Pioneer PDP505CMX - HD Plasma Display User manual
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
ARP3305
T – ZZY OCT. 2005 Printed in Japan
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
PDP-505CMX LUC5 AC100 - 120V
PDP-505CMX
PLASMA DISPLAY
¶This service manual should be used together with the following manual(s):
Model No. Order No. Remarks
SAFETY INFORMATION, EXPLODED VIEWS AND PARTS LIST , BLOCK DIAGRAM,
PCB PARTS LIST, ADJUSTMENT, IC INFORMATION etc.
ARP3242 SCHEMATIC DIAGRAM and PCB CONNECTION DIAGRAM
PDP-504CMX/LUC/1 ARP3241
CONTENTS
SAFETY INFORMATION ........................................................................... 2
1. CANCELING DETECTION BY THE TRAP SWITCH ............................. 5
2. CONTRAST OF MISCELLANEOUS PARTS ......................................... 6
3. SCHEMATIC DIAGRAM ........................................................................ 12
3.1 OVERALL WIRING DIAGRAM .........................................................12
4. PCB CONNECTION DIAGRAM ............................................................. 22
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
2
A
B
C
D
1234
1234
PDP-505CMX
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely,
you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts
must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
SAFETY PRECAUTIONS
NOTICE : Comply with all cautions and safety related notes
located on or inside the cabinet and on the chassis.
The following precautions should be observed :
1. When service is required, even though the PDP UNIT an
isolation transformer should be inserted between the power line
and the set in safety before any service is performed.
2. When replacing a chassis in the set, all the protective devices
must be put back in place, such as barriers, nonmetallic knobs,
adjustment and compartment covershields, isolation resistor-
capacitor, etc.
3. When service is required, observe the original lead dress. Extra
precaution should be taken to assure correct lead dress in the
high voltage circuitry area.
4. Always use the manufacture's replacement components.
Especially critical components as indicated on the circuit
diagram should not be replaced by other manufacture's.
Furthermore where a short circuit has occurred, replace those
components that indicate evidence of overheating.
5. Before returning a serviced set to the customer, the service
technician must thoroughly test the unit to be certain that it is
completely safe to operate without danger of electrical shock,
and be sure that no protective device built into the set by the
manufacture has become defective, or inadvertently defeated
during servicing. Therefore, the following checks should be
performed for the continued protection of the customer and
servicetechnician.
6. Perform the following precautions against unwanted radiation
and rise in internal temperature.
• Always return the internal wiring to the original styling.
• Attach parts (Gascket, Ferrite Core, Ground, Rear Cover,
Shield Case etc.) surely after disassembly.
7. Perform the following precautions for the PDP panel.
• When the front case is removed, make sure nothing hits the
panel face, panel corner, and panel edge (so that the glass does
not break).
• Make sure that the panel vent does not break. (Check that the
cover is attached.)
• Handle the FPC connected to the panel carefully.
Twisting or pulling the FPC when connecting it to the
connector will cause it to peel off from the panel.
8. Pay attention to the following.
• When the front case is removed, infrared ray is radiated and
may disturb reception of the remote control unit.
• Pay extreme caution when the front case and rear panel are
removed because this may cause a high risk of disturbance to
TVs and radios in the surrounding.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
3
A
B
C
D
5678
5678
PDP-505CMX
Leakage Current Cold Check
With the AC plug removed from an AC power source, place a
jumper across the two plug prongs. Turn the AC power switch on.
Using an insulation tester (DC 500V), connect one lead to the
jumpered AC plug and touch the other lead to each exposed metal
part (input/output terminals, screwheads, metal overlays, control
shafts, etc.), particularly any exposed metal part having a return
path to the chassis. Exposed metal parts having a return path to
the chassis should have a minimum resistor reading of 0.3MΩ
and a maximum resistor reading of 5MΩ. Any resistor value
below or above this range indicates an abnormality which
requires corrective action. Exposed metal parts not having a
return path to the chassis will indicate an open circuit.
Leakage Current Hot Check
Plug the AC line cord directly into an AC power source (do not
use an isolation transformer for this check).
Turn the AC power switch on.
Using a "Leakage Current Tester (Simpson Model 229
equivalent)", measure for current from all exposed metal parts of
the cabinet (input/output terminals, screwheads, metal overlays,
control shaft, etc.), particularly any exposed metal part having a
return path to the chassis, to a known earth ground (water pipe,
conduit, etc.). Any current measured must not exceed 0.5mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE SET TO THE CUSTOMER.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in PIONEER set have
special safety related characteristics. These are often not evident
from visual inspection nor the protection afforded by them
necessarily can be obtained by using replacement components
rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in this
Service Manual.
Electrical components having such features are identified by
marking with a on the schematics and on the parts list in this
Service Manual.
The use of a substitute replacement component which dose not
have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in this
Service Manual, may create shock, fire or other hazards.
Product Safety is continuously under review and new instructions
are issued from time to time. For the latest information, always
consult the current PIONEER Service Manual. A subscription to,
or additional copies of, PIONEER Service Manual may be
obtained at a nominal charge from PIONEER.
Leakage
current
tester
Reading should
not be above
0.5mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
4
A
B
C
D
1234
1234
PDP-505CMX
Fig.1 Charged Section and High Voltage Generating Point (Rear view)
Charged Section
The places where the commercial AC power is used without
passing through the power supply transformer.
If the places are touched, there is a risk of electric shock. In
addition, the measuring equipment can be damaged if it is
connected to the GND of the charged section and the GND of the
non-charged section while connecting the set directly to the
commercial AC power supply. Therefore, be sure to connect the
set via an insulated transformer and supply the current.
1. Power Cord
2. AC Inlet with Filter
3. Power Switch (S1)
4. Fuse (In the POWER SUPPLY Unit)
5. STB Transformer and Converter Transformer
(In the POWER SUPPLY Unit)
6. Other primary side of the POWER SUPPLY Unit
High Voltage Generating Point
The places where voltage is 100 V or more besides the live parts
are described above. You must not touch them, since there is risk
of electric shock.
The VSUS voltage remains for several minutes after the power to
the unit is turned off. These places must not be touched until
about 10 minutes after the power is turned off, or it is confirmed
with a tester that there is no residual VSUS voltage.
1. POWER SUPPLY Unit.....................................................(223V)
2. 50 X DRIVE Assy ...........................................(–230V to 223V)
3. 50 Y DRIVE Assy ...........................................................(353V)
4. 50 SCAN A Assy ............................................................ (353V)
5. 50 SCAN B Assy ............................................................ (353V)
6. X CONNECTOR A Assy ................................(–230V to 223V)
7. X CONNECTOR B Assy ............................... (–230V to 223V)
Discharge the VSUS voltage, as shown below:
[Method for discharging the VSUS voltage]
1. Set DRF_SW on the DIGITAL VIDEO Assy to ON (Drive
OFF status). ∗1, ∗2
2. Leave the switch at that position for about 20-30 seconds.
3. If the power is on, turn it off. Then return DRF_SW to the OFF
position. ∗3
Notes
∗1: You can also set the unit to "Drive OFF status" by sending the
"DRF" RS232C command from the PC.
∗2: DRF_SW can be switched whether the power is on or off.
∗3: Power-down will occur if DRF_SW is set to OFF while the
power is on. (See "7.1.5 POWER ON/OFF FUNCTION FOR
THE LARGE-SIGNAL SYSTEM".) ... Refer to Service
Manual order NO. "PDP-504CMX: ARP3241"
: Part is the High Voltage Generating Points
other than the Charged Section.
: Part is Charged Section.
AC Inlet with Filter
Power Cord
Power Switch
(S1)
50 SCAN B Assy 50 Y DRIVE Assy
50 SCAN A Assy
POWER SUPPLY Unit 50 X DRIVE Assy X CONNECTOR B
Assy
X CONNECTOR A
Assy
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
5
A
B
C
D
5678
5678
PDP-505CMX
1. CANCELING DETECTION BY THE TRAP SWITCH
Outline: For video data transmission from the HDMI input to the plasma display, digital signals are used. Therefore, this unit adopts
the HDCP (High-bandwidth Digital Content Protection) system for copyright protection. This unit is also provided with a
detection switch (TRAP switch) that will prohibit the unit from being turned on again if the rear case of the unit is opened, in
order to prevent the panel technology from being leaked out.
Function: To deactivate the detection of the TRAP switch
Purposes: 1. During production of this unit, adjusting with the rear cover opened is possible.
2. During servicing or repairing, diagnoses of the assemblies are possible while the power is on.
Methods: For setting, use RS232C commands:
TSN: Ignore the monitoring of the switch
CTM: Clear the detection log of the switch
TSY: Reactivate monitoring of the switch
Notes:
•The TRAP switch is located on the chassis (see Fig.2 below).
•Once rear case opening is detected, send the TSN and CTM commands.
• Because the TSN command is not stored in memory, monitoring of the switch can be reactivated by turning the unit off then back on.
•The same setting is possible using the Factory menu.
• Canceling detection by the TRAP switch
¶How to enter Factory mode using the remote control unit
Please refer to the technical documentation (Service knowhow).
¶How to clear the detection log of the TRAP switch
In the INITIALIZE layer, hold the OSD key on the remote control unit pressed for at least 3 seconds.
¶After a power-down, to cancel detection of the TRAP switch using only the remote control unit, follow the
procedures below.
First, fix the TRAP switch to its depressed position. Set the drive ON/OFF switch in the DIGITAL VIDEO Assy to OFF,
Then enter the Factory mode. Press the MUTE key five times, then hold the DISPLAY key pressed for at least 4 seconds. Set the AC
switch on the panel to OFF. The log is also cleared. Then set the drive ON/OFF switch to ON.
Fig.2 TRAP switch
TRAP switch
(S2)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
6
A
B
C
D
1234
1234
PDP-505CMX
2. CONTRAST OF MISCELLANEOUS PARTS
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
Reference Nos. indicate the pages and Nos. in the service manual for the base model.
NOTES:
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
561
473
R50
1R0
5621
560
47k
0.5
1
RD1/4PU J
RD1/4PU J
RN2H K
RS1P K
56 x 10
1
47 x10
3
R50
1R0
561
473
5.62k RN1/4PC F562 x 10
1
5621
• Parts of the packing section are all mentioned in this manual.
2.1 PACKING SECTION
24
25
23
19
18
16
16
17
18
21
20
15
4
9
5
6
8
7
13
14
10
11
22
3
26
27
2
29
28
12
1
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
7
A
B
C
D
5678
5678
PDP-505CMX
• PACKING Parts List
Mark No. Description Part No.
1Operating Instructions ARD1059
(English/ French/ Japanese)
2Caution Sheet ARM1245
NSP 3 Warranty Card ARY1146
4Remote Control Unit AXD1486
5Battery Cover AZN2462
NSP 6 Dry Cell Battery VEM1031
7Binder Assy AEC1758
8Wiping Cloth (for screen) AED1285
9Vinyl Bag AHG1330
10 Display Stand AMR3264
11 Remote Control Holder AMR3268
12 Screws Set AXX1060
13 Washer WB80FTC
14 Bolt SMZ80H400FTC
15 Accessory Case Assy AHC1040
16 Pad AHA2280
17 Cord Case AHC1037
18 Under Carton AHD3037
19 Upper Carton (50D CMX) AHD3412
20 Mirror Mat AHG1284
21 Caution Sheet ARM1201
NSP 22 Accessory Assy (CMX2) AXX1069
>23 AC Power Cord ADG1215
NSP 24 Vinyl Bag AHG-195
25 Warranty Card ARY1166
26 Plasma Caution Sheet ARM1147
27 Caution Sheet ARM1200
28 Image Caution Sheet ARM1220
29 Image Stick Caution ARM1240
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
8
A
B
C
D
1234
1234
PDP-505CMX
PDP-505CMX/LUC5 and PDP-504CMX/LUC/1 are constructed the same except for the following :
PCB ASSEMBLIES
P15 - 3 1..DIGITAL VIDEO Assy AWV2169 AWV2248 Note.
NSP 1..RGB Assy AWV2185 Not used
P39 - 2 2..RGB Assy AWZ6992 Not used
NSP 1..RGB H Assy Not used AWV2247
P39 - 2 2..RGB H Assy Not used AWW1064 Note.
NSP 1..CMX FUKUGO Assy AWV2170 Not used
P39 - 4 2..AV I/O Assy AWZ6847 Not used
NSP 1..CMX FUKUGO H Assy Not used AWV2245
P39 - 4 2..AV I/O H Assy Not used AWW1062 Note.
CHASSIS SECTION (1)
P15 - 1 NSP P.Chassis (50) Assy AWU1111 Not used
P15 - 1 NSP P.Chassis (505) Assy Not used AWU1092
P15 - 4 FPC (114P) ADY1081 ADY1100
CHASSIS SECTION (2)
P17 - 11 F. Chassis VL ANA1753 ANA1886
P17 - 12 F. Chassis VR ANA1754 ANA1887
Power Switch (S2) (TRAP) Not used ASG1089 No1.
3P Housing Wire (J114) Not used ADX3049 No2.
FRAME SECTION
P19 - 6 Front Chassis H ANA1733 ANA1885
TERMINAL PANEL and REAR SECTION
P21 - 28 NSP Name Label AAL2516 AAL2703
FRONT SECTION
Gasket PH (50) Not used ANK1815 No3.
P23 - 5 Protect Panel Assy (50) AMR3348 Not used
P23 - 6 Panel Holder (50) ANG2563 Not used
Panel Holder H (50) Not used ANG2808 No4.
Panel Holder V (50) Not used ANG2809 No5.
P23 - 8 Front Case Assy AMB2788 AMB2878
CONTRAST TABLE
Part No.
PDP-504CMX
LUC/1
Ref. No. Symbol and Description Remarks
Mark PDP-505CMX
LUC5
: The numbers in the remarks column correspond to the numbers on the “ EXPLODED VIEWS ”.
Note : Although DIGITAL VIDEO Assy (AWV2248) and DIGITAL VIDEO Assy (AWV2169) are different in part number, they consist of the
same components.
: For PCB ASSEMBLIES, Refer to “ CONTRAST OF PCB ASSEMBLIES ”.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
9
A
B
C
D
5678
5678
PDP-505CMX
EXPLODED VIEWS
No.4
No.4 No.4
No.4 No.4
No.4
No.1
No.3
No.3
[Rear view]
[Rear view]
Screw
x 6
Screw
x 6
Screw
x 6
Screw
x 6
Screw
x 5
Screw
x 5
• Front section
• Chassis section
No.2
No.2
No.2
No.5
No.5
(ABZ30P060FTC)
(ABZ30P060FTC)
(ABZ30P060FTB)(ABZ30P060FTB)
(ABZ30P060FTB) (ABZ30P060FTB)
(Double Coated adhesive tape position)
(Double Coated adhesive tape position)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
10
A
B
C
D
1234
1234
PDP-505CMX
• AV I/O H ASSY (AWW1062)
[AV I/O H BLOCK]
SEMICONDUCTORS
IC7609 24LCS21A
IC7610, IC7613 AN5870SB
IC7602, IC7605-IC7607 BA4558F-HT
IC7603 BD3869AF
>IC7604 NJM78L09UA
IC7601 TC4052BFT
IC7612 TC74AC04FT
IC7611
TC74VHCT541AFTS1
Q7602, Q7605, Q7702 2SC4116
Q7603 DTA124EUA
Q7606-Q7608 DTC124EUA
Q7701 HN1C01FU
Q7601 RN1902
Q7609 SM6K2
D7601 1SS301
D7606-D7608, D7610, D7611 1SS302
D7613, D7614, D7616, D7617 1SS302
D7619, D7701 1SS355
D7602, D7603, D7605, D7609 UDZS5.6B
D7604
CAPACITORS
C7633, C7634 CCSRCH101J50
C7673, C7674 CCSRCH220J50
C7631, C7632 CCSRCH221J50
C7611, C7612 CCSRCH471J50
C7722 CEHAT100M50
C7654 CEHAT101M10
C7665 CEHAT101M16
C7623, C7648 CEHAT220M50
C7705 CEHAT221M6R3
C7714, C7716, C7718 CEHAT331M10
C7619, C7635, C7637, C7695, C7697 CEHAT470M16
C7721 CEHAT470M16
C7681, C7686, C7690 CEHAT471M16
C7601, C7602, C7609, C7610, C7614 CKSQYB225K10
C7616, C7638, C7639, C7643, C7653 CKSQYB225K10
C7627-C7630, C7640, C7650 CKSRYB102K50
C7642, C7652, C7660, C7661, C7666 CKSRYB103K50
C7676, C7680, C7685, C7689 CKSRYB103K50
C7698-C7703, C7707, C7712, C7713 CKSRYB103K50
C7715, C7717 CKSRYB103K50
C7621, C7622 CKSRYB104K16
C7603, C7620, C7662, C7663, C7667 CKSRYB105K10
C7675, C7677, C7678, C7684 CKSRYB105K10
C7693, C7694, C7723 CKSRYB105K10
C7641, C7651 CKSRYB222K50
C7646, C7656 CKSRYB471K50
C7617, C7618, C7624-C7626, C7636 CKSSYF104Z16
C7647, C7649, C7655, C7664, C7668 CKSSYF104Z16
C7679, C7682, C7683, C7687 CKSSYF104Z16
C7691, C7692, C7696, C7704, C7706 CKSSYF104Z16
C7708-C7711, C7720
RESISTORS
R7751-R7753 RS1/16S2200F
R7712, R7725 RS1/16S2201F
R7699-R7701, R7741-R7743 RS1/16S27R0F
R7653, R7654, R7673, R7674 RS1/16S3301F
R7709-R7711 RS1/16S75R0F
Other Resistors RS1/16S###J
OTHERS
CN7602, CN7603(JACK) AKN1069
CN7606, CN7607(15P D-SUB SOCKT) AKP1214
CN7601 (15P- PLUG ) KM200NA15
Mark No. Description Part No. Mark No. Description Part No.
CONTRAST OF PCB ASSEMBLIES
• RGB H ASSY
AWW1064 and AWZ6992 are constructed the same except for the following :
Mark Symbol and Description Part No.
AWZ6992 AWW1064 Remarks
[MAIN UCOM H BLOCK]
IC7208 TC74VHCT541AFT TC74VHCT541AFTS1
R7275, R7276 Not used RS1/16S472J *1
R7333 Not used RS1/16S101J *1
CN7204 Not used B3B-EH *1
[SUB LPF&AD H BLOCK]
F6601 ATF1194 ATF1213
[IC2 H BLOCK]
F7001, F7002 ATF1194 ATF1213
[IC3 H BLOCK]
F7101, F7102 ATF1194 ATF1213
*1 : Refer to “ 3. SCHEMATIC DIAGRAM ”.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
11
A
B
C
D
5678
5678
PDP-505CMX
[IF UCOM BLOCK]
SEMICONDUCTORS
IC8705 24LC01B
IC8702 HD64F3687FP
IC8703 PST9230N
IC8701 TC74VHC08FT
IC8704 TC7W126FU
Q8701 2SJ461A
Q8708 DTA124EUA
Q8702 DTC124EUA
COILS AND FILTERS
L8702 LCTAWR68J2520
CAPACITORS
C8706, C8707 CCSRCH120J50
C8708, C8714 CEHAT470M16
C8704, C8718 CEHAT471M6R3
C8717, C8720 CKSRYB103K50
C8722-C8724 CKSRYB471K50
C8709 CKSRYB472K50
C8701-C8703, C8705, C8711-C8713 CKSSYF104Z16
C8715, C8716, C8719, C8721, C8725 CKSSYF104Z16
RESISTORS
R8719, R8720, R8723, R8724, R8726 RAB4C101J
R8702, R8704, R8745 RAB4C103J
R8736 RS1/16S1302F
Other Resistors RS1/16S###J
OTHERS
CN8701 (PLUG 8-P) AKM1225
K8701-K8703 (TEST PIN) AKX9002
X8702 (CERAMIC RESONATOR) ASS1168
X8701 (32.768 KHz) ASS1172
CN8704 (6P PLUG) KM200NA6
[DVI HDCP BLOCK]
SEMICONDUCTORS
IC7502, IC7512 24LC02B(I)SN
IC7511 BD6522F
IC7503 SII1169CTU
IC7513
SN74AHC2G66HDCT
IC7504-IC7510 TC74LCX541FT
Q7503 DTA124EUA
Q7501, Q7504, Q7506, Q7507 RN1303
Q7502 RN1902
Q7505 SM6K2
D7501 1SS301
D7503-D7505 1SS302
D7502 UDZS6R8(B)
CAPACITORS
C7524, C7526, C7530, C7532 CCSRCH101J50
C7534, C7535, C7537, C7538 CCSRCH101J50
C7541, C7542, C7546, C7548-C7550 CCSRCH101J50
Mark No. Description Part No.
C7504, C7507 CCSRCH221J50
C7528, C7578, C7579 CEHAT101M10
C7522 CEHAT221M6R3
C7502, C7510, C7516, C7518 CEHAT470M16
C7503, C7506 CKSRYB222K50
C7514, C7520, C7573-C7577 CKSRYB471K50
C7501, C7509, C7513, C7515, C7517 CKSSYF104Z16
C7519, C7521, C7523, C7525, C7527 CKSSYF104Z16
C7529, C7531, C7533, C7536 CKSSYF104Z16
C7539, C7540, C7543-C7545, C7547 CKSSYF104Z16
C7551-C7559, C7580, C7581, C8582 CKSSYF104Z16
RESISTORS
R7560-R7565, R7568-R7573 RAB4CQ0R0J
R7524-R7529, R7536, R7540 RAB4CQ100J
R7552-R7555 RAB4CQ100J
R7578-R7590 RAB4CQ470J
R7538 RS1/16S3900F
Other Resistors RS1/16S###J
OTHERS
CN7501 (JACK) AKN1069
CN7503 (DVI SOCKET 24P) AKP1250
Mark No. Description Part No.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
12
A
B
C
D
1234
1234
PDP-505CMX
3. SCHEMATIC DIAGRAM
3.1 OVERALL WIRING DIAGRAM
AWZ6851
Refer to the "Service Manual (ARP3192)."
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
13
A
B
C
D
5678
5678
PDP-505CMX
Refer to the "Service Manual (ARP3192)."
÷When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷The >mark found on some component parts indicates the importance of the safety factor of
the part. Therefore, when replacing, be sure to use parts of identical designation.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
14
A
B
C
D
1234
1234
PDP-505CMX
3.2 RGB ASSY (9/10)
1/2
2/2
2/2
Large size
SCH diagram
RGB ASSY
• MAIN UCOM H BLOCK
STB
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
Other manuals for PDP505CMX - HD Plasma Display
3
Table of contents
Other Pioneer Monitor manuals
Pioneer
Pioneer AVX-7600 User manual
Pioneer
Pioneer PDP6100HD - 61" Plasma Panel User manual
Pioneer
Pioneer PDP-505PE User manual
Pioneer
Pioneer PDP-5000EX User manual
Pioneer
Pioneer PDP-505MX User manual
Pioneer
Pioneer PDP5050SX User manual
Pioneer
Pioneer PDP-50MXE20 User guide
Pioneer
Pioneer Pure Vision PDP-425CMX User manual
Pioneer
Pioneer PDP-50MXE1 User manual
Pioneer
Pioneer PDP 607CMX User manual
Pioneer
Pioneer PDP 507CMX User manual
Pioneer
Pioneer PDP-6071PU User manual
Pioneer
Pioneer PDP-V402E User manual
Pioneer
Pioneer PureVision PDP-427CMX User manual
Pioneer
Pioneer PDP-4214HD User manual
Pioneer
Pioneer Pure Vision PDP-425CMX Manual
Pioneer
Pioneer PLASMA DISPLAY User manual
Pioneer
Pioneer PDP5030HD - PDP - 503OHD Setup guide
Pioneer
Pioneer PDU-50WX2 User manual
Pioneer
Pioneer PDP-4330HD User manual
