Pioneer Super Tuner IIID MVH-P8200BT User manual
ORDER NO.
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2010
MVH-P8200BT/XNUC
CRT4530
MEDIA CENTER RECEIVER
MVH-P8200BT
/XNUC
MVH-P8200
/XNUC
RDS MEDIA CENTER RECEIVER
MVH-8200BT
/XNEW5
MVH-8200
/XNEW5
MEDIA CENTER RECEIVER
MVH-8250BT
/XNES
MVH-8250
/XNES
For details, refer to "Important Check Points for Good Servicing".
K-ZZZ FEB. 2010 Printed in Japan
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
CAUTION
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 3
5 678
5678
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
aSafe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 6
2. SPECIFICATIONS ............................................................................................................................................ 7
2.1 SPECIFICATIONS...................................................................................................................................... 7
2.2 DISC/CONTENT FORMAT ...................................................................................................................... 11
2.3 PANEL FACILITIES.................................................................................................................................. 12
2.4 CONNECTION DIAGRAM ....................................................................................................................... 14
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 20
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 20
3.2 PCB LOCATIONS .................................................................................................................................... 21
3.3 JIGS LIST ................................................................................................................................................ 22
4. BLOCK DIAGRAM.......................................................................................................................................... 24
5. DIAGNOSIS.................................................................................................................................................... 32
5.1 OPERATIONAL FLOWCHART ................................................................................................................ 32
5.2 ERROR CODE LIST ................................................................................................................................ 33
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 34
6. SERVICE MODE ............................................................................................................................................ 35
6.1 MONITOR TEST MODE .......................................................................................................................... 35
7. DISASSEMBLY............................................................................................................................................... 39
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 42
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 47
9.1 PACKING ................................................................................................................................................. 48
9.2 EXTERIOR............................................................................................................................................... 50
10. SCHEMATIC DIAGRAM ............................................................................................................................... 52
10.1 TUNER AMP UNIT [E.VOL PART] (GUIDE PAGE)(1/6) ........................................................................ 52
10.2 TUNER AMP UNIT [SYSTEM U-COM PART] (GUIDE PAGE)(2/6)....................................................... 58
10.3 TUNER AMP UNIT [DV5U PART] (GUIDE PAGE)(3/6) ......................................................................... 64
10.4 TUNER AMP UNIT [POWER SUPPLY PART](4/6)................................................................................ 70
10.5 TUNER AMP UNIT [I/F PART] (GUIDE PAGE)(5/6)............................................................................... 72
10.6 TUNER AMP UNIT [TUNER PART](6/6)................................................................................................ 78
10.7 PANEL PCB ........................................................................................................................................... 79
10.8 MONITOR PCB (GUIDE PAGE)............................................................................................................. 80
10.9 KEYBOARD PCB................................................................................................................................... 86
10.10 SD PCB and BT ANT PCB .................................................................................................................. 87
11. PCB CONNECTION DIAGRAM ................................................................................................................... 88
11.1 TUNER AMP UNIT................................................................................................................................. 88
11.2 PANEL PCB ........................................................................................................................................... 92
11.3 MONITOR PCB...................................................................................................................................... 94
11.4 KEYBOARD PCB................................................................................................................................... 98
11.5 SD PCB.................................................................................................................................................. 99
11.6 BT ANT PCB........................................................................................................................................ 100
12. ELECTRICAL PARTS LIST ........................................................................................................................ 101
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 5
5 678
5678
C
D
F
A
B
E
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
3. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during
power-on mode may damage the ICs inside the unit.
4. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector
is plugged or unplugged.
5. Countermeasures to user complaints on iPhone/iPod touch lip synchronization
When a video is replayed, the video and audio may be out of synchronization depending on the connected
iPod or iPhone.
If it is annoying, perform the following operation.
However, this operation will slightly deteriorate the sound quality of the iPod source.
Also, it will disable the ASR function when the iPod source is used.
[Default]
Audio digital mode
[Switching procedure]
Press BACK and UP and turn on Accessory simultaneously
The above switches the “Audio digital mode” to the “Audio analog mode”.
When the mode is switching, the BEEP1 sound will be heard.
[Supplement]
• The mode switching operation can only switch the “Audio digital mode” to the “Audio analog mode”.
(The BEEP1 sound will be heard every time.)
• No indication of the mode is provided.
[Resetting the mode]
Reset or BackUP OFF
The above resets the mode to the “Audio digital mode”.
6. Precautions for AEQ measurement
If the microphone is not connected securely, the microphone input signals may become inaccurate and an
error message “Plug the supplied microphone securely into the jack” may appear due to the measurement failure.
7. area and a heat sink becomes hot areas. Be careful not to burn yourself.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
6
1234
1234
C
D
F
A
B
E
1.2 NOTES ON SOLDERING
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 7
5 678
5678
C
D
F
A
B
E
2. SPECIFICATIONS
2.1 SPECIFICATIONS
Dimensions (W × H × D):
D
Chassis.....................178 mm × 50 mm × 162
mm
(7 in. × 2 in. × 6-3/8 in.)
Nose...........................188 mm × 58 mm × 17 mm
(7-3/8 in.× 2-1/4 in.× 5/8 in.)
Weight ..........................................1.01 kg (2.2 lbs)
(MVH-P8200BT)
Weight ..........................................0.99 kg (2.2 lbs)
(MVH-P8200)
Display
Screen size/aspect ratio....... 3.0 inch wide/16:9
(effective display area: 66.8
× 36.7 mm)
Pixels ........................................... 345 600 (1 440 × 240)
Display method ...................... TFT active matrix
Color system............................ NTSC compatible
Durable temperature range (power off)
.................................................. -4 °F to +176 °F
Audio
Maximum power output ....... 50 W × 4
70 W × 1/2 (for subwoo-
fer)
Continuous power output ...22 W × 4 (1 kHz, 5% THD, 4
load, both channels dri-
ven)
Load impedance ..................... 4 (4 to 8 (2 for 1
ch) allowable)
Preout maximum output level
................................................... 4.0 V
Equalizer (8-Band Graphic Equalizer):
Frequency......................... 40/80/200/400/1k/2.5k/8k/
10k Hz
Gain .................................... ±12 dB
HPF:
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–12 dB/oct
Subwoofer (mono):
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–18 dB/oct
Gain .................................... +6 dB to –24 dB
Phase ................................ Normal/Reverse
Bass boost:
Gain .....................................+12 dB to 0 dB
USB
USB standard specification
................................................... USB 1.1, USB 2.0 full speed
Maximum current supply ....500 mA
USB Class.................................. MSC (Mass Storage Class)
File system................................. FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
SD
Compatible physical format
....................................................Version 1.10
Maximum memory capacity
................................................... 2 GB
File system................................. FAT12, FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
FM tuner
Frequency range..................... 87.9 MHz to 107.9 MHz
Usable sensitivity.................... 9 dBf (0.8 μV/75 , mono,
S/N: 30 dB)
Signal-to-noise ratio.............. 72 dB (IHF-A network)
AM tuner
Frequency range..................... 530 kHz to 1 710 kHz (10
kHz)
Usable sensitivity.................... 25 μV (S/N: 20 dB)
Signal-to-noise ratio.............. 62 dB (analog broadcasting)
(IHF-A network)
Bluetooth
(MVH-P8200BT)
Version.........................................Bluetooth 2.0 certified
Output power ............................+4 dBm Max.
(Power class 2)
General
Power source............................ 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system.................. Negative type
Maximum current consumption
................................................... 10.0 A
Backup current.......................... 4.0 mA or less
MVH-P8200BT/XNUC, MVH-P8200/XNUC
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
8
1234
1234
C
D
F
A
B
E
CEA2006 Specifications
Power output .............................14 W RMS × 4 Channels (4
ohm and 1 % THD+N)
S/N ratio ......................................91 dBA (reference: 1 W into
4 ohm)
Note
Specifications and the design are subject to mod-
ifications without notice.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 9
5 678
5678
C
D
F
A
B
E
MVH-8200BT/XNEW5, MVH-8200/XNEW5
Dimensions (W × H × D):
DIN
Chassis.....................178 mm × 50 mm × 162
mm
Nose...........................188 mm × 58 mm × 17 mm
D
Chassis.....................178 mm × 50 mm × 162
mm
Nose...........................188 mm × 58 mm × 17 mm
Weight .........................................1.01 kg
(MVH-8200BT)
Weight .........................................0.99 kg
(MVH-8200)
Display
Screen size/aspect ratio....... 3.0 inch wide/16:9
(effective display area: 66.8
× 36.7 mm)
Pixels ............................................345 600 (1 440 × 240)
Display method ........................TFT active matrix
Color system............................. PAL/SECAM compatible
Durable temperature range (power off)
................................................... -20 °C to + 80 °C
Audio
Maximum power output ....... 50 W × 4
70 W × 1/2 (for subwoo-
fer)
Continuous power output ...22 W × 4 (1 kHz, 5% THD, 4
load, both channels dri-
ven)
Load impedance ......................4 (4 to 8 (2 for 1
ch) allowable)
Preout maximum output level
................................................... 4.0 V
Equalizer (8-Band Graphic Equalizer):
Frequency......................... 40/80/200/400/1k/2.5k/8k/
10k Hz
Gain .....................................±12 dB
HPF:
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–12 dB/oct
Subwoofer (mono):
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–18 dB/oct
Gain .....................................+6 dB to –24 dB
Phase .................................Normal/Reverse
Bass boost:
Gain .....................................+12 dB to 0 dB
USB
USB standard specification
....................................................USB 1.1, USB 2.0 full speed
Maximum current supply ....500 mA
USB Class.................................. MSC (Mass Storage Class)
File system................................. FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
SD
Compatible physical format
................................................... Version 1.10
Maximum memory capacity
................................................... 2 GB
File system................................. FAT12, FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
FM tuner
Frequency range......................87.5 MHz to 108.0 MHz
Usable sensitivity.....................9 dBf (0.8 μV/75 , mono,
S/N: 30 dB)
Signal-to-noise ratio...............72 d B (IEC -A network)
MW tuner
Frequency range..................... 531 kHz to 1 602 kHz (9 kHz)
Usable sensitivity.................... 25 μV (S/N: 20 dB)
Signal-to-noise ratio.............. 62 dB (IEC -A network)
LW tuner
Frequency range..................... 153 kHz to 281 kHz
Usable sensitivity.................... 28 μV (S/N: 20 dB)
Signal-to-noise ratio.............. 62 dB (IEC -A network)
Bluetooth
(MVH-8200BT)
Version.........................................Bluetooth 2.0 certified
Output power ........................... +4 dBm Max.
(Power class 2)
Note
Specifications and the design are subject to mod-
ifications without notice.
Backup current ..........................4.0 mA or less
General
Rated power source...............14.4 V DC
(allowable voltage range:
12.0 V to 14.4 V DC)
Grounding system...................Negative type
Maximum current consumption
....................................................10.0 A
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
10
1234
1234
C
D
F
A
B
E
MVH-8250BT/XNES, MVH-8250/XNES
Dimensions (W × H × D):
D
Chassis.....................178 mm × 50 mm × 162
mm
Nose...........................188 mm × 58 mm × 17 mm
Weight ..........................................1.01 kg
(MVH-8250BT)
Weight .........................................0.99 kg
(MVH-8250)
Display
Screen size/aspect ratio....... 3.0 inch wide/16:9
(effective display area: 66.8
× 36.7 mm)
Pixels ........................................... 345 600 (1 440 × 240)
Display method ....................... TFT active matrix
Color system............................. NTSC/PAL/PAL-M/SECAM
compatible
Durable temperature range (power off)
................................................... -20 °C to +80 °C
Audio
Maximum power output ....... 50 W × 4
70 W × 1/2 (for subwoo-
fer)
Continuous power output ...22 W × 4 (1 kHz, 5% THD, 4
load, both channels dri-
ven)
Load impedance ......................4 (4 to 8 (2 for 1
ch) allowable)
Preout maximum output level
................................................... 4.0 V
Equalizer (8-Band Graphic Equalizer):
Frequency......................... 40/80/200/400/1k/2.5k/8k/
10k Hz
Gain .....................................±12 dB
HPF:
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–12 dB/oct
Subwoofer (mono):
Frequency......................... 50/63/80/100/125 Hz
Slope...................................–18 dB/oct
Gain .....................................+6 dB to –24 dB
Phase .................................Normal/Reverse
Bass boost:
Gain .....................................+12 dB to 0 dB
USB
USB standard specification
................................................... USB 1.1, USB 2.0 full speed
Maximum current supply ....500 mA
USB Class.................................. MSC (Mass Storage Class)
File system................................. FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
SD
Compatible physical format
....................................................Version 1.10
Maximum memory capacity
................................................... 2 GB
File system................................. FAT12, FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format............ MPEG-4 AAC (iTunes en-
coded only)
(Ver. 8.2 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
FM tuner
Frequency range......................87.5 MHz to 108.0 MHz
Usable sensitivity.....................9 dBf (0.8 μV/75 , mono,
S/N: 30 dB)
Signal-to-noise ratio...............72 dB (IEC-A network)
AM tuner
Frequency range..................... 531 kHz to 1 602 kHz (9 kHz)
530 kHz to 1 640 kHz (10
kHz)
Usable sensitivity.................... 25 μV (S/N: 20 dB)
Signal-to-noise ratio...............62 dB (IEC-A network)
Bluetooth
(MVH-8250BT)
Version.........................................Bluetooth 2.0 certified
Output power ........................... +4 dBm Max.
(Power class 2)
Infrared remote control
Wavelength................................ 945 nm
Output ......................................... typ; 10 mw/sr per Infrared
LED
Note
Specifications and the design are subject to mod-
ifications without notice.
General
Rated power source...............14.4 V DC
(allowable voltage range:
12.0 V to 14.4 V DC)
Grounding system...................Negative type
Maximum current consumption
....................................................10.0 A
Backup current ..........................4.0 mA or less
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 11
5 678
5678
C
D
F
A
B
E
2.2 DISC/CONTENT FORMAT
(UC model only)
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.
(BT model only)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
12
1234
1234
C
D
F
A
B
E
2.3 PANEL FACILITIES
Head unit
traPtraP
HOME
AUX input jack (3.5
mm stereo/video
jack)
Microphone input
jack for auto EQ
measurement
SRC/OFF (back/display
off)
MULTI-CONTROL
(M.C.)Detach button
USB port
SD memory card
slot
Remove the front
panel to access the
SD memory card
slot.
CAUTION
Use an optional Pioneer USB cable (CD-U50E) to
connect the USB audio player/USB memory as
any device connected directly to the unit will pro-
trude out from the unit and may be dangerous.
Do not use unauthorized products.
Remote control
MVH-P8200/UC, MVH-P8250BT/ES
MVH-P8250/ES
The “EW” models separately sells re-
mote control CD-R320.
Only for MVH-P8200BT/UC.
Part Operation
+/–(VO-
LUME)
Press to increase or decrease vo-
lume.
MUTE Press to mute. Press again to un-
mute.
/ / /
Press to perform manual seek
tuning, fast forward, reverse and
track search controls. Also used
for controlling functions.
AUDIO Press to select an audio function.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 13
5 678
5678
C
D
F
A
B
E
Part Operation
dDISP/SCRL
Press to select different displays
for the audio source.
Press to select the basic screen or
image screen for the video
source.
• If the background setting on
the entertainment menu is
turned off, you can switch be-
tween the basic screen and
image screen.
ePress to pause or resume play-
back.
fFUNCTION Press to select functions.
gLIST/
ENTER
Press to display the list depending
on the source.
While in the operating menu,
press to control functions.
hBAND/ES-
CAPE
Press to select among three FM
bands and one AM band.
When playing external storage de-
vices containing a mixture of var-
ious media file types, press to
switch between media file types
to play.
Music(compressed audio) —
Video (DivX video files) — Photo
(JPEG picture files)
Press to return to the ordinary dis-
play from the list/function menu.
Press to cancel the initial setting
menu.
iThumb pad
Move to perform manual seek
tuning, fast forward, reverse and
track search controls. Also used
for controlling functions.
Functions are the same as M.C.
except for volume control.
Press to display the folder list, file
list or preset channel list depend-
ing on the source.
jDIRECT Press to directly select the desired
channel for XM/SIRIUS tuner.
kClear Press to cancel the input number
when 0to 9are used.
Part Operation
l0to 9but-
tons
Press to directly select the desired
channel or preset tuning. Buttons
1to 6can operate the preset tun-
ing.
Press and hold one of the buttons
1to 6to preset the desired sta-
tion.
mOFF
HOOK
Press to start talking on the
phone while operating a phone.
nON HOOK
While operating the phone
source, press to end a call or re-
ject an incoming call.
oPGM
Press to operate the prepro-
grammed functions for each
source. (Refer to Using the PGM
button in Operation manual.)
Basic Operations
Important
• Handle gently when removing or attaching
the front panel.
• Avoid subjecting the front panel to excessive
shock.
• Keep the front panel out of direct sunlight and
high temperatures.
• To avoid damage to the device or vehicle inter-
ior, remove any cables and devices attached
to the front panel before detaching it.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
14
1234
1234
C
D
F
A
B
E
2.4 CONNECTION DIAGRAM
Connecting the power cord
Yellow
Connect to the constant 12 V supply terminal.
Fuse resistor
Red
Connect to terminal controlled by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Left Right
Front speakerFront speaker
Rear speaker or
Subwoofer (4 )
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Violet
Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 ), be sure to connect with Violet and Violet/black leads of this unit. Do not
connect anything to Green and Green/black leads.
Subwoofer (4 )
× 2
Rear speaker or
Subwoofer (4 )
Fuse (10 A)
Antenna input
Orange/white
Connect to lighting switch terminal.
Fuse resistor
This product
IP-BUS cable
IP-BUS input
(Blue)
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking
brake. This lead must be connected to the power
supply side of the parking brake switch.
Blue/white
Connect to system control terminal of the power amp or
auto-antenna relay control terminal (max. 300 mA 12 V DC).
Ground side
Power supply side
Parking brake
switch
With a 2 speaker system, do not connect anything to the speaker leads
that are not connected to speakers.
Note:
· Change the initial setting of this unit (refer
to the Operation Manual). The subwoofer
output of this unit is monaural.
4 m (13 ft. 1 in.)
Microphone
(MVH-P8200BT only)
Wired remote input
Hard-wired remote control adaptor can be connected
(sold separately).
Pioneer IP-BUS
accessories
(sold separately)
Microphone input
(MVH-P8200BT only)
MVH-P8200BT/XNUC, MVH-P8200/XNUC
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 15
5 678
5678
C
D
F
A
B
E
When connecting to separately sold power amp
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control
terminal. (max. 300 mA 12 V DC).
This product
Connect with RCA cables
(sold separately)
Rear speaker
Perform these connections when
using the optional amplifier.
System remote control
Front speakerFront speaker
thgiRtfeL
Front output
Rear speaker
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Subwoofer Subwoofer
Rear output
Subwoofer output
To front output
To rear output
To subwoofer
output
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
16
1234
1234
C
D
F
A
B
E
Connecting the power cord
Orange/white
Connect to lighting switch terminal.
Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
Note:
Depending on the kind of vehicle, the
function of 2* and 4* may be different. In
this case, be sure to connect 1* to 4* and
3* to 2*.
1*
3*
2*
4*
Yellow (2*)
Back-up
(or accessory)
Yellow (1*)
Connect to the constant 12 V
supply terminal.
Connect leads of the same
color to each other.
Fuse (10 A)
Fuse resistor
Red (4*)
Accessory
(or back-up)
Red (3*)
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
This product
Antenna input
Fuse resistor
Notes:
· Change the initial setting of this unit (refer to the Operation Manual).
The subwoofer output of this unit is monaural.
· When using a subwoofer of 70 W (2 ) , be sure to connect with
Violet and Violet/black leads of this unit. Do not connect anything to
Green and Green/black leads.
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Yellow/black
If you use equipment with Mute function, wire this lead to the
Audio Mute lead on that piece of equipment. If not, keep the
Audio Mute lead free of any connections.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
connector will differ depending
on the type of vehicle. Connect
5* and 6* when Pin 5 is an
antenna control type. In other
types of vehicles, never connect
5* and 6*.
Blue/white (5*)
Ground side
Power supply side
Parking brake
switch
4 m
Microphone
(MVH-8200BT only)
Wired remote input
Hard-wired remote control
adaptor can be connected (sold
separately).
Microphone input
(MVH-8200BT only)
MVH-8200BT/XNEW5, MVH-8200/XNEW5
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 17
5 678
5678
C
D
F
A
B
E
When connecting to separately sold power amp
Blue/white
Connect to system control
terminal of the power amp
(max. 300 mA 12 V DC).
Blue/white (6*)
Connect to auto-antenna
relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO connector will
differ depending on the type of vehicle.
Connect 5* and 6* when Pin 5 is an
antenna control type. In other types of
vehicles, never connect 5* and 6*.
Blue/white (5*)
This product
Connect with RCA cables
(sold separately)
Rear speaker
Perform these connections when
using the optional amplifier.
System remote control
rekaepstnorFrekaepstnorF
thgiRtfeL
Front output
Rear speaker
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Subwoofer Subwoofer
Rear output
Subwoofer output
To front output
To rear output
To subwoofer
output
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
18
1234
1234
C
D
F
A
B
E
7. Yellow
Connect to the constant 12 V supply terminal.
11. Fuse resistor
9. Red
Connect to terminal controlled by ignition switch (12 V DC).
10. Black (chassis ground)
Connect to a clean, paint-free metal location.
17. Left 18. Right
rekaepstnorF.21rekaepstnorF.21
19. Rear speaker or
Subwoofer (4 )
19. Rear speaker or
Subwoofer (4 )
13. White 15. Gray
16. Gray/black14. White/black
20. Green 22. Violet
21. Green/black 23. Violet/black
20. Green 22. Violet
21. Green/black 23. Violet/black
25. Not used.
24. When using a subwoofer of 70 W (2 ), be sure to connect with Violet and Violet/black leads of this unit.
Do not connect anything to Green and Green/black leads.
26. Subwoofer (4 )
× 2
5. Fuse (10 A)
6. Antenna input
8. Orange/white
Connect to lighting switch terminal.
11. Fuse resistor
1. This product
27. Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
28. Light green
Used to detect the ON/OFF status of the parking
brake. This lead must be connected to the power
supply side of the parking brake switch.
32. Blue/white
Connect to system control terminal of the power amp or
auto-antenna relay control terminal (max. 300 mA 12 V DC).
31. Ground side
29. Power supply side
30. Parking brake
switch
33. With a 2 speaker system, do not connect anything to the speaker
leads that are not connected to speakers.
34. Note:
· Change the initial setting of this unit (refer
to the Operation Manual). The subwoofer
output of this unit is monaural.
4 m 3. Microphone
(MVH-8250BT only)
4. Wired remote input
Hard-wired remote control adaptor can be connected
(sold separately).
2. Microphone input
(MVH-8250BT only)
MVH-8250BT/XNES, MVH-8250/XNES
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC 19
5 678
5678
C
D
F
A
B
E
32. Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control
terminal. (max. 300 mA 12 V DC).
1. This product
41. Connect with RCA cables
(sold separately)
45. Rear speaker
46. Perform these connections
when using the optional amplifier.
43. System remote control
12. Front speaker 12. Front speaker
17. Left 18. Right
36. Front output
45. Rear speaker
42. Power amp
(sold separately)
42. Power amp
(sold separately)
42. Power amp
(sold separately)
44. Subwoofer 44. Subwoofer
35. Rear output
37. Subwoofer output
39. To front output
38. To rear output
40. To subwoofer
output
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
MVH-P8200BT/XNUC
20
1234
1234
C
D
F
A
B
E
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
To keep the product quality after servicing, please confirm following check points.
demrifnocebotmetIserudecorP.oN
1 Confirm whether the customer complain has
been solved.
If the customer complain occurs with the
specific media, use it for the operation check.
The customer complain must not be
reappeared.
Display, audio and operations must be
normal.
2 FM/AM tuner Check FM/AM tuner action.
(Seek, Preset)
Switch band to check both FM and AM.
Display, audio and operations must be
normal.
retfaecnaraeppastinotridrosehctarcsoNkcehcecnaraeppA3
receiving it for service.
See the table below for the items to be checked regarding audio:
Item to be checked regarding audio
Distortion
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
Other manuals for Super Tuner IIID MVH-P8200BT
2
This manual suits for next models
5
Table of contents
Other Pioneer Receiver manuals
Pioneer
Pioneer VSX-827-K User manual
Pioneer
Pioneer VSX-932 Installation guide
Pioneer
Pioneer VSX-D337 User manual
Pioneer
Pioneer VSX-504S User manual
Pioneer
Pioneer AVH-P5900DVD User manual
Pioneer
Pioneer VSX-915 User manual
Pioneer
Pioneer VSX-1012-K User manual
Pioneer
Pioneer VSX-LX302 Installation guide
Pioneer
Pioneer XV-DV303 User instructions
Pioneer
Pioneer VSX-1122-K User manual
Pioneer
Pioneer Elite SC-27 User manual
Pioneer
Pioneer VSX91TXH - Elite AV Receiver User manual
Pioneer
Pioneer Elite SC-61 User manual
Pioneer
Pioneer DVR-720H-S Building instructions
Pioneer
Pioneer CX-3287 User manual
Pioneer
Pioneer VSX-S300-k User manual
Pioneer
Pioneer VSX-1120-K User manual
Pioneer
Pioneer AVH-279BT User manual
Pioneer
Pioneer VSX-1019AH User manual
Pioneer
Pioneer AirWare xm2go User manual
