FUFU & GAGA Shoe Storage Cabinet User manual

Version:12/15/2022 1/21
Shoe Storage Cabinet

2/21
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

3/21
3.5 x 30 mm
6 x 28 mm 8 x 40 mm
200 mm
15 x 9.5 mm
3.5 x 12 mm
3.5 x 20 mm
3.5 x 14 mm
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
J1
J2
G1
G2
A x 36 C x 8
B x 36 F x 8 G x 5
H x 50 J x 2
I x 16 K x 6 L x 3
M x 3 O x 6
N x 6 P x 6 Q x 4
R x 2 T x 2
S x 2 U x 18

4/21
x6
x3
x3
x2
x2
x2
x2
1
2
3
4
5
6
7
7
7
8
8
9
10
11
12
13
14
16
17
18
19
15

5/21
STEP1: Extend Slide
Extender la diapositiva
Extendre la diapositive
STEP2: Push lever UP
Empujar hacia arriba
Lever le levier
STEP3: Remove Runner
Quitar el corredor
Enlever le coureur

H
Knock part(P) and (O) into corresponding
holes in plate 1 and 2 as shown.
Screw quickfit screw(A) into corresponding
holes in plate 1 and 2 with a screwdriver as
shown.
Fix slide rail(J1) to plate 1 and 2 respectively
using screw(H) as shown.
6/21
A x 20 O x 6 P x 6 J1 x 1 H x 4
6 x 28 mm 3 x 14 mm
1
H
P
P
P
P
P
P
A
P
O
O
O
O
O
O
O
AA
AA
AA
AA
A
A
AA
AA
AA
AA
AA
1
1
2
2
H
J1
H
H
J1
H
H

Screw quickfit screw(A) into plate 4 as shown.
Attach plate 5 to plate 4, put cam lock(B) into
holes in plate 5 and turn clockwise to tighten
at first.
FIx slide rail(J1) to two sides of plate 5 using
screw(H) as shown.
3 x 14 mm
B x 2 J1 x 1 H x 4
2
A x 2
6 x 28 mm
7/21
A
A
A
4
4
5
4
H
H
H
H
H
H
BB
J1
J1
B
H
H
H

Slide plate 8 along grooves in plate 4,8 and 9
at first.
Insert wooden dowel(C) into plate 4 as shown.
Connect plate 1 and 2 with plate 4,8,9 and 10,
put cam lock(B) into holes in plate 4,8,9,10
and turn clockwise to tighten at first.
B
B
B
B
BB
15 x 9.5 mm 8 x 40 mm
C x 4B x 20
3
8/21
7
7
7
6
4
B
B
B
BBBB
B
B
B
C
CB
B
B
4
C
C
CC
B
1
2
B
8
10
9
8

Screw quickfit screw(A) into corresponding
holes in plate 3 as shown.
Cover plate 3 to the top with wooden dow-
el(C), put cam lock(B) into holes in plate 1,4,2
and turn clockwise to tighten as shown.
6 x 28 mm 15 x 9.5 mm 8 x 40 mm
B x 6 C x 4A x 6
4
9/21
7
7
7
4
A
A
A
A
A
A
3
3
B
B
B
B
B
B
C
C
C
C
1
2
8
810
9
A
3
C
B
C

3.5 x 14 mm 3.5 x 20 mm
H x 16 R x 2 T x 2I x 16
Reinforce back plate using part(I) and screw(H) as shown.
Fix part(R) to plate 1 and 2 respectively using screw(T) as shown.
5
10/21
I
H
7
7
H
H
H
I
H
I
H
H
I
H
I
H
H
H
H
H
H
H
H
H
I
I
I
I
I
I
I
I
I
I
I
I
R
R
T
T
R
T
2
3