Pivot Dual Gauge PRO User manual

1
(DPB-M As of September, 2020 No.3)
Easy Installation
•Do not work in areas where there is excessive exhaust.
Due to vehicle exhaust emission poisoning or fire may result in a damage to
humans.
•Do not crush the cable.
Please be careful that the cable does not get crushed by the seat rail or car
door steel plate, nor cut by any sharp steel plate as this may cause a poor
connection or an electric short leading to fire or other danger.
•Do not operate while driving.
Operating or checking the display during driving may cause an accident;
please use with the utmost consideration for safety.
•Please securely fasten the product to a stable place and be
sure to store bundle away all wires with tape, etc...
It is very dangerous to pull tangled wires by force or allow tangled wires to
interfere with driving.
•This product is for DC12V cars;
Installation cannot be carried out on cars with other voltage batteries.
•Just after installation do not exert any strong force on the product.
When double-sided tape is used for an installation be warned that when hot the tape
temporarily losses adhesiveness.
•Do Not Use Chemical Cleansers.
If the unit gets dirty please wipe with a soft cloth to remove any dirt. Do not use chemical
cleansers such as thinner, benzene, or alcohol.
•Do not install the product in any place subject to high temperature or
any place where water may be splashed.
•Make sure to replace all screws and parts to their original place.
•Do not install the product in a place where it will cause distraction.
•Do not, in any manner, process, take apart, or make changes to this
product.
WARNING Improper use or disregard of these warnings
may result in the injury or death of people. CAUTION Improper use or disregard of these warnings may cause injury to persons, damage the product and other things.
USER’S MANUAL
Contents
Product ＋
If this product is given to
another user, make sure to
include this User’s Manual.
Thank you for purchasing this PIVOT product.
Please read this manual carefully and keep it for future
reference.
Features
Unit Gauge Cable
User’s
Manual
(This Book)
Please check the contents of the package
Zip Ties
(Large) × 2
(Small) × 5
Cut
Connectors
× 2
Meter Meter Holder
Allen
Wrench
Double-sided
Tape
Cushion
Tape
OBD Cable
with Fuse 3A
IGN Cable
with Fuse 3A
BOOST＋DIGITAL DPB-M
Designed for MAZDA SKYACTIV-D
Contents/ WARNING / CAUTION ……… 1
Features …………………………………… 1
Part Names and Display ………………… 2
Connecting The Wires …………………… 2
Installing The Product …………………… 3
Basic Operation …………………………… 3
Switching The Display …………………… 4
Illumination color settings ………………… 4
Illumination brightness settings ………… 4
Troubleshooting …………………………… 4
Our specialized communication analyzer makes it possible to display BOOST data of MAZDA SKYACTIV-D.
Dual Display
2-Color Illumination Switch with 3-step Dimmer
Meter Holderincluded
Easy Installation
Black Titanium Bezel
High quality black titanium bezel.
The included full cover type holder allows seamless installation to a number
of places.
Peak Hold
Save and display each peak reading after engine starts.
Illumination switch allows selection between two colors and brightness
adjusted with three-step dimmer.
Simple coupler connection to Diagnostic monitor connector.
1. The display will not be proper if the ECU being used is not the standard one or if a sub-computer is being used, even
in compatible car models.
2.Cannot be used in combination with other company’s products that use Diagnostic Monitoring Connectors.
3. For details about using combinations of PIVOT OBD products, see here. ⇒ http://pivotjp.com/obd/
A-Pillar
Stand
Screw Nut
Indicator needle and digital display provide easy viewing of
multi-data.

2
START
ENGINE
STOP
Notes about using the OBD Connector
If you unable to get a grip
on the distended portions.
Make sure to grip the
distended portions when
pulling it out or inserting it. Do not pull on the wires
when trying to remove the
connector; the wires may
become disconnected.
CAUTION
With some car models it
may be difficult to get a
good grip on the connector.
In such case, pull
out the connector
by pulling on the
end of the zip tie.
The meter start-up and stop is differ in power connection method.
Unplug the connector of Yellow and Red cable of OBD Cable and
connect Yellow cable of IGN Cable into the connector on Yellow cable,
then connect to IGN cable to IGN of car. (Do not connect to Acc)
IGN Cable
＝Cut Connector
IGN
(12V with Key Switch ON)
OBD Cable Diagnostic
Monitoring
Connector
Yellow Yellow
Red
Linked to the ECU Linked to the key switch
Normal IGN (using IGN Cable)(not using IGN Cable)
1
Part Names and Display
Connecting The Wires
Analog Display
Analog Display
Display Boost data.
2Needle Shows the current values and peak value.
3Switch
Display switches between types.
4Digital Display
Digital Display
Use to change modes of digital display
and reset the peak value.
Unit
4-pin
Connector
Meter
Holder
6-pin
Connector
5-pin
Connector
Engine Start.
Insert the OBD Connector to the Diagnostic Monitoring
Connector.
Insert the 4-pin Connector to the backside of the meter.
Insert the 5-pin Connector of Gauge Cable and 6-pin
Connector from the Power Cable to the Unit.
5Illumination
(night illumination)
6Display Range
Red
Normally illuminated when on display
and Three-step dimming.
Dial & Needle : White or Blue
Analog Display
Digital Display
Backside
of the
meter Diagnostic
Monitoring
Connector
MAZDA
At the right foot of the driver seat
At the left foot of the driver seat
Panel to right of steering wheel
(upper part of small storage box)
Placement Diagram for Diagnostic
Monitoring Connector
1
2
3
4
[ Meter ]
Boost [0–200kPa]
(Switchable)
Water Temp [
-
35–150 °C]
Voltage [8–18 V ]
Oil Temp [
-
35–150 °C]
[ Unit ] (View from Gauge Connection) (View from Car Connection)
7
10
Meter connector Connect gauge cable
8
Spare No need to use
9
Power connector Connect OBD cable
7 8 9 10
Size [Unit：
mm]
ø60
15 30
70
50
Depth22
Unit
Meter
ø65
(1.5 m) (0.5 m)
Engine
Start
110 mm
2
10 mm
345
How to use the Cut Connectors
When crimping, please
use crimpers or use
pliers to bend and then
solder together.
Peel off of the vinyl
cover at connection.
Peel off of the vinyl
cover at the end of
the product’s wire.
Wrap around both
wire coils.
Close tightly with cut
connector.
Insulate with vinyl
tape.
1
2
3
4
4

3
3.Affix the Cushion Tape to the base of the meter, connect the Gauge Cable to the
Meter, and install the Meter into the Meter Holder. Please add the Cushion Tape
if the Meter not fixed.
1.Fasten using the
double-sided tape.
Note : Please be sure about
where you wish to install the
meter, as it is not advisable to
reuse double-sided tape.
Meter Holder
GaugeCable
Back side
of Meter
Clean
to remove
oil and dust
Double-sided
tape
2.After deciding the position
and angle of the meter face,
fasten the Hexagonal bolt
on both sides to secure.
Connector
Cushion Tape Cushion Tape
Cushion Tape
Hexagonal bolt
A Installation with the Meter Holder
Installing The Product
Installing The Meter
14523
Basic Operation
Display Each Mode Meter OFF
Engine Start Opening Demo Engine Stop
The needle stops
in the vicinity of
lowest value.
Unit Zip tie
(Large)
Through
holes
Thick cable
or pipe
When Fastenings to
a Cable or Pipe
(Example of Installation)
Double-sided
tape
Clean to
remove
oil and dust.
Fastening
to Flat Space
On the back side
of the under cover
Under the steering
column cover
Do not install into low positions
Installing The Unit
As shown in the below diagram , fasten the unit
into positions not usually affected by water.
On the inside of
the driver’s door
Gauge
Cable
Cut the Cushion Tape in half, affix to base of the Meter to be on press
fit condition with adjusting number. And connect the Gauge Cable to
the Meter and insert into the panel.
Cushion Tape
Cushion Tape
B Installation to panel or something C Installation to A-pillar using A-pillar Stand
Panel
Cut the Cushion
Tape in half
Make a ø5 hole on the place to install the meter of the A-pillar, and fix the
Meter using A-pillar Stand with Screw and Nut.
A-pillar
Screw
Nut
A-pillar
Stand
ø5 Hole
A-pillar
•When the engine starts, the needle will move to the extreme left several
times for searching position. Then it will move to the maximum value
and finally to reading for current measurement item.
•Due to analyzation time for the car data transmission it may take up to a
few seconds from engine start before opening demo.
Opening
Demo
•Due to analyzation time for the car data transmission, the
illumination may remain on for up to 1 minutes even after
the engine has been turned off; this is normal and no
effect on the vehicle performance. (except wiring IGN)
Turning off
the Display

4PIVOT CORPORATION 87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 JAPAN
+START
ENGINE
STOP
Troubleshooting
Because after changing displays, if the car’s engine is turned off within 3 seconds, the new setting will
not be stored, make sure to wait at least 3 seconds before turning the engine off.
Please reconfirm whether wiring and connections
are correct or not.
Please reconfirm the Fitting List.
Upon starting up, the unit will not start in the
newly changed display.
Poor connection of Gauge cable ,
6-pin Connector or OBD Connector wires.
Trouble Possible Causes Possible Solutions
Does not work with Engine start.
Illumination brightness settings
The unit has been installed into an incompatible
car model.
Before the opening demo starts the needle briefly
moves.
This is due to a special characteristic of the meter and is not a malfunction.
The displayed values are different from the standard
meter.
Due to the ECU information received, the displayed values on this product may differ from those of
standard or other meters.
Adjustment in case of anxious about reflected illumination of door mirror
or something
[ c-1 = White, c-2 = Blue ]
1234
56
Press
the switch
for 6 seconds
Press the switch
to change the brightness
(e.g. L- 3 )
Release the switch
after displayed
the current setting
Release
the switch
after setting is done
Back to normal display with
no operation for 5 seconds
Illumination color settings
Each pressing will change the color
12 34
5
Display the current
illumination color setting
Press the
switch to change
the color
(e.g. c-1)
Release the switch
after displayed
the current setting
Release the switch
after setting is done
Setting Completed
Back to normal display with
no operation for 5 seconds
After the meter off,
Engine start during
pressing the switch
Engine Start
Switching The Display
Switching The Digital Display
Display and Reset the Peak Value
Water Temp Oil TempVoltage
(Lighting)
(Lighting)
(Lighting) (Blinking)
(Blinking)
(Blinking)
(decimal point
is lightning)
Real-time Display Peak Value Display
Reset the Peak Value
Only the peak value on display will be
reset. This will return to the Real-time
Display for the currently displayed mode.
Press
Switch
Press
Switch
Water Temperature / Oil Temperature
Reading the Display
for 3Secondsfor 3Seconds
With no operation
5Seconds
•Peak readings are reset when the key is turned OFF.
•For Boost, Water Temperature and Oil Temperature the high will be shown and for Voltage the low
will be displayed.
•If you wish to check the loss of voltage upon operation of the starter, turn the key to the ON position
and after the digital display comes on, operate the starter.
Press switch to change
the multi-digital display
in operation
Display a peak value after
3 seconds and the current
brightness after 6 seconds
Holding downs the switch
in operation
Each pressing will change the brightness
Setting Completed
(High)(Mid)(Low)
The first place on the
below shows “
-
” (minus).
The third place from the
below shows “c”(Celsius).
Numerical Value
Only.
[-
35–
-
1°C ][ 0–99 °C ] [ 100–150°C ]
• Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
• We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar designs, regulating characteristics,
circuitry and circuitry layout.
• We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’s Manual.
(Note)