Pioneer VSX-5000 User manual

Opera ting
Instructions
VSX-5000
Boome oo ooo
oe SSS Eeeles ea BS SSs55
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will
know how to operate your mode! properly. After you have
finished reading the instructions, put them away in a safe
place for future reference.
In some countries or regions, the shape of the power plug and
power outlet may sometimes differ from that shown in the ex-
planatory drawings. However, the method of connecting and
‘operating the unit is the same.
This unit is provided with a demonstration mode func-
tion; for details, see page 2.
AUDIO/VIDEO STEREO RECEIVER
VSxX-5000
VSX-4000
ASOS
WARNING: To prevent FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear
panel. Please write this serial number on your enclosed war-
ranty card and keep it in a secure area. This is for your securi-
ty.
[CONTENTS
Before operating, adjust the position of these switches ............ 3
F@QtUI66: 6. coca sic ncadse cen csscdsaceds cceetsokeondacnenakscesansonesessostavees 3
Checking accessory items . ies ose 3
Surround SyStOm ...:c.csccsscesscceceeeteeeiseesvivceensersuvsderesencesness 4
Three-way surround processor (VSX-5000 only) ..........2sseeeeeres 4
Three-way sound effects FUNCTION ......5...cceeseseceene er Pri)
5
6
8
8
9
Inserting the batteries into the remote control unit
- Rear panel facilities ............eeceeees
Audio system connections
Audio adaptor connections (surround) .........c0.sseeeeeee
Audio adaptor connections (front) (VSX-5000 oni) eaves ies
Video system CONNECTIONS ......5...ccccecieeescncteccneeterees eee 10
Video adaptor connections (VSX-5000 only) .........seseceeeeeeeees
One VCR connection
Front panel facilities
Remote contro! unit operation
[For Canadian model]
CAUTION: to prevent ELECTRIC SHOCK DO NOT
USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: pour prevenir LES CHOCS ELEC-
TRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC
UN PROLONGATEUR UNE PRISE DE COURANT OU UNE
AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT
ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE
A DECOUVERT.
Preparations for broadcast sense seccscceseseadoceetescesesosesens 19
Preset tuning. han Fe 21
Displaying station call- ‘ettee: a. 22
To listen to other MUSIC SOUTCES .........scereerreceeenensetenecreeseene 23
Receiving FM simulcast TV programs ........ssesceneseeneesensecceees 23
Using a TV set to watch programs
from connected video COMPONENTS .........cieveereceseeeeereeeeees
To perform recording with a tape deck
Hi-Fi video recording
Video tape COPYING ........sseeeeeeenee
Using the video signal selector
Block diagram ........cccsscccerescersee
Hints for better reception
Troubleshooting ...........06 ae
Specifications ........cccccescccssnsenressscnsesseccceceeeesessessesesabons
PIONEER’
435.

READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
appliance is operated.
RETAIN INSTRUCTIONS — The operating instruc-
tions should be retained for future reference.
HEED WARNING — All warnings on the appliance
and in the operating instructions should be adhered
to.
FOLLOW INSTRUCTIONS — Ail operating and use
instructions should be faliowed.
WATER AND MOISTURE — The appliance should
not be used near water — for example, near 2
bathtub, washbow/, kitchen sink, laundry tub, in 2
wet basement, or near a swimming pool, etc.
LOCATION — The appliance should be installed in a
stable location.
WALL OR CEILING MOUNTING -— The appliance
shoutd not be mounted to a wall or ceiling.
VENTILATION — The appliance should be situated so
that its location or position does not interfere with
its proper ventilation. For exemple, the appliance
should not be situated on a bed, sofa, rug, or
similar surface that may btock the ventilation open-
ings; or, placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of
air through the ventilation openings.
HEAT — The appliance should be situated away from
heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers)
that produce heat.
POWER SOURCES — The appliance should be con-
nected to a power supply only of the type describ-
ed in the operating instructions or as marked on the
appliance.
POWER-CORD PROTECTION — Power-supply cords
shoutd be routed so that they are not likely to be
walked on or pinched by iterns placed upon or
against them, paying particular attention to cords
at plugs, convenience receptacles, and the point
where they exit from the appiiance.
POLARIZATION — If your purchased product is pro-
vided with a polarized power plug, please read the
following instructions. This product is equipped
with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way, This isa
safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized piug.
CLEANING ~ The appliance should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or
other volatile liquids since. they may corrode the
cabinet.
IMPORTANT
The lightning flash with arrowhead, within an
equilateral triangle, is intended to alert the user of the
_presence of uninsutated “dangerous voltage” within the
to constitute a risk of electric shock to persons.
are shown on the display panel.
To start the demonstration mode:
POWER switch.
VOLUME > MIN
2
<ARB1030>
This unit is provided with a demonstration mode
When this function is used, the various indicator functions
1. Set to the STAND-BY (Power OFF) condition.
2. While holding the TV ANT switch pressed, press the
e After all the display indicators light, operation begins,
and the controls will be set as follows:
SAFETY
INSTRUCTIONS
POWER LINES — An outdoor antenna should be
located away from power lines.
NONUSE PERIODS — The power cord of the ap-
pliance should be unplugged from the outlet when
jeft unused for a long period of time.
OBJECT AND LIQUID ENTRY — Care should be
taken so that objects do not fall and liquids are not
spilled into the enclosure through openings.
DAMAGE REQUIRING SERVICE — The appliance
should be serviced by Pioneer authorized service
center or qualified service personnel when:
*® The power-supply cord or the plug has been
damaged; or
© Objects have fallen, or liquid has been spilled | into
the appliance; or
© The appliance has been exposed to rain; or
© The appliance does not appear to operate normally
or exhibits a marked change in performance; or
e The appliance has been dropped; or the enclosure
damaged.
SERVICING — The user should not attempt to service
the appliance beyond that described in the
operating instructions. For alt other servicing, con-
tact the nearest Pioneer authorized service center.
SERVICE-ENTRANCE
EQUIPMENT
POWER SERVICE
GROUNDING ELECTRODE SYSTEM
fe.g. smteror meisl water pepe)
ANTENNA
DISCHARGE UNIT ¢
OPTIONAL ANTENNA
GROUNDING ELECTAODE
OUTDOOR ANTENNA GROUNDING — If an
outside antenna is connected to. the antenna
terminal, be sure the antenna system is
grounded so as to provide some protection
against voltage surges and built up static
charges.
in the U.S.A. section 810 of the National Elec-
trical Code, ANSI/NFPA No. 70-1984, pro-
vides information with respect to proper
grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an anten-
na discharge unit, size of grounding conduc-
tors, location of antenna-discharge unit, con-
nection to grounding electrodes, and re-
quirements for the grounding electrode. See
Fig. A.
a) Use No. 10 AWG (5.3 mm?)
copper, No. 8 AWG (8.4
mm?) aluminum, No. 17
AWG (1.0 mm’) capper-
clad steel, bronze wire, or
larger as ground wire.
b) Secure antenna lead-in and
ground wires to house with
stand-off insulators spaced
from 4 feet (1.22 meters) to
6 feet (1.83 meters) apart.
c) Mount antenna discharge
ANTENNA unit as closely as possible to
en
we
where
lead-in
enters
house.
STAND OFF
INSULATORS b
10 EXTERNAL ANTENNA ir wire not smaller
TERMINALS OF PRODUCT d} Use j jumpei wire
than No.6 AWG (13.3 mm*)
copper or equivalent when
separate antenna-ground-
ing electrode is used.
GROUND
WIRE a,b
BOND!
DRIVEN
@
FEET
(2.44
mt
Soren
—wro
YHE
EARTH
IF
REQUIRED LA
t LOCAL COOES. SEE
NEC SeEHON 810.21 tn.
FIG.A u
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SEAVICEABLE PARTS INSIDE_REFER -SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
DEMONSTRATION MODE
BALANCE > CENTER
SURROUND
VOLUME
(VSX-5000
only)
>
MID
The
exclamation
point
within
an
equilateral
triangle
is
intended
to
alert
the.
user
of
the
presence
of
important
operating
and
maintenance
(servicing)
instructions
in
ature-accompanying-the. appliance. .
TONE — FLAT (normal)
This
mode
will
continue
until
any
switch
other
than
the
MASTER
VOLUME
(VOLUME)
switch
is
pressed.
By
setting
the
desired
volume,
this
mode
can
be
main-
tained.
Also,
if
you
press
any
switch
other
than
the
MASTER VOLUME (volume),
the unit will stop.
~,

oa
BEFORE
OPERATING,
ADJUST
THE
POSITION
OF
THESE
SWITCHES
i
TWO VOLTAGE SELECTOR SWITCHES
Only
multi-voltage
models
are
provided
with
these
swit-
ches.
U.S.,
Canadian,
European,
U.K.,
and
Australian
models
are
not
provided
with
these
switches.
The
line
voltage
selector
switches
are
on
the
rear
panel.
Before
your
model
is
shipped
from
the
factory,
these
switches
are
set
_
to
the
power
requirements
of
the
destination.
Check
they
are
set
properly
before
plugging
the
power
cord
into
the
household
wall
socket.
If
the
voltage
is
not
properly
set
or
if
you
move
to
an
area
where
the
voltage
requirements
differ,
adjust
the
selector
switches
as
follows.
1. Use a medium-size screwdriver.
2.
First,
insert
a
screwdriver
in
the
groove
of
the
voltage
selector
at
the
right,
and
adjust
so
that
the
tip
of
the
groove
points
to
the
voltage
value
of
your
area.
3. Next, insert a screwdriver in the groove of the voltage
selector at the left and adjust until the voltage is the same
as at the right. |. ==
120v
220v~
260v
110v«120¥
Medium-size screwdriver
NOTE:
Both switches must be in the same switch setting.
FEATURES
CHANNEL
STEP/FM
DE-EMPHASIS
SWITCH
The
unit
has
been
factory
preset
to
the
channel
allocation
and
de-emphasis
value
for
the
area
in
which
it
is
to
be
sold.
If
these
values
are
set
incorrectly,
the
frequency
display
may
stop
at
the
wrong
frequency,
or
sound
may
be
distorted,
resulting
in
an
inability
to
reproduce
reception
signals
at
their
proper
sound
quality.
For
this
reason,
be
sure
to
confirm
that
the
values
are
set
correctly
before
first
using
the
unit.
[100
kHz/10
kHz/75
us}
position:
Set
to
this
position
for
areas
with
FM
reception
step
of
100
kHz,
AM
10
kHz,
and
de-emphasis
75
ys.
{50 kHz/9 kHz/50 ys] position:
Set
to
this
position,
for
areas
with
FM
reception
step
of
50
kHz,
AM
9
kHz,
and
de-emphasis
of
50
ps.
NOTE:
When
unsure
about
the
channel
allocation
and
de-emphasis
values
for
your
area,
consult
your
dealer
for
correct
information.
w-—— CHANNEL STEP——— 4
SOkHz a FM om | OOKHZz
9kHz AM 10kHz
|
=
50zS 75uS
LW. FM DE-EMPHASIS ——I
The
VSX-5000/4000
is
an
audio-visual
component
combining
the
functions
of
receiver,
wireless
remote
control,
audio-video
selector,
surround
processor
and
video
enhancer.
It
will
play
a
central
role
in
your
enjoyment
of
audio-visual
media.
e SURROUND FUNCTION
VSX-5000:
Three
surround
modes
(Dolby
surround,
Stadium,
Studio)
can
be selected.
VSX-4000:
Provided
with
surround
function
utilizing
the
speaker
matrix.
e ENHANCER, SPLIT-SCREEN FUNCTION
The built-in detail-type enhancer is beneficial when making
copies of VCR tapes. Also, by using the split-screen function,
you can simultaneously view the enhanced and original (non-
enhanced) images. In this way you can select the optimum
settings for enhancing the image.
¢ CABLE FM FUNCTION
in
areas
where
cable
FM
(stereo)
broadcasts
are
transmitted
simultaneously
with
CATV
broadcasts,
this
function
allows
you
to
enjoy
the
CATV
broadcast
in
living
stereo.
In
addition,
by
using
the
unit's
simulcast
function,
stereo
recording
can
be
performed
with
Hi-Fi
VCR
units.
¢
VIDEO
SIGNAL
SELECTOR
(Simulcast
function)
Allows
free
combination
of
various
audio
and
video
sources
during
playback
and
over-dubbing,
enabling
you
to
produce
your
own
original
background
videos.
©
TWO-WAY
VCR
COPYING
AND
MONITORING
VCR
1—VCR
2:
Copying
of
video
cassette
tapes
can
be
per-
formed
in
either
direction.
VDP/VCR
3—VCR
1,
VCR
2:
Allows
simultaneous
production
of
two
copies
from
a
single
video
cassette
tape
or
video
disc.
e ACOUSTIC MEMORY FUNCTION
Three
types
(A,
B,
C)
of
tone
control
setting
can
be
preset.
The
setting
of
loudness
and
flat
tone
response
functions
can
also
be
selected
quickly.
¢
STATION
CALL-LETTER
DISPLAY
FUNCTION
The
call-letters
of
broadcast
stations
can
be
preset
(up
to
four
characters).
The
display
can
be
set
to
show
either
the
broad-
casting
frequency
or
the
call
letters
(for
example
WBAC).
The
four-character
display
can
alternately
be
set
to
dispiay
your
name,
or
the
type
of
material
broadcast
(for
example,
JAZZ,
NEWS,
etc.).
CHECKING
ACCESSORY
ITEMS
AM Loop Antenna
FM T-type Antenna
Remote contro! unit
Dry cell battery x 2
3
<ARB1030>

SURROUND SYSTEM
What is surround sound?
With ordinary. stereo, sound normally comes only from
speakers in front of the listener. In a concert hall or theater
though, sound reflected from the walls and ceiling reaches the
listener from all directions. This is what accounts for the feel-
ing of ambience or spaciousness of a live performance. Sur-
round sound works to reproduce these effects to provide
fuller, more “live” sound.
Speaker System Placement Examples
The sound effects obtained in a surround system depend on
speaker placement. Experiment with various arrangements to
find the one most suited to your tastes.
Placing the speakers so that they are slightly higher than ear-
level contributes to sound quality.
Constructing a Surround System
Example A:
FRONT
SURROUND
Ye
de
VSX-5000:
[Example A: Suitable for STUDIO use]
Sound appears to come from directly in front of listener. Good
for listening to music recordings.
[Example B: Suitable for STADIUM] |
Offers most varied effects; good for watching sports programs
or listening to live recordings.
[Example C: Suitable for Dolby surround]
Good sound dispersion; recommended for movies, etc.
EFFECT CHART
fs Hie od
SURROUND
smo | Oo | o
VSX-4000:
For a music tape, the optimum system layout is as shown in
example A; for a tape of a sporting program, the optimum
layout is as shown in example B; and for a movie tape, the op- C
timum layout is as shown in example C. /
Example B: Example C:
ae
FRONT
Ma eed
Listening ares
SURROUND
SURROUND
THREE-WAY SURROUND PROCESSOR (VSX-5000 only)
DOLBY SURROUND
This is the optimum setting for viewing recent movies,
especially those featuring the DOLBY STEREO trademark.
Normal stereo sound is reproduced from the front speakers,
while the rear speakers reproduce the surround signal. This
can also be used when watching television programs, video
cassette tapes and video discs. It is also effective when playing
back recorded video tapes of television programs.
NOTE:
With television broadcasts, this function is effectively only with
video tapes recorded in stereo.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under one or more of the
following patents: U.S. numbers 3,632,886, 3,746,792 and
3,959,590; CANADA numbers 1,004,603 and 1,037,877. “Dolby”
and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Manufacturé sous licence de Dolby Laboratories Licensing Cor-
poration. En outre, sous license d’un ou plusieurs des brevets
suivants: numéros américains 3,632,886, 3,746,792 et 3,959,590;
numéros canadiens 1,004,603 et 1,037,877. Le terme “Dolby” et le
symbole Double-D sont des marques déposées de Dolby
Laboratories Licensing Corporation.
4
<ARB1030>
STADIUM
When watching live broadcasts of sporting events, this func-
tion allows you to enjoy play-by-play action with the effect of.
surround sound, just as if you were present in the stadium. ©
STUDIO
Effective when watching movies or for listening to music con-
cert sources. In addition to the normal stereo reproduction
from the front, the rear surround speakers add the ambience
of a theater or concert hall’s acoustic resonance. The effect is
as though you had prime orchestra box seating.

a
THREE-WAY SOUND EFFECTS FUNCTION
VCR NOISE FILTER
When playing back a monaural VCR, there is a tendency for
audible high-frequency hiss noise to be produced.
When playing back video tapes, if the audio channels contain
noticeable high-frequency tape hiss noise, pressing this switch
will improve the sound.
DYNAMIC EXPANDER (VSX-5000 only)
This
function
expands
the
dynamic
range
of
playback
sounds,
thus
giving
life
and
impressive
force
to
music
sources,
and
resulting
in
a
sense
of
ambience
and
presence.
In
particular,
when
used
with
rock
or
jazz
music
playback,
the
music
achieves
a
breadth
with
naturalness
of
vocal
reproduction
and
clearly
contoured
instrumental
sounds,
thus
producing
a
feel-
ing
of
live
presence.
SIMULATED STEREO
This
function
transforms
monaural
signals
into
simulated
stereo
sound.
Use
it
when
you
wish
to
experience
the
sense
of
stereo
presence
when
listening
to
AM
broadcasts,
or
VCR
and
other
monaural
signal
sources.
NOTE:
The
simulated
stereo
function
can
also
be
used
with
stereo
sound
sources,
but
it
will
result
in
an
effect
somewhat
different
from
the
normal
stereo
sound.
STEREO WIDE (VSX-4000 only)
Used
with
stereo
sources,
this
function
results
in
an
even
wider
breadth
and
stereo
presence.
INSERTING
THE
BATTERIES
INTO
THE
REMOTE
CONTROL UNIT
=
yt
ae
~
ay
-
{1] Remove the cover of the battery compartment on the
reverse side of the remote control unit. This can easily be
done by pressing down on the cover with your thumb and
pulling it in the direction of the arrow.
[2] Take out the two size “AAA” [IEC RO3 (UM-4)] dry cell
batteries supplied and load them into the battery compart-
ment, taking care to follow the markings on the compart-
ment.
[3] Replace the cover of the battery compartment.
Cautions for handling dry cell batteries
Misusing dry cell batteries can result in electrolyte leakage or
explosions. Bear in mind the following points for getting the
most out of your batteries.
© When loading the batteries into the battery compartment,
make sure the plus ® and minus © polarities correspond
to the markings on the compartment.
e Even though they may be the same shape, batteries come
with different voltage ratings. Do not mix or use different
types of batteries together. Use only the same kind of bat-
teries.
¢ Do not mix up new batteries and used batteries but replace
all the batteries at the same time.
¢ Do not heat, disdssemble or shortcircuit batteries or throw
them into a fire.
e¢ Some batteries are rechargeable while others are not.
Observe the cautionary notes on the batteries and use them
properly.
Range
of
remote
control
|
When
the
remote
control
unit
is
pointed
at
the
remote
con-
trol
sensor
window
on
the
receiver
and
any
of
its
keys
is
pressed,
the
unit
and
other
components
can
be
operated
by
remote
control.
Distance:
Within
a
range
of
about
7
meters
from
the
unit’s
remote
control
sensor
window
Angle:
Within
approx.
30
degrees
from
the
center
of
the
unit’s
remote
control
sensor
window
Remote
control
will
not
be
possible
if
there
is
an
obstacle
between
the
remote
control
unit
itself
and
the
unit’s
remote
control
sensor
window.
Remote control
sensor window
Bringing
the
remote
control
unit
closer
to
the
sensor
window
in-
creases
the
angle
that
enables
remote
control.
Ss
<ARB1030>

REAR
PANEL
FACILITIES
To simplify the explanation, the illustration shows the facilities
provided on the VSX-5000 and VSX-4000.
FM/AM
ANTENNA
terminals
:
Use
these
antenna
terminals
for
reception
of
normal
FM
and
AM
broadcasts.
©
For
details
regarding
antenna
connection,
see
the
section
“Hints
for
Better
Reception”
on
page
28.
ANTENNA
FM-B
(CATV)
terminal
Use
this
antenna
terminal
for
reception
of
CATV
FM
broadcasts.
Connect
a
75-ohm
coaxial
cable
to
this
terminal.
INPUT jacks
PHONO
...
Connect
to
the
output
cables
from
a
turntable.
CD
...
Connect
to
the
output
jacks
of
a
compact
disc
player.
TAPE jacks
The
REC/PLAY
jack
on
the
receiver
consists
of
two
sets,
TAPE
1
and
TAPE
2.
It is
possible
to
connect
two
tape
decks
to
the
receiver
and
do
simultaneous
recording
or
tape
to
tape
record-
ing.
When
connecting
only
one
tape
to
the
receiver,
connect
it
to
the
TAPE
1
jack.
Connecting for Recording
The
tape
recording
jack
(TAPE
REC)
on
the
tape
deck
should
be
connected
to
the
REC
side
of
the
TAPE
jack
on
the
receiver
with
a
pin
plug
connecting
cord.
Connecting for Playback
Connect
the
TAPE
PLAY
jack
on
the
tape
deck
to
the
PLAY
side
of
the
TAPE
jack
on
the
receiver
with
a
pin
plug
connecting
cord.
GND terminal
Connect the ground lead of a turntable to this terminal:
VIDEO ADAPTOR jacks (VSX-5000 only)
Use to connect a video adaptor component such as a video
enhancer or color corrector.
VDP/VCR 3 jacks
[VIDEO IN)
When
watching
the
video
image
from
a
LaserVision
player
(VDP)
or
a VCR
used
for
playback,
connect
its
VIDEO
OUTPUT
jacks
here.
[AUDIO IN (L, R)J
When playing back the audio channel from a LaserVision player
VCR 2 jacks
[VIDEO OUT] ;
When copying program materials from the video component con-
nected to the VCR 1 or VDP/VCR 3 jacks, connect to the VIDEO
INPUT jacks of the VCR used for recording.
[AUDIO OUT (L, RJ
When copying program materials from the video component con-
nected to the VCR 1 or VDP/VCR 3 jacks, or when recording
music from an audio component source, connect to the AUDIO
INPUT jacks of the VCR used for recording.
=}
<ARB1030>
SURROUND POWER AMP IN jacks
(VSX-5000 only)
When a separate pre-amplifier is connected and VSX-5000 is used
as power amplifier for surround ‘speakers, connect the pre-
amplifier to these jacks.
(Standard input 150 mV, Impedance 50 k2)
SURROUND PRE-AMP OUT jacks
(VSX-5000 only)
When a power amplifier is used to connect surround speakers,
connect the power amplifier to these jacks.
(Standard output 150 mV, Impedance 470 2)
SURROUND BALANCE control
(VSX-5000 only)
Use to adjust the surround effect from the surround speakers.
Normally leave in the center position. When inputting a monaural
signal, adjust so that the surround output is minimum.
REMOTE CONTROL IN/OUT jacks
IN: Connect this jack to other Pioneer components (main unit or
remote control unit) when using those components to con-
trol this unit.
OUT:
Connect
this
jack
to
other
Pioneer
components
when
using
this unit’s remote control to control the other components.
VCR 1 jacks
[VIDEO OUT]
When copying program materials from the video component con-
nected to the VCR 2 or VDP/VCR 3 jacks, connect to the VIDEO
INPUT jacks of the VCR used for recording.
[AUDIO OUT (L, R)J
When copying program materials from the video component con-
nected to the VCR 2 or VDP/VCR 3 jacks, or when recording
music from an audio component source, connect to the AUDIO
INPUT jacks of the VCR used for recording.
[VIDEO IN}
When monitoring the video image from a VCR used for playing,
connect its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
When monitoring back the audio channel from a VCR used for
playing, connect its AUDIO OUTPUT jacks here.
[VIDEO IN]
When monitoring the video image from a VCR used for copying,
connect its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
When monitoring the audio channel from a VCR used for copying,
connect its AUDIO OUTPUT jacks here.

L+R output jacks (VSX-5000 only)
These are the Dolby surround center channel signal output jacks.
They can also be used as a 3D system MONO output.
(Standard output 1 V, output impedance 4.7 KQ.)
SPEAKERS terminals
A: Connect to a first set of speakers (or the front speakers in a sur-
é round system).
B: Connect to a second set of speakers (or the surround speakers
| in a surround system)
The words in parenthesis apply to when the SURROUND
ON/OFF selector switch is ON.
Speaker iead wire preparation and connection
Cutter
x aes Speaker cord
bad mm Twist ma strands
a Push up irae! Jeu
Rout ® Insert &
NOTE:
Do not allow any of the cord’s conductors to protrude from the
terminals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact
with each other.
| Or@®
entur | hae
=e Power cord
FRONT POWER AMP IN jacks
(VSX-5000 only)
When a separate pre-amplifier is connected and the VSX-5000 is
used as power amplifier, connect the pre-amplifier to these jacks.
(Standard input 1 V, input impedance 50 kQ)
FRONT PRE-AMP OUT jacks
(VSX-5000 only)
When a separate power amplifier is used to connect the front
|__ Speakers, connect the power amplifer to these jacks.
(Standard output 1 V, output impedance 470 &)
VIDEO OUT jacks
Use to connect a TV set for watching program materials from the
VCR or VDP connected to this unit.
[TO MONITOR TV jack]
Connect to a monitor TV or to a TV set with video input terminals.
[TO.RF MODULATOR jack]
Use to connect a normal TV set. When performing connections,
the RF MODULATOR JA-RF5 (sold separately) is required. By
connecting an RF modulator, video signals can be converted to
VHF signals (U.S. channel 3 or 4), thus allowing this unit to be
used to view the selected source on a normal television set.
AC OUTLETS
(SWITCHED) TOTAL 300 W MAX
Power supplied through these outlets is turned on and off by the
receiver’s POWER switch. Total electrical power consumption of
connected equipment should not exceed 300 W.
(UNSWITCHED) 200 W MAX
Power flows continually to this outlet, regardless of whether the
receiver is switched ON or OFF. Electrical power consumption of
the connected equipment should not exceed 200 W.
The-equipment should be disconnected by removing the main plug
from the wall socket when not in regular use, e.g. when on vaca-
tion.
NOTE:
Do not connect appliances with high power consumption such
as heaters, irons, or television sets to the AC OUTLETS in order
to avoid overheating or fire risk.
This can cause the receiver to malfunction.
SPEAKER IMPEDANCE selector switch
Set this switch to the nominal impedance of your speakers. When
using surround speakers, or when two sets of speakers are used
together, each set of speakers should have a nominal impedance
of 8—16 ohms. When connecting surround speakers, always set
to position @.
When SURROUND ON/OFF selector switch is ON position:
cm Norminal speaker When using
impedance Surround Speaker
From 4 to less than 8 Q [
Smet 8 to less than 16 Q
When SURROUIS ORTOP aor ON/OFF selector switch is OFF bere
ace (A or La alone together (A + B)
[ométolew
then
88]
Postion
@®
|_|
Pea | rien | Pon
If speakers are used in ways other than those shown above, the
speakers may not deliver proper output, or unnecessary heating
may be caused.
SURROUND ON/OFF selector switch
When surround speakers are connected to the SPEAKER B ter-
minals, set to the ON position; in all other cases, leave in the OFF
position. When set to the ON position, the SURROUND mode can
be selected with the unit’s main controls or with the remote con-
trol unit.
Before operating this switch, read the explanation on the
CDrAVOD IRADOCNAAICE «nln nene o..-4-b
| Ur LANGnN vir CUMING Sticcior Switth. ;
SURROUND LEVEL selector switch
(VSX-4000 only)
By selecting one of the three positions (L: Low, M: Mid, H: High),
the sound volume from the surround speakers can be changed.
NOTE:
A “normal TV set” as noted above is one for which RF connec-
tions alone are possible.
7
ar <ARB1030>

AUD
10
SYSTEM
CO
NNECTION
Ss
ated
psa
on
pages
8
to
11
show
the
rear
of
the
TO FM CATV channel ve
CATV
fine
CS
AM
LOOP
ANTENNA
°
se
4
*
Unfold
all
four
legs
of
the
AM
Loop
anten-
=
Twist
the
na
toward
the
outside,
and
insert
the
iz
strands
together.
stopper
inside
the
legs
into
the
hole
in
the
EE:
T
i.
AM
Loop
antenna
to
fix
it
in
position.
t
7
.
ao
*
Set
the
antenna
on
a
level
surface,
and
TO VHF INPUT Jack L 10608 5 point it in the direction that gives op-
(c.f
TV.VER
etc)
po
2
7
timum
reception.
* Do not install the antenna in locations
where it touches the cover of the tuner or
other metal objects, or near a CD player,
personal computer, or television set.
fe ea lool em | lod = [22
see Seoccela
iil ae\oe eee?
SPEAKERS SYSTEM A
gy FRONT SPEAKERS
“gps
o\ lay SPEAKERS SYSTEM B
Ds REAR SPEAKERS
AUDIO ADAPTOR CONNECTIONS (Surround)
(VSX-5000 only)
e When boosting the power
from the surround side by
using another stereo
amplifier
_ Stereo Power Amplifier.
Power cord
@ Set SURROUND ON/
OFF selector switch
to ON when using
‘the receiver surround
function
Connect to a
SWITCHED OUTLET.
Connector bar
Remove both
connector bars.
ER
© (ololoioro)
gee eiees l=
@® DO ®O|© GOO@|@
Nes ee oe eet een oe _Y
© When using the receiver surround
8 function
<ARB1030> =

AUDIO ADAPTOR CONNECTIONS (Front) (VSX-5000 only)
When using the preamplifier of the receiver and using a When using the power amplifier of the receiver and using a
separate stereo power amplifier to increase power separate stereo preamplifier.
© [olololelo) lool om |
oaee GOOO® eal
COG O@ ores
lool ealg
AIGooon Hears
SBS ©O@|© odeoes
ssesesiosrecl
loele ©® og Ol
id
=
ron
\ Connector bar
Remove both
e) (Ome) O B Connect to a connector bars.
ower cord swiTCHED OUTLET
Stereo
PowerAmobfiar
Stereo
preamplifier
[Application example] Precaution regarding installation position of cassette
tape deck
If the cassette tape deck is installed in the position shown in
MULTI-AMPLIFIER SYSTEM z ‘3
PE the drawing below (NO GOOD positions), hum may occur dur-
Crossover Network ing playback.
KM
NO
GOOD
Power Amplifier
NO GOOD
flo] =| | Receiver. |
oe ee
1 8
NO GOOD
H a CI_| Tweeter
Receiver |
: aq Woofer
. PRE. AMP POWER AMP. lox
Speaker system
=)
<ARB1030 >

VIDEO SYSTEM CONNECTIONS
To UHF antenna
IN OUT IN
o 88 @ 8
VIDEO
To VHF antenna
AUDIO
AUDIO
l@ Red plug
aug White plug all
vineoy
Ba ,rellow plug
e Connect the plugs properly. Faulty
connections can cause noise and
also breakdowns and failures.
as =i ne Wh ae
ee OVOv @} isk
seeesep ®|® st iS @ e109) REE
4 To VHF antenna ae
te
RF MODULATOR JA-RF 5
(Sold Separately)
VIDEO ADAPTOR CONNECTIONS (VSX-5000 only)
e Example:
When using video enhancer, Video enhancer
f : S| VIDEO "| I Enhancer effected
Video signal IN OUT video signal
10
<ARB1030->

ONE VCR CONNECTION
VCR + Normal TV or Monitor TV
To UHF antenna
To VHF antenna
AUDIO
IN
AUDIO
(o BITES | ol Z |
ODODOSSO SH OSS
Hasna 9 eee
ae\eSoolad
CATV line
A,
T | Splitter
ar mpenanaae
iT
©
senea
le
4/2/19
@® BEBE OHO dee oe
LOX LOFOLOKS) Sdeoloel ©
eesegecogs .
looje|dsjoo
[=] @®
—
!
RF MODULATOR JA-RF5
(Sold Separately)
To VHF ANTENNA
Monitor TV
41
<ARB1030>

FRONT PANEL FACILITIES
SPLIT SCREEN control
This contro! allows you to freely control the area of enhanced pic-
ture (on right side of screen) and original picture (non-enhanced,
on left side of screen) by means of 4 vertical line dividing the
screen into two sections.
Screen to which
enhancer has
been applied
Screen to which
enhancer has not
been applied
SPLT SCREEN
SPLIT SCREEN SPLIT SCREEN
+ a o = a o = a S
NOTE:
This line is not output from the VCR (VCR 1 and VCR 2) VIDEO
OUT jacks. As a result, the split screen image is not recorded;
the recorded image will be entirely that produced by the
enhancer function.
ENHANCER control
When performing tape copying with a VCR, some deterioration in
image quality occurs normally. This contro! allows compensation
for this deterioration in image quality by emphasizing image detail.
NOTE:
The ENHANCER control functions to suppress image deteriora-
tion, but will not improve image quality beyond its original state.
SPEAKERS switches
These switches are used to select the speakers used.
A: To use the speakers connected to the SPEAKERS A terminals.
B: To use the speakers connected to the SPEAKERS B terminals.
When perform surround reproduction, press both of switches
A and B.
POWER STAND-BY/ON switch
When this switch is pressed, power is supplied to the unit. Press
the switch again to turn power off.
[Timer ON/OFF possible]
When the unit is switched ON, ON/OFF control can be performed
by means of the optional timer.
NOTE:
When the power is turned ON, muting will be applied to prevent
sound from being output while the volume level indicator is
SURROUND mode switch
Set in accordance with the music source used when performing
surround playback.
OFF: Press when not performing surround playback.
STUDIO: Optimum when watching movie or concert programs.
STADIUM: Optimum when watching live sports programs.
OCG SURROUND: Optimum when watching movie programs bear-
ing the DOLBY STEREO trademark.
NOTE:
© When the rear panel SURROUND ON/OFF selector switch is
in the OFF position, no surround effect will be produced even
if these switches are pressed. :
es (VSX-5000 only) *
12
" <ARB1030>
[When the switch marked * is pressed, characters
will appear on the display panel.]
SIMULATED STEREO switch *
Press to produce a simulated stereo effect when listening to
monaura! sources (for example normal AM or TV broadcasts).
“S/STEREO” appears on the display panel.
NOTE:
© ON the VSX-5000, this effect is not produced through the sur-
round speakers.
DYNAMIC EXPANDER switch *
(VSX-5000 only)
Press to add impressive dynamicity to rock or jazz music sources.
NOTE:
This effect is not produced through the surround speakers.
Remote signal sensor
VSX-5000
Renee een eT
PHONES jack
Connect the plug on your headphones to this jack. To fisten to a
program through the headphones, set both SPEAKERS A and B
switches to the OFF position.
VIDEO ADAPTOR switch (VSX-5000 only) *
Press when using the video component connected to the VIDEO
ADAPTOR jacks.
VIDEO ENHANCER switch «
Press when performing video copying with added video enhancer -—-—+
effects. When the switch is pressed, the monitored video image
will be the split screen picture.
VCR
MODE
STEREO/MONO
selector
switch
MONO:
All
playback,
including
stereo
signals,
are
produced
in
monaural.
When the MODE MONO indicator lights, the unit is set to the
MONO mode.
NOTE:
This switch can be used when one of the video system function
switches is selected. In addition, this switch can be preset for
either of VCR 7, VCR 2, or VDP/VCR 3. When any other audio
function switch is pressed, the mode mono is automatically
canceled.

[Refer to page 16 for VSX-4000.]
FRONT PANEL FACILITIES
ACOUSTIC MEMORY switch
Use to set sound quality to three different settings (A, B, or C).
This function allows you to preset and quickly recall frequently
used tone settings.
ACOUSTIC SELECT switch *
Each time this switch is pressed, acoustic effects are produced in
the following order:
fo ——» LOUDNESS ——» A——» B—e <
FLAT: For flat (normal) frequency response.
LOUDNESS: Emphasizes the low- and high-frequency ranges.
Produces a fuller sense of sound particularly when
listening at low volumes.
A, Bor C: Produces the sound tone preset with the ACOUSTIC
MEMORY switch.
ME UTATION CAG HANODM YOCH
wu 2 2 on 1,
uy
VIDEO SIGNAL SELECTOR switch
When recording simulcast programs, the recorded image can be
selected from among VCR 1, VCR 2, and VDP/VCR 3.
Audio/video function switches *
VCR 1: Press when performing playback on a VCR unit.
VCR 2: Press when performing playback on a second VCR unit. |
VDP/VCR 3: Press when performing playback on a video disc
player (VDP) or third VCR.
TAPE 1: Press when performing playback on a tape deck and
when monitoring recording.
TAPE 2: Press when performing playback on a second tape deck
and when monitoring recording.
This receiver has two sets of tape terminals, allowing you to con-
nect two tape decks for both recording and playback.
NOTE:
If TAPE 1 and TAPE 2 are pressed simultaneously, TAPE 2 alone
will function.
CD: Press when playing compact discs on a CD player.
PHONO: Press when playing records on a turntable.
Presetting the Acoustic Memory
TREBLE
—‘eass + 2
1. Use the ACOUSTIC SELECT switch to select the desired
memory position (A, B, or C).
2. Use the BASS/TREBLE controls to adjust the sound to the
desired tone quality.
3. Press the ACOUSTIC MEMORY switch.
¢ in this way, the desired tone will be preset in one of the three
acoustic memory positions. To preset two other desired tone
settings, perform the same operations.
© To recall the memorized tone settings, press the ACOUSTIC
SELECT switch to select the desired memory position. !n this
way, three different tone settings can be preset and recalled in
the three positions of the acoustic memory.
BASS/TREBLE controls
Use these controls to adjust the tone quality.
When both sides (+) of the BASS control are pressed
simultaneously, the bass response will be set to the flat (normal)
condition; likewise, when both sides (+) of the TREBLE control are
pressed simultaneously, the treble response will be set to the flat
(normal) condition.
MASTER VOLUME switch
Use to simultaneously adjust the sound volume from front and sur-
round speakers. To increase sound volume, press the ‘’+”’ side.
To reduce sound volume, press the ‘’—’’ side.
¢ The sound volume level is memorized even when the power is
turned OFF. When the power is turned ON again, the volume
will automatically return to the previously set level.
MUTE switch *
Press to temporarily cut off the sound volume. When pressed
again, the sound will return to its previous level.
MCR NOISE FIL] ER switch +.
ee eae
If tape hiss noise is noticeable when performing playback of video
Cassette tapes, press this switch to reduce the noise.
By pressing this switch, ’‘N FILTER” will appear on the display
panel.
NOTE:
© This switch can be used when one of the video system func-
tion switches is selected. In addition, this switch can be
preset for either of VCR 1, VCR 2, or VDP/VCR 3. When any
other audio function switch is pressed, the noise filter is
automatically canceled.
© The effectiveness in reducing high-frequency hiss noise
varies depending on the type of tape used, the recording
level, and other conditions.
ori Ouver we
13
<ARB1030>

FRONT PANEL FACILITIES
The indicators shown below light in the following cases.
Indicates the SOURCE selected by
the audio/video function switch.
Indicates the channel of the STA-
TION CALL switch. ~
ra Mia 07 4 CT We) Wit oT ot
i Oot a a He row yal EE EAT
FRONT
TREBLE
mT
y
acoustic
eae]
eo
SHES
==,
If
The TAPE 1, TAPE 2, and SUR-
ROUND modes are displayed in red
letters.
indicates which position A, B and C,
of the ACOUSTIC MEMORY is selected.
Normally, the left and right output
levels are displayed.
Also, when you adjust the bass and
treble, the ‘orresponding indica-
tions will be displayed.
When the
When the VIDEO
ADAPTOR is ON DYNAMIC EX-
(VSX-5000 only} PANDER is ON
When a video When the vcr 'VSX-5000 only} When the TUNING
source is selected mode is set to When i
by the VIDEO ONO SIMULATED Mode is AUTO
SIGNAL selector STEREO is ON
When the VIDEO
ENHANCER is ON
When the VCR
pg FILTER is
When the STEREO
WIDE is ON
(VSX-4000 only)
When LOUDNESS switch
is selected using
the ACOUSTIC
SELECTOR switch
AUTO/MANUAL
TUNING
selector
switch
*
This
switch
is
used
to
select
the
tuning
mode.
The
AUTO
tuning
mode
has
been
selected
when
the
TUNING
AUTO
indicator
lights.
AUTO tuning
When the — or + TUNING switch is pressed, the receiver
automatically scans the broadcast station frequencies. When a
broadcast is detected, the scanning stops at that frequency.
IVa at a
“TNWOTES " 7 7
By pressing the TUNING switch (— or +) while scanning is taking
place, scanning will stop.
MANUAL tuning
This is the usual tuning method. Each time the — or + TUNING
switch is pressed, the reception frequency is changed by one tun-
ing step. When pressed continuously, the receiver scans the
broadcast frequencies continuously.
DIRECT ACCESS TUNING switch
When this switch is pressed, the STATION CALL switches func-
tion as ten-key number switches for direct input of the desired
reception frequency.
14
<ARB1030>
When mode 2
iN
When the unit is
put in the station
channel mode us-
ing the FREQ/CH
Indicates SURROUND MODE, ON-OFF of ENHANCER,
ON-OFF of S/STEREO (SIMULATED STEREO), fre-
quency of broadcast station, call letter indication, LOUD-
NESS, FLAT, N FILTER (NOISE FILTER), S/WIDE
(STEREO WIDE), S/S+S/W (SIMULATED STREO
+ STEREO WIDE) etc.
WAN VANE JAN [rer]
j
Indicates
the
volume,
balance,
and
i
SLEEP time. When the unit is swit-
ched
ON,
the
sound
level
indicated
|
will flash, and muting will be applied
for
several
seconds.
|
|
1
VSX-5000
Q
PIONEER
scorvoce
no
meciEM
vie
tao
When an FM
STEREO broadcast When a broadcast
is received
When 8 (CATV) is
selected using the
FM ANT selector
switch
is
When the unit is
put in the TV
mode using the TV
ANT selector
switch
When the unit is
set in the monaural
mode when an FM
broadcast is being
received
BAND selector switches *
FM: Press for FM reception.
AM: Press for AM reception,
MEMORY switch *
When
the
unit
is
in
the
frequency
display
mode,
pressing
this
switch
will
result
in
the
memorization
of
the
current
broadcast
band,
reception
frequency,
~antenna—A/B—-mode,-
-and—FM-—
AUTO/MONO mode.
When
the
unit
is
in
the
station
call-letter
mode,
the
station
name
(call
letters,
etc.)
will
be
memorized.
STATION (1—10/11--20) selector switch
This
switch
is
used
to
set
the
STATION
CALL
switches
to
either
Mode
1
(1—10)
or
Mode
2
(11—20).
Mode
2
(11—20)
is
selected
when
the
switch
is
pressed
so
that
the
STATION
(11—20)
in-
dicator is lighted.
NOTE:
Changing
the
position
of
this
switch
has
no
effect
on
receiver
performance itself.

FRONT PANEL FACILITIES
FREQ/CH (Frequency/Channel) switch
This switch is used to select either the station frequency mode or
station channel mode for the broadcasting station shown on the
display panel. When “CH” is displayed, the unit is in the channel mode.
TUNING switch ;
' Use to perform tuning in accordance with the setting of the
FREQ/CH switch.
[Station Channel Mode] (for preset scanning)
+: Performs tuning of the stations preset in the STATION CALL
switches in the ascending numerical order of the switches.
-: Performs tuning in the same way, only in descending
numerical order of the STATION CALL switches.
{Station Frequency Model] (for normal tuning)
+: Performs tuning from the currently displayed station frequen-
cy in ascending frequency order.
~: Performs tuning in order of descending frequencies.
FM MODE AUTO/MONDO selector switch
Use to select the auto stereo mode or monaural mode when listen-
ing to FM broadcasts. The monaural mode has been selected
when the FM MODE MONO indicator is lighted.
Auto stereo mode:
Normally leave in this mode for reception. When a stereo FM
broadcast is received, it will be automatically reproduced in stereo
sound,
Monaural mode:
When receiving distant stations or stations with weak broadcast
signals, the input signal may be weak, thus resulting in increased
noise during FM stereo broadcasts. in this event, setting the
receiver to the monaural mode will reduce the noise. In this case,
_however,. FM_stereo broadcasts will be reproduced in monaural_j
sound.
NOTE:
This switch has no effect on reception of AM broadcasts.
STATION FREQ/NAME (frequency/call-letter)
selector switch
Use to select either the station call-letter mode or station frequen-
cy mode. The respective modes are shown on the display panel.
Station call-letter mode:
Displays the four-character station call-letters optionally selected
(only when preset tuning mode is used).
Station frequency mode:
Displays the broadcasting station frequency.
_ These switches are used to preset and recall desired broadcasting
mode; they are also used when performing direct access tuning.
SURROUND VOLUME switch (VSX-5000 only)
This switch is used to preset the sound level difference between
front and surround speakers. In this way, after presetting the dif-
ference, the overall volume of front and surround speakers can be
changed by using the MASTER VOLUME switch, while still main-
taining the sound volume differential.
— side: Surround speaker volume is reduced.
+ side: Surround speaker volume is increased.
NOTE:
This switch does not function when the surround switches are
OFF.
BALANCE switches
Use to adjust the sound volume balance between left and right
speakers.
LEFT: Press to decrease the sound on the right side.
RIGHT: Press to decrease the sound on the left side.
NOTE:
The left-right sound volume balance cannot be adjusted in-
dependently on front and surround speakers.
FM ANT A (NORM)/B (CATV) selector switch
Set to the A mode when using a connected FM antenna to listen
to non-cable FM broadcasts. Set to the B (CATV) mode when a
CATV cable is attached for listening to CATV (cable) FM broad-
casts. The B (CATV) mode is in effect when the B (CATV) in-
dicator lights. The initial mode will be memorized in the STATION
CALL switch.
In this way, by performing PRESET TUNING, you can tune into an
FM on-air station and a CATV station.
TV ANT (VIDEO/TV) selector switch
This switch can be used in place of the TV ANT switch on the RF
Modulator JA-RF5 (soid separately). This is effective only when
the JA-RF5’s TV ANT switch is set to the VIDEO position. For ex-
ample:
In VIDEO mode (TV indicator goes out):
Allows you to use video components connected to the receiver.
In TV mode (TV indicator lights):
Connects the TV antenna, thus allowing you to view normal TV
broadcasts, regardless of whether the receiver's POWER is ON or
OFF.
NOTE:
© When in the VIDEO mode, no sound will be produced from
the TV set's speakers. Listen using the speakers connected |
to the receiver.
© Noise may be produced if the TV set’s volume control is turn-
ed up. Turn down the set’s volurrie control when listening.
¢ This switch functions only when the TV ANT selector switch
on the RF Modulator is set to “VIDEO”.
STATION CALL RANDOM 20 CH switches
stations, together with the antenna A/B mode, FM AUTO/MONO
15
<ARB1030 >

FRONT PANEL FACILITIES
Only portions which differ significantly from the VSX-5000 are
described. The description of other portions is the same as that of the
VSX-5000, hence they are omitted.
Refer to the description of the VSX-5000 from Page 12. Note,
however, that portions marked ‘“VSX-5000 only’ are not in the
VSX-4000.
mxccv] ACOUSTIC
~ "e+
Eee TANOW Cali Banco soon SED
wit nn’
=e
s EE 1Ss Sess
VCR MODE STEREO/MONDO selector switch *
MONO: All playback, including stereo signals, aré produced in
monaural.
When the MODE MONDO indicator lights, the unit is set to the
MONO mode.
NOTE:
This switch can be used when one of the video system function
switches is selected. In addition, This switch can be preset for either
of VCR 1, VCR 2, or VDP/VCR 3. When any other function switch is
pressed, the MONO mode is automatically canceled.
VIDEO ENHANCER switch «
Press when performing video copying with added video enhancer
effects. When the switch is pressed, the monitored video image
will be the split screen picture.
VCR NOISE FILTER switch *
SIMULATED STEREO switch *
Press to produce a simulated stereo effect when listening to
monaural sources (for example normal AM or TV broadcasts).
By pressing this switch, ‘‘S/STEREO” appears on the display
panel.
NOTE: ;
° dn the case of the VSX-4000, S/S + S/W will be displayed
when SIMULATED STEREO and STEREO WIDE go ON
simultaneously.
STEREO WIDE switch (VSX-4000 only) *
Press to add an extra sense of breadth to stereo sources.
When surround speakers are connected, the surround effect is
produced.
By pressing this switch, “S/WIDE” will appear on the display
panel.
If tape hiss noise is noticeable when performing playback of video
cassette tapes, press this switch to reduce the noise.
By pressing this switch, ‘‘N FILTER’ will appear on the display
panel.
NOTE:
© This switch can be used when one of the video system -func-
tion switches is selected. In addition, this switch can be
preset for either of VCR 1, VCR 2, or VDP/VCR 3. When any
other audio function switch is pressed, the noise filter is
automatically canceled.
The effectiveness in reducing high-frequency hiss noise
varies depending on the type of tape used, the recording
level, and other conditions.
16
<ARB1030 >
ees

REMOTE CONTROL UNIT OPERATION
In addition to the present unit, the remote control unit can also
be used to operate other Pioneer components (TV, VCR, VDP
or CD) bearing the &] mark.
SLEEP key
Press to enable the sleep timer function. Each time you press
the key, the timer function becomes 60 minutes, 30 minutes,
or OFF, in that sequence.
When the SLEEP display is fully lit, this means 60 minutes,
when it is half lit, this means 30 minutes, and when it is out,
this means OFF.
RECEIVER power stand-by/on key A |
Audio/Video Function keys | =
==
MUTE key |-
SURROUND MODE key
FM/AM selecor keys
TV keys
VDP ... Sets the TV set function to VDP.
TV ... Sets the TV set function to TV.
— ... Reduces the TV set’s sound volume.
+ ,.. Increases the TV set’s sound volume.
PHONO keys
> (PLAY)... To begin record playback.
@ (STOP)... To stop record playback.
[ SURROUND MODE key sd
[When controlling the VSX-5000]
Selects the surround mode. Each time the key is pressed, the
function is switched in the following order:
. STUDIO --STADIUM~ DOLBY SURROUND — OFF :
[When controlling the VSX-4000]
Selects
the
SURROUND
mode.
Each
time
the
key
is
pressed, the function is switched in the following order:
SIMULATED
__
STEREO
__
niet?
ee
STEREO
WIDE
STEREO
WIDE
— OFF
VCR power key
Use to turn power ON/OFF to a VCR.
A/V selector switch
TV power key
Use to turn power ON/OFF to a TV.
VIDEO SELECTOR key
SURROUND VOLUME key
(functions only with the VSX-5000)
BALANCE key
MASTER VOLUME key
TUNER CH key
(When the A/V selector is A’)
The station which is memorized
in the STATION CALL switch
will be received.
+:By pressing this switch, the
channel number of the STA-
‘TION CALL switch will in-
crease.
-: By pressing this switch, the
channel number of the STA-
TION CALL switch will
decrease.
NOTE:
Unless the FM or AM function is
selected using the BAND selec-
_tor_keve.-vou--cannot-receive-.a-1-
tG?_-KEYS;-Y¥ OU CARROL FECOIVE--2
cA
broadcast.
TV CH key
(When the A/V selector is ‘’V’’)
+: Selects channels in ascen-
ding order.
—: Selects channels in descen-
ding order.
V7
<ARB1030 >

REMOTE CONTROL UNIT OPERATION
CD keys (When the A/V selector is ““A’’)
P| (Track search) ... When pressed once,
play advances to the beginning of the next
track; when pressed continuously, advances
to further tracks.
<4 (Track search) ... When pressed once,
play returns to the beginning of the currently
playing track; when pressed continuously,
returns to earlier tracks.
» (Play) ... Begins playback.
DISC SELECTOR ... Used to disc number
VDP (LaserVision player) keys
(When the A/V selector is ‘“V’’)
Pi (Scan) ... Scanning in forward direction
<4 (Scan) ... Scanning in reverse direction
> (Play) ... Switches the mode from stop
(disc not rotating) to normal
playback.
Returns the mode from pause,
still-frame, or multi-speed
playback to norma! playback.
SueeCTON A v
POWLAT STANG-SY/ON |
Starts chapter program
(1—6) for playback. playback.
gu
(Pause)
...
Press
to
temporarily
pause
wa
(Pause)
...
When
pressed,
picture
and
playback.
sound
vanish
and
playback
is
@
(Stop)
...
Press
to
stop
playback.
temporarily
interrupted.
Press again to release the
TAPE
keys
(When
the
A/V
selector
is
“A”’)
pause
mode.
;
mr
(FF)...
Winds
the
tape
quickly
from
@
(Stop)
...
Stops
playback.
¢:
left to tight. NOTE:
~#<
(REW)
...
Winds
the
tape
quickly
from
In
the
case
of
the
VDP,
the
#4
and
>|
symbols
right
to
left.
mean
manual
fast
feed.
You
cannot
perform
a
i)
(Mute)
...Press
to
eliminate
unwanted
chapter
search.
portions during recording, or
to create a non-recorded in-
terval between selections.
@ (REC)... Press to begin recording.
> (Play)... Press for forward-direction
_ tecording or playback.
<4 (Play)... Press for reverse-direction
recording or playback.
ua (Pause) ... Press to temporarily pause
recording or playback.
@ (Stop)... Press to stop tape travel and
recording.
VCR keys
(When the A/V selector is “’V’’)
® (FF) ... Advances the tape quickly.
<< (REW) ... Rewinds the tape quickly.
@ (REC) ... Begins recording.
> (Play) ... Begins playback.
um (Pause) ... Temporarily interrupts
playback or recording.
@ (Stop) ... Stops tape travel and recording.
NOTE:
The o and <4 keys do not function with VCR.
To control equipment other than this unit using the
remote control unit provided
@ Pioneer equipment bearing the mark which is provid-
ed
with
a
remote
sensor
can
be
operated
by
aiming
this
—
¢-
remote
contro!
unit
at
the
remote
sensor.
z
@
When
using
equipment
which
bears
the
mark
but
is
Even
when
using
these
connections,
if
a
remote
control
unit
is
not
provided
with
a
remote
sensor,
or
when
you
wish
to
provided
with
your
stereo
equipment,
you
can
operate
the
operate
only
the
receiver
by
aiming
the
remote
control
unit
remote
control
unit
by
facing
it
towards
the
remote
control
at
the
remote
sensor
of
the
receiver,
it
is
necessary
to
con-
sensor
on
the
receiver.
nect
the
receiver
to
the
REMOTE
CONTROL
IN/OUT
jack.
mers
(—
weor
Connect the receiver using a commercially available mini- (OY a ae
plug
type
cord.
s
sage
|
l
!
Connections for remote control
By connecting PIONEER stereo components to each other us-
ing the control input (CONTROL IN) jack on each component,
the entire system can be operated by a remote control unit.
Use the remote control cord which comes with the respective
unit for the connection. An example is shown in the drawing
below. So long as you connect “OUT” >”IN”, the connec-
OUTPUT
©
CONTROL
OUTPUT
CONTROL
ting
sequence
is
arbitrary.
In
the
case
of
a
unit
which
has
onl
TTT:
2
:
ey
.
.
Y
Feces
9
an
“IN”
connector,
however,
make
connection
to
it
last.
ee
.
CD
player
Turntable
18
<ARB1030 >

PREPARATIONS FOR BROADCAST RECEPTION
The following illustrations are all for the VSX-5000,
however the method of using the VSX-4000 is identical.
DIRECT ACCESS TUNING
When you know the frequency of the desired station, the fre-
quency can be input directly using the STATION CALL
(number) switches in the following way:
1 Press the POWER switch to the ON posi-
tion.
2 Select either FM or AM using the Band
Selector.
3 When listening to FM broadcasts, use the
FM ANT switch to select the type of
broadcast.
¢To receive CATV FM broadcasts, press the switch so
that the B (CATV) indicator lights.
¢ This switch has no effect on the reception of AM broad-
casts.
4 Press the DIRECT ACCESS switch.
5 Input the desired station frequency using
the STATION CALL switches.
Example 1: To receive FM 106.00 MHz
[Display] DIRECT
ACCESS we)
[STATION CALL
switch]
FM IN ae
eM iN id. os
i 6/16
BM
iN
db.
sf
@ When the CHANNEL STEP switch is set to FM 100 kHz,
the tuning operation is completed and reception begins.
10/20
PM 106.0 es 0
¢ When the CHANNEL STEP switch is set to FM 50 kHz:
After. completing input of the station frequency, the receiver
detects whether the input frequency is within receivable fre-
quency range; if it is within this range, the characters “IN”
disappear, and reception begins.
G Adjust the sound volume and tone as
desired.
To cancel input:
e During the about ten seconds that the “IN” indicator is
lighted, do not press any of the STATION CALL switches
(1—10[0]).
¢ During the time the “IN” indicator is lighted, press the
DIRECT ACCESS switch.
Notes regarding FM or AM direct access tun-
ing
© When the CHANNEL STEP switch is set to the AM 10 kHz
position, there is no need to input the last digit ‘0’ of the
desired station frequency. Depending on the station fre-
quency, inputting the first two or three digits is sufficient.
If you input the incorrect frequency:
® When frequency numbers are input, the receiver judges
whether the first digit input is correct; incorrect inputs will
not be accepted. Acceptable first digit inputs:
FM: 1, 8, 9, AM: 1, 5, 6, 7, 8, 9
e If a frequency outside the receiver's range (FM 87.5
MHz—108 MHz; AM 530 kHz—1,600 kHz or 531
kHz—1,602 kHz) is input, the display will indicate
“ERROR,” and reception will return to the frequency
received previously to the input.
19
<ARB1030>

PREPARATIONS FOR BROADCAST RECEPTION
AUTO OR MANUAL TUNING For Manual Tuning:
i
ez, CRBS EGEATE
Se ee
Se a on ee PAS =
© Soogo Momo ss Sessa
1 2
AUTO tuning:
Auto tuning is convenient when you do not remember the fre-
quency of a desired station, or when you wish to find stations
that you do not normally listen to.
MANUAL tuning:
This is the ‘‘normal’’ tuning mode. Each time the TUNING
switch “ +" or “~” is pressed, the tuning frequency changes
by one step, allowing you to find stations manually. 6
1 Press the POWER switch to the ON posi-
tion.
2 Use the BAND selector to choose either
FM or AM.
3 When listening to FM broadcasts, use the
FM ANT switch to select the reception
mode.
®To receive CATV (cable) FM broadcasts, press the
switch so that the B (CATV) indicator lights.
¢ This switch has no effect on AM reception.
For AUTO Tuning: :
4 Set the AUTO/MANUAL switch to the
auto tuning mode.
¢ in the Auto Tuning mode, the TUNING AUTO indicator
will light. The word ““AUTO” will appear on the display
panel for several seconds.
B Press the “+” or “—" side of the TUNING
switch.
© By pressing the “+” side, scanning will take place in
the direction of increasing frequency. By pressing the
(—) side, scanning will take place in the direction of
decreasing frequency.
¢When-a-station-is-received;-scanning-wi ip fo)
wish to receive a different station, press the TUNIN
switch (“+” or “’—"") again.
20
<ARB1030 >
4 Set the AUTO/MANUAL switch to the
manual tuning mode.
© When in the Manual Tuning mode, the TUNING AUTO
indicator will go out. The word “MANU” will appear on
the display panel for several seconds.
Press the “+” or “—" side of the TUNING
switch as necessary to set to the frequen-
cy of the desired station.
Each time the switch is pressed, the tun-
ing frequency will change by one step in
the direction corresponding to the side
pressed. When pressed continuously, the
reception frequency will also change con-
tinuously.
When a station is received, the TUNED indicator will
light.
¢ When the received station is broadcasting a program in
FM stereo, the STEREO indicator will light.
Adjust the sound volume and tone as
desired.
NOTE:
When Auto Tuning is used, correct reception may not be
possible for very distant stations or stations with very weak
signals. In this event, Manual Tuning is recommended.
¢ The TUNED indicator may not light with broadcasts received
over long distances, or when the broadcast signals are ex-
tremely weak.