Pioneer Elite SC-91 User manual

Operating Instructions
AV Receiver SC-91

2
WARNING
This equipment is not waterproof
. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear
, and 20 cm at each
side).
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1b_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).
D3-4-2-1-7c*_A2_En
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating.
To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
Caution
To prevent fire hazard, the Class 2 Wiring Cable
should be used for connection with speaker, and
should be routed away from hazards to avoid damage
to the insulation of the cable.
D3-7-13-67*_A1_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
WARNING: This product contains chemicals known
to the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
D36-P5_C1_En

3
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED
WARRANTY CARD AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
D36-AP9-1_A1_En
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_E
n
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately
.
D41-6-4_A1_En
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
D8-9-2-5_A1_En
5.15-5.25 GHz band is restricted to indoor operations
only.
D8-9-2-6_A1_En
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
D8-9-10-1_A1_En
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF)
Exposure Guidelines. This equipment should be
installed and operated keeping the radiator at least
20 cm or more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
D8-9-2-7-2_A2_En
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment and
meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment should be installed
and operated keeping the radiator at least 20 cm or
more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
D8-9-2-7-4_A1_En

4
Thank you for buying this Pioneer product. Please read through these operating instruc-
tions so you will know how to operate your model properly.
Contents
01 Before you start
Features............................................................................................................................................................................... 8
Checking what’s in the box..............................................................................................................................................10
Installing the receiver.......................................................................................................................................................11
Loading the batteries........................................................................................................................................................11
Operating range of remote control unit..........................................................................................................................11
02 Controls and displays
Remote control ................................................................................................................................................................. 13
Display ...............................................................................................................................................................................15
Front panel ........................................................................................................................................................................16
03 Connecting your equipment
Connecting your equipment............................................................................................................................................19
Rear panel .........................................................................................................................................................................19
Determining the speakers’ application ..........................................................................................................................20
Placing the speakers........................................................................................................................................................22
Connecting the speakers.................................................................................................................................................23
Installing your speaker system........................................................................................................................................24
About the audio connection ............................................................................................................................................26
About the video converter................................................................................................................................................27
About HDMI ......................................................................................................................................................................27
Connecting your TV and playback components............................................................................................................28
Connecting an HDD/DVD recorder, BD recorder and other video sources ...............................................................30
Connecting a satellite/cable receiver or other set-top box ...........................................................................................31
Connecting other audio components.............................................................................................................................32
Connecting the subwoofer ..............................................................................................................................................32
Connecting AM/FM antennas.........................................................................................................................................32
Making MULTI-ZONE connections .................................................................................................................................33
Connecting to the network through LAN interface .......................................................................................................35
Connecting an iPod..........................................................................................................................................................36
Connecting a USB device................................................................................................................................................36
Connecting an MHL-compatible device.........................................................................................................................36
Connecting an HDMI-equipped component to the front panel input .........................................................................37
Connecting an IR receiver ...............................................................................................................................................37
Switching components on and off using the 12 volt trigger.........................................................................................37
Plugging in the receiver ...................................................................................................................................................37
04 Basic Setup
Initial settings of this receiver..........................................................................................................................................39
Setting with a special application (Start-up Navi) .........................................................................................................39
Perform settings using the AVNavigator built into this receiver..................................................................................39
Setting by referring to the operating instructions .........................................................................................................41
Setting network connection ............................................................................................................................................41
05 Basic playback
Playing a source ...............................................................................................................................................................51
Playing an iPod .................................................................................................................................................................52
Playing a USB device .......................................................................................................................................................53
Playing an MHL-compatible device ................................................................................................................................54
Listening to the radio........................................................................................................................................................55
Music playback using Bluetooth wireless technology ..................................................................................................56
06 Listening to your system
Enjoying various types of playback using the listening modes....................................................................................59
Selecting MCACC presets ...............................................................................................................................................60
Choosing the input signal................................................................................................................................................ 60
Better sound using Phase Control..................................................................................................................................61
Better sound using Phase Control and Full Band Phase Control ...............................................................................61
07 Playback with NETWORK features
Introduction.......................................................................................................................................................................63
Playback with Network functions....................................................................................................................................64
About network playback...................................................................................................................................................66
About playable file formats..............................................................................................................................................68
08 Control with HDMI function
About the Control with HDMI function...........................................................................................................................70
Making Control with HDMI connections........................................................................................................................70
HDMI Setup.......................................................................................................................................................................70
Before using synchronization..........................................................................................................................................71
About synchronized operations ......................................................................................................................................71
Sound Retriever Link ........................................................................................................................................................71
Cautions on the Control with HDMI function ................................................................................................................71
09 Using other functions
Setting the Audio options ................................................................................................................................................73
Setting the Video options.................................................................................................................................................75
Switching the output (OUTPUT PARAMETER)..............................................................................................................75
HDMI 4K/60p signal input setting...................................................................................................................................76
Changing the channel level while listening ...................................................................................................................76
Using the MULTI-ZONE controls.....................................................................................................................................77
Making an audio or a video recording ............................................................................................................................78
Network settings from a web browser............................................................................................................................78
Using the sleep timer .......................................................................................................................................................78
Dimming the display ........................................................................................................................................................78
Checking your system settings .......................................................................................................................................78
Resetting the system........................................................................................................................................................79

5
10 Controlling the rest of your system
About the Remote Setup menu.......................................................................................................................................81
Operating multiple receivers ...........................................................................................................................................81
Setting the remote to control other components..........................................................................................................81
Selecting preset codes directly .......................................................................................................................................81
Programming signals from other remote controls .......................................................................................................82
Erasing one of the remote control button settings........................................................................................................82
Erasing all learnt settings that are in one input function .............................................................................................82
Using All Zone Standby....................................................................................................................................................83
Setting the switching time for the receiver operation mode ........................................................................................83
Resetting the remote control settings............................................................................................................................83
Controlling components ..................................................................................................................................................84
11 The MCACC PRO menu
Making receiver settings from the MCACC PRO menu................................................................................................87
Automatic MCACC (Expert).............................................................................................................................................87
Manual MCACC setup .....................................................................................................................................................88
Checking MCACC Data....................................................................................................................................................91
Data Management............................................................................................................................................................92
12 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu...............................................................................................94
Manual speaker setup......................................................................................................................................................94
MHL Setup ........................................................................................................................................................................96
The Other Setup menu.....................................................................................................................................................96
Making network settings using Safari............................................................................................................................98
Using Safari to set a friendly name.................................................................................................................................99
Using Safari to update the firmware...............................................................................................................................99
13 FAQ
Troubleshooting..............................................................................................................................................................101
Power...............................................................................................................................................................................101
No sound .........................................................................................................................................................................101
Other audio problems ....................................................................................................................................................102
BT AUDIO ........................................................................................................................................................................103
Video ................................................................................................................................................................................103
Settings............................................................................................................................................................................103
Professional Calibration EQ graphical output.............................................................................................................104
Display .............................................................................................................................................................................104
Remote control ...............................................................................................................................................................104
HDMI................................................................................................................................................................................104
MHL..................................................................................................................................................................................105
Built-in AVNavigator.......................................................................................................................................................105
USB interface..................................................................................................................................................................106
iPod ..................................................................................................................................................................................106
Network ...........................................................................................................................................................................106
Wireless LAN...................................................................................................................................................................108
14 Additional information
About Wi-Fi®....................................................................................................................................................................110
SABRE DACTM.................................................................................................................................................................110
About HDMI ....................................................................................................................................................................110
HTC Connect...................................................................................................................................................................110
About iPod.......................................................................................................................................................................110
Windows 8.......................................................................................................................................................................111
MHL..................................................................................................................................................................................111
About Bluetooth wireless technology ...........................................................................................................................111
Software license notice..................................................................................................................................................111
Surround sound formats ...............................................................................................................................................113
Auto Surround, ALC and Stream Direct with different input signal formats............................................................113
Speaker Setting Guide....................................................................................................................................................114
About messages displayed when using network functions.......................................................................................115
Important information regarding the HDMI connection ............................................................................................115
Cleaning the unit ............................................................................................................................................................115
Glossary ...........................................................................................................................................................................116
Features index.................................................................................................................................................................118
Specifications .................................................................................................................................................................119
Preset code list................................................................................................................................................................121

6
Flow of settings on the receiver
Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used eas-
ily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 8, 10
Setting to be made as necessary: 6, 7, 9, 11, 12, 13, 14
Important
Using Wiring Navi on AVNavigator of this receiver, you can make the initial settings of the receiver on your com-
puter or mobile device. In that case, you can use Wiring Navi to make the same connections or settings that are
performed in Steps 2, 3, 4, 5, 6, 8, and 9. For details of how to use AVNavigator, refer to How to use the built-in
AVNavigator on page 39.
1 Before you start
!Checking what’s in the box on page 10
!Loading the batteries on page 11
j
2 Determining the speakers’ application (page 20)
![A] 7.2 channel surround system (Surround back/Top middle) connection
![B] Dolby Enabled Speaker system connection
![C] 7.2 channel surround system (Surround back/Front wide) connection
![D] 7.2 channel surround system & Speaker B connection
![E] 5.2 channel surround system & Front Bi-amping connection (High quality surround)
![F] 5.2 channel surround system & ZONE 2 connection (Multi Zone)
![G] 5.2 channel surround system & HDZONE connection (Multi Zone)
j
3 Connecting the speakers
!Placing the speakers on page 22
!Connecting the speakers on page 23
!Installing your speaker system on page 24
!Bi-amping your speakers on page 26
j
4 Connecting the components
!About the audio connection on page 26
!About the video converter on page 27
!Connecting your TV and playback components on page 28
!Connecting AM/FM antennas on page 32
!Plugging in the receiver on page 37
j
5 Power On
j
6 Changing the OSD display language (OSD Language) (page 49)
j
7 Using the AVNavigator functions (page 39)
j
8 MCACC speaker settings
!Automatically conducting optimum sound tuning (Full Auto MCACC) on page 47
j
9 The Input Setup menu (page 48)
(When using connections other than the recommended connections)
j
10 Basic playback (page 50)
j
11 Switching the HDMI output (page 76)
j
12 Adjusting the sound and picture quality as desired
!Using the various listening modes (page 58)
!Better sound using Phase Control (page 61)
!Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 87)
!Changing the channel level while listening (page 95)
!Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 73)
!Setting the Audio options (page 73)
!Setting the Video options (page 75)
j
13 Other optional adjustments and settings
!Control with HDMI function (page 69)
!The MCACC PRO menu (page 86)
!The System Setup and Other Setup menus (page 93)
j
14 Making maximum use of the remote control
!Operating multiple receivers (page 81)
!Setting the remote to control other components (page 81)

7
Features............................................................................................................................................8
Checking what’s in the box ..........................................................................................................10
Installing the receiver....................................................................................................................11
Loading the batteries ....................................................................................................................11
Operating range of remote control unit...................................................................................... 11
Before you start

8
Before you start
01
Features
Audio
%Dolby Atmos
This AV receiver supports the latest Dolby Atmos surround sound system. Dolby Atmos is a new technology in
which, through real time calculation of audio data and meta data (position and time information) included in the
audio signal, a surround sound space is achieved irrespective of the speaker layout and number of speakers.
Dolby Atmos contents are required to enjoy Dolby Atmos. For Blu-ray discs with Dolby Atmos, Dolby Atmos can
be played by connecting most conventional Blu-ray discs with this receiver using HDMI.
%Class D Amplifier
This unit is an AV receiver developed based on the latest high performance Class D amplifier and integrating
the essence of Pioneer’s high sound quality designs. This new generation reference amplifier offers outstanding
performance with high sound quality and reproduces the latest in multi-channel digital contents.
%ESS-24bit-DAC-equipped
All channels are equipped with ESS SABRE Premier Audio DACs. The Jitter Eliminators achieve clearer sound.
%Hi-bit 24 Audio Processing
Creates a wider dynamic range with digital sources like CDs or DVDs. 16- and 20-bit PCM as well as compressed
audio is requantized to 24 bits, and the high frequency component is interpolated upon data processing to enable
smoother, more subtle musical expression.
%Easy setup using MCACC PRO
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced fea-
tures of Professional Acoustic Calibration EQ.
%Auto Phase Control Plus
For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first
place. This function automatically corrects phase shifting on such discs and broadcasts. This function is particu-
larly effective when playing multi-channel music containing low frequency effects (LFE).
%Full Band Phase Control
The further advanced Full Band Phase Control technology focuses on the group delay in the speaker network
filter, and compensates with special digital signal processing (DSP), to adjust the phase of each unit as well as
the group delay for each speaker. Full Band Phase Control gives multi-range speakers the sound coherence of
full-range speakers, while retaining the wide frequency range advantage.
%Subwoofer EQ
The EQ for subwoofer output can be corrected. In addition to the results of MCACC automatic adjustment, the
subwoofer output can be adjusted to match the viewing environment or your taste by manual correction.
%Virtual Speakers
By turning on the ‘Virtual Surround Back’, ‘Virtual Height’, and ‘Virtual Wide’ modes, it is possible to realize a
maximum of 11.1 channels combining the speakers that are actually installed and the virtual speakers. This
makes for a smoother connection between the sounds and an improved 3D feel.
Video
%Ultra HD (with 4K/60p video support) - Pass-through and upscaling -
Up to 4K/60p resolution images can be passed through and displayed as such, and the HD (High Definition) or
Full HD images of DVDs, Blu-ray discs and HD broadcasts can be upscaled to a resolution of up to 4K/60p and
displayed. A separate monitor supporting Ultra HD (4K video) is required.
%HDMI (4K/60p, 3D, Audio Return Channel)
A compatible component is required to use the above function.
%HDCP 2.2
This receiver is compatible with the HDCP 2.2 standard, which has stringent copyright protection technology.

9
Before you start
01
Network
%Built-in Wi-Fi
This receiver is compatible with Wi-Fi standards, and supports the 2.4 GHz and 5 GHz dual bands.
%Wireless Direct
With this receiver, you can enjoy music playback without a router by direct wireless connection using an iPhone
or other Wi-Fi mobile device.
%Spotify Connect
Spotify is a digital music-streaming service that gives you access to millions of songs instantly. This receiver is
ready for Spotify Connect, which lets you play music on your audio system, using the Spotify app as a remote. For
service availability in your country check www.spotify.com.
%Compatible with Windows 8.1
This receiver is compatible with Windows 8.1, letting you easily stream music from compatible PCs on your home
network.
%Apple AirPlay
With AirPlay you can stream music from iTunes to this receiver and play it through your home theater system.
You can even use the receiver to view metadata including song titles, artist’s names as well as the album art on a
connected display. You can easily enjoy your iTunes music in any room in the house.
%DLNA Certified (1.5)
This receiver is a DLNA certified (1.5) device, enabled to work not only as a DMP (Digital Media Player) for playing
DMS (Digital Media Server) audio files, but also as a DMR (Digital Media Renderer) to be controlled remotely by a
device such as a smartphone or PC.
%Internet Radio
When you connect this receiver to the network, you can listen to internet radio from around the world. You can
register your favorite broadcasting stations in this receiver.
%Multi-channel Music File playback
This receiver enables multi-channel music file playback with a resolution of up to 96 kHz/24 bit. Playback of WAV
and FLAC files via the front USB port and network is supported.
%DSD File Music playback (via Network, Front USB and HDMI)
Playback of high sound quality DSD music (DSD files and DSD discs (SACDs)) is supported.
%High Resolution Music Playback
High resolution music files with resolutions of 96 kHz/24 bit to 192 kHz/24 bit can be played. Playback of AIFF,
Apple Lossless, WAV and FLAC files via the front USB port and network is supported.
%Gapless Playback
The silent section between tracks is skipped when playing music files, eliminating the interruptions that usually
occur when playing live or concert contents.
This receiver plays back AAC or MP3 format files with a minimum gap even though it is fundamentally impossible
to play back without a gap.
Connectivity
%Built-in Bluetooth Wireless Technology
This receiver, equipped with Bluetooth wireless technology, lets you enjoy music files on an iPhone or other
Bluetooth wireless technology enabled device wirelessly.
%MHLTM (Mobile High-definition Link)-compatible device playback
An incorporates MHL 2 mobile device can be connected to enjoy 3D videos, full-HD videos, high quality multi-
channel audio, and photos etc., with charge the battery on the receiver.
%HTC Connect
HTC Connect makes it easy to wirelessly stream your favorite music straight from your HTC phone. There’s no
need for a separate app; HTC Connect is built right in your phone’s music player.
%iPod Playback
Your iPod and iPhone can be connected to the receiver’s USB terminal to play the music files on the iPod or
iPhone. Also, the iPod or iPhone is charged when it is connected to the receiver.

10
Before you start
01
Installation
%Built-in AVNavigator
With the built-in AVNavigator embedded in this receiver, Wiring Navi can be used to interactively connect and
set initial settings of this receiver with a smart phone, tablet, PC, and Mac through a home network. In addition,
Interactive Operation Guide can also be used, which visually explains the functions and operation by actually
experiencing the operation with contents linked with the main device.
%iControlAV5 Remote Application
This is an application that allows intuitive operation of many of the receiver’s functions. This application is avail-
able on the App Store for iPhone, iPod touch and iPad. You can also get it on Google Play for Android smart-
phones. The application can be downloaded free of charge.
%HDZONE output
This receiver supports output of the HDMI output to a subzone room. Powerful images can be enjoyed simply by
connecting this receiver to a TV supporting 4K/Full-HD/3D. In addition, a multi-channel environment can be cre-
ated by connecting this receiver to another AV receiver in the subzone room.
%ZONE Ready
This receiver is equipped with HDZONE and ZONE 2. HDZONE supports HD audio/video streaming to a separate
room via HDMI. Multi-Zone enables music and movie playback from different sources in three zones at the same
time.
%Energy Saving Design
This AV receiver has an ecological design. In addition to even lower power consumption in standby, the receiver
is equipped with an ‘eco mode’ for low power consumption when playing contents as well. Furthermore, the eco
mode can easily be set with a dedicated button on the remote control of using iControlAV5.
Checking what’s in the box
Please check that you’ve received the following supplied accessories:
!Setup microphone (cable: 5 m (16.4 ft.))
!Remote control unit
!AAA size IEC R03 dry cell batteries (to confirm system operation) x2
!AM loop antenna
!FM wire antenna
!Power cord
!CD-ROM
!Quick start guide
!Safety Brochure
!Warranty sheet
Note
The illustrations are modified and simplified for explanation purposes and may be different from the actual
product.
Handling the CD-ROM
Precautions For Use
!This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.
License
!Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
!Copyright to data provided on this CD-ROM belongs to PIONEER HOME ELECTRONICS CORPORATION.
Unauthorized transfer, duplication, broadcast, public transmission, translation, sales, lending or other such
matters that go beyond the scope of “personal use” or “citation” as defined by Copyright Law may be subject to
punitive actions. Permission to use this CD-ROM is granted under license by PIONEER HOME ELECTRONICS
CORPORATION.
General Disclaimer
!PIONEER HOME ELECTRONICS CORPORATION does not guarantee the operation of this CD-ROM with
respect to personal computers using any of the applicable OS. In addition, PIONEER HOME ELECTRONICS
CORPORATION is not liable for any damages incurred as a result of use of this CD-ROM and is not responsible
for any compensation. The names of private corporations, products and other entities described herein are the
registered trademarks or trademarks of their respective firms.

11
Before you start
01
Installing the receiver
!When installing this unit, make sure to put it on a level and stable surface.
!Don’t install it on the following places:
—on a color TV (the screen may distort)
—near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
—in direct sunlight
—in damp or wet areas
—in extremely hot or cold areas
—in places where there is vibration or other movement
—in places that are very dusty
—in places that have hot fumes or oils (such as a kitchen)
!Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.
Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We rec-
ommend using alkaline batteries that have a longer life.
!The remote control setting may be restored to the default after the batteries are replaced. If this happens, reset
it (page 83).
WARNING
!Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or perfor-
mance of batteries.
CAUTION
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
!Never use new and old batteries together.
!Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
!When inserting the batteries, make sure not to damage the springs on the battery’s (–) terminals. This can
cause batteries to leak or overheat.
!Batteries with the same shape may have different voltages. Do not use different batteries together.
!When disposing of used batteries, please comply with governmental regulations or environmental public insti-
tution’s rules that apply in your country/area.
Operating range of remote control unit
The remote control may not work properly if:
!There are obstacles between the remote control and the receiver’s remote sensor.
!Direct sunlight or fluorescent light is shining onto the remote sensor.
!The receiver is located near a device that is emitting infrared rays.
!The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m (23 ft.)

12
Remote control ..............................................................................................................................13
Display............................................................................................................................................15
Front panel.....................................................................................................................................16
Controls and displays

13
Controls and displays
02
Remote control
This section explains how to operate the remote control for the receiver.
RECEIVER
D.ACCESS
DIMMER SLEEP
RCU SETUP
MPX
PRESET TUNE
BAND PTY
iPod
TUNER
INPUT
USB ADPTROKU
BT
TV
TV
MHL
CD
OUT P.
DVDBD
ALL ZONE STBY
SOURCE
STANDBY/ON
MAIN
SAT
SUB ZONE CONTROL
SOURCE CONTROL
MUTE
VOLUME
VOL
TOP
MENU
HOME
MENU
TOOLS
MENU
ENTER
RETURN
CLASS
ENTER CLR
CH
CH
2
546
8
0
79
13
AUDIO
DISP
SURRAUTO
CH LV.
ADV
STATUS
AUDIO P. VIDEO P.
Z2 Z3 HDZ
LISTENING MODE
HDMI
NET
ALL
Fav
RECEIVER
1
2
4
3
9
10
11
12
5
6
7
8
13
14
17
18
15
16
6
The remote has been conveniently color-coded according to component control using the following system:
!White – Receiver control, TV control
!Blue – Operation of other devices and each input (TUNER, etc.) (See pages 52, 53, 55, 56 and 84.)
1 uSTANDBY/ON
This switches between standby and on for this receiver.
2 ALL ZONE STBY
Use this button to perform unique operations (page 83).
3 MAIN RECEIVER
Switches the remote to control the receiver (used to select the white commands).
Switch to perform operations in the main zone.
4 SOURCE CONTROL buttons
Switches the input. Also, switches remote control operation mode for operating other devices or each input
(TUNER, etc.) (page 81).
The input for HDMI , NET and ALL switches each time these buttons are pressed.
5 TV control buttons
These buttons can be used to perform operations on the TV to which the TV INPUT button is assigned. The TV can
be operated with these buttons regardless of the input set for the remote control’s operation mode (page 81).
6 Receiver Control buttons
!STATUS – Displays the IP address and information such as selected/set functions and input signals on the
display (page 78).
!OUT P. (OUTPUT PARAMETER) – Switches the output terminal of the HDMI signal or speaker terminal to be
played (page 75).
!RETURN – Press to confirm and exit the current menu screen.
!CH LV. (CHANNEL LEVEL) – Press repeatedly to select a channel, then use k/lto adjust the level (pages
76 and 95).
7 Receiver setting buttons
Press MAIN RECEIVER first to access:
!AUDIO P. (AUDIO PARAMETER) – Use to access the Audio options (page 73).
!VIDEO P. (VIDEO PARAMETER) – Use to access the Video options (page 75).
!HOME MENU – Use to access the Home Menu (pages 48, 49, 70, 87 and 94).
8 i/j/k/l/ENTER
Use the arrow buttons when setting up your surround sound system (see page 87) and the Audio or Video
options (page 73 or 75).
9 LISTENING MODE buttons
!AUTO (AUTO SURROUND/ALC/STREAM DIRECT) – Switches between Auto Surround (page 59), Auto
Level Control mode and Stream Direct mode (page 60).
!SURR (STANDARD SURROUND) – Press for Standard decoding and to switch various modes (Dolby, DTS,
etc.) (page 59).
!ADV (ADVANCED SURROUND) – Use to switch between the various surround modes (page 59).
10 Source device operation button
Operates other devices or each input (TUNER, etc.).
11 DIMMER
Dims or brightens the display (page 78).
12 SLEEP
Use to put the receiver in sleep mode and select the amount of time before sleep (page 78).

14
Controls and displays
02
13 uSOURCE
Press to turn on/off the power to the Pioneer device connected to the receiver.
14 Remote control LED
Lights when a command is sent from the remote control.
15 SUB ZONE CONTROL buttons
!Z2 (ZONE 2) – Holding down this button (for 1.5 seconds) until the remote control LED flashes one time, the
mode changes to Zone 2 operation.
!Z3 (ZONE 3) – It is not used with this receiver.
!HDZ (HDZONE) – Holding down this button (for 1.5 seconds) until the remote control LED flashes one time,
the mode changes to HDZONE operation.
16 VOLUME +/–
Use to set the listening volume.
To adjust the main zone sound volume, press MAIN RECEIVER first and then press this button. When in the sub
zone, press the SUB ZONE CONTROL button first and then press this button.
17 MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
To mute the main zone sound volume, press MAIN RECEIVER first and then press this button. When in the sub
zone, press the SUB ZONE CONTROL button first and then press this button.
18 RCU SETUP
Used to set the remote control (page 81).

15
Controls and displays
02
Display
HDMI
DIGITAL
ANALOG
L C R
SL SR
XL XR
XC
LFE
AUTO
DIGITAL PLUS
AUTO SURROUND
STREAM DIRECT
Neo:6
ADV.SURROUND
STANDARD
SP AB SLEEP
DSD PCM
DTS HD ES 96/24
MSTR
S.RTRV SOUND UP MIX
MONO
dB
MULTI-ZONE STEREO TrueHD
TUNED
ALC AT T
USB
TV
DVD
HDMI
DVR BD
CD TUNER
iPod
[ 2 ][ 3 ][ 4 ]
21 3 974 10811 12 13
19 2015 16 17 18
146
FULL BAND
5
6
1 Signal indicators
Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input sig-
nal automatically (page 60).
2 Program format indicators
Light to indicate the channels to which digital signals are being input.
With Dolby Atmos content, the light will not be on when the object base signal is being decoded.
!L/R – Left front/Right front channel
!C– Center channel
!SL/SR – Left surround/Right surround channel
!LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input)
!XL/XR – Two channels other than the ones above
!XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag
3 Digital format indicators
Light when a signal encoded in the corresponding format is detected.
!DIGITAL – Lights with Dolby Digital decoding.
!DIGITAL PLUS – Lights with Dolby Digital Plus decoding.
!TrueHD – Lights with Dolby TrueHD decoding.
!DTS – Lights with DTS decoding.
!DTS HD – Lights with DTS-HD decoding.
!96/24 – Lights with DTS 96/24 decoding.
!DSD – Lights during playback of DSD (Direct Stream Digital) signals.
!DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion.
!PCM – Lights during playback of PCM signals.
!MSTR – Lights during playback of DTS-HD Master Audio signals.
4 MULTI-ZONE
Lights when the MULTI-ZONE feature is active (page 77).
5 FULL BAND
Lights when the Full Band Phase Control is switched on (page 61).
6 Listening mode indicators
!ALC – Lights when the ALC (Auto level control) mode is selected (page 59).
!AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 59).
!STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 60).
!ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 59).
!STANDARD – Lights when one of the Standard Surround modes is switched on (page 59).
7 (PHASE CONTROL)
Lights when the Phase Control is switched on (page 61).
8 ATT
Lights when the input signal level is lowered to reduce distortion (page 73).
9 SOUND
Lights when the DIALOG E (Dialog Enhancement) or TONE (tone controls) features is selected (page 73).
10 Tuner indicators
!TUNED – Lights when a broadcast is being received.
!STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode.
!MONO – Lights when the mono mode is set using MPX.
11
Lights when the sound is muted.
12 Master volume level
Shows the overall volume level.
“---” indicates the minimum level, and “+12dB” indicates the maximum level.
13 Input function indicators
Light to indicate the input function you have selected.
14 Scroll indicators
Light when there are more selectable items when making the various settings.
15 Speaker indicators
Lights to indicate the current speaker system using OUT P. (page 75).
16 SLEEP
Lights when the receiver is in sleep mode (page 78).
17 Matrix decoding format indicators
!Neo:6 – When one of the Neo:6 modes of the receiver is on, this lights to indicate Neo:6 processing (page
59).
18 S.RTRV
Lights when the Auto Sound Retriever function is active (page 73).
19 Character display
Displays various system information.
20 Remote control mode indicator
Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 98)

16
Controls and displays
02
Front panel
PHONES
SPEAKERS
MULTI-ZONE
CONTROL
ZONE 2
ON/OFF
MCACC
SETUP MIC
ENTER
TUNE
TUNE
PRESETPRESET
VIDEO
PARAMETER
AUDIO
PARAMETER
HDMI 5 INPUT
AUTO/ALC/
DIRECT STATUSBANDTUNER EDIT
iPod iPhone
DIRECT CONTROL
HOME MENURETURN
MASTER
VOLUME
STANDBY/ON
INPUT
SELECTOR
5V 1 A
HDZONE
ON/OFF
PHASE
CONTROL
1 2 4
35
6
7
8910 1211 13 16
17 18 2019 21 22
3
14 15
23
1 uSTANDBY/ON
This switches between standby and on for this receiver.
2 INPUT SELECTOR dial
Use to select an input function.
3 Indicators
!MCACC PRO – Lights when EQ is set to ON in the AUDIO PARAMETER menu (page 73).
!FL OFF – Lights when “off” (nothing displayed) is selected with the display’s dimmer adjustment (page 78).
!HDMI – Blinks when connecting an HDMI-equipped component; lights when the component is connected
(page 28).
!WIRELESS – Lights when connected to the network with wireless. The light slowly blinks during WAC
(Wireless Accessary Configuration) mode (page 43).
4 Character display
See Display on page 15.
5 Remote sensor
Receives the signals from the remote control (page 11).
6 MASTER VOLUME dial
7 Front panel controls
To access the front panel controls, catch the sides of the door with your fingers and pull forward.
MASTER
VOLUME
STANDBY/ON
INPUT
SELECTOR
8 AUDIO PARAMETER
Use to access the Audio options (page 73).
9 i/j/k/l(TUNE/PRESET) /ENTER
Use the arrow buttons when setting up your HOME MENU. Use TUNE i/jto find radio frequencies and use
PRESET k/lto find preset stations (page 55).
10 VIDEO PARAMETER
Use to access the Video options (page 75).
11 MULTI-ZONE controls
If you’ve made MULTI-ZONE connections (page 33) use these controls to control the sub zone from the main
zone (page 77).
12 SPEAKERS
Use to change the speaker terminal (page 75).
13 iPod iPhone DIRECT CONTROL
Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 52).
14 AUTO SURR/ALC/STREAM DIRECT
Switches between Auto Surround (page 59), Auto Level Control and Stream Direct mode (page 60).
15 STATUS
Displays the IP address and information such as selected/set functions and the input signal on the display (page
78).
16 TUNER controls
!BAND – Switches between AM and FM radio bands (page 55).
!TUNER EDIT – Use with TUNE i/j, PRESET k/land ENTER to memorize and name stations for recall
(page 55).
17 HOME MENU
Use to access the Home Menu (pages 49, 48, 70, 87 and 94).
18 RETURN
Press to confirm and exit the current menu screen.
19 PHASE CONTROL
Press to switch on/off Phase Control (page 61).
20 PHONES jack
Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.

17
Controls and displays
02
21 MCACC SETUP MIC jack
Use to connect the supplied microphone (page 47).
22 iPod/iPhone terminals
Use to connect your Apple iPod/iPhone as an audio source (page 36), or connect a USB device for audio and
photo playback (page 36).
23 HDMI 5 INPUT terminal
Use for connection to a compatible HDMI device (Video camera, etc.) (page 37).

18
Connecting your equipment.........................................................................................................19
Rear panel ......................................................................................................................................19
Determining the speakers’ application........................................................................................ 20
Placing the speakers......................................................................................................................22
Connecting the speakers............................................................................................................... 23
Installing your speaker system..................................................................................................... 24
About the audio connection......................................................................................................... 26
About the video converter ...........................................................................................................27
About HDMI ...................................................................................................................................27
Connecting your TV and playback components .........................................................................28
Connecting an HDD/DVD recorder, BD recorder and other video sources............................... 30
Connecting a satellite/cable receiver or other set-top box........................................................ 31
Connecting other audio components ..........................................................................................32
Connecting the subwoofer...........................................................................................................32
Connecting AM/FM antennas....................................................................................................... 32
Making MULTI-ZONE connections................................................................................................33
Connecting to the network through LAN interface ................................................................... 35
Connecting an iPod........................................................................................................................36
Connecting a USB device .............................................................................................................. 36
Connecting an MHL-compatible device.......................................................................................36
Connecting an HDMI-equipped component to the front panel input ...................................... 37
Connecting an IR receiver .............................................................................................................37
Switching components on and off using the 12 volt trigger..................................................... 37
Plugging in the receiver ................................................................................................................ 37
Connecting your equipment

19
Connecting your equipment
03
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter
explains the kinds of components you can connect to make up your home theater system.
CAUTION
!Before making or changing the connections, switch off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
!When making connections, also keep the power cords of the devices being connected unplugged from the
power outlets.
!Depending on the device being connected (CD, DVD or BD player, etc.), the methods of connection and ter-
minal names may differ from the explanations in this manual. Also refer to the operating instructions of the
respective devices.
Rear panel
OUT
IN
AC IN
2
(HDZONE)
1
MAIN
(OUTPUT 5 V 0.9 A MAX)
(OUTPUT 12 V
TOTAL 150 mA MAX)
OPTICAL
COAXIAL
ASSIGNABLE
SELECTABLE
ASSIGNABLE
PRE OUT
1
2
(Single)
SUBWOOFER
1
2
L
R
DVR/BDR
IN
ZONE 2
PRE OUT
SAT/CBL
IN OUT
COMPONENT VIDEO
P B YP R
ANTENNA
CONTROL
AM LOOP
FM UNBAL 75
RS-232C
IR
12 V
TRIGGER
SPEAKERS
FRONTCENTER
A A
RL
SURROUND
RL
SURROUND BACKTOP MIDDLE /
RL
B
RL
6
-
1
IN
1
(CD)
1
BD
23 4 6
/MHL
1
(TV)
1
(SAT/CBL)
IN
1
(SAT/
CBL)
(SAT/CBL)(DVD)(
DVR/BDR)
ARC
HDMI OUT NETWORK
VIDEO/AUDIO
HDMI IN
DIGITAL IN
CONTROL
1
ASSIGNABLE
1
ASSIGNABLE
MONITOR OUT
SELECTABLE
1
Notes
!The RS-232C terminal is exclusively for the installer.
!The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input
Setup menu on page 48 to change the assignments if other connections are used.
Input function Input Terminals
HDMI Audio Component
BD (BD)
DVD IN 1
SAT/CBL IN 2 COAXIAL IN
DVR/BDR IN 3
HDMI 4 IN 4
HDMI 5
(front panel) IN 5
HDMI 6/MHL IN 6
TV OPTICAL
CD ANALOG-1

20
Connecting your equipment
03
Determining the speakers’ application
This unit permits you to build various surround systems, in accordance with the number of speakers you have.
!Be sure to connect speakers to the front left and right channels (Land R).
!It is also possible to only connect one of the surround back speakers (SB) or neither.
!If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
!When neither the top middle, surround back, or front wide speaker is connected, Dolby Atmos does not play.
Choose one from Plans [A] to [G] below.
Important
!The Speaker System setting must be made if you use any of the connections shown below other than [A] (see
Speaker system setting on page 94).
!The speakers from which sound is output can be switched according to the speaker layout/usage pattern
(sound is not necessarily output from all connected speakers). Use the OUT P. button to switch the speakers
from which sound is output. For details, see Switching the speaker terminals on page 75.
[A] 7.2 channel surround system (Surround back/Top middle) connection
*Default setting
!Speaker System setting: 7.2ch/5.2.2ch
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
A 7.2 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right
top middle speakers (TMdL/TMdR), the left and right surround speakers (SL/SR), the left and right surround back
speakers (SBL/SBR), and the subwoofers (SW 1/SW 2).
It is not possible to produce sound simultaneously from the surround back speakers and the top middle speakers.
This surround system produces a more true-to-life sound from above.
The speakers from which sound is output can be switched using the OUT P. button. For details, see Switching
the speaker terminals on page 75.
Playback of Dolby Atmos requires a connection with surround back speakers or top middle speakers.
[B] Dolby Enabled Speaker system connection
*Default setting
!Speaker System setting: 7.2ch/5.2.2ch
—Speaker Setting: Dolby Sp (Front)
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
—Speaker Setting: Dolby Sp (Surr)
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
7.2 ch surround system that consists of connected front left/right speakers (L/R), center speaker (C), left/right
surround speakers (SL/SR), left/right surround back speakers (SBL/SBR), subwoofer (SW 1/SW 2), Dolby Enabled
Speaker (TMdL/TMdR). For information on Dolby Enabled Speaker, refer to page 24.
Audio will not be output at the same time from the surround back speaker and a Dolby Enabled Speaker.
This surround system produces a more true-to-life sound from above.
The speakers from which sound is output can be switched using the OUT P. button. For details, see Switching
the speaker terminals on page 75.
Playback of Dolby Atmos requires a connection with surround back speakers or top middle speakers that use
Dolby Enabled Speakers.