Planar PS5562 User manual

Planar PS Series RS232
User Guide
PS4662T
PS5562
PS5562T
PS6562

Copyright © 26 Jan 2017 by Planar Systems, Inc. All rights reserved.
Contents of this publication may not be reproduced in any form without permission of Planar
Systems, Inc.
Trademark Credits
Windows™ is a trademark of Microsoft Corp.
All other companies are trademarks or registered trademarks of their respective companies.
Disclaimer
The information contained in this document is subject to change without notice. Planar
Systems, Inc. makes no warranty of any kind with regard to this material. While every
precaution has been taken in the preparation of this manual, the Company shall not be liable
for errors or omissions contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Warranty and Service Plans
Planar warranty and service plans will help you maximize your investment by providing great
support, display uptime, and performance optimization. From post-sale technical support to
a full suite of depot services, our services are performed by trained Planar employees. When
you purchase a Planar product, you get more than a display, you get the service and support
you need to maximize your investment. To find the latest warranty and service information
regarding your Planar product, please visit http://www.planar.com/support
Part Number: 020-1329-00A

Planar PS Series RS232 User Guide 1
RS232 Codes
RS232 control is not necessary for operation, but is a convenient way to control
displays from a computer at a distance. Most things you can do with the remote, you
can do with RS232 commands. Plus, you can send inquiries to the displays and find
out the current settings and values.
1RS232 Command Format
STX(1byte) + IDT(1byte)+ Type(1byte)+ CMD(3bytes)+ [Value/Reply(1byte)] +
ETX(1byte)
STX: Start byte = 07
IDT: Don’t care
Type: Read or Write command, 01: read, 02: write; 00: return to host (from
monitor)
CMD: As shown in the table on the following pages
Value: Setting Value of “Write Command”
Reply: Return Value of monitor
ETX: End byte = 08
Transmit from PC (Host)
Read command: 07 IDT 01 CMD 08 (7bytes)
Write/Setting command: 07 IDT 02 CMD VAL 08 (8bytes)
Return from Monitor: Sent after receiving any valid command. The response CMD is
the same as the received CMD.
2Serial Port Setting
Baud rate can be set to 115200, 38400, 19200, or 9600 to match the monitor baud
rate setting.
Baud rate 19200 is the default setting.
Explanation of symbols
▲: Valid command in standby mode.
Note: The Wake Up from Sleep setting must be set to Wake on All for these commands to
work in standby.
Baud Rate Data Bit Parity Bit Stop Bit
19200 8 None 1

RS232 Codes
2 Planar PS Series RS232 User Guide
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark
Power Control
and Input
Source
Power Control POW R/W 00 Off (soft power) 50 4F 57 ▲
01 On (soft power) ▲
Input Source MIN R/W 00 VGA 4D 49 4E
13 DisplayPort
9HDMI1
10 HDMI2
Display
Adjustment
Color BRI R/W 0~100 Backlight Brightness 42 52 49
BRL R/W 0~100 Digital Brightness Level 42 52 4C
BLC R/W 00 Off (Backlight) 42 4C 43
01 On (Backlight)
CON R/W 0~100 Contrast 43 4F 4E
SHA R/W 0~8 Sharpness 53 48 41
HUE R/W 0~100 Hue 48 55 45
SAT R/W 0~100 Saturation 53 41 54
Scheme SCM R/W 00 User 53 43 4D
01 Sport
02 Game
03 Cinema
04 Vivid

RS232 Codes
Planar PS Series RS232 User Guide 3
Display
Adjustment
Color
Temperature
COT R/W 00 User 43 4F 54
01 6500K
02 9300K
03 3200K
06 5000K
07 7500K
Gamma GAC R/W 00 Off (Gamma) 47 41 43
01 1.85 (Gamma)
02 1.9 (Gamma)
03 1.95 (Gamma)
04 2.0 (Gamma)
05 2.05 (Gamma)
06 2.15 (Gamma)
07 2.15 (Gamma)
08 2.2 (Gamma)
09 2.25 (Gamma)
10 2.3 (Gamma)
11 2.35 (Gamma)
12 2.4 (Gamma)
13 2.45 (Gamma)
14 2.5 (Gamma)
15 2.55 (Gamma)
16 2.6 (Gamma)
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
4 Planar PS Series RS232 User Guide
Display
Adjustment
Gain & Offset USR R/W 0~100 Red Gain (0~100) 55 53 52
USG R/W 0~100 Green Gain (0~100) 55 53 47
USB R/W 0~100 Blue Gain (0~100) 55 53 42
UOR R/W 0~100 Red Offset (0~100) 55 4F 52
UOG R/W 0~100 Green Offset (0~100) 55 4F 47
UOB R/W 0~100 Blue Offset (0~100) 55 4F 42
VGA
Adjustment
PHA R/W 0~63 Phase 50 48 41
CLO R/W 0~100 Clock 43 4C 4F
HOR R/W 0~100 Horizontal Position 48 4F 52
VER R/W 0~100 Vertical Position 56 45 52
ADJ W00 Auto Adjust 41 44 4A
RTC Current Time
Adjustment
RTY R/W 0~99 Year 52 54 59
RTM R/W 1~12 Month 52 54 4D
RTD R/W 1~31 Day 52 54 44
RTH R/W 0~23 Hour 52 54 48
RTN R/W 0~59 Minute 52 54 4E
Timer Mode TMS R/W 0Everyday Mode 54 4D 53
1Workday Mode
2User Mode
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
Planar PS Series RS232 User Guide 5
RTC Enable AEN R/W 0~127 In User Mode:
Set bit0 to 1: Sunday
Enable
Set bit1 to 1: Monday
Enable
Set bit2 to 1: Tuesday
Enable
Set bit3 to 1:
Wednesday Enable
Set bit4 to 1: Thursday
Enable
Set bit5 to 1: Friday
Enable
Set bit6 to 1: Saturday
Enable
In Everyday Mode:
Set any bit0~6 to 1:
Mon.~Sun. Enable
In Workday Mode:
Set bit0 to 1: Sunday
Enable
Set any bit1~5 to 1:
Mon.~Fri. Enable
Set bit6 to 1: Saturday
Enable
41 45 4E
Disable AEF R/W 0~127 In User Mode:
Set bit0 to 1: Sunday
Disable
Set bit1 to 1: Monday
Disable
Set bit2 to 1: Tuesday
Disable
Set bit3 to 1:
Wednesday Disable
Set bit4 to 1: Thursday
Disable
Set bit5 to 1: Friday
Disable
Set bit6 to 1: Saturday
Disable
In Everyday Mode:
Set any bit0~6 to 1:
Mon.~Sun. Disable
In Workday Mode:
Set bit0 to 1: Sunday
Disable
Set any bit1~5 to 1:
Mon.~Fri. Disable
Set bit6 to 1: Saturday
Disable
41 45 46
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
6 Planar PS Series RS232 User Guide
RTC Sunday SNH R/W 0~23 Sunday On Hour 49 4E 48
SNM R/W 0~59 Sunday On Minute 53 4E 4D
SFH R/W 0~23 Sunday Off Hour 53 46 48
SFM R/W 0~59 Sunday Off Minute 53 46 4D
Monday NNH R/W 0~23 Monday On Hour 4E 4E 48
NNM R/W 0~59 Monday On Minute 4E 4E 4D
NFH R/W 0~23 Monday Off Hour 4E 46 48
NFM R/W 0~59 Monday Off Minute 4E 46 4D
Tuesday ENH R/W 0~23 Tuesday On Hour 45 4E 48
ENM R/W 0~59 Tuesday On Minute 45 4E 4D
EFH R/W 0~23 Tuesday Off Hour 45 46 48
EFM R/W 0~59 Tuesday Off Minute 45 46 4D
Wednesday DNH R/W 0~23 Wednesday On Hour 44 4E 48
DNM R/W 0~59 Wednesday On Minute 44 4E 4D
DFH R/W 0~23 Wednesday Off Hour 44 46 48
DFM R/W 0~59 Wednesday Off Minute 44 46 4D
Thursday UNH R/W 0~23 Thursday On Hour 55 4E 48
UNM R/W 0~59 Thursday On Minute 55 4E 4D
UFH R/W 0~23 Thursday Off Hour 55 46 48
UFM R/W 0~59 Thursday Off Minute 55 46 4D
Friday INH R/W 0~23 Friday On Hour 49 4E 48
INM R/W 0~59 Friday On Minute 49 4E 4D
IFH R/W 0~23 Friday Off Hour 49 46 48
IFM R/W 0~59 Friday Off Minute 49 46 4D
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
Planar PS Series RS232 User Guide 7
RTC Saturday TNH R/W 0~23 Saturday On Hour 54 4E 48
TNM R/W 0~59 Saturday On Minute 54 4E 4D
TFH R/W 0~23 Saturday Off Hour 54 46 48
TFM R/W 0~59 Saturday Off Minute 54 46 4D
Audio Volume VOL R/W 0~100 volume 56 4F 4C
Bass BAS R/W 0~12 Bass (-6 ~ 6) 42 41 53
Treble TRE R/W 0~12 Treble (-6 ~ 6) 54 52 45
Balance BAL R/W 0~12 Balance (-6 ~ 6) 42 41 4C
Internal
Speaker
INS R/W 00 Internal Speaker Off 49 4E 53
01 Internal Speaker On
Mute MUT R/W 00 Mute Off 4D 55 54
01 Mute On
OSD Transparency OST R/W 0~12 OSD Transparency 4F 53 54
H Position OSH R/W 0~100 OSD H Position 4F 53 48
V Position OSV R/W 0~100 OSD V Position 4F 53 56
OSD Rotation OSR R/W 00 Landscape 4F 53 52
01 Portrait
OSD Language OSL R/W 00 English 4F 53 4C
01 Chinese
OSD Timeout OSO R/W 5~120 OSD Timeout. The value
increments by five (5, 10,
15, 20..., 115, 120 seconds).
4F 43 4F
Splash Screen SPS R/W 0Off 53 50 53
1On
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
8 Planar PS Series RS232 User Guide
OSD Message Box MSB R/W 0Off 4D 53 42
1On
Other Control Scaling ASP R/W 01 16:9 41 53 50
02 4:3
04 Auto
ZOM R/W 0~10 Adjust overscan ratio 41 53 50
Baud Rate
Adjustment
BRA R/W 00 115200 42 52 41
01 38400
02 19200
03 9600
Power Saving
Config
WFS R/W 0Wake on VGA 57 46 53
1Wake on All
2Never Sleep
Auto Scan ATS R/W 0Off 41 54 53
1Main
Pixel Orbit IRF R/W 0Off 49 52 46
1On
Smart Light
Control
SLC R/W 0Off 53 4C 43
1DCR
2Light Sensor
Power LED LED R/W 0Off 4C 45 44
1On
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
Planar PS Series RS232 User Guide 9
Other Control HDMI RGB
Color Range
HCR R/W 00 Auto Detect 48 43 52
01 Full Range
02 Limited Range
Remote
Control
RCU W14 MENU Key 52 43 55
04 INFO Key
02 UP Key
25 DOWN Key
01 LEFT Key
03 RIGHT Key
18 ENTER Key
05 EXIT Key
07 VGA Key
09 HDMI1 Key
12 HDMI2 Key
08 DISPLAYPORT Key
15 SOURCE Key
20 SCALING Key 52 43 55
00 MUTE Key
23 BRIGHT Key
24 CONTRAST Key
30 AUTO Key
29 VOLUME+ Key
27 VOLUME- Key
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
10 Planar PS Series RS232 User Guide
Other Control Remote
Control
ALL W00 Reset all 41 4C 4C
01 Reset all but
communications (RS232
and LAN)
KLC R/W 00 Un-lock keys 4B 4C 43
01 Lock keys
SER RRead Serial Number 53 45 52
MNA RRead Model Name 4D 4E 41
GVE RRead Firmware Version 47 56 45
RTV RRead RS232 table Version 52 54 56
GVS W 0 Querying main scaler
version
47 56 53
1Querying sub mcu version
2Querying network module
version
Ethernet
Setup
Network
Enable
NWE R/W 0No 4E 57 45
1Yes
Dynamic IP DIP R/W 0Disable 44 49 50
1Enable
Default LDS W 0 Load default settings
(About 15 seconds.)
4C 44 53
E-Mail Alert PSA R/W 0Off (Power Status Alert) 50 53 41
1On (Power Status Alert)
SSA R/W 0Off (Source Status Alert) 53 53 41
1On (Source Status Alert)
SLA R/W 0Off (Signal Lost Alert) 53 4C 41
1On (Signal Lost Alert)
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

RS232 Codes
Planar PS Series RS232 User Guide 11
Ethernet Setup Static IP
Settings
IP1 R/W 0~255 Static IP Address 1 49 50 31
IP2 R/W 0~255 Static IP Address 2 49 50 32
IP3 R/W 0~255 Static IP Address 3 49 50 33
IP4 R/W 0~255 Static IP Address 4 49 50 34
MK1 R/W 0~255 Subnet Mask 1 4D 4B 31
MK2 R/W 0~255 Subnet Mask 2 4D 4B 32
MK3 R/W 0~255 Subnet Mask 3 4D 4B 33
MK4 R/W 0~255 Subnet Mask 4 4D 4B 34
GW1 R/W 0~255 Gateway 1 47 57 31
GW2 R/W 0~255 Gateway 2 47 57 32
GW3 R/W 0~255 Gateway 3 47 57 33
GW4 R/W 0~255 Gateway 4 47 57 34
FD1 R/W 0~255 DNS Address 1 46 44 31
FD2 R/W 0~255 DNS Address 2 46 44 32
FD3 R/W 0~255 DNS Address 3 46 44 33
FD4 R/W 0~255 DNS Address 4 46 44 34
SNS W 0 Save Static IP Settings 53 4E 53
MAC W0~5 Querying MAC ID #0~#5 4D 41 43
Main Item Control Item CMD Type
Value /
Reply
(Decimal)
Content CMD (HEX) Remark

Example
12 Planar PS Series RS232 User Guide
Example
Power Control and Input Source
Turn monitor power off [CMD: POW]
[Transmit] : PC →07 01 02 50 4F 57 00 08 →Monitor
[Return] : Monitor →07 01 00 50 4F 57 00 08 →PC
Turn monitor power on [CMD: POW]
[Transmit] : PC →07 01 02 50 4F 57 01 08 →Monitor
[Return] : Monitor →07 01 00 50 4F 57 01 08 →PC
Read Power Status from monitor [CMD: POW]
[Transmit] : PC →07 01 01 50 4F 57 08 →Monitor
[Return] : Monitor →07 01 00 50 4F 57 XX 08 →PC
XX = 0, the set is off. XX = 1, the set is on.
Display Adjustment
Read back light from monitor [CMD: BRI] (If the setting of back light is 80)
[Transmit] : PC →07 0101 42 52 49 08 →Monitor
[Return] : Monitor →07 01 00 42 52 49 50 08 →PC
Set back light 80 to monitor [CMD: BRI]
[Transmit] : PC →07 01 02 42 52 49 50 08 →Monitor
[Return] : Monitor →07 01 00 42 52 49 50 08 →PC
Set Contrast 30 to monitor [CMD: CON]
[Transmit] : PC →07 01 02 43 4F 4E 1E 08 →Monitor
[Return] : Monitor →07 01 00 43 4F 4E 1E 08 →PC
Read Contrast from monitor [CMD: CON] (If the monitor contrast setting is 50)
[Transmit] : PC →07 0101 43 4F 4E 08 →Monitor
[Return] : Monitor →07 01 00 43 4F 4E 32 08 →Monitor

Scaling Adjustment
Planar PS Series RS232 User Guide 13
Scaling Adjustment
Set monitor to 4:3 [CMD: ASP]
[Transmit] : PC →07 01 02 41 53 50 02 08 →Monitor
[Return] : Monitor →07 01 00 41 53 50 02 08 →PC
Other Control
Adjust up to monitor [CMD: RCU]
[Transmit] : PC →07 01 02 52 43 55 02 08 →Monitor
[Return] : Monitor →07 01 00 52 43 55 02 08 →PC
Reset all to monitor [CMD: ALL]
[Transmit] : PC →07 01 02 41 4C 4C 00 08 →Monitor
[Return] : Monitor →07 01 00 41 4C 4C 00 08 →PC
Read serial number monitor [CMD: SER]
[Transmit] : PC →07 01 01 53 45 52 08 →Monitor
[Return] : Monitor →07 01 00 53 45 52 S(0) … S(12) 08 →PC , S(0) ~ S(12): serial
number in ASCII
Read firmware version monitor [CMD: GVE]
[Transmit] : PC →07 01 01 47 56 45 08 →Monitor
[Return] : Monitor →07 01 00 47 56 45 S(0) … S(5) 08 →PC , S(0) ~ S(5): firmware
version in ASCII

Planar PS Series RS232 User Guide 14
Accessing Planar’s
Technical Support
Website
Go to www.planar.com/support to locate the following support documents and
resources:
• User Guide
• RS232 User Manual
• Touchscreen drivers
• Standard warranties
• Planar support hotline number and email