Pioneer PDP 507CMX Operating manual

PDP-507CMX INDUSTRIAL PLASMA DISPLAY PANEL
SERIAL COMMAND REFERENCE MANUAL (version 1.0)
This manual provides information for controlling the PDP-507CMX industrial plasma display panel
with an external communication device by using serial commands.
Released: January 23, 2007
TABLE OF CONTENTS
1 About the RS-232C Adjustment............................................................................ 2
2 Interface .................................................................................................................. 3
3 Combination Connection ...................................................................................... 4
4 ID Assignment........................................................................................................ 5
5 List of Commands.................................................................................................. 7
6 QUEST Commands ................................................................................................ 15

2
RS-232C Adjustment
This display has an RS-232C terminal. It is possible to use a PC to make various adjustments and settings.
1 About the RS-232C Adjustment
Adjustments using the RS-232C:
• The adjustments are written to the same memory area as for the integrator mode (refer to section 5.4.4, “PICTURE,
White Balance and SCREEN Position Adjustment Values Memory Area Tables” (pg. 257 to 261)).
(1) Assign an ID before using the RS-232C adjustment. Include the panel ID in the RS-232C command.
For details, refer to section 5.5.2, “Interface” (pg. 263).
(2) Of the adjustment values and setting items set by RS-232C commands, there are some items that are
stored in memory and some that are not. For details, refer to section 5.5.5, “List of RS-232C Commands”
(pg. 267). Also, when storing values in “last” memory, the conditions described in section 5.1.5, “Last
Memory” (pg. 170), must be satisfied.
(3) <OSDS00>/<OSDS01> (OSD display disable/enable setting)
Regardless of the setting, the following items can be displayed.
• Menu display (menu mode, integrator mode)
• Warnings before Auto Power OFF or Power Management operation
• Warning of high temperature inside the panel
• Display announcing that the FUNCTIONAL LOCK is set and the FUNCTIONAL LOCK setting display
• Display call (including holding a button down)
(4) When using RS-232C commands, control the input signal as well as the power. If the power is ON when
there is no signal, the display continues to have a weak discharge. This activity can affect the life of the
display.
Note
RS-232C Adjustment

3
RS-232C Adjustment
2 Interface
1) Connector
D-sub 9 pins (male/straight)
2) Pin layout
3) Baud Rate
9 600 bps (standard)
(switch-able to 1 200, 2 400, 4 800, 19 200, 38 400 bps)
Note
The baud rate of this display should be set to match the baud rate of the PC.
Also, when the RS-232C cable is extended over a long distance, use a slower baud rate.
4) Data format
Start bit: 1 bit
Data bit: 8 bit
Parity: no
Stop bit: 1 bit
5) Connection
6) Protocol
From the PC to the display
Straight Cable
* D-sub 9-pin/D-sub 25-pin conversion tables are now available on the market.
Control PC Control PC
(with D25 serial port ) Plasma Display (with D9 serial port) Plasma Display
2
2
3
2
3
2
RXD 3 2 TXD RXD 2 2 TXD
TXD 2 3 RXD TXD 3 3 RXD
CTS 5 8 RTS CTS 8 8 RTS
GND 7 5 GND GND 5 5 GND
5
96
1
Pin No. Signal
1 NC (not connected)
2 TxD (Transmit Data)
3 RxD (Receive Data)
4 NC (not connected)
5 GND
Pin No. Signal
6 NC (not connected)
7 NC (not connected)
8 RTS (Request To Send)
9 NC (not connected)
(1) Sending one command at a time:
STX (02 hex) ID (2 Byte) COMMAND (3 Byte or 6 Byte) ETX (03 hex)
(2) Sending numerical direct commands:
STX (02 hex) ID (2 Byte) COMMAND (3 Byte) ARGUMENT (3 Byte) ETX (03 hex)
ID, COMMAND, ARGUMENT are transmitted as ASCII characters.
From the display to a PC
(1) Echo back (Normal response)
Command received and returned but the ID is not returned.
STX (02 hex) COMMAND (3 Byte or 6 Byte) ETX (03 hex)
Received command is a numerical direct effect command and numerical data is returned:
STX (02 hex) COMMAND (3 Byte) ARGUMENT (3 Byte) ETX (03 hex)
(2) Error (Abnormal response)
Received command is a non-corresponding command, ‘ERR’is returned:
STX (02 hex) ERR (3 Byte) ETX (03 hex)
Received command cannot be processed (when PON is received when the power is already ON, etc.), ‘XXX’is
returned:
STX (02 hex) XXX (3 Byte) ETX (03 hex)

4
RS-232C Adjustment
3 Combination Connection
When controlling/adjusting panels, it is convenient to connect several displays to one PC.
By performing a combination connection and assigning IDs to the panels, it is possible to control and adjust several
displays at the same time or separately.
Connection method:
Connect the panels as shown in the figure below.
Only the combination IN terminal or the RS-232C terminal can be used at the same time. Connecting them at the
same time could cause errors. Also, do not pair combination IN terminals or combination OUT terminals. Doing so
could cause communication to fail.
It is possible to use a general-purpose mini DIN 6-pin (straight) cable for the combination cable.
Note
To output RS-232C signals from the combination OUT terminal, an ID must be assigned.
For details, refer to section, 5.5.4, “ID Assignment”(pg. 265).
Note
IN OUT
RS-232C
IN OUT IN OUT
RS-232C
COMBINATION
RS-232C
COMBINATIONCOMBINATION
First Panel Second Panel Third Panel
Combination cable
Combination cable
PC
OUT IN IN
OUT

5
RS-232C Adjustment
4 ID Assignment
The ID is assigned from the PC.
Commands: <IDC> (ID CLEAR) ........ Clears the assigned ID
<IDS> (ID SET) ............. Assigns an ID
IDS is only effective when an ID is not assigned.
IDs are assigned starting from the panel closest to the PC.
Example: Case of 4 displays (assigning IDs with the PC for the first time)
First, connect an RS-232C and combination cables. (Refer to section 5.5.3, “Combination Connection”(pg.
264).)
By sending RS-232C commands in this order, it is possible to assign an ID for each panel.
When a panel has a PC-assigned ID, it can only receive commands containing the ID. Assign an ID before sending a
command.
Characters that can be used for an ID include, 0 - 9 and A - F (there is not distinction between upper case and lower case
letters).
An ∗(asterisk) can be used as follows:
<∗∗IDC>: Clear the IDs assigned for all panels
<2∗IN1>: The input for which the first digit is 2 is set to INPUT1
Precautions when assigning IDs
Panels connected after a display’s ID has been cleared cannot be operated with RS-232C commands.
When the <∗∗IDC> command is sent, the IDs for all the sets from Set #1 to Set #4 are cleared. Only the first panel,
which is directly connected to the PC, can be controlled.
Send the command <01 IDS> to control the next panel. Continue setting IDs in this way for the remaining panels to
once again control the displays.
Note
When the IDs are set, when one or both of the IDs before a command is sent from the PC is an ∗, there is no echo.
When sending more commands, wait six seconds before sending the next command.
Example) When ∗∗OOO and ∗1OOO or 1∗OOO (OOO is the command) are sent from the PC, operation is performed
but there is no echo.
Set #4
ID = 04
Set #1 Set #2 Set #3
ID = 01
Sent commands:
1<01 IDS>
2<02 IDS>
3<03 IDS>
4<04 IDS>
ID = 02 ID = 03
PC
OUT IN OUT IN OUT IN
‘
‘
‘
±
RS-232C connection

6
Under the connection conditions shown below, use a combination cable for up to 16 panels.
Conditions: 1Length of RS-232C cable connecting PC to Plasma Display: 5 m
2Combination cable length: 5 m each
3Wire specifications for linking cable: Mini Din 6-pin straight (7 strand cable)
For one strand, suitable for AWG28:
Cross-section area = 0.08 mm2
≠
7 strands ×πr2= 7 ×3.14 ×0.062= 0.079 mm2≠0.08 mm2
Note
For details on the number of displays that can be connected in series using the video OUT terminal (INPUT1, 4), refer to
section 2.3, “Controls and Connectors”(pg. 12).
PC
RS-232C
Combination cable 5m
Plasma Display
1
2
3
#
OUT
IN
OUT
IN
OUT
IN
5m
RS-232C Adjustment

7
RS-232C Adjustment
5 List of RS-232C Commands (Command 434CMX = Command 43MXE1 / Command 505CMX =
Command 50MXE10 , 50MXE11 , 50MXE1 , 50MXE1-S / Command 425CMX = Command 42MXE10)
7Normal Operation Related Commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
POWER
POF ++ Turns the power OFF. 
PON ++ Turns the power ON. 
INPUT SELECT
INP ++
Displays the present input.
INPS01 ++
Switches the main screen to INPUT1. 
INPS02 ++
Switches the main screen to INPUT2. 
INPS03 ++
Switches the main screen to INPUT3. 
INPS04 ++
Switches the main screen to INPUT4. 
INPS05 ++
Switches the main screen to INPUT5. 
IN1 ++
Switches the main screen to INPUT1. 
IN2 ++
Switches the main screen to INPUT2. 
IN3 ++
Switches the main screen to INPUT3. 
IN4 ++
Switches the main screen to INPUT4. 
IN5 ++
Switches the main screen to INPUT5. 
SSIS01 ++
Switches the sub screen to INPUT1. 
SSIS02 ++
Switches the sub screen to INPUT2. 
SSIS03 ++
Switches the sub screen to INPUT3. 
SSIS04 ++
Switches the sub screen to INPUT4. 
SSIS05 ++
Switches the sub screen to INPUT5. 
– SWM +Outputs main input to the full screen. 
– SWS +Outputs sub input to the full screen. 
SCREEN SIZE
AST ++
Executes auto-setup. 
SZM ++
Displays the present screen size.
SZMS00 ++
Sets SCREEN SIZE to DOT BY DOT. 
SZMS01 ++
Sets SCREEN SIZE to 4 :3. 
SZMS02 ++
Sets SCREEN SIZE to FULL. 
SZMS03 ++
Sets SCREEN SIZE to ZOOM. 
SZMS05 ++
Sets SCREEN SIZE to WIDE. 
– SZMS06 +Sets SCREEN SIZE to 14:9. 
SZMS09 ++
Sets SCREEN SIZE to UNDERSCAN. 
– SZMS10 +Sets SCREEN SIZE to 2.35:1. 
VIDEO
MTN PMTS00 +Turns video mute to OFF. 
MTY PMTS01 +Turns video mute to ON. 
SLN STLS00 +Cancels FREEZE. 
SLY STLS01 +Sets FREEZE. 
AUDIO
VOL ++
Adjusts audio volume. 000 042 
AMN AMTS00 +Turns audio mute to OFF. 
AMY AMTS01 +Turns audio mute to ON. 
– AUSS01 +Sets the audio source to main. 
– AUSS02 +Sets the audio source to sub. 
MULTI SCREEN
MSC ++
Displays the present multi-screen.
– MSCS00 +Turns MULTI SCREEN to OFF. 
– MSSS01 +Sets the PinP subscreen size to 1. 
– MSSS02 +Sets the PinP subscreen size to 2. 
– MSSS03 +Sets the PinP subscreen size to 3. 
– MSSS04 +Sets the PinP subscreen size to 4. 
MST ++
Displays the present multi-screen type.
MSTS01 ++
Sets the MULTI SCREEN to 2 SCREEN (side by side 1) 
MSTS02 ++
Sets the MULTI SCREEN to PinP (lower right). 
MSTS03 ++
Sets the MULTI SCREEN to PinP (upper right). 
MSTS04 ++
Sets the MULTI SCREEN to PinP (upper left). 
MSTS05 ++
Sets the MULTI SCREEN to PinP (lower left). 

8
RS-232C Adjustment
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
MSTS06 ++
Sets the MULTI SCREEN to PoutP (side by side, 2-L). 
–MSTS08 +
Sets MULTI SCREEN to SWAP (switches between main
and sub screens).

–MSTS09 +
Sets MULTI SCREEN to PoutP (side by side 2-R).

–MSTS10 +
Sets MULTI SCREEN to 2-SCREEN (side by side 3).

–MSTS11 +
Sets MULTI SCREEN to PoutP (side by side 4-L).

–MSTS12 +
Sets MULTI SCREEN to PoutP (side by side 4-R).

SSI ++Displays the present input to the SUB Screen.
FUNCTIONAL LOCK
FCL ++
Displays the present set value of the FUNCTIONAL LOCK.
FCLS00 ++
Cancels FUNCTIONAL LOCK. 
FCLS01 ++
Prohibits operation of buttons on the display. 
FCLS02 ++
Prohibits operation of buttons on the remote control. 
FCLS03 ++
Prohibits operation of buttons on the display/remote control. 
FCLS04 ++
Sets the memory lock 
OSD
DOF ++ Turns off the OSD display that is now displayed.
7“MENU”–“SETUP”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
COLOR TEMP.
CTP ++
Displays the present set value of the color temperature.
CTPS01 ++
Sets the color temperature to LOW. 
CTPS02 ++
Sets the color temperature to MID LOW. 
CTPS03 ++
Sets the color temperature to MIDDLE. 
CTPS04 ++
Sets the color temperature to MID HIGH. 
CTPS05 ++
Sets the color temperature to HIGH. 
DNR
DNR ++
Displays the present set value of the DNR.
DNRS00 ++
Sets digital NR to OFF. 
DNRS01 ++
Sets digital NR to LOW. 
DNRS02 ++
Sets digital NR to MIDDLE. 
DNRS03 ++
Sets digital NR to HIGH. 
MPEG NR
MNR ++
Displays the present set value of the MPEG NR.
MNRS00 ++
Sets MPEG NR to OFF. 
MNRS01 ++
Sets MPEG NR to LOW. 
MNRS02 ++
Sets MPEG NR to MIDDLE. 
MNRS03 ++
Sets MPEG NR to HIGH. 
CTI
CTR ++
Displays the present set value of CTI.
CTRS00 ++
Sets CTI to OFF. 
CTRS01 ++
Sets CTI to ON. 
PURE CINEMA
PUC ++
Displays the present set value of PURE CINEMA.
PUCS00 ++
Sets PURE CINEMA to OFF. 
PUCS01 ++
Sets PURE CINEMA to STANDARD. 
COLOR DECORDING
MCD ++
Displays the present color decoding.
MCDS01 ++
Sets COLOR DECORDING to RGB (VIDEO). 
MCDS02 ++
Sets COLOR DECORDING to COMPONENT1 (YCbCr). 
MCDS03 ++
Sets COLOR DECORDING to COMPONENT2 (YPbPr). 
COLOR SYSTEM
CLS ++
Displays the present set value of the color system.
CLSS01 ++
Sets color system to AUTO. 
CLSS02 ++
Sets color system to NTSC. 
CLSS03 ++
Sets color system to PAL. 
CLSS04 ++
Sets color system to SECAM. 

9
RS-232C Adjustment
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
CLSS05 ++ Sets color system to 4.43NTSC. 
CLSS06 ++ Sets color system to PAL M. 
CLSS07 ++ Sets color system to PAL N. 
SIGNAL FORMAT
SFT ++ Displays the present set value of the SIGNAL FORMAT.
SFTS01 ++ Sets SIGNAL FORMAT to Type1. Note 1
SFTS02 ++ Sets SIGNAL FORMAT to Type2. Note 1
SFTS03 ++ Sets SIGNAL FORMAT to Type3. Note 1
SFTS04 ++ Sets SIGNAL FORMAT to Type4. Note 1
–SFTS05 +Sets SIGNAL FORMAT to Type5. 
–SFTS06 +Sets SIGNAL FORMAT to Type6. 
–SFTS07 +Sets SIGNAL FORMAT to Type7. 
–SFTS08 +Sets SIGNAL FORMAT to Type8. 
–+SFTS09 Sets SIGNAL FORMAT to Type9. New
–+SFTS20 Sets SIGNAL FORMAT to Type10. New
–SFTS10 +Sets SIGNAL FORMAT to AUTO. 
DVI
EDIS01 DSGS01 +Sets the DVI connection signal to PC. Note 2
EDIS02 DSGS02 +Sets the DVI connection signal to STB/DVD. Note 2
–DBLS01 +Sets the DVI BLACK LEVEL to LOW. 
–DBLS02 +Sets the DVI BLACK LEVEL to HIGH. 
Note 1: The operation differs between the PDP-434CMX/PDP-505CMX and PDP-425CMX/PDP-507CMX/PDP-427CMX
Note 2: EDIS01/02 only operates on the PDP-505CMX
7“MENU”–“OPTION”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function Number direct Last
memory Comment
Effective Minimum Maximum
ENERGY SAVE
ESV ++ Displays the present set value of ENERGY SAVE.
ESVS00 ++
Sets ENERGY SAVE to STANDARD (STANDARD1). 
Sets STANDARD1
only on the 507CMX
ESVS01 ++ Sets ENERGY SAVE to save energy. 
ESVS02 ++ Sets ENERGY SAVE to fixed brightness. 
ESVS03 ++ Sets ENERGY SAVE to mode 3 (long service life). 
ESVS04 ++ Sets ENERGY SAVE to AUTO. 
–+ESVS05 Sets ENERGY SAVE to MUTE. New
–+ESVS06 Sets ENERGY SAVE to standard 2. 
New, and effective
only on the 507CMX
TIMER
– TSMS00 +Turns summer time to OFF. 
– TSMS01 +Turns summer time to ON. 
– TPH +Sets the hour of the present time. 000 023 
000 – 023: Set by
24-hour clock time
– TPM +Sets the minute of the present time. 000 059 000 – 059: Set
for 60 minutes
– TPW +Sets the day of week of the present time. 001 007 001: Monday –
007; Saturday
– TPTS00 +Sets PROGRAM TIMER/REPEAT TIMER to OFF. 
– TPTS01 +Sets PROGRAM TIMER to ON. 
–+TPTS02 Sets REPEAT TIMER to ON. New
ORBITER
OMN ORBS00 +Sets the ORBITER to OFF. 
OMY ORBS01 +Sets the ORBITER to ON (AUTO1). 
– ORBS02 +Sets the ORBITER to ON (AUTO2). 
– ORBS03 +Sets the ORBITER to ON (AUTO3). 
SOFT FOCUS
– SOFS00 +Sets SOFT FOCUS to OFF. 
– SOFS01 +Sets SOFT FOCUS to 1. 
– SOFS02 +Sets SOFT FOCUS to 2. 
– SOFS03 +Sets SOFT FOCUS to 3. 
– SOFS04 +Sets SOFT FOCUS to 4. 
SUB SCREEN FREEZE
– SSTS00 +Sets SUB SCREEN FREEZE to OFF. 
– SSTS01 +Sets SUB SCREEN FREEZE to SIDE BY SIDE. 
– SSTS02 +Sets SUB SCREEN FREEZE to PinP. 

10
RS-232C Adjustment
7“INTEGRATOR”–“PICTURE”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
VIDEO QUALITY
CNT ++
Adjusts the contrast. 000 255 
BRT ++
Adjusts the brightness. 000 255 
ENH ++
Adjusts the horizontal enhance. 000 015 
ENV ++
Adjusts the vertical enhance. 000 015 
COL ++
Adjusts the color. 000 127 
TNT ++
Adjusts the tint. 000 060 
SHP ++
Adjusts the sharpness. 000 015 
WHITE BALANCE
RHI ++
Adjusts R.HIGH of the white balance. 000 255 
GHI ++
Adjusts G.HIGH of the white balance. 000 255 
BHI ++
Adjusts B.HIGH of the white balance. 000 255 
GLW ++
Adjusts G.LOW of the white balance. 000 255 
RLW ++
Adjusts R.LOW of the white balance. 000 255 
BLW ++
Adjusts B.LOW of the white balance. 000 255 
COLOR DETAIL
CGR ++
Adjusts color detail red. 000 060 
CGY ++
Adjusts color detail yellow. 000 060 
CGG ++
Adjusts color detail green. 000 060 
CGC ++
Adjusts color detail cyan. 000 060 
CGB ++
Adjusts color detail blue. 000 060 
CGM ++
Adjusts color detail magenta. 000 060 
GAMMA
GRA ++
Displays the present set value of gradation.
–GRAS18 +Sets gradation GAMMA 1.8. 
–GRAS19 +Sets gradation GAMMA 1.9. 
–GRAS20 +Sets gradation GAMMA 2.0. 
–GRAS21 +Sets gradation GAMMA 2.1. 
–GRAS22 +Sets gradation GAMMA 2.2. 
–GRAS23 +Sets gradation GAMMA 2.3. 
–GRAS24 +Sets gradation GAMMA 2.4. 
PRESET
STD ++
Restores the PICTURE, W/B adjustment value of the integrator
to the initial values. 
7“INTEGRATOR”–“SCREEN”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
POSITION
HPS ++
Adjusts the horizontal position. 000 255 
VPS ++
Adjusts the vertical position. 000 255 
CLOCK/PHASE
CFR ++
Adjusts the CLOCK (PLL frequency). 000 255 
CPH ++
Adjusts the PHASE (PLL phase). 000 031 
SIZE
HSI ++
Adjusts the horizontal size. 000 064 
VSI ++
Adjusts the vertical size. 000 064 
PRESET
FRP ++
Restores the SCREEN adjustment value of the integrator to the
initial values. 
7“INTEGRATOR”–“SETUP”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
SUB VOLUME
SVL ++ Adjusts the SUB VOLUME. 000 020 

11
RS-232C Adjustment
7“INTEGRATOR”–“OPTION”related commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
SCREEN MASK
FMK ++
Displays the present set value of SCREEN MASK.
FMKS00 ++
Sets SCREEN MASK to OFF. 
FMKS02 ++
Sets SCREEN MASK to inverse (negative –positive reversed). 
FMKS03 ++
Sets SCREEN MASK to white mask. 
FMKS04 ++
Sets SCREEN MASK to red mask. 
FMKS05 ++
Sets SCREEN MASK to green mask. 
FMKS06 ++
Sets SCREEN MASK to blue mask. 
FMKS07 ++
Sets SCREEN MASK to yellow mask. 
SIDE MASK
RSL ++
Adjusts side mask RED. 000 255 
GSL ++
Adjusts side mask GREEN. 000 255 
BSL ++
Adjusts side mask BLUE. 000 255 
–+SMAS00 Sets AUTO SIDE MASK to OFF. New
–+SMAS01 Sets AUTO SIDE MASK to ON. New
VIDEO WALL
MGF ++Displays the set value of VIDEO WALL.
MGFS00 ++Sets VIDEO WALL to OFF. 
–MGFS11 +Sets VIDEO WALL to DIVIDER:1. 
–MGFS12 +Sets VIDEO WALL to DIVIDER:4. 
–MGFS13 +Sets VIDEO WALL to DIVIDER:9. 
–MGFS14 +Sets VIDEO WALL to DIVIDER:16. 
–MGFS15 +Sets VIDEO WALL to DIVIDER:25. 
MGP ++
Displays the present VIDEO WALL (accounting/not accounting
for expanded position/joints) setting.
MGPSnn ++
nn=01 to 04: Sets display position during DIVIDER=2 x 2 (not
accounting for joints). 
nn=05 to 08: Sets display position during DIVIDER=2 x 2
(accounting for joints). 
nn=10 to 18: Sets display position during DIVIDER=3 x 3 (not
accounting for joints). 
nn=20 to 28: Sets display position during DIVIDER=3 x 3
(accounting for joints). 
nn=30 to 3F: Sets display position during DIVIDER=4 x 4 (not
accounting for joints). 
nn=40 to 4F: Sets display position during DIVIDER=4 x 4
(accounting for joints). 
nn=50 to 68: Sets display position during DIVIDER=5 x 5 (not
accounting for joints). 
nn=70 to 88: Sets display position during DIVIDER=5 x 5
(accounting for joints). 
–IDA +Executes AUTO ID setting. 
–PDES00 +Sets POWER ON DELAY mode to OFF. 
–PDES01 +
Sets POWER ON DELAY mode to ON (other than cases used for
a higher than 16 screen system) or mode 1 (used for a higher
than 16 screen system).

–PDES02 +Sets POWER ON DELAY mode 2 (used for a higher than 16
screen system).

–LNKS00 +Sets ABL link to OFF. 
–LNKS01 +Sets ABL link to ON. 
RS-232C
BRA ++
Displays the present set value of baud rate.
BRAS01 ++
Sets the RS-232C baud rate to 1200 bps. 
BRAS02 ++
Sets the RS-232C baud rate to 2400 bps. 
BRAS03 ++
Sets the RS-232C baud rate to 4800 bps. 
BRAS04 ++
Sets the RS-232C baud rate to 9600 bps. 
BRAS05 ++
Sets the RS-232C baud rate to 19200 bps. 
BRAS06 ++
Sets the RS-232C baud rate to 38400 bps. 
ID NUMBER
IDC ++
Clears the ID number. 
IDS ++
Sets the ID number. 

12
RS-232C Adjustment
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
FAN
FCM ++
Maximizes fan rotation control. 
FCA ++
Automates fan rotation control. 
––FCU Sets integrator’s fan rotation control maximum to apply a
brightness 
New, and effective
only on the 507CMX
OSD
DIN OSDS00 +Sets OSD display to OFF. 
DIY OSDS01 +Sets OSD display to ON. 
–OSSS01 +Displays expanded OSD. 
–OSSS02 +Displays contracted OSD. 
–OSAS01 +Sets the OSD display angle to horizontal. 
–OSAS02 +Sets the OSD display angle to vertical. 
FRONT INDICATOR
LEN LESS00 +Sets the FRONT INDICATOR to OFF. 
LEY LESS01 +Sets the FRONT INDICATOR to ON. 
COLOR MODE
CM1 CLMS00 +Sets the COLOR MODE to NORMAL. 
CM2 CLMS01 +Sets the COLOR MODE to STUDIO. 
UNDER SCAN
USCS00 ++
Sets the UNDERSCAN setting to OFF. 
USCS01 ++
Sets the UNDERSCAN setting to ON. 
USC ++
Displays the present set value of UNDERSCAN.
IMAGE PROCESS
–IPR +Obtains the present IMAGE PROCESS setting.
–IPRS01 +Sets the IMAGE PROCESS to NORMAL. 
–IPRS02 +Sets the IMAGE PROCESS to PURE. 
–IPRS03 +Sets the IMAGE PROCESS to MONOTONE. 
–IPRS04 +Sets the IMAGE PROCESS to HIGH CONTRAST. 
––IPRS05 Sets the IMAGE PROCESS to BLUE ONLY. New
FRC
FRC ++
Displays the present set value of FRC.
–FRCS00 +Sets the FRC to OFF. 
FRCS01 ++
Sets the FRC to ON. Note 1
SEAMLESS INPUT SWITCH
–SLSS00 +Sets the SEAMLESS INPUT SWITCH mode to OFF. 
–SLSS01 +Sets the SEAMLESS INPUT SWITCH mode to ON. 
–SL1S01 +Sets the SEAMLESS SW SELECT 1 to INPUT1. 
–SL1S02 +Sets the SEAMLESS SW SELECT 1 to INPUT2. 
–SL1S03 +Sets the SEAMLESS SW SELECT 1 to INPUT3. 
–SL1S04 +Sets the SEAMLESS SW SELECT 1 to INPUT4. 
–SL1S05 +Sets the SEAMLESS SW SELECT 1 to INPUT5. 
–SL2S01 +Sets the SEAMLESS SW SELECT 2 to INPUT1. 
–SL2S02 +Sets the SEAMLESS SW SELECT 2 to INPUT2. 
–SL2S03 +Sets the SEAMLESS SW SELECT 2 to INPUT3. 
–SL2S04 +Sets the SEAMLESS SW SELECT 2 to INPUT4. 
–SL2S05 +Sets the SEAMLESS SW SELECT 2 to INPUT5. 
MIRROR
MIRS00 ++ Sets mirror mode to OFF (normal display). 
MIRS01 ++ Performs left-right reversal with MIRROR MODE. 
MIRS02 ++ Performs up-down reversal with MIRROR MODE. 
MIRS03 ++ Performs up-down left-right reversal with MIRROR MODE. 
MULTI SCREEN
–PTRS00 +Sets sub screen translucence to OFF (0%). 
–PTRS01 +Sets sub screen translucence to 10 %. 
–PTRS02 +Sets sub screen translucence to 20 %. 
–PTRS03 +Sets sub screen translucence to 30 %. 
–PTRS04 +Sets sub screen translucence to 40 %. 
–PTRS05 +Sets sub screen translucence to 50 %. 
–PTRS06 +Sets sub screen translucence to 60 %. 
–PTRS07 +Sets sub screen translucence to 70 %. 
–PTRS08 +Sets sub screen translucence to 80 %. 
Note 1: The operation differs between the PDP-434CMX/PDP-505CMX and PDP-425CMX/PDP-507CMX/PDP-427CMX

13
RS-232C Adjustment
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
–BPIS01 +Sets the BANNER PinP input to INPUT1. 
–BPIS02 +Sets the BANNER PinP input to INPUT2. 
–BPPS00 +Sets the BANNER PinP setting to OFF. 
–BPPS01 +Sets the BANNER PinP setting to TOP3. 
–BPPS02 +Sets the BANNER PinP setting to MID-HIGH. 
–BPPS03 +Sets the BANNER PinP setting to MID-LOW. 
–BPPS04 +Sets the BANNER PinP setting to BOTTOM3. 
–+BPPS05 Sets the BANNER PinP setting to TOP2. New
–+BPPS06 Sets the BANNER PinP setting to BOTTOM2. New
–+BPPS07 Sets the BANNER PinP setting to TOP1. New
–+BPPS08 Sets the BANNER PinP setting to BOTTOM1. New
–+BPPS09 Sets the BANNER PinP setting to LEFT. New
–+BPPS10 Sets the BANNER PinP setting to RIGHT. New
–+PFAS00 PIP fade in function ineffective. New
–+PFAS01 PIP fade in function effective. New
–+PFAS10 PIP fade in (only when PIP fade in function is effective). New
–+PFAS11 PIP fade off (only when PIP fade in function is effective). New
FUNCTION
FDT ++
Executes FUNCTION DEFAULT. 
7Other commands
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
DISPLAY CALL
–DITS01 +Displays DISPLAY CALL 1.
–DITS02 +Displays DISPLAY CALL 2.
–IM0 +INFORMATION write-in (1-3 characters). 
–IM1 +INFORMATION write-in (4-6 characters). 
–IM2 +INFORMATION write-in (7-9 characters). 
–IM3 +INFORMATION write-in (10-12 characters). 
–IM4 +INFORMATION write-in (13-15 characters). 
–IM5 +INFORMATION write-in (16-18 characters). 
–IM6 +INFORMATION write-in (19-21 characters). 
–IMD +Clears INFORMATION. 
AUXILIARY COMMAND
DW0 ++Subtracts 10 from the adjustment value.
DWF ++Minimizes the adjustment value.
DWn ++Subtracts n from the adjustment value. (n=1~9)
UP0 ++Adds 10 to the adjustment value.
UPF ++Maximizes the adjustment value.
UPn ++Adds n to the adjustment value (n = 1 to 9).
GST QST +Obtains status information.
GPI QPI +Obtains integrator/PICTURE information.
GWB QWB +Obtains integrator/WHITE BALANCE information.
GPS QPS +Obtains integrator/SCREEN information.
GSS QSS +Obtains SETUP information.
GSO QSO +Obtains Menu Integrator/OPTION information.
–QAP +Obtains various machine names.
–QCI +Obtains time information.
–QSU +Obtains audio status.
OTHER
––MRKS00 Sets mark display off. New
––MRKS01 Sets mark display on. New
––RMCS10 Remote control key: CURSOR RIGHT New
––RMCS11 Remote control key: CURSOR LEFT New
––RMCS12 Remote control key: CURSOR UP New
––RMCS13 Remote control key: CURSOR DOWN New
––RMCS14 Remote control key: SET New
––RMCS25 Remote control key: MENU New

14
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
––RMCS26 Remote control key: POINT ZOOM New
––RMCS27 Remote control key: ID NO SET New
––RMCS28 Remote control key: CLEAR New
––RMCS29 Remote control key: FREEZE New
––RMCS30 Remote control key: STANDBY/ON New
––RMCS31 Remote control key: VOLUME UP New
––RMCS32 Remote control key: VOLUME DOWN New
––RMCS33 Remote control key: MUTING New
––RMCS34 Remote control key: SCREEN SIZE New
––RMCS35 Remote control key: SPLIT New
––RMCS36 Remote control key: SUB INPUT New
––RMCS37 Remote control key: PIP SHIFT New
RS-232C Adjustment

15
6 QUEST Commands
What are QUEST commands?
•Quest commands output TXD such as adjustment data from the panel’s microprocessor to a PC.
•Adjustment and other data is output in ASCII code.
Note
Command names are given inside brackets < >.
•Data output format
Note
•A QUEST command is invalid when no ID has not been assigned.
•A QUEST command is invalid when a wildcard (*) is used in the ID when sending the command.
7Quest Command Table
STX (02hex) Command
(3 Byte) Data ···· Data ETX (03hex)
Checksum
(2 Byte)
RS-232C Adjustment
Command
434CMX
505CMX
Command
425CMX
Command
427CMX
507CMX
Function
Number direct Last
memory Comment
Effective Minimum Maximum
GST QST +Obtains status information.
GPI QPI +Obtains integrator/PICTURE information.
GWB QWB +Obtains integrator/WHITE BALANCE information.
GPS QPS +Obtains integrator/SCREEN information.
GSS QSS +Obtains SETUP information.
GSO QSO +Obtains Menu Integrator/OPTION information.
–QAP +Obtains audio status.
–QCI +Obtains time information.
–QSU +Obtains various machine names.

16
RS-232C Adjustment
1) Obtaining QST Status Information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QST (fixed)
3 Generation information 1 Byte 5 (fixed)
4 Inch information 1 Byte 4: 42 inch 5: 50 inch
5 Forwarding 1 Byte M (fixed)
6 Power source state 1 Byte S: Standby status P: Power supplied status
7 During standby: Standby cause 1 Byte N: Normal standby time
W: Standby time based on POWER MANAGEMENT
S: Standby time based on SD or PD
During power supply: main screen signal status N: normal signal input time
L: no signal input time
O: OUT OF RANGE signal input time
8 During standby or 1 screen display: dummy data 1 Byte
During 2-screen display: sub screen signal status N: normal signal input time
L: no signal input time
O: OUT OF RANGE signal input time
9 Main input function information 3 Byte IN1: INPUT1 IN2: INPUT2 IN3: INPUT3 IN4: INPUT4
IN5: INPUT5
10 Sub input function information 3 Byte IN1: INPUT1 IN2: INPUT2 IN3: INPUT3 IN4: INPUT4
IN5: INPUT5 Note1)
11 Main screen size information 1 Byte 0: DOT BY DOT 1: 4:3 2: FULL 3: ZOOM 5: WIDE 6: 14:9
9: UNDERSCAN A: 2.35:1
12 Two-screen display state 1 Byte 0: OFF (1 screen) 1: SIDE BY SIDE 1
2: PinP (lower right) 3: PinP(upper right)
4: PinP (upper left) 5: PinP(lower left)
6: SIDE BY SIDE 2-L 9: SIDE BY SIDE 2-R
A: SIDE BY SIDE 3 B: SIDE BY SIDE 4-L
C:SIDE BY SIDE 4-R
13 Functional lock information 1 Byte 0: LOCK OFF 1: BUTTONS LOCK 2: IR LOCK
2: IR LOCK 3: IR&BUTTONS LOCK
4: MEMORY LOCK
14 Temperature information 1 (interior) 3 Byte Temperature inside the set (Centigrade) Note 2)
15 Temperature information 2 (outside air) 3 Byte Outside air temperature (Celsius) Note 2)
16 Temperature information 3 (SLOT) 3 Byte SLOT temperature (Celsius) Note 2)
17 Serial No. 15 Byte 15 digit character string
18 Dummy data 3 Byte
19 Dummy data 2 Byte
20 HOUR METER 5 Byte 5 digit number
21 Check sum 2 Byte
22 ETX 1 Byte 03hex
Note 1) During standby and during a single screen display, the unit outputs the value that is in memory.
Note 2) During standby and immediately after POWER ON, the correct value is not output.
In this case, please obtain the information after waiting a short period of time after POWER ON.
These types of information are output as reference information (these are not guaranteed information).
Normally refer to temperature information 3.

17
RS-232C Adjustment
2) <QPI> Obtaining Integrator/PICTURE information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QPI (fixed)
3 CONTRAST 3 Byte 000 to 255 Note 1)
4 BRIGHTNESS 3 Byte 000 to 255 Note 1)
5 C,DETAIL R (RED) 3 Byte 000 to 060 Note 1)
6 C,DETAIL Y (YELLOW) 3 Byte 000 to 060 Note 1)
7 C,DETAIL G (GREEN) 3 Byte 000 to 060 Note 1)
8 C,DETAIL C (CYAN) 3 Byte 000 to 060 Note 1)
9 C,DETAIL B (BLUE) 3 Byte 000 to 060 Note 1)
10 C,DETAIL M (MAGENTA) 3 Byte 000 to 060 Note 1)
11 H.ENHANCE 3 Byte 000 to 015 Note 1), Note 2)
12 V.ENHANCE 3 Byte 000 to 015 Note 1), Note 2)
13 COLOR 3 Byte 000 to 127 Note 1), Note 3)
14 TINT 3 Byte 000 to 060 Note 1), Note 3)
15 SHARPNESS 3 Byte 000 to 015 Note 1), Note 3)
16 Main input function 3 Byte Same as item 9 of QST commands
17 Main screen size information 1 Byte Same as item 11 of QST commands
18 Check sum 2 Byte
19 ETX 1 Byte 03hex
Note 1) If the signal type is not confirmed, dummy data is output.
Note 2) During video signal input, dummy data is output.
Note 3) During PC signal input, dummy data is output.
3) <QWB> Obtaining integrator/WHITE BALANCE information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QWB (fixed)
3 R.HIGH 3 Byte 000 to 255 Note 1)
4 G.HIGH 3 Byte 000 to 255 Note 1)
5 B.HIGH 3 Byte 000 to 255 Note 1)
6 R.LOW 3 Byte 000 to 255 Note 1)
7 G.LOW 3 Byte 000 to 255 Note 1)
8 B.LOW 3 Byte 000 to 255 Note 1)
9 Main input function 3 Byte Same as item 9 of QST commands
10 Main screen size 1 Byte Same as item 11 of QST commands
11 Check sum 2 Byte
12 ETX 1 Byte 03hex
Note 1) If the signal type is not confirmed, dummy data is output.
4) <QPS> Obtaining integrator/SCREEN information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QPS (fixed)
3 H.POSITION 3 Byte 000 to 255 Note 1)
4 V.POSITION 3 Byte 000 to 255 Note 1)
5 H.SIZE 3 Byte 000 to 064 Note 1)
6 V.SIZE 3 Byte 000 to 064 Note 1)
7 CLOCK 3 Byte 000 to 255 Note 1), Note 2)
8 PHASE 3 Byte 000 to 031 Note 1), Note 2)
9 Main input function 3 Byte Same as item 9 of QST commands
10 Main screen size information 1 Byte Same as item 11 of QST commands
18 Check sum 2 Byte
19 ETX 1 Byte 03hex
Note 1) If the signal type is not confirmed, dummy data is output.
Note 2) During DVI or video input, dummy data is output.

18
RS-232C Adjustment
5) <QSS> Obtaining SETUP information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QSS (fixed)
3 COLOR TEMP. 1 Byte 1: LOW 2: MID LOW 3: MIDDLE 4: MID HIGH
5: HIGH Note 1)
4 POWER MGT. 1 Byte 0: OFF 1: ON
5 AUTO POWER OFF 1 Byte 0: DISABLE 1: ENABLE
6 DNR 1 Byte 0: OFF 1: LOW 2: MIDDLE 3: HIGH Note 1)
7 MPEG NR 1 Byte 0: OFF 1: LOW 2: MIDDLE 3: HIGH Note 1)
8 CTI 1 Byte 0: OFF 1: ON Note 1)
9 PURECINEMA 1 Byte 0: OFF 1: ON Note 1)
10 COLOR DECODING 1 Byte 1: RGB 2: COMP1 3: COMP2 Note 1)
11 COLOR SYSTEM 1 Byte 1: AUTO 2: NTSC 3: PAL 4: SECAM 5: 4.43NTSC
6: PAL M 7: PAL N Note 1)
12 DVI SET UP (PLUG/PLAY) 1 Byte 1: PC 2: VIDEO Note 1)
13 DVI SET UP (BLACK LEVEL) 1 Byte 1: LOW 2: HIGH Note 1)
14 BRT.ENHANCE 1 Byte 0: OFF 1: ON Note 1)
15 SUB VOLUME 2 Byte 00 to 20
16 Main input function 3 Byte Same as item 9 of QST commands
17 Main screen size information 1 Byte Same as item 11 of QST commands
18 Check sum 2 Byte
19 ETX 1 Byte 03hex
Note 1) In the case of set data that cannot be output because of the type of input signal, dummy data is output.
6) <QSO> Obtaining menu integrator/OPTION information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QSO (fixed)
3 ENERGY SAVE 1 Byte 0: STANDARD1 1: MODE1 2: MODE2 3: MODE3
4: AUTO 5: MUTE 6: STANDARD2
4 PROGRAM/REPEAT timer 1 Byte 0: OFF 1: PROGRAM 2: REPEAT
5 SCREEN MANAGEMENT (ORBITER) 1 Byte 0: OFF 1: MODE1 2: MODE2 3: MODE3
6 SCREEN MANAGEMENT (SOFT FOCUS) 1 Byte 0: OFF 1: 1 2: 2 3: 3 4: 4
7 AUTO SETUP MODE 1 Byte 0: INACTIVE 1: ACTIVE
8 AUTO FUNCTION 1 Byte 0: OFF 1: INPUT1 2: INPUT4
9 PIP DETECT 1 Byte 0: INACTIVE 1: ACTIVE
10 SPLIT FREEZE 1 Byte 0: OFF 1: SIDE BY SIDE 2: PIP
11 SCREEN MASK 1 Byte 0: OFF 2: INVERSE 3: WHITE 4: RED 5: GREEN 6: BLUE
7: YELLOW
12 SIDE MASK R-LEVEL 3 Byte 000 to 255
13 SIDE MASK G-LEVEL 3 Byte 000 to 255
14 SIDE MASK B-LEVEL 3 Byte 000 to 255
15 VIDEO WALL (MODE) 1 Byte 0: OFF 1: 1 screen 2: 4 screens (2 x 2) 3: 9 screens (3 x 3)
4: 16 screens (4 x 4) 5: 25 screens (5 x 5)
16 VIDEO WALL (POSITION) 2 Byte 01 to 56
17 VIDEO WALL (TYPE) 1 Byte 0: NORMAL 1: ADJUSTED
18 VIDEO WALL (POWER ON DELAY) 1 Byte 0: OFF 1: ON 2: MODE1 3: MODE2
19 VIDEO WALL (ABL LINK) 1 Byte 0: OFF 1: ON
20 Spare (dummy) 1 Byte * (FIX)
21 FAN CONTROL 1 Byte 1: AUTO 2: MAX
22 OSD DISPLAY 1 Byte 0: OFF 1: ON
23 OSD SIZE 1 Byte 0: LARGE 1: SMALL
24 OSD ANGLE 1 Byte 0: H 1: V
25 FRONT INDICATOR 1 Byte 0: OFF 1: ON
26 COLOR MODE 1 Byte 1: NORMAL 2: STUDIO

19
RS-232C Adjustment
Sequence Data Content Size Remarks
27 PRO USE UNDERSCAN 1 Byte 0: OFF 1: ON
28 PRO USE IMAGE PROCESS 1 Byte 1: NORMAL 2: PURE 3: MONOTONE 4: BLUE ONLY
5: HIGH CONTRAST
29 PRO USE SYGNAL TYPE 1 Byte 1: MOTION 2: STILL 3: NONE STD
30 FRC 1 Byte 0: OFF 1: ON
31 POWER ON MODE INPUT 1 Byte See the table below.
32 POWER ON MODE MULTI MODE 1 Byte See the table below.
33 POWER ON MODE MULTI INPUT 1 1 Byte 1: INPUT 2: INPUT2 3: INPUT3 4: INPUT4 5: INPUT5
34 POWER ON MODE MULTI INPUT 2 1 Byte 1: INPUT 2: INPUT2 3: INPUT3 4: INPUT4 5: INPUT5
35 POWER ON MODE VOLUME 2 Byte 0 to 42: In the case of last memory, FF
36 SEAMLESS SW 1 Byte 0: OFF 1: ON
37 SEAMLESS SW SELECT1 1: INPUT 2: INPUT2 3: INPUT3 4: INPUT4 5: INPUT5
38 SEAMLESS SW SELECT2 1 Byte 1: INPUT 2: INPUT2 3: INPUT3 4: INPUT4 5: INPUT5
39 MIRROR MODE 1 Byte 0: OFF 1: X 2: Y 3: XY
40 MULTI SCREEN SET (S BY S SIZE) 1 Byte 1: NORMAL 2: FULL
41 MULTI SCREEN SET (S BY S LAYOUT) 1 Byte 1: MODE1 2: MODE2 3: MODE3
42 MULTI SCREEN SET (PIP SIZE) 1 Byte 1: 1 (SMALL) to 4: 4 (LARGE)
43 MULTI SCREEN SET (TRANSLUCENT) 1 Byte 0: OFF 1: 10 % 2: 20 % 3: 30 % 4: 40 % 5: 50 %
6: 60 % 7: 70 % 8: 80 %
44 MULTI SCREEN SET (BANNER PIP) 1 Byte 0: OFF 1: BOTTOM1 2: BOTTOM2 3: BOTTOM3
4: MID LOW 5: MID HIGH 6: TOP3 7: TOP2 8: TOP1
9: LEFT A: RIGHT
45 MULTI SCREEN SET (BANNER INPUT) 1 Byte 1: INPUT1 2: INPUT2
46 Main input function 3 Byte Input functions of the main screen (refer to the following table for
details)
47 Main screen size information 1 Byte Main screen size (refer to the following table for details)
48 Check sum 2 Byte
49 ETX 1 Byte 03hex
Input functions INPUT
(response)
1 SIDE BY SIDE1
2 SIDE BY SIDE2
3 SIDE BY SIDE3
4 BOTTOM LEFT
5 BOTTOM RIGHT
6 TOP RIGHT
7 TOP LEFT
Input functions INPUT
(response)
0 LAST
1 INPUT1
2 INPUT2
3 INPUT3
4 INPUT4
5 INPUT5
A MULTI
Input function Input
IN1 INPUT1
IN2 INPUT2
IN3 INPUT3
IN4 INPUT4
IN5 INPUT5
* * * Unconfirmed (standby time)
7POWER ON MODE INPUT 7POWER ON MODE MULTI MODE
7Main screen input function
Main screen size Screen size
0 DOT BY DOT
1 4 : 3
2 FULL
3 ZOOM
5 WIDE
6 14 : 9
9 UNDER SCAN
A 2.35 : 1
7Main screen size

20
RS-232C Adjustment
9) <QAP> Obtaining machine name
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QAP (fixed)
3 Machine name information 18 Byte 42 inch:
A (North America model): PDP-427CMX********
G (Europe-general model): PDP-42MXE20*******
50 inch:
J (Japan model): PDP-507CMX-JP*****
A (North America model): PDP-507CMX********
G (Europe-general/CKD model): PDP-50MXE20*******
GS (Europe-general/silver model): PDP-50MXE20*******
4 Check sum 2 Byte
5 ETX 1 Byte 03hex
7) <QSU> obtaining the audio status
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QSU (fixed)
3 Main volume 3 Byte 000 to 042
4 Audio mute status 1 Byte 0: OFF 1: ON
5 INPUT1 sub volume 3 Byte 000 to 020
6 INPUT2 sub volume 3 Byte 000 to 020
7 INPUT3 sub volume 3 Byte 000 to 020
8 INPUT4 sub volume 3 Byte 000 to 020
9 INPUT5 sub volume 3 Byte 000 to 020
10 Check sum 2 Byte
11 ETX 1 Byte 03hex
8) <QCI> Obtaining time information
Sequence Data Content Size Remarks
1 STX 1 Byte 02hex
2 Command echo-back 3 Byte QCI (fixed)
3 Time information 2 Byte Hour (24 hour system) 00 to 23 Note 1)
2 Byte Minute 00 to 59 Note 1)
2 Byte Second 00 to 59 Note 1)
4 Dummy data 8 Byte
5 Day of week 1 Byte 1: Sunday 2: Monday 3: Tuesday 4: Wednesday
5: Thursday 6: Friday 7: Saturday Note 1)
6 Check sum 2 Byte
7 ETX 1 Byte 03hex
Note 1) During standby and when this command was initially set, the value at the time that power was finally shut off is transmitted.