Pioneer VSX-D711-K User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2002
Model Type Power Requirement Remarks
VSX-D711-K MVXJI AC230V
VSX-D711-K MYXJIEW AC220-230V
VSX-D711-K MYXJIGR AC220-230V
VSX-D711-S MYXJIEW AC220-230V
RRV2607
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D711-K
T – ZZV APR. 2002 Printed in Japan
VSX-D711-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
For details, refer to "Important symbols for good services" on page 3.
DOWN UP
ENTER
INPUT
SELECTOR
MASTER VOLUME
MULTI JOG
R
STANDBY
STANDBY / ON
PHONES
N∫m-Û˘,,∫
OFF ON

VSX-D711-K,VSX-D711-S
2
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 –Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test

VSX-D711-K,VSX-D711-S
3
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.

VSX-D711-K,VSX-D711-S
4
SAFETY INFORMATION ................................................................... 2
1. SPECIFICATIONS ......................................................................... 5
2. EXPLODED VIEWS AND PARTS LIST......................................... 6
2.1 PACKING................................................................................ 6
2.2 EXTERIOR ............................................................................. 8
2.3 FRONT PANEL..................................................................... 10
3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM .......................... 12
3.1 BLOCK DIAGRAM................................................................ 12
3.2 OVERALL WIRING CONNECTION DIAGRAM ................... 14
3.3 DD & INPUT ASSY(1/4) ....................................................... 16
3.4 DD & INPUT ASSY(2/4) ....................................................... 18
3.5 DD & INPUT ASSY(3/4) ....................................................... 20
3.6 DD & INPUT ASSY(4/4) ....................................................... 22
3.7 AMP & PRIMARY(1/2), TRANS2 and TRANS3 ASSYS............. 24
3.8 AMP & PRIMARY(2/2), REGULATOR, HASHIGETA
B TO B , AMP INPUT and TRANS 1 ASSYS................ 26
3.9 DIGITAL IN ASSY................................................................. 28
3.10 KAWA ASSY....................................................................... 29
3.11 VIDEO and 6CH IN ASSYS................................................ 30
3.12 S. VIDEO ASSY.................................................................. 31
3.13 FRONT, R. ENCODER and POWER SW ASSYS ............. 32
3.14 FRONT VIDEO and H.P. ASSYS ....................................... 34
3.15 TRANS4 and MECHA SW ASSYS..................................... 35
3.16 FM/AM TUNER MODULE .................................................. 36
4. PCB CONNECTION DIAGRAM................................................... 38
4.1 TRANS1, TRANS2, TRANS3 and TRANS4 ASSYS............ 39
4.2 DD & INPUT ASSY............................................................... 40
4.3 AMP & PRIMARY, AMP INPUT and MECHA SW ASSYS ......... 44
4.4 REGULATOR, HASHIGETA and KAWA ASSYS................. 46
4.5 B TO B, DIGITAL IN, VIDEO and 6CH IN ASSYS...................... 48
4.6 S. VIDEO and FRONT VIDEO ASSYS ....................................... 50
4.7 FRONT, POWER SW, H.P. and R. ENCODER ASSYS............. 52
4.8 FM/AM TUNER MODULE ........................................................... 56
5. PCB PARTS LIST ........................................................................ 57
6. ADJUSTMENT ............................................................................. 63
7. GENERAL INFORMATION ......................................................... 64
7.1 DIAGNOSIS.......................................................................... 64
7.1.1 U-COM BLOCKDIAGRAM .................................................... 64
7.1.2 POWER ON AND OFF SEQUENCE .................................... 65
7.1.3 PROTECTION CIRCUIT ....................................................... 67
7.2.2 PCB LOCATION ................................................................... 68
7.2 PARTS .................................................................................. 69
7.2.1 IC ........................................................................................... 69
7.2.2 DISPLAY ............................................................................... 77
7.3 CLEANING ........................................................................... 78
8. PANEL FACILITIES..................................................................... 79
CONTENTS

5
VSX-D711-K, VSX-D711-S
Accessories
Remote control unit
(XXD3042)
AM loop antenna
(ATB7009) FM wire antenna (ADH7005) AA size IEC R6P Dry cell batteries (x2)
Miscellaneous
Power Requirements
UK model .......................................................... AC 230 V, 50/60 Hz
European model......................................... AC 220-230V, 50/60 Hz
Power Consumption
VSX-D711 ..........................................................................250W
In Standby ............................................................................. 1 W
Dimensions ................................... 420 (W) x 158 (H) x 401 (D) mm
.........................................................10 kg
Furnished Parts
AM loop antenna ............................................................................ 1
FM wire antenna ............................................................................ 1
Dry cell batteries (AA size IEC R6P).............................................. 2
Remote control............................................................................... 1
Operating instructions .................................................................... 1
Specifications and the design are subject to possible modifications
without notice, due to improvements.
"DTS" ,"DTS-ES Extended Surround" and "Neo:6" are
trademarks of Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double D symbol are
trademarks of Dolby Laboratorories.
Amplifier Section
Continuous Power Output (STEREO mode)
Front ..................... 100 W per channel (DIN 1kHz,THD 1.0 %, 8 Ω)
Continuous Power Output
Front ............................ 100 W per channel (1kHz, THD 1.0 %, 8 Ω)
Center ............................................. 100 W (1kHz,THD 1.0 %, 8 Ω)
Surround ..................... 100 W per channel (1kHz, THD 1.0 %, 8 Ω)
•Above specifications are applicable when the power supply is
230V.
Input (Sensitivity/Impedance)
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT ... 200 mV/47 kΩ
Frequency Response
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,
TV/SAT ...................................................... 5 Hz to 100,000 Hz dB
Output (Level/Impedance)
VCR/DVR REC, CD-R/TAPE/MD REC .................... 200 mV/2.2 kΩ
Tone Control
BASS ...................................................................... ±6 dB (100 Hz)
TREBLE .................................................................. ±6 dB (10 kHz)
LOUDNESS .................................... +9 dB/+9 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio [DIN (Continuous rated power output/50 mW)]
CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT .................. 96 dB
Video Section
Input (Sensitivity/Impedance)
VCR/DVR, DVD/LD, TV/SAT ......................................... 1 Vp-p/75 Ω
Output (Level/Impedance)
VCR/DVR ...................................................................... 1 Vp-p/75 Ω
Frequency Response
VCR/DVR, DVD/LD,TV/SAT ]MONITOR........ 5 Hz to 7 MHz dB
Signal-to-Noise Ratio ..............................................................55 dB
FM Tuner Section
Frequency Range.......................................... 87.5 MHz to 108 MHz
Usable Sensitivity......................Mono:13.2 dBf, IHF (1.3 µV/ 75 Ω)
50 dB Quieting Sensitivity ......................................... Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio ................................ Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Signal-to-Noise Ratio (DIN) ......................................... Mono: 62 dB
Stereo: 58 dB
Distortion........................................................ Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity ................................. 60 dB (400 kHz)
Stereo Separation ...................................................... 40 dB (1 kHz)
Frequency Response .................................30 Hz to 15 kHz (±1 dB)
Antenna Input (DIN) ..............................................75 Ωunbalanced
AM Tuner Section
Frequency Range...........................................531 kHz to 1,602 kHz
Sensitivity (IHF, Loop antenna) .........................................350 µV/m
Selectivity ................................................................................25 dB
Signal-to-Noise Ratio ..............................................................50 dB
Antenna...................................................................... Loop antenna
+0
–3
+0
–3
Weight (without package)
1. SPECIFICATIONS

6
VSX-D711-K, VSX-D711-S
2. EXPLODEDVIEWS AND PARTS LIST
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
1
3
2
410
12
13
8
11
14
5
6
7
MYXJIEW Type Only
9
2.1 PACKING

7
VSX-D711-K, VSX-D711-S
1 FM Wire Antenna ADH7005
NSP 2 Warranty Card ARY7022
3 AM Loop Antenna ATB7009
NSP 4 Dry Cell Batteries(AA/R6P) VEM-013
5 Operating Instructions XRE3059
(English/German)
6 Operating Instructions See Contrast table (2)
(French/Italian)
7 Operating Instructions See Contrast table (2)
(Dutch/Spanish)
8 Remote Control XXD3042
9 Battery Cover XZA3002
NSP 10 Polyethylene Bag Z21-038
11 Packing Sheet AHG7069
12 Left Pad R5 XHA3032
13 Right Pad R5 XHA3033
14 Packing Case See Contrast table (2)
(1) PACKING PARTS LIST
Mark No. Description Part No.
Mark
6 Operating Instructions(French/Italian) Not used XRC3060 Not used XRC3060
7 Operating Instructions(Dutch/Spanish) Not used XRC3071 Not used XRC3071
14 Packing Case XHD3206 XHD3206 XHD3206 XHD3294
Remarks
Part No.
VSX-D711-K VSX-D711-K VSX-D711-K VSX-D711-S
/MVXJI /MYXJIEW /MYXJIGR /MYXJIEW
Symbol and Description
No.
(2) CONTRAST TABLE
VSX-D711-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D711-S/MYXJIEW are constructed the same except for
the following:

8
VSX-D711-K, VSX-D711-S
53
58
53
53
53
36
57 42
53 38
O
O
35
12
T
52
D
L
K
H
M
J
I
CI
J
M
L
K
H
E
A
B
C
D
E
N
N
F
F
A
B
G
G
53
24
40
53
53
56
53
53
53
53
53
53
53
53
53
53
53
53
53
44
28
18
1
15
3
43
39(1/2)
39(2/2)
45
6
53
41
56
25
26
27
29
53
53
34
10
7
53
30
2
4
17 16
5
53
20
53
53
54
54 50
50 53
19
Accessory of
Front Panel
53
51
53
53
53
Refer to
"2.3 FRONT PANEL SECTION".
55
55
48
47
49
46
9
31
53
37
53
H
A
L
N
J
8M
B
E
F
13 K
V
D
C
I
G
53
38
53
53
NON-CONTACT
SIDE CONTACT
SIDE
23
60
VSX-D711-S
/MYXJIEW Only
59
2.2 EXTERIOR

9
VSX-D711-K, VSX-D711-S
(1) EXTERIOR PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 D.D & INPUT ASSY XWX3047
2 AMP&PRIMARY ASSY XWZ3537
3 REGULATOR ASSY XWZ3545
4 AMP INPUT ASSY XWZ3550
5 TRANS2 ASSY XWZ3558
6 HASHIGETA ASSY XWZ3567
7 BOARD TO BOARD ASSY XWZ3575
8 6CH IN ASSY XWZ3507
9 DIGITAL IN ASSY XWZ3518
10 S. VIDEO ASSY XWZ3522
11 •••••
12 TRANS4 ASSY XWZ3526
13 KAWA ASSY XWZ3529
14 •••••
15 VIDEO ASSY XWZ3584
NSP 16 TRANS1 ASSY XWZ3553
NSP 17 TRANS3 ASSY XWZ3561
18 FM/AM TUNER MODULE AXQ7232
19 Power Transformer (T1) XTS3046
20 FU1(T2.5A) REK1026
21 •••••
22 •••••
23 AC Power Cord See Contrast table (2)
24 Cord Stopper CM-22B
25 28P F•F•C/30V (J31) XDD3097
(DD&INPUT CN102
–FRONT CN402)
26 17P F•F•C/30V (J32) XDD3098
(KAWA CN5001
–FRONT CN401)
27 7P F•F•C/30V (J33) XDD3099
(KAWA CN5004
–VIDEO CN503)
28 13P F•F•C/30V (J34) XDD3100
(KAWA CN5005
–FM/AM TUNER CN201)
29 19P F•F•C/30V (J35) XDD3101
(DD&INPUT CN106
–AMP INPUT CN254)
30 23P F•F•C/30V (J36) XDD3102
(AMP&PRIMARY CN53
–REGULATOR CN801)
31 7P F•F•C/30V (J37) XDD3103
(DD&INPUT CN9101
–DIGITAL IN CN1901)
32 •••••
33 •••••
34 9P F•F•C/30V (J48) XDD3106
(DD&INPUT CN104
–6CH IN CN307)
35 3P F•F•C/30V (J22) XDD3107
(AMP INPUT CN251
–TRANS4 CN891)
36 Fan Motor XXM3002
NSP 37 Under Base 409 ANA7094
38 Insulator PNW2766
39 FFC Cover R5 XMR3047
40 Rear Panel 711/MY XNC3144
41 Bonnet D510 See Contrast table (2)
42 Fan Holder R4 XNG3040
43 Tuner Shield R5 XNG3072
44 PCB Angle R5 XNG3073
45 Reg Support R5 XNG3074
NSP 46 Heat Sink Assy 0.4*40 XNH3023
47 Heat Sink Angle F ANG7251
48 Heat Sink Angle R ANG7252
49 Heat Sink XNH3022
50 Screw 3x23 ABA7043
51 PCB Mold AMR2533
NSP 52 Fuse Card AAX7277
53 Screw BBZ30P080FMC
54 Screw BBZ30P200FMC
55 Screw FBT40P080FZK
56 Screw See Contrast table (2)
NSP 57 Binder Assy XWZ3571
NSP 58 Holder Assy XWZ3574
59 Tuner Sheet MY XEC3031
NSP 60 N Label 711S/MY See Contrast table (2)
Mark
23 AC Power Code VDG1076 VDG1077 VDG1077 VDG1077
41 Bonnet D510 XZN3112 XZN3112 XZN3112 XZN3122
56 Screw (for Bonnet) FBT40P080FZK FBT40P080FZK FBT40P080FZK FBT40P080FNI
NSP 60 N Label 711S/MY Not used Not used Not used XAL3112
Remarks
Part No.
VSX-D711-K VSX-D711-K VSX-D711-K VSX-D711-S
/MVXJI /MYXJIEW /MYXJIGR /MYXJIEW
Symbol and Description
No.
(2) CONTRAST TABLE
VSX-D711-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D711-S/MYXJIEW are constructed the same except for
the following:

10
VSX-D711-K, VSX-D711-S
18
21
15
2013 2
12
11
36
19
23
4
23
24
1
6
28
34
34
35
34
22 16
25
29
34 34
34
34
34
34
34
34
34
34 33
33
30
33
3
27
8
10
26
32
31
Q
SO
P
R
U
34
14 7
34
36
2.3 FRONT PANEL

11
VSX-D711-K, VSX-D711-S
(1) FRONT PANEL PARTS LIST
Mark No. Description Part No.
1 FRONT ASSY XWZ3498
2 POWER SW ASSY XWZ3510
3 H.P. ASSY XWZ3513
4 FRONT VIDEO ASSY XWZ3515
5•••••
6 R. ENCODER ASSY XWZ3511
7 MECHA SW ASSY XWZ3514
NSP 8 8P Shielded Cable (J29) XDX3012
9•••••
10 Damper Assy AXA7052
11 Select Knob R5 See Contrast table (2)
12 Volume Knob R5 See Contrast table (2)
13 Power Button R5 See Contrast table (2)
14 Power Button R5M See Contrast table (2)
15 Jog Button R5 See Contrast table (2)
16 Door Button R5 See Contrast table (2)
17 •••••
18 D Panel R5 W/MY XAK3320
19 BN Cover 711/MY See Contrast table (2)
20 LED Lens 1.6 XAK3308
Mark
11 Select Knob R5 XAB3023 XAB3023 XAB3023 XAB3024
12 Volume Knob R5 XAB3025 XAB3025 XAB3025 XAB3026
13 Power Button R5 XAD3123 XAD3123 XAD3123 XAD3129
14 Power Button R5M XAD3127 XAD3127 XAD3127 XAD3137
15 Jog Button R5 XAD3124 XAD3124 XAD3124 XAD3131
16 Door Button R5 XAD3126 XAD3126 XAD3126 XAD3135
19 BN Cover 711/MY XAK3291 XAK3291 XAK3291 XAK3284
21 Pioneer Badge XAM3006 XAM3006 XAM3006 VAM1129
23 Cushion R4B XED3001 XED3001 XED3001 Not used
23 Cushion R5S Not used Not used Not used XED3003
24 Front Panel 711 XMB3066 XMB3066 XMB3066 XMB3071
30 Door Assy R5 XXG3091 XXG3091 XXG3091 XXG3093
NSP 31 Door R5 XAK3275 XAK3275 XAK3275 XAK3281
NSP 32 Door Cover R5 XAK3276 XAK3276 XAK3276 XAK3283
NSP 33 Screw 2x35 XBA3007 XBA3007 XBA3007 XBA3008
Remarks
Part No.
VSX-D711-K VSX-D711-K VSX-D711-K VSX-D711-S
/MVXJI /MYXJIEW /MYXJIGR /MYXJIEW
Symbol and Description
No.
(2) CONTRAST TABLE
VSX-D711-K/MVXJI, /MYXJIEW, /MYXJIGR and VSX-D711-S/MYXJIEW are constructed the same except for
the following:
Mark No. Description Part No.
21 Pioneer Badge See Contrast table (2)
22 Screw DR 3x8W XBA3010
23 Cushion R4 See Contrast table (2)
24 Front Panel 711 See Contrast table (2)
25 Magnet R5 XMF3002
26 Holder L R5 XMR3046
27 Earth Plate R5 HP XNG3066
28 Earth Plate R5 D XNG3067
29 Magnet Cover R5 XNG3075
30 Door Assy R5 See Contrast table (2)
NSP 31 Door R5 See Contrast table (2)
NSP 32 Door Cover R5 See Contrast table (2)
NSP 33 Screw 2x35 See Contrast table (2)
34 Screw PPZ30P080FMC
35 Screw BBZ30P080FMC
NSP 36 C Ring DIM8.1 XBH3016

VSX-D711-K,VSX-D711-S
12
1
1
3
1
FRONT
AXQ7232
CN101
10
CN201
7
CN307
IC101
TC9273F-007
(FUNCTION SEL)
IC303
IC1901
IC302
IC302
IC104
IC102
IC9701
IC9101
IC9508
IC9504
IC9503
IC9502
(ADC)
(DIR)
(DAC) (FL/FR)
(EXP/DSP)
NJU7312AM
(SL/SR)
(C)
(SW)
(CODEC)
(for DECODE)
(SP
config)
IC9501
CS493292
BS62LV
1024TC-70
(RAM for
AAC)
PDN030A
(ROM for
DECODE)
TC74
VHC574F
TC74
VHC574F
CRYSTAL
DSP
A
M
J
3
1
7
15
9
CN104
7
5
1
CN1901
6
CN9101
2
6
3
5
3
2
15
15
4
3
2
123
32
43
39-40
11-13
10 22
30
27
28
26 21
IC9702
21
IC9703
31
IC9703
57
IC9704
21
IC9201
31
IC9705
21
AK4586 NJM4558MD
(LPF) NJM4558MD (6dB AMP)
NJM2100M
IC9601
NJU7313AM
4
6
3
8
7
20
21 19
12
11
10
9
5
1
7
5
9
10 11
N
R
9
5
7
3
9
5
7
311
11
CN901
6
CN354
IC351
IC352 (Y SEL)
(C SEL)
8
R
V
CN901
3
CN107
1
5
8
K
(8 16bit)
FRONT
3. BLOCKDIAGRAM AND SPECIFICATIONS
3.1 BLOCKDIAGRAM

VSX-D711-K,VSX-D711-S
13
14.1/24.1 14.7/27.3 13.8
IC103
IC105
IC106
IC107
IC107
Q112 Q303
Q603
Q601
Q1552
Q653
Q651
Q632
Q631
UPC4570G2
(PRE AMP)
L
E
CN101
14
CN302
1
11
15
17
31
34
33
36
6
9
57
57
31
57
IC602
24 14
IC602
24 26
IC601 RY751
FL / FR
(SP–A)
SP–B
RY753
RY754
RY752
22 15
S
B
H
CN702 6
1551
6
CN106
4CN601
9
85
111
+12V
-12V D801–D804
IC801
T+12V IC805
CN101 IC802
NECK+B
POWER AMP
IC601, IC602
NECK-B
D702
D701
+BVL
+BVH
-BVH
-BVL
FL AC
FL AC
Q701
Q702
B
A
D+5V D721–D724
IC803
A+5V IC804
CN101 E
A
CN402
O
IC301
(CONPONENT SEL)
L
9
5
7
1
11
R
3
CN901
5
CN301
6
FRONT
T1
POWER
TRANSFORMER
T51
AC IN
U+5V
D51-D54
RY51
IC51
B
CN101
A
US591
MECHA SW ASSY

VSX-D711-K,VSX-D711-S
14
FRONT ASSY
(XWZ3498)
O
BOARD TO
BOARD
ASSY
(XWZ3575)
S. VIDEO
ASSY
(XWZ3522)
FRONT
VIDEO ASSY
(XWZ3515)
N
R
G
R.ENCODER
ASSY
(XWZ3511) P
D.D &
INPUT
ASSY
(XWX3047)
A
REGULATOR
ASSY
(XWZ3545)E
6CH IN ASSY
(XWZ3507)
M
VIDEO
ASSY
(XWZ3584)
FM/AM TUNER
MODULE
(AXQ7232)
L
V
HASHIGETA
ASSY
(XWZ3567)
F
AMP INPUT ASSY
(XWZ3550)
H
KAWA
ASSY
(XWZ3529) K
A1/4,
A2/4,
A3/4,
A4/4
3.2 OVERALL WIRING CONNECTION DIAGRAM

VSX-D711-K,VSX-D711-S
15
REK1026
(T2.5A)
DIGITAL IN
ASSY
(XWZ3518)
J
POWER SW ASSY
(XWZ3510)
Q
SU
H.P. ASSY
(XWZ3513)
TRANS3
ASSY
(XWZ3561)
DT
TRANS2
ASSY
(XWZ3558)
TRANS1
ASSY
(XWZ3553)
CI
AMP&
PRIMARY
ASSY
(XWZ3537)
B
J8
J7J6
J1J2
J4
J5
B1/2,
B2/2
TRANS4
ASSY
(XWZ3526)
MECHA SW ASSY
(XWZ3514)
VDG1076 : VSX-D711-K /MVXJI
VDG1077 : VSX-D711-K /MYXJIEW,
/MYXJIGR
VSX-D711-S /MYXJIEW
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".

VSX-D711-K,VSX-D711-S
16
A
B
C
D
1234
1234
A 1/4
3.3 DD & INPUT ASSY(1/4)
D.D & INPUT ASSY
(XWX3047)
A1/4
CN901
R
A2/4
CN802
E

VSX-D711-K,VSX-D711-S
17
A
B
C
D
5678
5678
A 1/4
CN402
O
A2/4
A4/4
A4/4
A2/4,4/4
A4/4 A2/4,3/4,4/4
A2/4 A2/4,3/4
CN1002
F
CN307
M
: The power supply is shown with the marked box.
( )
: AUDIO SIGNAL ROUTE

VSX-D711-K,VSX-D711-S
18
A
B
C
D
1234
1234
A 2/4
3.4 DD & INPUT ASSY(2/4)
D.D & INPUT ASSY
(XWX3047)
A 2/4
A1/4
A4/4
A1/4
A1/4
A3/4
CN1901
J
A3/4
A1/4

VSX-D711-K,VSX-D711-S
19
A
B
C
D
5678
5678
A 2/4
FRONT
SURROUND CENTER
SW
14.1 / 24.1 14.7 / 27.3 13.8
GAIN
(dB)
15K
15K
15K
15K
15K
1.2K
CN254
H
A1/4
A1/4
A1/4 A1/4
A1/4
( ) : AUDIO SIGNAL ROUTE

VSX-D711-K,VSX-D711-S
20
A
B
C
D
1234
1234
A 3/4
3.5 DD & INPUT ASSY(3/4)
D.D & INPUT ASSY
(XWX3047)
A3/4
A1/4