE/–SKIP
POWER
SW2
2
1
2
1
1
STOP
SW1
STOP
SW1
PAUSE/–SKIP
POWER
1
DVD MECHA ASSY (A2G512A650)
SW PCB ASSY
(A2F101A640)
D
LOADING MOTOR
PCB ASSY
(A2F101A610)
E
CD601(11P FFC)
122H0B1002
CD603(6P FFC)
122H062801
D E
OPERATION
PCB ASSY
(A2G604A270)
B
OPERATION 2
PCB ASSY
(A2G502A280)
C

DV-585A-S 15
5678
5678
C
D
F
A
B
E
CP502
14 13 12 11 10
9 8 7 6 4 5 3 2 1
CP4003
14 13 12 11 10
9
6 5 4 3 2 1 8 7
14 13 12 11 10
9
6 5 4 3 2 1 8 7
14 13 12 11 10
9
6 5 4 3 2 1 8 7
069S2E0629
AT+12V for MUTE
GND
P. CON+ 12V
GND
P. CON+5V
P. CON+6V
GND(M)
P. CON+3.3V
AT+3.3V
P. ON-H
GND(D)
FL DC –
FL DC +
– 28V
AT+12V for MUTE
GND
P. CON+ 12V
GND
P. CON+5V
P. CON+6V
GND(M)
P. CON+3.3V(AT)
AT+3.3V
STBY L
GND(D)
FL DC –
FL DC +
– 28V
DVD MT PCB ASSY (A2G604A130)
A1/6- A6/6
A
F1/2- F2/2
: MPEG/MICON/RF-AMP BLOCK
A1/6
: MEMORY BLOCK
A2/6
: LOADER/MOTOR DRV BLOCK
A3/6
: AUDIO JACK BLOCK
A4/6
: VIDEO SEC BLOCK
A5/6
: POWER PORT BLOCK
A6/6
: POWER BLOCK
F1/2
: DIGITAL AUDIO BLOCK
F2/2
POWER PCB ASSY (A2G604A240)
F
CVBS
VIDEO OUT
(COMPOSITE)
J7302
J7301
Y
Cb
Cr
S VIDEO OUT
AUDIO OUT
L
J8001
R
J501
LIVE BLUE
BROWN
AC IN
1
2
NEUTRAL
Y
C
CP502(14P)
Cord Connector
06C32E3504
C3223003
CP8102
SPDIF
GND 2
1
A2001WV2-2P
CP8001
SPDIF
GND2
1
2 1
2 1
J8002
J8002
J8001
AUDIO
OUT
(5.1 ch)
CENTER
SUB
WOOFER
SURROUND
L
R
FRONT
L
R
÷When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷The >mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷: The power supply is shown with the marked box.
COAXIAL
J8102
OS8101
DIGITAL
AUDIO
OUT
OPTICAL
069J7C0599 069J7C0599
CP503
12 11 10
9 8 7 6 4 5 3 2 1
CP7301
12 11 10
9
6 5 4 3 2 1 8 7
1 2 3 4 7 8 9
10 11 12
5 6
1 2 3 4 7 8 9
10 11 12
5 6
B/CB
G/Y
GND GND
R/CR
RGB-H
FS
CVBS
GND
AUDIO L
GND
AUDIO R
B
G
GND GND
R
RGB-H
FS
CVBS
GND
AUDIO L
GND
AUDIO R
SCART
J8101
CD8001(12P FFC)
122HC0C3001

DV-585A-S
16
1234
1234
C
D
F
A
B
E
3.3 DVD MT PCB (1/6) ASSY
(RF)
(D)
(A)
(B)
(C)
(E)
(F)
(D)
(A)
(B)
(C)
(E)
(RF) (RF)
(F)
1
17 MPEG/MICON
DVD MT PCB ASSY (A2G604A130)
A1/6
MPEG/MICON/RF-AMP BLOCK
3/6A2/6A
A1/6
EEPROM

DV-585A-S 17
5678
5678
C
D
F
A
B
E
: VIDEO SIGNAL ROUTE
(RF) : RF SIGNAL ROUTE
(SY) : S VIDEO SIGNAL ROUTE (Y ch)
(SC) : S VIDEO SIGNAL ROUTE (C ch)
(R/CR) : VIDEO SIGNAL ROUTE (R/CR ch)
(G/Y) : VIDEO SIGNAL ROUTE (G/Y ch)
(B/CB) : VIDEO SIGNAL ROUTE (B/CB ch)
(D) : AUDIO DATA SIGNAL ROUTE
(DA) : AUDIO SIGNAL ROUTE (Digital)
(SY)
(SC)
(SY)
(SC)
(R/CR)
(G/Y)
(B/CB)
(R/CR)
(G/Y)
(B/CB)
(D)
(DA)
(D)
(DA)
A1/6
CP601
B
6/6A
4/6A
5/6A
RESET IC

DV-585A-S
18
1234
1234
C
D
F
A
B
E
3.4 DVD MT PCB (2/6) ASSY
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST
AT THE TIME OF PRINTING AND SUBJECT TO
CHANGE WITHOUT NOTICE
NOTE : THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
DVD MT PCB ASSY (A2G604A130)
A2/6
MEMORY BLOCK
A2/6
1/6A
1/6A

DV-585A-S 19
5678
5678
C
D
F
A
B
E
64Mbit SDRAM
16Mbit FLASH
A2/6

DV-585A-S
20
1234
1234
C
D
F
A
B
E
3.5 DVD MT PCB (3/6) ASSY
NOTE : THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST
AT THE TIME OF PRINTING AND SUBJECT TO
CHANGE WITHOUT NOTICE
(F) (F)
(E) (E)
(D) (D)
(C) (C)
(B) (B)
(RF) (RF)
(A) (A)
A3/6
DVD MT PCB ASSY (A2G604A130)
A3/6
LOADER/MOTOR DRV BLOCK
CD2302
ETo PICKUP
CD2301
D