Pittsburgh 63656 User manual

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
63656
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 17h
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2017 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
To ols required for assembly and se rv ic e m ay n ot b e i nc lu de d .
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2For technical questions, please call 1-888-866-5797.Item 63656
Specifications
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
Use Precautions
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions.
Keep work area well lighted.
3. Store idle equipment. When not in use, the Dial
Indicator must be stored in a dry location. Always
lock up products and keep out of reach of children.
4. Use the right product for the job. There
are certain applications for which the Dial
Indicator was designed. Do not modify the Dial
Indicator and do not use the Dial Indicator for
a purpose for which it was not intended.
5. Check for damaged parts. Before using any
product, any part that appears damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check
for any broken or damaged parts and any other
conditions that may affect its operation. Replace
or repair damaged or worn parts immediately.
6. Replacement parts and accessories. When
servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
7. Do not allow children to play with the Dial Indicator.

Page 3For technical questions, please call 1-888-866-5797.Item 63656
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Note: Because of the unique Flexible
Stand, your Dial Indicator can by mounted to many
different locations for different apllications. When
mounting the Dial Indicator, take into account the
location of the test material, the length of the Dial
Indicator, and the design of the test fixture.
1. Secure pliers to any location.
2. Loosen Caliper Clamp (4) and insert the Dial Caliper
(1) into the opening. See Parts Diagram. Tighten
the knob into place to secure the Dial Caliper.
3. Turn the Cam Lock (5) to lock the cable in place. If
the Cam Lock does not tighten down properly, adjust
the fine-tuning mechanism located near the Dial.
4. Establish a base line. Turn the Bezel on the
Dial so that the needle points to zero.
Note: There are many applications for the Dial
Indicator with Flex Stand and Clamp. Following
is one example of how the Dial Indicator can
be used: Testing brake rotors for warp.
5. Following Steps 1 through 4, set the Pin of the Dial
lightly against a rotor to establish a base line. You
do not want the needle too tight against the object
being measured. There must be room for the
needle to move in and out while under pressure.
6. Spin the rotor to see if it is true. As the rotor spins,
the needle will move in and out. The dial will
indicate the degrees of difference in true, defined
as the measurements which are above and below
the base line established at the beginning.
Note: Dial Indicators are highly versatile tools used
in many applications in machine shops and precision
fabricating and testing facilities. The above example is
only one of many possible uses for this measuring tool.
Parts List and Diagram
Part Description Qty
1 Dial Caliper 1
2 Locking Cable 1
3 Pliers 1
4 Caliper Clamp 1
5 Cam Lock 1

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797