Pioneer VSX-930-K User manual

Operating Instructions
AV Receiver
VSX-930-K
VSX-830-K

2
WARNING
This equipment is not waterproof
. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
To
prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE
R-SERVICEABLE
PA
RTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
D3-4-2-1-1_B1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).
D3-4-2-1-7c*_A2_En
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
D8-9-2-5_A1_En
5 GHz band is restricted to indoor operations only.
D8-9-2-6_A1_En
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediatel
y.
D41-6-4_A1_En
VENTILATION CAUTION
In case of VSX-930
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 40 cm at top, 10 cm at rear
, and 20 cm at each
side).
In case of VSX-830
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 40 cm at top, 20 cm at rear
, and 20 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating.
To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
Voltage selector
VSX-830 onl
y
Y
ou can find the voltage selector switch on the rear
panel of multi-voltage models.
The factory setting for the voltage selector is 220 -
240
V. Please set it to the correct voltage for your
country or r
egion.
• F
or Taiwan, please set to 110 - 127 V before using.
Before changing the voltage, disconnect the AC power
cord. Use a medium size screwdriver to change the
voltage selector switch
.
Medium size screwdriver
D3-4-2-1-5*_A2_En
VOLTAGE SELECTOR
110 - 127 V220 - 240 V

3
Thank you for buying this Pioneer product. Please read through these operating instruc-
tions so you will know how to operate your model properly.
Contents
01 Before you start
Features...............................................................................................................................................................................7
Checking what’s in the box................................................................................................................................................9
Installing the receiver.......................................................................................................................................................10
Loading the batteries........................................................................................................................................................10
Operating range of remote control unit..........................................................................................................................10
02 Controls and displays
Remote control (In case of VSX-930) ..............................................................................................................................12
Remote control (In case of VSX-830) ..............................................................................................................................13
Display ...............................................................................................................................................................................15
Front panel ........................................................................................................................................................................16
03 Connecting your equipment (In case of VSX-930)
Connecting your equipment............................................................................................................................................19
Rear panel .........................................................................................................................................................................19
Determining the speakers’ application ..........................................................................................................................20
Placing the speakers........................................................................................................................................................22
Connecting the speakers.................................................................................................................................................23
Installing your speaker system........................................................................................................................................23
About the audio connection ............................................................................................................................................26
About the video converter................................................................................................................................................26
About HDMI ......................................................................................................................................................................27
Connecting your TV and playback components ............................................................................................................27
Connecting a satellite/cable receiver or other set-top box ...........................................................................................29
Connecting other audio components.............................................................................................................................30
Connecting additional amplifiers....................................................................................................................................31
Connecting AM/FM antennas.........................................................................................................................................31
Making MULTI-ZONE connections .................................................................................................................................32
Connecting to the network through LAN interface .......................................................................................................34
Connecting an iPod..........................................................................................................................................................34
Connecting a USB device................................................................................................................................................34
Connecting an MHL-compatible device.........................................................................................................................35
Connecting an HDMI-equipped component to the front panel input .........................................................................35
Connecting an IR receiver ...............................................................................................................................................35
Plugging in the receiver ...................................................................................................................................................36
04 Connecting your equipment (In case of VSX-830)
Connecting your equipment............................................................................................................................................38
Rear panel .........................................................................................................................................................................38
Determining the speakers’ application ..........................................................................................................................38
Placing the speakers........................................................................................................................................................39
Connecting the speakers.................................................................................................................................................40
Installing your speaker system........................................................................................................................................40
About the audio connection ............................................................................................................................................41
About HDMI ......................................................................................................................................................................42
Connecting your TV and playback components ............................................................................................................42
Connecting a satellite/cable receiver or other set-top box ...........................................................................................44
Connecting other audio components.............................................................................................................................45
Connecting the subwoofer ..............................................................................................................................................45
Connecting AM/FM antennas.........................................................................................................................................45
Connecting to the network through LAN interface .......................................................................................................46
Connecting an iPod..........................................................................................................................................................47
Connecting a USB device................................................................................................................................................47
Connecting an MHL-compatible device.........................................................................................................................47
Plugging in the receiver ...................................................................................................................................................47
05 Basic Setup
Initial settings of this receiver..........................................................................................................................................49
Setting with a special application (Start-up Navi) .........................................................................................................49
Perform settings using the AVNavigator built into this receiver..................................................................................49
Setting by referring to the operating instructions .........................................................................................................51
06 Basic playback
Playing a source ...............................................................................................................................................................62
Playing an iPod .................................................................................................................................................................63
Playing a USB device .......................................................................................................................................................64
Playing an MHL-compatible device ................................................................................................................................65
Listening to the radio........................................................................................................................................................66
Music playback using Bluetooth wireless technology ..................................................................................................67
07 Listening to your system
Enjoying various types of playback using the listening modes....................................................................................70
Selecting MCACC presets ...............................................................................................................................................72
Choosing the input signal................................................................................................................................................72
Better sound using Phase Control..................................................................................................................................72
Better sound using Phase Control and Full Band Phase Control ...............................................................................73
08 Playback with NETWORK features
Introduction.......................................................................................................................................................................75
Playback with Network functions....................................................................................................................................76
About network playback...................................................................................................................................................78
About playable file formats..............................................................................................................................................80

4
09 Control with HDMI function
About the Control with HDMI function...........................................................................................................................82
Making Control with HDMI connections........................................................................................................................82
HDMI Setup.......................................................................................................................................................................82
Before using synchronization..........................................................................................................................................83
About synchronized operations ......................................................................................................................................83
Sound Retriever Link ........................................................................................................................................................83
Cautions on the Control with HDMI function ................................................................................................................83
10 Using other functions
Setting the Audio options ................................................................................................................................................85
Setting the Video options.................................................................................................................................................87
Switching the output (OUTPUT PARAMETER)..............................................................................................................87
HDMI 4K/60p signal input setting...................................................................................................................................88
Changing the channel level while listening ...................................................................................................................88
Using the MULTI-ZONE controls.....................................................................................................................................89
Network settings from a web browser............................................................................................................................89
Using the sleep timer .......................................................................................................................................................89
Dimming the display ........................................................................................................................................................90
Checking your system settings .......................................................................................................................................90
Resetting the system........................................................................................................................................................91
11 Controlling the rest of your system (VSX-930 only)
About the Remote Setup menu.......................................................................................................................................93
Operating multiple receivers ...........................................................................................................................................93
Setting the remote to control other components..........................................................................................................93
Selecting preset codes directly .......................................................................................................................................93
Programming signals from other remote controls .......................................................................................................94
Erasing one of the remote control button settings........................................................................................................94
Erasing all learnt settings that are in one input function .............................................................................................95
Using All Zone Standby....................................................................................................................................................95
Setting the switching time for the receiver operation mode ........................................................................................95
Resetting the remote control settings............................................................................................................................95
Controlling components ..................................................................................................................................................96
12 The MCACC PRO (VSX-930)/Advanced MCACC (VSX-830) menu
Making receiver settings from the MCACC PRO (VSX-930)/Advanced MCACC (VSX-830) menu............................99
Automatic MCACC (Expert).............................................................................................................................................99
Manual MCACC setup ...................................................................................................................................................101
Checking MCACC Data..................................................................................................................................................103
Data Management..........................................................................................................................................................104
13 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu.............................................................................................106
Manual speaker setup....................................................................................................................................................106
MHL Setup ......................................................................................................................................................................109
The Other Setup menu...................................................................................................................................................109
Making network settings using Safari..........................................................................................................................111
Using Safari to set a friendly name...............................................................................................................................112
Using Safari to update the firmware.............................................................................................................................112
14 FAQ
Troubleshooting..............................................................................................................................................................114
Power...............................................................................................................................................................................114
No sound .........................................................................................................................................................................114
Other audio problems ....................................................................................................................................................115
BT AUDIO ........................................................................................................................................................................116
Video ................................................................................................................................................................................116
Settings............................................................................................................................................................................116
Professional Calibration EQ graphical output.............................................................................................................117
Display .............................................................................................................................................................................117
Remote control ...............................................................................................................................................................117
HDMI................................................................................................................................................................................118
MHL..................................................................................................................................................................................119
Built-in AVNavigator.......................................................................................................................................................119
USB interface..................................................................................................................................................................119
iPod ..................................................................................................................................................................................120
Network ...........................................................................................................................................................................120
Wireless LAN...................................................................................................................................................................122
15 Additional information
About Wi-Fi®....................................................................................................................................................................124
SABRE DACTM.................................................................................................................................................................124
About HDMI ....................................................................................................................................................................124
HTC Connect...................................................................................................................................................................124
About iPod.......................................................................................................................................................................124
Windows 8.......................................................................................................................................................................125
MHL..................................................................................................................................................................................125
About Bluetooth wireless technology ...........................................................................................................................125
Software license notice..................................................................................................................................................125
Surround sound formats ...............................................................................................................................................127
Auto Surround, ALC and Stream Direct with different input signal formats............................................................127
Speaker Setting Guide....................................................................................................................................................128
About messages displayed when using network functions.......................................................................................129
Important information regarding the HDMI connection ............................................................................................130
Cleaning the unit ............................................................................................................................................................130
Pioneer Authorized Distributors ...................................................................................................................................130
Glossary ...........................................................................................................................................................................131
Features index.................................................................................................................................................................133
Specifications .................................................................................................................................................................134
Preset code list................................................................................................................................................................136

5
Flow of settings on the receiver
Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used eas-
ily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 8, 10
Setting to be made as necessary: 6, 7, 9, 11, 12, 13, 14
Important
Using Wiring Navi on AVNavigator of this receiver, you can make the initial settings of the receiver on your com-
puter or mobile device. In that case, you can use Wiring Navi to make the same connections or settings that are
performed in Steps 2, 3, 4, 5, 6, 8, and 9. For details of how to use AVNavigator, refer to How to use the built-in
AVNavigator on page 49.
1 Before you start
!Checking what’s in the box on page 9
!Loading the batteries on page 10
j
2 Determining the speakers’ application (page 20 (VSX-930), page 38 (VSX-830))
In case of VSX-930
![A] 7.2 channel surround system (Surround back/Top middle) connection
![B] Dolby Enabled Speaker system connection
![C] 7.2 channel surround system (Surround back/Front wide) connection
![D] 7.2 channel surround system & Speaker B connection
![E] 5.2 channel surround system & Front Bi-amping connection (High quality surround)
![F] 5.2 channel surround system & HDZONE connection (Multi Zone)
In case of VSX-830
![A] 5.2 channel surround system connection
![B] Front Bi-amping connection (High quality surround)
j
3 Connecting the speakers
!Placing the speakers (page 22 (VSX-930), page 39 (VSX-830))
!Connecting the speakers (page 23 (VSX-930), page 40 (VSX-830))
!Installing your speaker system (page 23 (VSX-930), page 40 (VSX-830))
!Bi-amping your speakers (page 25 (VSX-930), page 41(VSX-830))
j
4 Connecting the components
!About the audio connection (page 26 (VSX-930), page 41 (VSX-830))
!VSX-930 only: About the video converter on page 26
!Connecting your TV and playback components (page 27 (VSX-930), page 42 (VSX-830))
!Connecting AM/FM antennas (page 31 (VSX-930), page 45 (VSX-830))
!Plugging in the receiver (page 36 (VSX-930), page 47 (VSX-830))
j
5 Power On
j
6 Making the initial settings according to the region and environment in which you live
!Changing the TV format setting (page 60)
!Changing the frequency step (page 60)
!Changing the OSD display language (OSD Language) (page 60)
j
7 Using the AVNavigator functions (page 49)
j
8 MCACC speaker settings
!Automatically conducting optimum sound tuning (Full Auto MCACC) on page 57
j
9 The Input Setup menu (page 59)
(When using connections other than the recommended connections)
j
10 Basic playback (page 61)
j
11 Switching the HDMI output (page 88)
j
12 Adjusting the sound and picture quality as desired
!Using the various listening modes (page 69)
!Better sound using Phase Control (page 72)
!Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 99)
!Changing the channel level while listening (page 108)
!Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 85)
!Setting the Audio options (page 85)
!Setting the Video options (page 87)
j
13 Other optional adjustments and settings
!Control with HDMI function (page 81)
!The Advanced MCACC menu (page 98)
!The System Setup and Other Setup menus (page 105)
j
14 Making maximum use of the remote control
!Operating multiple receivers (page 93)
!Setting the remote to control other components (page 93)

6
Features............................................................................................................................................ 7
Checking what’s in the box ............................................................................................................9
Installing the receiver....................................................................................................................10
Loading the batteries ....................................................................................................................10
Operating range of remote control unit...................................................................................... 10
Before you start

7
Before you start
01
Features
Audio
%Dolby Atmos
VSX-930 only
This AV receiver supports the latest Dolby Atmos surround sound system. Dolby Atmos is a new technology in
which, through real time calculation of audio data and meta data (position and time information) included in the
audio signal, a surround sound space is achieved irrespective of the speaker layout and number of speakers.
Dolby Atmos contents are required to enjoy Dolby Atmos. For Blu-ray discs with Dolby Atmos, Dolby Atmos can
be played by connecting most conventional Blu-ray discs with this receiver using HDMI.
%ESS-24bit-DAC-equipped
VSX-930 only
All channels are equipped with ESS SABRE Premier Audio DACs. The Jitter Eliminators achieve clearer sound.
%Hi-bit 24 Audio Processing
VSX-930 only
Creates a wider dynamic range with digital sources like CDs or DVDs. 16- and 20-bit PCM as well as compressed
audio is requantized to 24 bits, and the high frequency component is interpolated upon data processing to enable
smoother, more subtle musical expression.
%Easy setup using MCACC PRO (VSX-930)/Advanced MCACC (VSX-830)
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced fea-
tures of Professional Acoustic Calibration EQ.
%Auto Phase Control Plus
For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first
place. This function automatically corrects phase shifting on such discs and broadcasts. This function is particu-
larly effective when playing multi-channel music containing low frequency effects (LFE).
%Full Band Phase Control
VSX-930 only
The further advanced Full Band Phase Control technology focuses on the group delay in the speaker network
filter, and compensates with special digital signal processing (DSP), to adjust the phase of each unit as well as
the group delay for each speaker. Full Band Phase Control gives multi-range speakers the sound coherence of
full-range speakers, while retaining the wide frequency range advantage.
%Subwoofer EQ
The EQ for subwoofer output can be corrected. In addition to the results of MCACC automatic adjustment, the
subwoofer output can be adjusted to match the viewing environment or your taste by manual correction.
%Virtual Speakers
By turning on the ‘Virtual Surround Back’, ‘Virtual Height’, and ‘Virtual Wide’ modes, it is possible to realize a
maximum of 11.1 channels combining the speakers that are actually installed and the virtual speakers. This
makes for a smoother connection between the sounds and an improved 3D feel.
Video
%Ultra HD (with 4K/60p video support) - Pass-through and upscaling -
Up to 4K/60p resolution images can be passed through and displayed as such, and the HD (High Definition) or
Full HD images of DVDs, Blu-ray discs and HD broadcasts can be upscaled to a resolution of up to 4K/60p and
displayed. A separate monitor supporting Ultra HD (4K video) is required.
%HDMI (4K/60p, 3D, Audio Return Channel)
A compatible component is required to use the above function.
%HDCP 2.2
This receiver is compatible with the HDCP 2.2 standard, which has stringent copyright protection technology.

8
Before you start
01
Network
%Built-in Wi-Fi
This receiver is compatible with Wi-Fi standards, and supports the 2.4 GHz and 5 GHz dual bands.
%Wireless Direct
With this receiver, you can enjoy music playback without a router by direct wireless connection using an iPhone
or other Wi-Fi mobile device.
%Spotify Connect
Spotify is a digital music-streaming service that gives you access to millions of songs instantly. This receiver is
ready for Spotify Connect, which lets you play music on your audio system, using the Spotify app as a remote. For
service availability in your country check www.spotify.com.
%Compatible with Windows 8.1
This receiver is compatible with Windows 8.1, letting you easily stream music from compatible PCs on your home
network.
%Apple AirPlay
With AirPlay you can stream music from iTunes to this receiver and play it through your home theater system.
You can even use the receiver to view metadata including song titles, artist’s names as well as the album art on a
connected display. You can easily enjoy your iTunes music in any room in the house.
%DLNA Certified (1.5)
This receiver is a DLNA certified (1.5) device, enabled to work not only as a DMP (Digital Media Player) for playing
DMS (Digital Media Server) audio files, but also as a DMR (Digital Media Renderer) to be controlled remotely by a
device such as a smartphone or PC.
%Internet Radio
When you connect this receiver to the network, you can listen to internet radio from around the world. You can
register your favorite broadcasting stations in this receiver.
%Multi-channel Music File playback
This receiver enables multi-channel music file playback with a resolution of up to 96 kHz/24 bit. Playback of WAV
and FLAC files via the front USB port and network is supported.
%DSD File Music playback (via Network, Front USB and HDMI)
Playback of high sound quality DSD music (DSD files and DSD discs (SACDs)) is supported.
%High Resolution Music Playback
High resolution music files with resolutions of 96 kHz/24 bit to 192 kHz/24 bit can be played. Playback of AIFF,
Apple Lossless, WAV and FLAC files via the front USB port and network is supported.
%Gapless Playback
The silent section between tracks is skipped when playing music files, eliminating the interruptions that usually
occur when playing live or concert contents.
This receiver plays back AAC or MP3 format files with a minimum gap even though it is fundamentally impossible
to play back without a gap.
Connectivity
%Built-in Bluetooth Wireless Technology
This receiver, equipped with Bluetooth wireless technology, lets you enjoy music files on an iPhone or other
Bluetooth wireless technology enabled device wirelessly.
%MHLTM (Mobile High-definition Link)-compatible device playback
An incorporates MHL 2 mobile device can be connected to enjoy 3D videos, full-HD videos, high quality multi-
channel audio, and photos etc., with charge the battery on the receiver.
%HTC Connect
HTC Connect makes it easy to wirelessly stream your favorite music straight from your HTC phone. There’s no
need for a separate app; HTC Connect is built right in your phone’s music player.
%iPod Playback
Your iPod and iPhone can be connected to the receiver’s USB terminal to play the music files on the iPod or
iPhone. Also, the iPod or iPhone is charged when it is connected to the receiver.

9
Before you start
01
Installation
%Built-in AVNavigator
With the built-in AVNavigator embedded in this receiver, Wiring Navi can be used to interactively connect and
set initial settings of this receiver with a smart phone, tablet, PC, and Mac through a home network. In addition,
with VSX-930, Interactive Operation Guide can also be used, which visually explains the functions and opera-
tion by actually experiencing the operation with contents linked with the main device.
%iControlAV5 Remote Application
This is an application that allows intuitive operation of many of the receiver’s functions. This application is avail-
able on the App Store for iPhone, iPod touch and iPad. You can also get it on Google Play for Android smart-
phones. The application can be downloaded free of charge.
%HDZONE output
VSX-930 only
This receiver supports output of the HDMI output to a subzone room. Powerful images can be enjoyed simply by
connecting this receiver to a TV supporting 4K/Full-HD/3D. In addition, a multi-channel environment can be cre-
ated by connecting this receiver to another AV receiver in the subzone room.
%ZONE Ready
VSX-930 only
This receiver is equipped with HDZONE. HDZONE supports HD audio/video streaming to a separate room via
HDMI. Multi-Zone enables music and movie playback from different sources in three zones at the same time.
%Energy Saving Design
This AV receiver has an ecological design. In addition to even lower power consumption in standby, the receiver
is equipped with an ‘eco mode’ for low power consumption when playing contents as well. Furthermore, the eco
mode can easily be set with a dedicated button on the remote control of using iControlAV5.
Checking what’s in the box
Please check that you’ve received the following supplied accessories:
!Setup microphone (cable: 5 m)
!Remote control unit
!AAA size IEC R03 dry cell batteries (to confirm system operation) x2
!AM loop antenna
!FM wire antenna
!Power cord
!CD-ROM
!Quick start guide
!Safety Brochure
Note
The operating instructions explains the operation using mainly illustrations of VSX-930. In addition, the illustra-
tions are modified and simplified for explanation purposes and may be different from the actual product.
Handling the CD-ROM
Precautions For Use
!This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.
License
!Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
!Copyright to data provided on this CD-ROM belongs to PIONEER HOME ELECTRONICS CORPORATION.
Unauthorized transfer, duplication, broadcast, public transmission, translation, sales, lending or other such
matters that go beyond the scope of “personal use” or “citation” as defined by Copyright Law may be subject to
punitive actions. Permission to use this CD-ROM is granted under license by PIONEER HOME ELECTRONICS
CORPORATION.
General Disclaimer
!PIONEER HOME ELECTRONICS CORPORATION does not guarantee the operation of this CD-ROM with
respect to personal computers using any of the applicable OS. In addition, PIONEER HOME ELECTRONICS
CORPORATION is not liable for any damages incurred as a result of use of this CD-ROM and is not responsible
for any compensation. The names of private corporations, products and other entities described herein are the
registered trademarks or trademarks of their respective firms.

10
Before you start
01
Installing the receiver
!When installing this unit, make sure to put it on a level and stable surface.
!Don’t install it on the following places:
—on a color TV (the screen may distort)
—near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
—in direct sunlight
—in damp or wet areas
—in extremely hot or cold areas
—in places where there is vibration or other movement
—in places that are very dusty
—in places that have hot fumes or oils (such as a kitchen)
!Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.
Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We rec-
ommend using alkaline batteries that have a longer life.
!The remote control setting may be restored to the default after the batteries are replaced. If this happens, reset
it (page 92 (VSX-930), page 13 (VSX-830)).
VSX-930
VSX-830
WARNING
!Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or perfor-
mance of batteries.
CAUTION
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
!Never use new and old batteries together.
!Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
!When inserting the batteries, make sure not to damage the springs on the battery’s (–) terminals. This can
cause batteries to leak or overheat.
!Batteries with the same shape may have different voltages. Do not use different batteries together.
!When disposing of used batteries, please comply with governmental regulations or environmental public insti-
tution’s rules that apply in your country/area.
These symbols are only valid
in the European Union.
K058c_A1_En
(Symbol examples for batteries)
Pb
Operating range of remote control unit
The remote control may not work properly if:
!There are obstacles between the remote control and the receiver’s remote sensor.
!Direct sunlight or fluorescent light is shining onto the remote sensor.
!The receiver is located near a device that is emitting infrared rays.
!The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m

11
Remote control (In case of VSX-930)............................................................................................ 12
Remote control (In case of VSX-830)............................................................................................ 13
Display............................................................................................................................................15
Front panel.....................................................................................................................................16
Controls and displays

12
Controls and displays
02
Remote control (In case of VSX-930)
This section explains how to operate the remote control for the receiver.
RECEIVER
D.ACCESS
DIMMER SLEEP
RCU SETUP
MPX
PRESET TUNE
BAND PTY
iPod
TUNER
INPUT
USB ADPTROKU
BT
TV
TV
MHL
CD
OUT P.
DVDBD
ALL ZONE STBY
SOURCE
STANDBY/ON
MAIN
SAT
SUB ZONE CONTROL
SOURCE CONTROL
MUTE
VOLUME
VOL
TOP
MENU
HOME
MENU
TOOLS
MENU
ENTER
RETURN
CLASS
ENTER CLR
CH
CH
2
546
8
0
79
13
AUDIO
DISP
SURRAUTO
CH LV.
ADV
STATUS
AUDIO P. VIDEO P.
Z2 Z3 HDZ
LISTENING MODE
HDMI
NET
ALL
Fav
RECEIVER
1
2
4
3
9
10
11
12
5
6
7
8
13
14
17
18
15
16
6
The remote has been conveniently color-coded according to component control using the following system:
!White – Receiver control, TV control
!Blue – Operation of other devices and each input (TUNER, etc.) (See pages 63, 64, 66, 67 and 96.)
1 uSTANDBY/ON
This switches between standby and on for this receiver.
2 ALL ZONE STBY
Use this button to perform unique operations (page 95).
3 MAIN RECEIVER
Switches the remote to control the receiver (used to select the white commands).
Switch to perform operations in the main zone.
4 SOURCE CONTROL buttons
Switches the input. Also, switches remote control operation mode for operating other devices or each input
(TUNER, etc.) (page 93).
The input for HDMI , NET and ALL switches each time these buttons are pressed.
5 TV control buttons
These buttons can be used to perform operations on the TV to which the TV INPUT button is assigned. The TV can
be operated with these buttons regardless of the input set for the remote control’s operation mode (page 93).
6 Receiver Control buttons
!STATUS – Displays the IP address and information such as selected/set functions and input signals on the
display (page 90).
!OUT P. (OUTPUT PARAMETER) – Switches the output terminal of the HDMI signal or speaker terminal to be
played (page 87).
!RETURN – Press to confirm and exit the current menu screen.
!CH LV. (CHANNEL LEVEL) – Press repeatedly to select a channel, then use k/lto adjust the level (pages
88 and 108).
7 Receiver setting buttons
Press MAIN RECEIVER first to access:
!AUDIO P. (AUDIO PARAMETER) – Use to access the Audio options (page 85).
!VIDEO P. (VIDEO PARAMETER) – Use to access the Video options (page 87).
!HOME MENU – Use to access the Home Menu (pages 59, 60, 82, 99 and 106).
8 i/j/k/l/ENTER
Use the arrow buttons when setting up your surround sound system (see page 99) and the Audio or Video
options (page 85 or 87).
9 LISTENING MODE buttons
!AUTO (AUTO SURROUND/ALC/STREAM DIRECT) – Switches between Auto Surround (page 70), Auto
Level Control mode and Stream Direct mode (page 71).
!SURR (STANDARD SURROUND) – Press for Standard decoding and to switch various modes (Dolby, DTS,
etc.) (page 70).
!ADV (ADVANCED SURROUND) – Use to switch between the various surround modes (page 71).
10 Source device operation button
Operates other devices or each input (TUNER, etc.).
11 DIMMER
Dims or brightens the display (page 90).
12 SLEEP
Use to put the receiver in sleep mode and select the amount of time before sleep (page 89).

13
Controls and displays
02
13 uSOURCE
Press to turn on/off the power to the Pioneer device connected to the receiver.
14 Remote control LED
Lights when a command is sent from the remote control.
15 SUB ZONE CONTROL buttons
!Z2 (ZONE 2) – It is not used with this receiver.
!Z3 (ZONE 3) – It is not used with this receiver.
!HDZ (HDZONE) – Holding down this button (for 1.5 seconds) until the remote control LED flashes one time,
the mode changes to HDZONE operation.
16 VOLUME +/–
Use to set the listening volume.
To adjust the main zone sound volume, press MAIN RECEIVER first and then press this button. When in the sub
zone, press the SUB ZONE CONTROL button first and then press this button.
17 MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
To mute the main zone sound volume, press MAIN RECEIVER first and then press this button. When in the sub
zone, press the SUB ZONE CONTROL button first and then press this button.
18 RCU SETUP
Used to set the remote control (page 93).
Remote control (In case of VSX-830)
This section explains how to operate the remote control for the receiver.
1
2
4
3
9
10
11
12
5
5
6
7
8
13
14
15

14
Controls and displays
02
The remote has been conveniently color-coded according to component control using the following system:
!White – Receiver control, TV control
!Blue – Operation of other devices and each input (TUNER, etc.) (See pages 63, 64, 66, 67 and 96.)
1 uSTANDBY/ON
This switches between standby and on for this receiver.
2 SLEEP
Use to put the receiver in sleep mode and select the amount of time before sleep (page 89).
3 MAIN RECEIVER
Switches the remote to control the receiver (used to select the white commands).
4 Input function buttons
Switches the input. Also, switches remote control operation mode for operating other devices or each input
(TUNER, etc.) (page 93).
The input for HDMI , NET and ALL switches each time these buttons are pressed.
5 Receiver Control buttons
!STATUS – Displays the IP address and information such as selected/set functions and input signals on the
display (page 90).
!SP-A/B – Switches the speaker output on/off. No sounds will be made from the speaker when SP OFF is
selected.
!CH LV. (CHANNEL LEVEL) – Press repeatedly to select a channel, then use k/lto adjust the level (pages
88 and 108).
!RETURN – Press to confirm and exit the current menu screen.
6 Receiver setting buttons
Press MAIN RECEIVER first to access:
!AUDIO P. (AUDIO PARAMETER) – Use to access the Audio options (page 85).
!VIDEO P. (VIDEO PARAMETER) – Use to access the Video options (page 87).
!HOME MENU – Use to access the Home Menu (pages 59, 60, 82, 99 and 106).
7 i/j/k/l/ENTER
Use the arrow buttons when setting up your surround sound system (see page 99) and the Audio or Video
options (page 85 or 87).
8 Component control buttons
The main buttons (d, g, etc.) are used to control a component after you have selected it using the input function
buttons.
The BD, DVD, and CD operation using the component control buttons are limited only to Pioneer components.
The controls above these buttons can be accessed after you have selected the corresponding input function but-
ton (BD, DVD and CD). These buttons also function as described below.
Press TUNER first to access:
Use TUNE +/–can be used to find radio frequencies and PRESET +/–can be used to select preset radio stations
(page 66).
9 SHIFT
It is not used with this receiver.
10 uSOURCE
Press to turn on/off the power to the Pioneer device connected to the receiver.
11 DIMMER
Dims or brightens the display (page 90).
12 TV control buttons
Operates a TV. When operating other manufacturer’s TV, setup as follows.
!u– Use to turn on/off the power of the TV.
!INPUT – Use to select the TV input signal.
!CH +/– – Use to select channels.
!VOL +/– – Use to adjust the volume on your TV.
While holding down TV ubutton, press the input function buttons (listed in the table below) for component you
want to control for about five seconds.
This may not operate depending on the TV.
Default setting: Pioneer
TV preset
Input function button TV Brand
MAIN RECEIVER Pioneer
BD Panasonic
HDMI Sharp
ALL Sony
DVD Toshiba
SAT Mitsubishi
MHL Philips/AOC/TPV
iPod Vizio
CD Samsung
BT LG Electric
TUNER Skyworth
TV Hisense
NET TCL
13 MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
To mute the sound volume, press MAIN RECEIVER first and then press this button.
14 VOLUME +/–
Use to set the listening volume.
15 LISTENING MODE buttons
!AUTO (AUTO SURROUND/ALC/STREAM DIRECT) – Switches between Auto Surround (page 70), Auto
Level Control mode and Stream Direct mode (page 71).
!SURR (STANDARD SURROUND) – Press for Standard decoding and to switch various modes (Dolby, DTS,
etc.) (page 70).
!ADV (ADVANCED SURROUND) – Use to switch between the various surround modes (page 71).

15
Controls and displays
02
Display
HDMI
DIGITAL
ANALOG
L C R
SL SR
XL XR
XC
LFE
AUTO
DIGITAL PLUS
AUTO SURROUND
STREAM DIRECT
PROLOGIC  Neo:6
ADV.SURROUND
STANDARD
SP AB SLEEP
DSD PCM
DTS HD ES 96/24
MSTR
S.RTRV SOUND UP MIX
MONO
dB
MULTI-ZONE STEREO TrueHD
TUNED
ALC AT T
USB
TV
DVD
HDMI
DVR BD
CD TUNER
iPod
[ 2 ][ 3 ][ 4 ]
21 3 974 10811 12 13
19 2015 16 17 18
146
FULL BAND
5
6
1 Signal indicators
Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input sig-
nal automatically (page 72).
2 Program format indicators
Light to indicate the channels to which digital signals are being input.
VSX-930 only: With Dolby Atmos content, the light will not be on when the object base signal is being decoded.
!L/R – Left front/Right front channel
!C– Center channel
!SL/SR – Left surround/Right surround channel
!LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input)
!XL/XR – Two channels other than the ones above
!XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag
3 Digital format indicators
Light when a signal encoded in the corresponding format is detected.
!DIGITAL – Lights with Dolby Digital decoding.
!DIGITAL PLUS – Lights with Dolby Digital Plus decoding.
!TrueHD – Lights with Dolby TrueHD decoding.
!DTS – Lights with DTS decoding.
!DTS HD – Lights with DTS-HD decoding.
!96/24 – Lights with DTS 96/24 decoding.
!DSD – Lights during playback of DSD (Direct Stream Digital) signals.
!DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion.
!PCM – Lights during playback of PCM signals.
!MSTR – Lights during playback of DTS-HD Master Audio signals.
4 MULTI-ZONE
Lights when the MULTI-ZONE feature is active (page 89).
5 FULL BAND
VSX-930 only: Lights when the Full Band Phase Control is switched on (page 73).
6 Listening mode indicators
!ALC – Lights when the ALC (Auto level control) mode is selected (page 70).
!AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 70).
!STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 71).
!ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 71).
!STANDARD – Lights when one of the Standard Surround modes is switched on (page 70).
7 (PHASE CONTROL)
Lights when the Phase Control is switched on (page 72).
8 ATT
Lights when the input signal level is lowered to reduce distortion (page 85).
9 SOUND
Lights when the DIALOG E (Dialog Enhancement) or TONE (tone controls) features is selected (page 85).
10 Tuner indicators
!TUNED – Lights when a broadcast is being received.
!STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode.
!MONO – Lights when the mono mode is set using MPX.
11
Lights when the sound is muted.
12 Master volume level
Shows the overall volume level.
“---” indicates the minimum level, and “+12dB” indicates the maximum level.
13 Input function indicators
Light to indicate the input function you have selected.
14 Scroll indicators
Light when there are more selectable items when making the various settings.
15 Speaker indicators
In case of VSX-930: Lights to indicate the current speaker system using OUT P. (page 87).
In case of VSX-830: When the front panel’s SPEAKERS or remote control’s SP-A/B are pressed, the currently
selected speaker terminal indicator lights.
16 SLEEP
Lights when the receiver is in sleep mode (page 89).
17 Matrix decoding format indicators
!PRO LOGIC II (VSX-830 only) – This lights to indicate Pro Logic II decoding (page 70).
!Neo:6 – When one of the Neo:6 modes of the receiver is on, this lights to indicate Neo:6 processing (page
70).
18 S.RTRV
Lights when the Auto Sound Retriever function is active (page 85).
19 Character display
Displays various system information.
20 Remote control mode indicator
VSX-930 only: Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 111)

16
Controls and displays
02
Front panel
VSX-930
1 2 5
33
467 8
10 119 12 13 14 1615
VSX-830
1 2 5
33
67 8
10 119 1213 14
17 18 15
1 uSTANDBY/ON
This switches between standby and on for this receiver.
2 INPUT SELECTOR dial
Use to select an input function.
3 Indicators
!MCACC PRO (VSX-930)/ADVANCED MCACC (VSX-830) – Lights when EQ is set to ON in the
AUDIO PARAMETER menu (page 85).
!FL OFF – Lights when “off” (nothing displayed) is selected with the display’s dimmer adjustment (page 90).
!HDMI – Blinks when connecting an HDMI-equipped component; lights when the component is connected
(page 27).
!WIRELESS – Lights when connected to the network with wireless. The light slowly blinks during WAC
(Wireless Accessary Configuration) mode (page 53).
4 MULTI-ZONE controls
VSX-930 only
If you’ve made MULTI-ZONE connections (page 32) use these controls to control the sub zone from the main
zone (page 89).
5 Character display
See Display on page 15.
6 TUNER controls
!BAND – Switches between AM and FM radio bands (page 66).
!TUNER EDIT – Use with TUNE i/j, PRESET k/land ENTER to memorize and name stations for recall
(page 66).
!TUNE i/j– Find radio frequencies (page 66).
!PRESET k/l– Find preset stations (page 66).
7 Remote sensor
Receives the signals from the remote control (page 10).
8 MASTER VOLUME dial
9 PHONES jack
Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.
10 MCACC SETUP MIC jack
Use to connect the supplied microphone (page 57).
11 SPEAKERS
Use to change the speaker terminal (page 87).
12 Listening mode buttons
!AUTO SURR/ALC/STREAM DIRECT – Switches between Auto Surround (page 70), Auto Level Control and
Stream Direct mode (page 71).
!STANDARD SURROUND – Press for Standard decoding and to switch various modes ( Pro Logic, Neo:6,
Stereo, etc.) (page 70).
!ADVANCED SURROUND – Use to switch between the various surround modes (page 71).
13 STATUS
Displays the IP address and information such as selected/set functions and the input signal on the display (page
90).
14 iPod iPhone DIRECT CONTROL
Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 63).

17
Controls and displays
02
15 iPod/iPhone terminals
Use to connect your Apple iPod/iPhone as an audio source (page 34), or connect a USB device for audio and
photo playback (page 34).
16 HDMI 5 INPUT terminal
VSX-930 only
Use for connection to a compatible HDMI device (Video camera, etc.) (page 35).
17 DIMMER
VSX-830 only
Dims or brightens the display (page 90).
18 ECO
VSX-830 only
Use to switch the eco mode type (page 71).

18
Connecting your equipment......................................................................................................... 19
Rear panel ......................................................................................................................................19
Determining the speakers’ application........................................................................................20
Placing the speakers......................................................................................................................22
Connecting the speakers............................................................................................................... 23
Installing your speaker system..................................................................................................... 23
About the audio connection......................................................................................................... 26
About the video converter ...........................................................................................................26
About HDMI ...................................................................................................................................27
Connecting your TV and playback components .........................................................................27
Connecting a satellite/cable receiver or other set-top box........................................................ 29
Connecting other audio components ..........................................................................................30
Connecting additional amplifiers.................................................................................................31
Connecting AM/FM antennas....................................................................................................... 31
Making MULTI-ZONE connections................................................................................................32
Connecting to the network through LAN interface ................................................................... 34
Connecting an iPod........................................................................................................................34
Connecting a USB device .............................................................................................................. 34
Connecting an MHL-compatible device....................................................................................... 35
Connecting an HDMI-equipped component to the front panel input ...................................... 35
Connecting an IR receiver .............................................................................................................35
Plugging in the receiver ................................................................................................................ 36
Connecting your equipment (In case of VSX-930)

19
Connecting your equipment (In case of VSX-930)
03
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter
explains the kinds of components you can connect to make up your home theater system.
CAUTION
!Before making or changing the connections, switch off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
!When making connections, also keep the power cords of the devices being connected unplugged from the
power outlets.
!Depending on the device being connected (CD, DVD or BD player, etc.), the methods of connection and ter-
minal names may differ from the explanations in this manual. Also refer to the operating instructions of the
respective devices.
Rear panel
For Taiwan
A
1
TOP MIDDLE
SURROUND SURROUND BACK CENTER
5.2.2ch
5.2chSPEAKER B
5.2.2ch
HDZONE / BI-AMP
FRONT
RLRL
RL
RL (Single)
B
OUT
IN
/MHLBD
6
16-
4321
(
OUTPUT 5 V
0.9 A MAX
)
IR
P R
P B
Y
ASSIGNABLE
COMPONENT VIDEO
FM UNBAL
75
AM LOOP
SUBWOOFER
PRE OUT
1
2
DVD
ANALOG 1 (CD)
ASSIGNABLE
L
R
L
R
SAT/CBL
SELECTABLE ARC CONTROL
(DVD)(
SAT/CBL)
7.2ch
HDMI IN
HDMI OUT
MAIN
HDZONE/MAIN
NETWORK
AUDIO OUT
AUDIO IN
(SAT/CBL)
VIDEO
DVD
SAT/
CBL
MONITOR OUT
VIDEO IN
ANTENNA
CONTROL
12
(TV)
(SAT/CBL)
1
1
DIGITAL IN
ASSIGNABLE
OPTICAL
COAXIAL
AC IN
ASSIGNABLE
L
R
FRONT
PRE OUT
ASSIGNABLE
For other regions
A
1
TOP MIDDLE
SURROUND SURROUND BACK CENTER
5.2.2ch
5.2chSPEAKER B
5.2.2ch
HDZONE / BI-AMP
FRONT
RLRL
RL
RL (Single)
B
OUT
IN
/MHLBD
6
16-
4321
(
OUTPUT 5 V
0.9 A MAX
)
IR
P R
P B
Y
ASSIGNABLE
COMPONENT VIDEO
FM UNBAL
75
AM LOOP
SUBWOOFER
PRE OUT
1
2
DVD
ANALOG 1 (CD)
ASSIGNABLE
L
R
L
R
SAT/CBL
SELECTABLE ARC CONTROL
(DVD)(
SAT/CBL)
7.2ch
HDMI IN
HDMI OUT
MAIN
HDZONE/MAIN
NETWORK
AUDIO OUT
AUDIO IN
(SAT/CBL)
VIDEO
DVD
SAT/
CBL
MONITOR OUT
VIDEO IN
ANTENNA
CONTROL
12
(TV)
(SAT/CBL)
1
1
DIGITAL IN
ASSIGNABLE
OPTICAL
COAXIAL
AC IN
ASSIGNABLE
ASSIGNABLE
Note
The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input
Setup menu on page 59 to change the assignments if other connections are used.
Input function Input Terminals
HDMI Audio Component
BD (BD)
DVD IN 1
SAT/CBL IN 2 COAXIAL IN
HDMI 3 IN 3
HDMI 4 IN 4
HDMI 5
(front panel) IN 5
HDMI 6/MHL IN 6
TV OPTICAL
CD ANALOG-1

20
Connecting your equipment (In case of VSX-930)
03
Determining the speakers’ application
This unit permits you to build various surround systems, in accordance with the number of speakers you have.
!Be sure to connect speakers to the front left and right channels (Land R).
!It is also possible to only connect one of the surround back speakers (SB) or neither.
!If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
!When neither the top middle, surround back, or front wide speaker is connected, Dolby Atmos does not play.
Choose one from Plans [A] to [F] below.
Important
!The Speaker System setting must be made if you use any of the connections shown below other than [A] (see
Speaker system setting on page 106).
!The speakers from which sound is output can be switched according to the speaker layout/usage pattern
(sound is not necessarily output from all connected speakers). Use the OUT P. button to switch the speakers
from which sound is output. For details, see Switching the speaker terminals on page 87.
[A] 7.2 channel surround system (Surround back/Top middle) connection
*Default setting
!Speaker System setting: 7.2ch/5.2.2ch
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
A 7.2 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right
top middle speakers (TMdL/TMdR), the left and right surround speakers (SL/SR), the left and right surround back
speakers (SBL/SBR), and the subwoofers (SW 1/SW 2).
It is not possible to produce sound simultaneously from the surround back speakers and the top middle speakers.
This surround system produces a more true-to-life sound from above.
The speakers from which sound is output can be switched using the OUT P. button. For details, see Switching
the speaker terminals on page 87.
Playback of Dolby Atmos requires a connection with surround back speakers or top middle speakers.
[B] Dolby Enabled Speaker system connection
*Default setting
!Speaker System setting: 7.2ch/5.2.2ch
—Speaker Setting: Dolby Sp (Front)
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
—Speaker Setting: Dolby Sp (Surr)
SBR
TMdL TMdR
SBL
SRSL
R
SW2
C
SW1
L
7.2 ch surround system that consists of connected front left/right speakers (L/R), center speaker (C), left/right
surround speakers (SL/SR), left/right surround back speakers (SBL/SBR), subwoofer (SW 1/SW 2), Dolby Enabled
Speaker (TMdL/TMdR). For information on Dolby Enabled Speaker, refer to page 24.
Audio will not be output at the same time from the surround back speaker and a Dolby Enabled Speaker.
This surround system produces a more true-to-life sound from above.
The speakers from which sound is output can be switched using the OUT P. button. For details, see Switching
the speaker terminals on page 87.
Playback of Dolby Atmos requires a connection with surround back speakers or top middle speakers that use
Dolby Enabled Speakers.