Pioneer VSX-D511-K User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2002
DOWN
STATION
TUNER EDIT INPUT ATT FL DIMMERCLASS BAND MPX
STANDARD
ADVANCED
SURROUND
STEREO/
DIRECT
SIGNAL
SELECT
UP
ENTER
INPUT
SELECTOR
MASTER VOLUME
MULTI JOG
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
R
STANDBY
STANDBY / ON
PHONES
TUNING MONITOR
MULTI JOG
MULTIJOG
MIDNIGHT LOUDNESS TONE QUICK SETUP
LISTENING MODE
N∫m-Û.,,
VSX-D511-K
RRV2599
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D511-K
VSX-D511-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
VSX-D511-K MVXJI AC230V
VSX-D511-S MYXJIEW AC220-230V
VSX-D511-K MYXJIEW AC220-230V
VSX-D511-K MYXJIGR AC220-230V
For details, refer to "Important symbols for good services" on the next page.
T-ZZR APR.2002.printed in Japan

VSX-D511-K
2
1234
1234
C
D
F
A
B
E
SAFTY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 – Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test

VSX-D511-K
3
5678
5678
C
D
F
A
B
E
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.

VSX-D511-K
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFTY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. EXPLODED VIEWS AND PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 PACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 EXTERIOR SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 FRONT PANEL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 OVERALL WIRING CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3 D.D & INPUT(1/4) ASSY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 D.D & INPUT(2/4) ASSY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.5 D.D & INPUT(3/4) ASSY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.6 D.D & INPUT(4/4) ASSY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.7 AMP & PRIMARY(1/2), TRANS2 and TRANS3 ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.8 AMP & PRIM.(2/2), REG., HASHIGETA, B TO B and MECH SW ASSYS . . . . . . . . . . . . . . . 26
3.9 VIDEO, 6CH IN and S.VIDEO ASSYS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.10 FRONT, R.ENCODER and POWER SW ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.11 DIGITAL IN, H.P. and KAWA ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.12 FM/AM TUNER MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4. PCB CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1 TRANS1, TRANS2 and TRANS3 ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2 D.D & INPUT ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.3 AMP INPUT, AMP & PRIMARY and MECHA SW ASSYS. . . . . . . . . . . . . . . . . . . . . . . . 42
4.4 FRONT, POWER SW, H.P. and R.ENCODER ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.5 REGULATOR, HASHIGETA and KAWA ASSYS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.6 DIGITAL IN, 6CH IN, VIDEO and BOARRO TO BOARD ASSYS . . . . . . . . . . . . . . . . . . . . 50
4.7 FM/AM TUNER MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5. PCB PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6. ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7. GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.1 DISASSEMBLY and DIAGNOSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.1.1 DISASSEMBLY and PCB LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.1.2 U-COM BLOCKDIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.1.3 PROTECTION CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7.1.4 POWER ON SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
7.1.5 POWER OFF SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.2 PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.2.1 IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.2.2 DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
8. PANEL FACILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

VSX-D511-K
5
5678
5678
C
D
F
A
B
E
1. SPECIFICATIONS
Î
Accessories
Remote control unit
(XXD3039)
AM loop antenna
(ATB7009)
FM wire antenna
(ADH7005)
AA size IEC R6P
Dry cell batteries (x2)
Amplifier Section
Front .................................... 80 W per channel
(DIN 1kHz, THD 1.0 %, 8 Ω)
Front
Continuous Power Output
..................................................... 80 W per channel
(1kHz, THD 1.0 %, 8 Ω)
Center ......................................... 80 W (1kHz, THD 1.0 %, 8 Ω)
Surround .................... 80 W per channel (1kHz, THD 1.0 %, 8 Ω)
Above specifications are applicable when the power supply is 230V.
Input (Sensitivity/Impedance)
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT ... 200 mV/47 kΩ
Frequency Response
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,TV/SAT
.................................................................. 5 Hz to 100,000 Hz dB
Output (Level/Impedance)
VCR/DVR REC, CD-R/TAPE/MD REC .................... 200 mV/2.2 kΩ
Tone Control
BASS ...................................................................... ±6 dB (100 Hz)
TREBLE .................................................................. ±6 dB (10 kHz)
LOUDNESS ..................................... +9 dB/+9 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio [DIN (Continuous rated power output/50 mW)]
CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT ............. 88/64 dB
Video Section
Input (Sensitivity/Impedance)
VCR/DVR, DVD/LD, TV/SAT ......................................... 1 Vp-p/75 Ω
Output (Level/Impedance)
VCR/DVR ...................................................................... 1 Vp-p/75 Ω
Frequency Response
VCR/DVR, DVD/LD,TV/SAT ]MONITOR ........ 5 Hz to 7 MHz dB
Signal-to-Noise Ratio .............................................................. 55 dB
Cross Talk ............................................................................... 55 dB
FM Tuner Section
Frequency Range .......................................... 87.5 MHz to 108 MHz
Usable Sensitivity ....................... Mono:13.2 dBf, IHF (1.3 µV/ 75 Ω)
50 dB Quieting Sensitivity ......................................... Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio ................................. Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Signal-to-Noise Ratio (DIN) ....................................... Mono: 62 dB
Stereo: 58 dB
Distortion ........................................................Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity ................................. 60 dB (400 kHz)
Stereo Separation ...................................................... 40 dB (1 kHz)
Frequency Response ................................. 30 Hz to 15 kHz (±1 dB)
Antenna Input (DIN) .............................................. 75 Ωunbalanced
AM Tuner Section
Frequency Range ........................................... 531 kHz to 1,602 kHz
Sensitivity (IHF, Loop antenna) ......................................... 350 µV/m
Selectivity ................................................................................ 25 dB
Signal-to-Noise Ratio .............................................................. 50 dB
Antenna ...................................................................... Loop antenna
Miscellaneous
Power Requirements
UK model
European model
...............................................
.........................................
A
AC 220-230 V, 50/60 Hz
C 230 V, 50/60Hz
Power Consumption
....................................................................... 220W
In Standby ............................................................................. 1 W
Dimensions ................................... 420 (W) x 158 (H) x 393 (D) mm
Weight (without package)
kg.......................................................................... 9.0
Furnished Parts
AM loop antenna ............................................................................ 1
FM wire antenna ............................................................................ 1
Dry cell batteries (AA size IEC R6P).............................................. 2
Remote control ............................................................................... 1
Operating instructions .................................................................... 1
Specifications and the design are subject to possible modifications
without notice, due to improvements.
+0
–3
+0
–3
"DTS" ,“ES”and "DTS Digital Surround" are trademarks
of Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic II”and the double D symbol 2are
trademarks of Dolby Laboratorories.
Continuous Power Output (STEREO mode)
INPUT SELECTOR
CDTV/SATDVD/LD
RECEIVER
DVD
DVD CONTROL
SUB TITLE
AUDIO TEST
TONE LEVEL EFFECT
MENU
DVD
TUNER
EDIT
RECEI- VER
TOP MENU
STANDARD STEREO
ADVANCED
SURROUND
INPUT
ATT FL
DIMMER MUTE
MASTER
VOLUME
CD-R/
TAPE/MD VCR/
DVR
ENTER
SETUP
AV RECEIVER
TUNING
BAND CLASS MPX
DISPLAY
CH SELECT
STATION
MIDNIGHT/
LOUDNESS
TUNER
1
¢4
¡
78
3

VSX-D511-K
6
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
1
3
2
49
11
12
7
10
13
14
5
6
/MYXJIEW Type
8

VSX-D511-K
7
5678
5678
C
D
F
A
B
E
PACKING parts List
(2) CONTRAST TABLE
VSX-D511-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D511-S/MYXJIEW are constructed the same except for the
following :
Mark No. Description Part No.
1 FM wire antenna ADH7005
NSP 2 Warranty Card ARY7022
3 AM loop antenna ATB7009
NSP 4 Dry cell batteries (AA/R6P) VEM-013
5 Operating instructions XRE3057
(English/German)
6 Operating instructions See Contrast table(2)
7 Remote Control Unit XXD3039
8 Battery Cover AZA7378
NSP 9 Polyethylene Bag Z21-038
10 Packing Sheet AHG7069
11 Left Pad R5 XHA3032
12 Right Pad R5 XHA3033
13 Packing Case See Contrast table(2)
14 Operating instructions See Contrast table(2)
Mark No. Description Part No.
Mark NO Symbol and Description VSX-D511-K/
MVXJI
VSX-D511-S/
MYXJIEW
VSX-D511-K/
MYXJIEW
VSX-D511-K/
MYXJIGR
6 Operating Instructions (French,Italian) Not used XRC3056 XRC3056 Not used
13 Packing Case XHD3204 XHD3205 XHD3204 XHD3204
14 Operating Instructions (Spanish,Dutch) Not used XRC3070 XRC3070 Not used

VSX-D511-K
8
1234
1234
C
D
F
A
B
E
2.2 EXTERIOR SECTION
D
L
K
H
M
J
I
CI
J
M
L
K
H
E
A
B
C
D
E
N
N
F
F
A
B
G
G
53
24
40
23
53
53
57
53
53
53
53
53
53
53
53
53
53
53
53
53
44
28
18
1
15
56
3
43
39(1/2)
39(2/2)
45
6
53
41
57
25
26
27
29 53
53
53
34
10
7
53
30
2
4
17 16
5
53
22
53
53
54
54 50
50
53
20
Accessory of
Front Panel
53
51
53
53
53
Refer to
"2.3 FRONT PANEL SECTION".
55
55
48
47
49
46
9
31
53
37
53
H
A
L
N
J
8M
B
E
F
13 K
X
D
C
I
G
53
38
53
53
22
21
NON-CONTACT
SIDE CONTACT
SIDE
53 38
42
42
35

VSX-D511-K
9
5678
5678
C
D
F
A
B
E
EXTERIOR SECTION parts List
(2) CONTRAST TABLE
VSX-D511-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D511-S/MYXJIEW are constructed the same except for the
following :
Mark No. Description Part No.
1 D.D & INPUT ASSY XWX3044
2 AMP ASSY XWZ3533
3 REGULATOR ASSY XWZ3544
4 AMP INPUT ASSY XWZ3547
5 TRANS2 ASSY XWZ3555
6 HASHIGETA ASSY XWZ3566
7 BOARD TO BOARD ASSY XWZ3527
8 6CH IN ASSY XWZ3507
9 DIGITAL IN ASSY XWZ3518
10 S. VIDEO ASSY XWZ3521
11 •••••
12 •••••
13 KAWA ASSY XWZ3529
14 •••••
15 VIDEO ASSY XWZ3490
NSP 16 TRANS1 ASSY XWZ3552
NSP 17 TRANS3 ASSY XWZ3560
18 FM/AM TUNER MODULE AXQ7232
19 •••••
> 20 Power Transformer (T1) ATS7259
21 •••••
> 22 Fuse (FU1:T2.5A) REK1026
> 23 Power Cord See Contrasttable(2)
24 Cord Stopper CM-22B
25 28P F•F•C/30V (J31) XDD3097
DD CN102 - FRONT CN402
26 17P F•F•C/30V (J32) XDD3098
KAWA CN5001 - FRONT CN401
27 7P F•F•C/30V (J33) XDD3099
KAWA CN5004 - VIDEO CN503
28 13P F•F•C/30V (J34) XDD3100
KAWA CN5005 - FM/AM TUNER CN201
29 19P F•F•C/30V (J35) XDD3101
DD CN106 - AMP INPUT CN254
30 23P F•F•C/30V (J36) XDD3102
AMP CN53 - REGULATOR CN801
31 7P F•F•C/30V (J37) XDD3103
DD CN9101 - DIGITAL IN CN1901
32 •••••
33 •••••
34 9P F•F•C/30V (J48) XDD3106
DD CN104 - 6CH IN CN307
35 Top Cover See Contrast table(2)
36 •••••
NSP 37 Under Base 409 ANA7094
38 Insulator PNW2766
39 FFC Cover R5 XMR3047
40 Rear Panel XNC3143
41 Bonnet D510 See Contrast table(2)
42 Push Rivet See Contrast table(2)
43 Tuner Shield R5 XNG3072
44 PCB Angle R5 XNG3073
45 Reg Support R5 XNG3074
NSP 46 Heat Sink Assy 0.8 ANH7118
47 Heat Sink Angle F ANG7251
48 Heat Sink Angle R ANG7252
NSP 49 Heat Sink 0.8 ANH7110
50 Screw 3x23 ABA7043
51 PCB Mold AMR2533
52 Screw See Contrast table(2)
53 Screw BBZ30P080FMC
54 Screw BBZ30P200FMC
55 Screw FBT40P080FZK
56 Tuner Sheet XEC3031
57 Screw See Contrast table(2)
Mark No. Description Part No.
Mark NO Symbol and Description VSX-D511-K/
MVXJI
VSX-D511-S/
MYXJIEW
VSX-D511-K/
MYXJIEW
VSX-D511-K/
MYXJIGR
> 23 AC Power Cord VDG1076 VDG1077 VDG1077 VDG1077
35 Top Cover XME3004 XME3006 XME3004 XME3004
41 Bonnet XZN3111 XZN3122 XZN3111 XZN3111
42 Push Rivet AEC7025 XEC3026 AEC7025 AEC7025
57
Screw
FBT40P080FZK FBT40P080FNI FBT40P080FZK FBT40P080FZK

VSX-D511-K
10
1234
1234
C
D
F
A
B
E
2.3 FRONT PANEL SECTION
18
9
15
10
13
2
12
11
7
14
6
1
3
16
16
17
16
16
16
16
16
16
16
16
16
16
4
8
20
Q
UO
P
16 16
Y
5
19

VSX-D511-K
11
5678
5678
C
D
F
A
B
E
FRONT PANEL SECTION parts List
(2) CONTRAST TABLE
VSX-D511-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D511-S/MYXJIEW are constructed the same except for the
following :
Mark No. Description Part No.
1 FRONT ASSY XWZ3493
2 POWER SW ASSY XWZ3510
3 H.P. ASSY XWZ3513
4 R. ENCODER ASSY XWZ3511
5 MECH SW ASSY XWZ3514
6 Front Panel See Contrast table(2)
7 Sub Button See Contrast table(2)
8 Earth Plate R5 HP XNG3066
9 Pioneer Badge See Contrast table(2)
10 Led Lens 1.6 XAK3308
11 Select Knob See Contrast table(2)
12 Volume Knob See Contrast table(2)
13 Power Button See Contrast table(2)
14 Sub Panel See Contrast table(2)
15 Jog Button See Contrast table(2)
16 Screw PPZ30P080FMC
17 Screw BBZ30P080FMC
18 D Panel R5 W XAK3320
19 Power Button M See Contrast table(2)
20 C Ring DIA8.1 XBH3016
Mark No. Description Part No.
Mark NO Symbol and Description VSX-D511-K/
MVXJI
VSX-D511-S/
MYXJIEW
VSX-D511-K/
MYXJIEW
VSX-D511-K/
MYXJIGR
6 Front Panel XMB3065 XMB3076 XMB3065 XMB3065
7 Sub Button XAD3125 XAD3133 XAD3125 XAD3125
9 Pioneer Badge XAM3006 VAM1129 XAM3006 XAM3006
11 Select Knob XAB3023 XAB3024 XAB3023 XAB3023
12 Volume Knob XAB3025 XAB3026 XAB3025 XAB3025
13 Power Button XAD3123 XAD3129 XAD3123 XAD3123
14 Sub Panel XAK3273 XAK3299 XAK3273 XAK3273
15 Jog Button XAD3124 XAD3131 XAD3124 XAD3124
19 Power Button M XAD3127 XAD3137 XAD3127 XAD3127

VSX-D511-K
12
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
1
1
3
1
AXQ7232
CN101
10
CN201
7
CN307
IC101
TC9273F-007
(FUNCTION SEL)
IC303
IC1901
IC302
IC302
IC104
IC102
NJU7312AM
IC9701
IC9101
IC9508
IC9504
IC9503
IC9502
(ADC)
(DIR)
(DAC) (FL/FR)
(EXP/DSP)
(SL/SR)
(C)
(SW)
(CODEC)
(for DECODE)
(SP
config)
IC9501
BS62LV
1024TC-70
(RAM for
AAC)
PDN030A
(ROM for
DECODE)
TC74
VHC574F
TC74
VHC574F
CRYSTAL
DSP
A
M
J
3
1
7
15
9
CN104
7
5
1
CN1901
6
CN9101
2
3
5
3
2
5
15
4
3
2
123
32
43
39-40
11-13
10 22
30
27
28
26 21
IC9702
21
IC9703
31
IC9703
57
IC9704
21
IC9201
31
IC9705
21
AK4586 NJM4558MD
(LPF)
NJM4558MD
(6dB AMP)
NJM2100M
IC9601
NJU7313
AM
4
6
3
8
7
20
21
19
12
11
10
9
5
1
7
5
9
10 11
N
9
5
7
3
9
5
7
311
11
IC351
IC352 (Y SEL)
(C SEL)
8
X
CN107
1
K
(8 16bit)
6CH IN ASSY
DIGITAL IN ASSY
D.D & INPUT ASSY
S. VIDEO
ASSY
1
5
CN1902
13
1

VSX-D511-K
13
5678
5678
C
D
F
A
B
E
14.1/24.1 14.7/27.3 13.8
IC103
IC105
IC106
IC107
IC107
Q112 Q303
Q603
Q601
Q1552
Q653
Q651
Q632
Q631
uPC2570
(PRE AMP)
L
E
CN101
14
CN302
1
11
15
17
31
34
33
36
6
9
57
57
31
57
IC601
24
26
IC602
24 26
IC601 RY751
RY753
RY752
22 15
U
B
H
CN702 6
CN1551
6
CN106
4CN601
9
85
111
+12V
-12V
T1
POWER
TRANSFORMER
T51
AC IN
D801–D804
U+5V
D51-D54
RY51
IC51
IC801
T+12V IC805
CN101 IC802
NECK+B
POWER AMP
IC601, IC602
NECK-B
D702
D701
+BVL
+BVH
-BVH
-BVL
FL AC
FL AC
Q701
Q702
B
Y
B
A
D+5V D721–D724
IC803
A+5V IC804
CN101
E
A
CN101
A
CN402
O
IC301
(CONPONENT SEL)
L
9
5
7
1
11
3
6
VIDEO ASSY
MECHA SW
ASSY
AMP & PRIMARY ASSY
AMP INPUT ASSY

VSX-D511-K
14
1234
1234
C
D
F
A
B
E
3.2 OVERALL WIRING CONNECTION DIAGRAM
FRONT ASSY
(XWZ3493)
O
BOARD TO
BOARD
ASSY
(XWZ3527)
S. VIDEO
ASSY
(XWZ3521) N
G
R.ENCODER
ASSY
(XWZ3511) P
D.D &
INPUT
ASSY
(XWX3044)
A
REGULATOR
ASSY
(XWZ3544)
E
6CH IN ASSY
(XWZ3507)
M
VIDEO
ASSY
(XWZ3490)
FM/AM TUNER
MODULE
(AXQ7232)
L
X
HASHIGETA
ASSY
(XWZ3566)
F
AMP INPUT ASSY
(XWZ3547)
H
KAWA
ASSY
(XWZ3529) K
A1/4,
A2/4,
A3/4,
A4/4

VSX-D511-K
15
5678
5678
C
D
F
A
B
E
FU1 : REK1026(T2.5A/250V)
(ATS7259)
VDG1076 : /MVXJI
VDG1077 : /MYXJI
MECHA SW ASSY
(XWZ3514)
DIGITAL IN
ASSY
(XWZ3518)
J
POWER SW ASSY
(XWZ3510)
Q
Y
U
H.P. ASSY
(XWZ3513)
TRANS3
ASSY
(XWZ3560)
D
TRANS2
ASSY
(XWZ3555)
TRANS1
ASSY
(XWZ3552)
CI
AMP&
PRIMARY
ASSY
(XWZ3533)
B
J3(J8)
J7J6
J1J2
J4
J5
B1/2,
B2/2
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".

VSX-D511-K
16
1234
1234
C
D
F
A
B
E
3.3 D.D & INPUT(1/4) ASSY
A
D.D & INPUT ASSY
(XWX3044)
A 1/4
A 1/4
A2/4
CN802
E

VSX-D511-K
17
5678
5678
C
D
F
A
B
E
A 1/4
CN402
O
A2/4
A4/4
A4/4
A2/4,4/4
A4/4 A2/4,3/4,4/4
A2/4 A2/4 A3/4
CN1002
F
CN307
M: The power supply is shown with the marked box.
,

VSX-D511-K
18
1234
1234
C
D
F
A
B
E
3.4 D.D & INPUT(2/4) ASSY
A
D.D & INPUT ASSY
(XWX3044)
A 2/4
A 2/4
A1/4
A4/4
A1/4
A1/4
A3/4
CN1901
J
A3/4
A1/4

VSX-D511-K
19
5678
5678
C
D
F
A
B
E
A 2/4
CN254
H
A1/4
A1/4
A1/4 A1/4
A1/4

VSX-D511-K
20
1234
1234
C
D
F
A
B
E
3.5 D.D & INPUT(3/4) ASSY
A
A 3/4
A1/4