Pipeline Pro 2 Plus User manual

PIPELINE-PRO.CO.UK
PIPELINE PRO 2 PLUS MANUAL
02 FEATURES
01 PIPELINE PRO 2 PLUS
03 MAIN MENU
The PIPELINE PRO 2 PLUS is a German made high-end mod for use
with 18650 batteries and has 5 different modes.
Variable Watt, Temperature Control (with various wires possible),
Variable Watt with Heat Protection, Variable Watt with Power Boost
and Bypass (unregulated, electronic overload protection).
We recommend operation with high current carrying IMR and high
drain batteries (eg Samsung 25R) with a discharge current of 20
amps (unprotected).
For optimal function of the temperature control we recommend
the Dicodes wire Resistherm (NiFe30).
-5 to 40 Watts
-Adjustable Centre Pin
-Up to 12V output voltage
-Up to 15A output current
-OLED display
-Temperature controlled vaping (possible with various wires)
-Heat Protection Function
-Power Boost Function
-Unregulated vaping possible
(‘Bypass’ electronic overload protection)
-Battery shutdown voltage adjustable from 2.5V to 3.0V
-Resistance check
-Displays battery voltage under load
-Adjustable brightness display
-Set the length of time the menu is displayed
-Set the standby time
-Personalise click setting from 0-5 to activate device
-Info menu
-Battery capacity measurable
-Atomizer resistance range from 0.05Ω to 5Ω is possible
-Atomizer resistance from 0.2Ω to 3.5Ω (40W)
-Reverse polarity protection
-Abnormal temperature protection
-Serial Number
-2 year warranty on the electronics
-Design by Thomas Wilms
-Made in Germany by Dicodes
Click once to enter the menu. There you can navigate by clicking
through the menu items. After a short wait at the desired menu item
you will be able to change the values by further clicking.
Power Up and Power Down
(Change Power)
Power Up gradually increases the power up to the set power limit
Power Down decreases the power.
Factory setting 10W
The power limit value is set in the extended functions submenu
‘Temp Menu’ and provides a power limit for less powerful atomizers
or a desired power limit.

03 MAIN MENU
Temperature Up and Temperature Down
(Temperature Adjustment)
These menu items are visible only when the temperature control
is enabled (see Mode menu).
The menu items allow you to set the maximum temperature for tem-
perature controlled vaping in 5 ° C increments from 120 ° C to 280 °
C (or 250 ° F - 540 ° F). For precise control you need the atomizer to
be at room temperature (about 20 ° C) Calibration (Calibr). For this
purpose a suitable wire with a high temperature coefficient is nee-
ded. Enter the temperature coefficient of the wire in the Extended
Functions submenu> Temp menu> Temp Cof.
Factory setting: 190 ° C
Mode
The PIPELINE PRO 2 PLUS provides 5 different modes
that can be selected in this menu
Power (VW), TmpCtrl (Temperature-Controlled vaping), PowerHP (VW
with Heat Protection activated), PowerBO (VW with Power Boost acti-
vated), and Bypass (unregulated mode, electronic overload protec-
tion). You can disable the „Expert Mode“ in the extended functions
menu (> System menu) PowerHP, PowerBO and Bypass disable.
If you select temperature controlled vaping (TmpCtrl), after
2 seconds the display will show „Wire320“ on the top line.
There you can choose a suitable wire for temperature controlled
vaping. 320 stands for the set temperature coefficient of the wire.
This varies on the top line according to the type of wire selected.
Choose from the following types of wire:
If you select „Other“, you must manually enter the temperature
coefficient of the wire in the extended functions menu (>Temp
Menu>Temp Cof).
Factory setting: Power
Switching Off the PIPELINE PRO 2 PLUS
In addition to the auto-shutdown the user can turn off the power
manually. We recommend the unit is switched off before changing
the battery, only then are the statistics stored, otherwise the changes
since the last save will be lost by removing the battery.
Extended Functions Menu
The „Extended Functions“ menu has 3 sub-menus:
- Temp Menu> Settings for the coil
- System Menu> Settings to customize the PIPELINE PRO 2 PLUS
- Info Menu> Statistical display
Calibration
(Manual Coil Temperature Calibration)
These menu items are visible only when the temperature control is
enabled (see Mode menu). The calibration measures the coil
resistance as a reference value for the temperature control, this
should only be done at room temperature (20 ° C). The calibration
is a process with 3 steps: Init, Confirm and Process. Each of these 3
steps must be confirmed by pressing the button, so that the
calibration is actually executed. We recommend heating the coil to
the “evaporation phase“ a second time to calibrate , since the
resistance of the wire may vary.
Coil resistance and temperature
In this menu item, the resistance (R) of the coil is shown.
The display ranges from 0.0Ω to 9.90Ω.
When temperature controlled vaping is enabled,
the actual temperature of the heating coil is also displayed (T).
Battery Status
The „Battery Status“ shows the battery voltage with low current drain
(Bat) and the battery voltage under load of the atomizer used (BatL).
If the difference between the two values shows a strong drop in the
voltage this is an indication of a low battery or contact problems.
Stainless Steel Wire
Other WireTungsten Wire
Titanium Wire
Nickel Wire Ni200
Resistherm Wire

04 EXTENDED FUNCTIONS MENU
Bat Min:
Setting the cut off voltage of
the battery (2.5 to 3.0V - Factory
setting: 2.7V)
Cycles:
Number of puffs since
resetting the counter
Temp Cof up:
increasing the wire-temperature
coefficient (default: 320) *
Temp Cof down:
Decreasing the
wire-temperature coefficient
(default: 320) *
Power Lim:
Set the power limit. The intensity
of „Power Boost“ is also defined
by setting the Power Limit
(factory setting: 40W)
HP Set:
Heat Protection mode selected
(More information at
06 - Factory setting: 6)
Power Boost:
Power Boost mode selected
(More information at
06 - Factory setting: 3)
Lumen:
Changes the brightness of the
display. 1 is the darkest value, 6
the brightest. (Default: 4)
Time:
Vaping time in H: MM: SS
since resetting the counter
SwOff Time:
Automatic shutdown of the device
after a given time. When setting
the switch off time, the value in
the display appears in „minutes“.
(Factory setting: 5 minutes)
Energy:
Energy consumption since
resetting the counter
On Click:
Sets the number of clicks to
activate a switched off device.
(Factory setting: 0 - Ready for
vaping)
BatCap:
Capacity of consumed battery
since reset (Capacity of the
battery if synchronized with the
replacement of the battery)
Reset Cntr:
Reset the counter
TotCycl:
Total amount of puffs
on PIPELINE PRO 2 PLUS
(not resettable)
TotTime:
Total vaping time of
PIPELINE PRO 2 PLUS
(not resettable)
* The temperature coefficient of the wire
material used for correct operation in the range
100-650: 320 = Dicodes wire (Resistherm),
620 = nickel, approximately 105 = Stainless Steel,
350 = titanium,
480 = tungsten (value = coefficient * 10E + 5K)
MenuOn Click:
Sets the number of clicks
needed to display the menu.
(Factory setting: 1
Click Speed:
Key velocity
(Animation appears at 4 and 5)
(Factory setting: 3)
Half Watt:
Power increment 1W / 0.5W
(<20W), 2W / 1W (20-40W)
(factory setting 1)
Temp Unit:
Unit of temperature display
in ° C or ° F (Default ° C)
Display Mode:
When (1) is selected the display shows during vaping and for 4 seconds after.
When (0) is selected the display shows the most recently calculated figures for
4 seconds after vaping but remains off during vaping. (Factory setting is 1).
Display Dir:
Display orientation for right or
left hand (default: R)
Expert Mode:
Unlock (1) or Disable (0) the HP,
BO and bypass modes
(factory setting: 1)
Reset:
Reset to factory settings

06 ERROR CODES
Battery Voltage Too High Power Boost:
Atomizer not found
Error In temperature calibration
Short due to bad connection or
overload from high voltage
Battery Voltage Too Low
Overheating
Maximum vape time exceeded
Overload caused by high current (re-
sistance too low for the selected power)
Keep the button pressed to acknowledge the error.
HP-Set:
Overload caused by high voltage to
the atomizer (resistance too high for the
voltage supplied)
07 HEAT PROTECTION AND POWER BOOST SETTINGS
08 HEAT PROTECTION AND POWER BOOST SETTINGS
„Heat Protection“ prevents overheating of the heating coil.
This preserves the flavour of liquids, even at higher watt settings.
Here you can select 10 different settings:Time in ms,
Power factor = On-time / (on-time + off-time).
Index On Off Power Factor
01 400 100 0,80
02 600 100 0,86
03 800 110 0,88
04 1000 120 0,89
05 1350 150 0,90
06 2000 200 0,91
07 2000 180 0,92
08 2000 150 0,93
09 2000 100 0,95
10 2000 80 0,96
The factory setting is „06“
Accelerated heating of the coil.The intensity of boost can be defined
under „Power Limit“.Here you can select 10 different settings:
Index Boost time in ms Nominal output in ms
00 - -
01 300 -
02 450 -
03 600 -
04 50 500
05 80 600
06 120 700
07 160 800
08 200 900
09 250 1000
10 300 1000
The PIPELINE PRO 2 PLUS features a graphical
OLED display showing all important information.
In temperature controlled mode
displays the temperature at the
end of vape. In all other modes
displays the battery voltage
(under load)
Power Display
In Direct-Mode (Bypass)
it shows the actual power
applied to the coil
The battery symbol indicates
the remaining battery power .
Atomizer resistance including
the increase due to higher
temperature .
05 DISPLAY OPERATION
09 BASICS OF TEMPERATURE CONTROLLED VAPING
Temperature controlled vaping is a complex issue. We would like
to try to explain to you some important basics in order to avoid
problems.
Why temperature controlled vaping?
The food flavourings contained in e-Liquids develop different
flavours at different temperatures. You can imagine it as cold or
lukewarm cola. The taste will vary depending on the
temperature of the beverage.

Dry Hit
A „Dry Hit“ refers to bad or nonexistent liquid flow to the heating coil
which will cause a very unpleasant taste.
Wire types
The thickness of the wire determines how quickly the coil reaches
the set temperature. You can compensate for the deficiency of a
sluggish coil with higher power, but this also increases the power
consumption.
Also you will require different wire for different types of atomizer
for example a Dripper has a different process. Changing your wick
material often will require a firmer wire. The Dicodes wire Resistherm
NiFe30 is much more stable than the well known temperature-
controlled vaping nickel wire Ni200.
The PIPELINE PRO 2 PLUS can use any wire with a high temperature
coefficient by adjusting the
temperature coefficient.
Please do not forget to enter it in the extended functions menu
(Temp Menu> Temp COF).
Temperature control
Depending on the setting will determine a temperature control or a
temperature limit.
If the power is set low with good liquid flow but does not reach the
selected temperature, the PIPELINE PRO 2 PLUS limits the temperature
to avoid a dry hit. If the power is set high and the selected
temperature is reached, the PIPELINE PRO 2 PLUS adjusts power to
maintain a stable temperature.
Care must be taken when inserting the battery into the
PIPELINE PRO 2 PLUS. Hold the device at a slight angle and carefully
insert the battery (positive terminal first).
You have purchased from us a battery / a battery-powered product.
The battery will provide you with long service and when it reaches
the end of its life it must be disposed of responsibly.
Batteries cannot be disposed of in household waste and must be
taken to a recycling point, alternatively you can return the battery to:
PIPELINE-UK LTD,
19 Watergate Street, Chester,
CH1 2LB.
Batteries contain valuable raw materials that can be recycled.
The environment and PIPELINE say thank you.
WEEE Reg no. DE10791500
Electronic cigarettes are not „healthy“, but they are less harmful
than regular cigarettes. Electronic cigarettes are an alternative to
cigarettes and not suitable for smoking cessation.
Electronic cigarettes are not suitable for children under the age of
18, non-smokers, people with allergies to nicotine and propylene
glycol, pregnant or breastfeeding women and people with
cardiovascular diseases. Our products are not for sale to, or use by
anyone under the age of 18 years!
WWW.PIPELINE-STORE.COM
10 NOTES
BATTERY RECYCLING
09 BASICS OF TEMPERATURE CONTROLLED VAPING
It is now also known that high temperatures may cause undesirable
side effects.
With a functioning temperature controlled setup dry hits are
effectively excluded. So you can use an atomizer without a window
to the last drop of liquid.
To use the temperature control, you need an atomizer with a
heating wire, which has a high temperature coefficient
(we recommend the Dicodes wire Resistherm NiFe30).
Due to the high temperature coefficient, the resistance of the wire is
increased as soon as the coil is heated. It is necessary for the
atomizer to be at room temperature to calibrate, so that on the basis
of resistance changes the PIPELINE PRO 2 PLUS can determine the
temperature of the heating coil.
Please ensure that the wraps of the coil do not touch and the
contacts of the 510 port and within the atomizer used are clean.
Corrosion or contamination of a contact area can lead to low
resistance variations, which are then erroneously interpreted by the
electronics as temperature changes. Therefore, all contacts should
be cleaned regularly with alcohol.
With the PIPELINE PRO 2 PLUS you can find the optimum temperature
and thus the optimum flavour.
TERMS
Temperature Coefficient
This value describes how much the resistance of the
heating wire changes with increasing or decreasing temperature.
Calibration
During calibration, the zero point of the measurement is accurately
determined. As with a speedometer in a car, when at rest it must
show 0 mph. If the calibration is not carefully carried out a reliable
measurement of the temperature is impossible.
The PIPELINE PRO 2 PLUS has automatic or manual calibration.
We recommend calibrating the coil manually. It is important that the
atomizer is at room temperature at the time of calibration (eg. 20 ° C).
We recommend heating the coil to the “evaporation phase“ a
second time to calibrate, since the resistance of the wire may vary.
Caution: When auto-calibrating, make sure to wait a few minutes
before changing the battery so that the atomizer cools.