Planar Invitium Tk7 User manual

Invitium
™
Medical Workstation
Tk7 and Tn4
QUICK SETUP GUIDE
www.planar.com

2 Invitium Quick Setup Guide
Standard Equipment
Optional Equipment
Related documentation
•Invitium Specification Sheet – Provides computer and display specifications
for models Tn4 and Tk7. Refer to the Invitium documentation kit or
www.planar.com to obtain this sheet.
•Invitium Tk7 and Tn4 Operations Manual – Provides detailed instructions
on how to set up, use, clean, and troubleshoot the system. Download the
manual from www. planar.com.
▲Tk7 only
▲USB or PS/2

Invitium Quick Setup Guide 3
Attach the Mounting Fixture
1 Install the mounting fixture. (Refer to the vendor documentation.)
2 Attach the Invitium to the fixture using the VESA panel on the back
of the Invitium.
•If the VESA panel on the fixture has slotted upper screw holes, secure the top
two screws to the Invitium’s VESA panel, and then slide the Invitium onto
the fixture.
•If the holes are not slotted, have another person support the Invitium against
the fixture while you secure the screws.

4 Invitium Quick Setup Guide
3 Tighten the top two screws through the fixture’s mounting plate.
4 Insert and tighten the bottom two screws through the mounting plate.

Invitium Quick Setup Guide 5
Open the Clamshell
1 Tilt or rotate the Invitium away from the mounting fixture to allow the clamshell
to open fully.
Note Accessing the connector bay differs depending on the mounting fixture.
2 Loosen the screws on the portion of the clamshell located below the VESA
mounting plate on the Invitium.
3 Open the clamshell.

6 Invitium Quick Setup Guide
Connect the Cables
1 Connect the keyboard, mouse, and other peripherals.
Caution – Electrical hazard
PC audio is connected through the video/audio cable. Do not
disconnect the video/audio cable or connect another display to
this port.
Power
ports
COM
ports
Antenna
Video/
audio USB
ports
Microphone
input
Ethernet PC audio
(line) input
Keyboard
1
2
3
4
PC card
slots
Wireless
PC card

Invitium Quick Setup Guide 7
2 Install the PCMCIA wireless network card, if appropriate.
•Slide the network card into the PC card slot until it locks into place.
•Attach the gold connectors on the antenna to the two pinholes on the
protruding side of the card. NOTE: The Antenna has been tested with the
CISCO AIRONET 350 SERIES card and registered with the FCC.
Warning – Personal injury
While installing and operating this transmitter and antenna
combination the radio frequency exposure limit of 1mW/cm2
may be exceeded at distance close to the antennas installed.
Therefore, the user must maintain a minimum distance of 20cm
from the antenna at all times.

8 Invitium Quick Setup Guide
3 Connect the power adapter.
Align the pins on the DC connector with the holes in the power port and push
the connector until it locks into place.
Caution – Hardware damage
Do not force the connector into the power port. The pins may
bend if they do not align with the holes.
click!
4 Close the clamshell and fasten the screws.

Invitium Quick Setup Guide 9
Start the Invitium
Press the power switch to the on (|) position.
Adjust the display
•Brightness – Press the + or – control to adjust display brightness.
•Display power – Press the display power button to toggle power on or off.
•Keyboard light – Place the keyboard directly under the light. Press the
keyboard light to brighten the keyboard during night use. The light turns off
after 30 minutes.
Brightness Keyboard light
Power switch
Display power Keyboard light