Planet Audio PI9764B User manual

1. Before Operation
1.1 Glossary
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0
format used for the playback control. For the discs containing PBC, It can
playback interactive software with the menu displayed on monitor screen.
If the disc contain still images, it can playback high definition of still images.
Title
Generally, the title is the important part of DVD disc. for example, the
theme part of movie is title 1, the part described how to make movie is title
2, the cast is title 3, etc. Every title contain a serial number that is easy to
look up.
Chapter
A title can be divided into several blocks, so that every block can be operated
as a unit, the unit is called chapter. The chapter contain a unit at least.
Track
It is the biggest component of VCD. Generally, every song of the disc
is a track.
1.2 Precautions
Safety
1. Power Source: The unit should be connected to power supply only of
the type described in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is
connected to the vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
Environment
1. Do not use this unit near water and moisture.
2. If moisture forms inside the Lens, it may not operate properly. To correct
this problem, wait until the moisture is evaporated.
3. If the car interior is extremely hot, do not use the player until the car has
been cool off .

1.5 Remote Control Description
16. SEARCH BUTTON
17. RDM BUTTON
18. RPT BUTTON
19. SUBTITLE/REDIAL BUTTON
20. TITLE/PBC/PAIR BUTTON
21. VIEW-ANGLE/ST/# BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
25. A-B BUTTON
26. INT BUTTON
27. EQ/OPEN BUTTON
28. LOC/SLOW-FWD/* BUTTON
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
33. OK BUTTON
34. VOLUME+ BUTTON
35. BAND BUTTON
36. PROG BUTTON
37. OSD BUTTON
38. LOUD BUTTON
39. TEL BUTTON
40. TA BUTTON
41. AF BUTTON
1. ANG BUTTON
2. DVD MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
5. >>| BUTTON
6. > BUTTON
7. |<< BUTTON
8. v BUTTON
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
11. NUMBER(0~10,+10
-10) BUTTONS
12. 10+/PTY BUTTON
13. SETUP BUTTON
14. MODE BUTTON
15. APS/Hang Up BUTTON
1
2
3
4
5
6
7
98
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
40
41
39
36
37 38
1.3 Maintenance and Cleaning of Discs
Disc Maintenance
1. To keep the disc clean, handle the disc by its edge, do not touch the disc
surface of the play side.
2. Do not stick paper or tape on the disc. If there is anything on the disc surface,
wipe it up with a soft cloth before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as
caliduct, or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
4. Put the disc inside disc case to keep temperature after finishing playback.
Disc Cleaning
1. Before playing, wipe the disc with a clean cloth. wipe the disc outwards from
the disc center.
2. Do not use petrol, thinner. Commercial cleaner or anti-static spray to wipe
disc.
1.4 Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating
sheet out of the remote control as the direction indicated by the
arrow.(see fig.1)
2.Press the movable block hold as the direction indicated by the A arrow
(See fig.2), then pull the battery holder out of the remote control as
the direction indicated by the B arrow(see fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward.
(See fig.3).
4.Insert the battery holder to the original position in remote control.
(See fig.3).
Note about the Battery of the Remote Control:
1.Improper use of battery may cause overheating or explosion.
2.Battery leakage may cause damage to the remote control(Battery
Life: 6 months with normal use in normal room temperature).
3.Do not short the battery.
4.Do not throw the battery into the fire.
5.To avoid the risk of accident, keep the battery out of reach of children.
Fig.1 Fig.2 Fig.3
A
B
+ side up
correct
correct
wrong

1.6 Locations and Names of Controls on or in the unit
Front Panel
The Front Facet after removing front panel
7 16
SD/MMC
1
2
3 4
6
10
9 8
11 12 14
5
13 15
17
1. OPEN button
2. POWER/MUTE button
3. Monitor
4. AUX IN socket
5. Disc Slot
6. USB Jack
7. SD/MMC Card Slot
8. EJECT button
9. VOL knob
10. BAND/TEL button
11.APS/HANG UP button
12. MODE/1-6 button
13. >>| button
14. |<< button
15. REL button
16. RESET button
17. Small LCD screen
X
PI9764B
1.7 Connection Description
Description of the Wiring Diagram for Socket 1
1. Parking wire must be connected. And the parking brake must be engaged in order for the monitor to work.
2. Use the clip end of the Ground Wire provided by manufacturer to connect Mounting Screw, using the other
end of the Ground Wire to connect the negative pole of the power source. Otherwise, the video on screen
maybe flashes.
Description of Wires Connection
Description of Connecting the Parking Brake Line to the Parking Brake System Built in a Car
Parking brake
Parking brake switch
(inside the car)
Parking brake wire(Green)
To metallic body or chassis of the car
NOTE: after connecting the Parking Line, the video on the small monitor of the front panel will be display only after braking the car.
Description of the Wiring Diagram for Socket 2
YELLOW
MEMORY B+
BLACK(GND)
IGNITION SWITCH
BLUE AUTO ANT
GREEN
SUBWOOFER OUTPUT
RED
FRONT
REAR
RIGHT
SP
FRONT WHITE
WHITE / BLACK
GREEN / BLACK VIOLET / BLACK
GRAY / BLACK
GRAY
VIOLETGREEN
REAR
LEFT
SP
+
++
+
RED (R)
WHITE (L)
FRONT OUTPUT
FUSED
FILTER
BOX 1A
& 10 A
FUSES
WIRING CONNECTING SOCKET 1
WIRING CONNECTING PLUG 1
NOTES:
1. Only speakers with 4 ohms impedance may be used.
2. Ensure that the blue auto antenna cable does not make contact
with any ground connection.
BLACK
ISO CONNECTOR
PARKING BRAKE
GREEN
REVERSAL INPUT
WHITE
Mounting Bolt
Wiring Connecting Socket 2
Wiring Connecting Socket 1
Radio Antenna jack
BLACK
BLACK
BLACK
AV IN
Media Device Cable
USB
BLACK
KEY GROUND(BLACK)
KEY A(BROWN)
KEY B(YELLOW)
GREY
YELLOW
YELLOW
VIDEO OUTPUT
REAR VIEW CAMERA
BLACK
YELLOW
REAR OUTPUT
GREY
WHITE (L)
RED (R)
WIRING CONNECTING SOCKET 2
WIRING CONNECTING PLUG 2
BROWN
RED (R)
WHITE (L)
YELLOW VIDEO

1.8 UNIT INSTALLATION
Rear View Camera
INSTALLATION INSTRUCTIONS
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL S TRAP ON TH E M ETAL
CONNECTED TO THE BOTTOM
BRACKET OF THE CAR.
METAL STRAP
DASH BOARD
SLIDING METAL HOUSING
TO DRAW THE CHASSIS OUT OF
THE SLIDING METAL HOUSING,
INSERT THE LEFT AND RIGHT KEY
PLATES INTO THE RIGHT POSITION
OF THE 2 SIDES OF CHASSIS.
PLASTIC TRIM OUT
UNIT CHASSIS
SELECT THE PROPER TAB
FOR FIXING THE SLIDING
METAL HOUSING.
THE UNIT IS INSTALLED TO BE AN ANTI-THEFT ONE. THE CHASSIS
OF THE UNIT WEARS A SLIDING METAL HOUSING. PLEASE DO THE
CONNECTION OF THE POWER, SPEAKERS AND ANTENNA ACCORDING
TO THE REQUIREMENT OF THE INSTRUCTION BOOK , THEN INSTALL
THE SLIDING METAL HOUSING IN THE CAR AS FOLLOWS.
FRONT PANEL
In any running mode, the video signal will switch to camera mode (if applicable)when car is in reverse.
After taking the car out of reverse, it will resume to its previous mode.
Analog on-site backup Analog on-site backup
PIC
ANGLE
Warning:
Always check the surrounding environment. Objects might be reversed. The rear view
camera is designed only to assist while reversing. Due to the limitations of the camera
angle and range, it may cause accidents if the driver relies solely on the reverse camera
and display.
2. Common Operation
1. To turn on/off the unit
In power off mode, short press the POWER button to turn on the unit.
In power on mode, long press the POWER button on the front panel or short
press the POWER button on the remote control to turn off the unit.
2. To slide the monitor of the Car Audio System out of/into the chassis
Pressing the OPEN button can slide the monitor of the Car Audio System out
of the chassis or slide it into the chassis.
3. To select an optimal angle of the monitor of the Car Audio System
To select an up-down optimal angle of the monitor of the Car Audio System,
press the DOWN/UP button on the monitor or ANG button on the remote control
repeatedly.
4. To select function mode
Press the MODE button to select RADIO, DISC
(After inserting a disc), USB(After inserting a USB
storage), CARD(After inserting a card), AV IN,
BLUETOOTH or Media mode.
During playback, tapping the icon after popping
up Keyboard interface can pop up Mode Menu as
right. then tap one icon in it to select your desired mode.
Note: This unit has front and rear USB. Only one will work at a time.
5. To adjust sound level
Rotate the VOL knob on the front panel or press or hold the + or - button on the
remote control to directly adjust the volume level.
6. To mute sound
Press the MUTE button on the remote control to turn on/off MUTE mode.
pressing the POWER button on the front panel shortly also can turn on/off MUTE
mode.
7. To display clock time
Press the CLK button to display clock time on the small monitor of the front panel.
After sliding the monitor into the chassis, pressing the CLK button can display
clock time on the small LCD.
8. To select a desired EQ mode
Press the EQ button on the remote control to select one of the preset music
equalizer curves: POP, ROCK, CLAS, FLAT. The sound effect will be changed.
9. To turn on/off LOUD mode
Press the LOUD button to turn on/off LOUD mode.
When turning on LOUD mode, it will enhance bass level immediately when bass
is not enough.
10.To remove the front panel and reset the player
When the monitor or the small LCD display wrongly or some buttons are not
available or sound is distorted, press the REL button on the front panel to detach
the front panel and then pull it rightward and then leftward to remove it, then
press the RESET button to rehabilitate the distorted program to zero.
Mode Menu

11.To do setup
To do setup, tap the icon in the Main Menu to turn to
SETUP interface as right.
In the interface, select one of GENERAL, TIME, AUDIO,
VIDEO ,RADIO , STEERING WHEEL CONTROL,
CALIBRATE by tapping them, then set them by tapping
some icons on the right side accordingly.
STEERING WHEEL CONTROL: press one button on the
steering wheel then the LCD will show KEY 1 setting, select
the function (such as vol control ,seeking, mute ,power
etc)and then tap it to confirm. It can support mostly 6
shortcut keys. Press reset can cancel all the setting
. AUDIO: Tap the icon to pop up the AUDIO setup interface
as right. you can adjust the Subwoofer VOL here.
Note: In radio mode, the password is 888888.
3. Radio Operation
1. Enter RADIO mode
When you use MODE button or Mode Menu to enter RADIO
mode, it will display RADIO interface as right.
In RADIO interface, tapping the icon can enter Mode
Menu; during playback ,tapping the icon can
turn to frequency interface as right; the other icons are
same as ones in the unit panel or in the Remote Control.
In menu set interface, you can adjust MUTE, APS, EQ,
TA, AF, PTY as right.
2. BAND BUTTON
In RADIO mode, press the BAND button on the remote
control to select your desired radio band of FM1, FM2, FM3,
AM1 and AM2, and the word means which band is selected
will be displayed on the small monitor of the front panel.
3. TUNE/SEEK UP/DOWN BUTTONS
1) Press and hold the >>|/|<< button to automatically search
up/down for an available station from current frequency.
2) Briefly press the >>| / |<< button to manually search up or down with step by step for your
desired station from the current frequency.
4. APS BUTTON
1)When pressing and holding the APS button,the radio searches from the lowest frequency
and checks the signal strength level until 1 cycle search is finished. And then the 6 strongest
stations are preset to the corresponding preset number memory bank. The AS operation is
implemented in the each bank of the selected band. When the AS operation is finished, it
will scan each preset station for 5 seconds in FM or AM band from M1 as briefly pressing
APS button. After finishing a circle of scanning , it will resume broadcasting on the M1.
(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button, the radio will scan each preset station for 5
seconds in FM or AM band from M1. After finishing a circle of scanning, it will resume
broadcasting on the M1.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time; In AM band, AM1, AM2 is
checked one at a time.
RADIO interface
GENERAL SETUP
RADIO interface
5. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current band, press and hold any one
of the six preset buttons (1-6) on remote control .
2) To recall the preset memory on the current band, press one of the preset buttons
[1-6] on remote control or long press the MODE button on the front panel repeatly.
6. STEREO/MONO BUTTON
Press the ST button on the remote control to select the STEREO or MONO sound
mode for FM band.
7. LOC BUTTON
1) In RADIO mode, when the signals of the distant radio stations are very weak and
the receiving effect is bad during tuning, check whether there is the word LOC on
LCD. If there is the word LOC on LCD, press this button to turn off the LOC
function, then tune again for the distance radio station;
2) In RADIO mode, when the signals of the local radio stations are too strong this
causes interference to the receiving effect during tuning, press this button to turn
on the LOC function to display the word LOC on LCD, then tune again for the local
radio station.
8. PTY (PROGRAM TYPE) BUTTON
Press the PTY button briefly to select one of the following modes:
PTY MUSIC group- - PTY SPEECH group -- OFF
When PTY group is on, press the VOL+ or VOL- button on the remote control or
rotate the VOL knob on the front panel to select one of PTY programs as follows:
<-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-->EDUCATE<-->DRAMA
<-->CULTURE<-->SCIENCE<--> VARIED<-->WEATHER<--> FINANCE
<-->CHILDREN<-->SOCIAL<-->RELIGION<-->PHONE IN<-->TRAVEL
<-->LEISURE<-->DOCUMENT< -->PTY NONE<-->ALARM< -->POP M
< -->ROCK M<-->EASY M<-->LIGHT M<--> CLASSICS<-->OTHER M
<-->JAZZ<-->COUNTRY<-->NATION M<-->OLDIES<-->FOLK M<-->
When PTY group is on, pressing the 6 number buttons also can select one of PTY
programs as above.
After selecting one of the PTY programs, it will display SEEK PTY and
automatically search for the station of the PTY program. If the station of the PTY
program does not exist, it will display PTY NONE and then return back to the
normal station.
9. AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressing the AF button briefly,the AF switching mode is selected and the AF
switching mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.

When the AF switching mode is selected, the radio checks the signal strength of the
AF all the time. The interval of checking time of each AFs depends on the signal
strength of the current station, from a few minute for the strong station to a few
seconds for the weak station. Every time that a new AF is stronger than the current
station, it switches over to that frequency for very short time, and the
NEW FREQUENCY is displayed for 1-2 second.
Because the mute time of the AF switching or the checking time is very short, it is
almost inaudible in case of normal program. (When AF flash on LCD, it will search
for the stronger RDS station. If AF and TP flash on LCD, it can only search for the
traffic announcement station).
In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save the RDS program.
10. TA [TRAFFIC ANNOUNCEMENT] BUTTON
Press the TA button shortly to turn on TA search mode.
When traffic announcement is transmitted:
1) If the unit is in Disc Play mode, it will switch to radio mode temporarily.
2) Temporarily switch over to an EON linked station when EON detects a traffic
announcement on that other program, and TA, TP will be displayed on LCD
* TA interruption function:
The current traffic announcement is cancelled by pressing TA button shortly.
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved
only when traffic program identification code has been received.
4. Media Device Operation
1. Enter Media mode
When inserting the plug into your device , it will
automatically switch modes and display the menu on
touch screen as right.
You can also use MODE button or Mode Menu to enter
the model.
2. Play audio files
: Tap it can pause playback:
: Tap it can stop playback.
: Tap one of them can switch on between the speed
levels of fast backward or forward.
: Tap one of them can select next or previous track.
: Tap it to turn volume up and down.
: Tap it to change the audio and video playback.
Media menu
USB/CARD INTERFACE
3. Display control icons
When displaying playback, tap icon to turn
to control icons as right.
Tapping the direction icon to select the play
function such as : PLAYLISTS, ARTISTS,
ALBUMS, GENRES, SONGS,
COMPOSERS, REPEAT and so on.
4. Play video files
During audio playback, tap this icon to turn to
video playback.
: Tap one of them to select the track or
chapter in your library, after that, tap the
OK to confirm and play your selection.
: After selecting, tap it to play your selection.
Note: This device only support video files from
certain device due to the software limitation on your device.
This unit may support certain video files from iPod, but can not
support videos from iPhone.
5. Disc, USB and CARD Operation
5.1 Load/unload disc, USB or CARD
To play files in a disc or card, press the EJECT button to slide down the monitor .
Then insert the disc or card into the disc slot or SD/MMC Card slot.
To unload the disc or card, press the STOP button twice to stop playback, then
press the EJECT button to slide down the monitor and eject disc in the disc slot
and then remove the disc; or push the card firstly and pull it out of the card slot.
To play files in an USB, insert the USB into the USB jack connecting to the Rear
cabinet.
To unload the USB, press the STOP button twice and then remove the USB .
In USB or CARD mode, select your desired as right.
Remark: the icon is for audio files; the icon is
for video files; the icon is for image files.
Tap the icon to turn to main menu, tap the icon
to turn to previous setting.
VIDEO mode
Control icons
*

: Tap it to pause playback
: Tap it to stop playback .
:Tapping one of them can switch on between
the speed levels of fast backward or forward.
(Except image mode.)
: Tapping one of them can select next or
previous chapter/track.
: Tap it to turn volume up and down.
: Tap it to turn the selecting page up and down.
: Tap it to select INT play mode(Except image mode.)
: During VCD playback, tap it to select the audio
ST/MONO .
: Same as the MENU button on the remote control.
: Same as the TITLE button on the remote control.
: Same as the REPEAT button on the remote control.
: Same as the SUBTITLE button on the remote control.
: Tap it to select the track from 1-9 and then select
OK to play your selecting.
: During playback, press the ZOOM button
and then tap one of them are same as the direction
buttons on the Remote Control.
(Except music & image mode.);
During playback, press one of them to change the
playback angle.
(Only for image mode.)
: Same as the ZOOM button on the Remote Control.
: Same as the RDM button on the Remote Control.
: During DVD playback, tap the icon to change the
playback angle.
Root interface for MUSIC
Keyboard interface-1
Keyboard interface-2
Keyboard interface-3
5.2 Pause Playback
When playing DVD/VCD/CD/MP3/WMA , press the PAUSE button on IR
remote control to pause the playback, press the PLAY button to resume
normal playback.
5.3 Stop Playback
When playing DVD/VCD/MP3/WMA/CD , press the STOP button once to
pause the playback, then press the PLAY button to resume the normal
playback; press the STOP button twice to full stop the playback, then press
the PLAY button to start playing from the beginning of the first chapter/track.
5.4 Select Chapter/Track with the >>| or |<< Button
Press the >>| or |<< button during playback to select the next or previous
chapter/track to playback.
Note: Press the >>| or |<< button multiple times to advance multiple chapters/
tracks forward or backward.
5.5 Select Chapter/Track with the Number Buttons
When playing DVD/VCD(PBC OFF)/MP3/WMA/CD , press one of the 1~9
and the 0/10 number buttons to directly select and play the 1st to 10th track
/chapter (the 0/10 button is used as the 10 button).
If you want to play the track/chapter larger than 10, use the 10+, 1~9 and
0/10 button. Example 1: to play the 13th track/chapter, first press the 10+
button once, then press the 3 button. Example 2: to play the 34th track/
chapter, first press the 10+ button 3 times, then press the 4 button.
(The 0/10 button is used as the 0 button)
Note: long pressing the +10 or -10 button can play the next 10th or previous
10th chapter/track(only for MP3/WMA).
5.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the
root/PBC menu)
When playing DVD
1. Press the TITLE button on the remote control to display the title list.

During slow forward, press the PLAY button to resume normal playback.
The function is only for video.
5.9 Display still frame step by step
If the unit is currently playing video, press the TEL button consecutively
to display still frame step by step.
Press the PLAY button to resume normal playback.
5.10 Playback Repeatedly
5.10.1 ONE/ALL Repeat
1. In the mode of DVD playback:
Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL
or REP OFF.
2. In the mode of VCD(PBC OFF)/CD playback:
press the RPT button to select REP ONE, REP ALL or OFF.
When it is in the state of PBC ON, during VCD disc playing, the RPT
button is not available.
3. In the mode of MP3/WMA playback:
Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.
5.10.2 A-B Repeat
Press the A-B button if you want to repeat a specific segment on a disc
that you define:
1. Press the A-B button at a point (A) where you want it to be the start point
of the repeat segment. Press the A-B button again at a point (B) where you
want it to be the terminal point of the repeat segment. Then it will play the
segment repeatedly.
2. To cancel the A-B repeat mode and resume normal playback, press the A-B
button for the third time.
Note:
During VCD/MP3/WMA/CD playback, points A and B must be within the
same track.
2. Press the direction buttons to select your desired title, and then press the OK
or PLAY button to open the root menu of the selected title.
3. Press the direction buttons to select your desired chapter, finally press the
OK or PLAY button to play the selected chapter.
During playback, pressing the MENU button can directly display the root
menu of the title that is playing.
In VCD mode
1. When starting to turn on the PBC function, it will play from the beginning of
the disc till it display the PBC menu on TV screen if the disc include the PBC
menu.
2. Press the number buttons to select your desired track to play.
In MP3/WMA mode
1. The root menu is displayed on the monitor screen all the time(and the TITLE
or MENU button is not available).
2. When displaying the root menu, Press the direction buttons or on the
remote control or direction icons or on the root menu interface to
page up/down the FOLDERS, then tap the Folder your desired to open
the Folder.
After open the Folder, in the same way to select the files to playback.
In CD mode, the TITLE, PBC, MENU buttons are disabled.
5.7 Playback with Speed
During normal playback, long press the >>|/|<< button continuously to fast
forwards or backwards at the following speeds: x2, x4, x8, x20, normal.
During speed playback, press the PLAY button to resume normal playback.
5.8 Playback with Slow Speed
During playback , press the SLOW_FWD button to execute the Slow Forward
function.
With each consecutive pressing of the SLOW_FWD button, the playback
speed decreases. The speed levels in Slow Forward as follows:
x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.

5.11 Playback in Scan Mode
1. When playing VCD(PBC OFF)/CD discs /MP3/WMA sources, press the INT
button to play the previous 15 seconds part of each track on the disc. Press the
INT button again to resume normal playback.
2. When playing DVD , the INT button is not available.
5.12 Playback from a specified chapter/track or a specified time
1. When playing DVD discs , press the SEARCH button to display a
interface and highlight the title item, then use the number buttons to input
the serial number of the title; use the direction buttons to highlight the chapter
item, then use the number buttons to input the serial number of the chapter;
you can still use the direction buttons to highlight the time item, then use the
number buttons to input the desired time to start playback; finally press the
OK or PLAY button to play the selected chapter or play from the selected time.
2. When playing VCD/MP3/WMA/CD content, press the SEARCH button to
display a interface and highlight the track item, then use the number buttons
to input the serial number of the track; you can still use the direction buttons
to highlight the time item, then use the number buttons to input the desired
time to start playback; finally press the OK or PLAY button to play the selected
track or play from the selected time.
5.13 Playback in Random
When playing DVD/VCD(PBC OFF)/MP3/WMA/CD content , press the
RDM button to switch between RANDOM (ON)/RANDOM OFF. When in
RANDOM (ON) mode, it will play in random.
5.14 Playback in Different View-Angle
1. When playing VCD/MP3/WMA/CD sources , the VIEW-ANGLE button on
the IR remote controller is not available.
2. When playing DVD discs , press the VIEW-ANGLE button repeatedly
on the IR remote controller to view in different angle.(This function is only
for the DVD media with ANGLE function)
5.15 Playback in Zoom Mode
In DVD/VCD mode, during playback, press the ZOOM button continuously
to enlarge a certain area of the images on the screen with these multiples:
ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
5.16 Change the Caption Language
When playing DVD's ,press the SUBTITLE button repeatedly to
select the language of the caption or turn off the caption.(depend on the
media used.)
When playing VCD/MP3/WMA/CD discs,the buttons are not available.
5.17 Change the Audio Language
1. When playing DVD discs , press the AUDIO button repeatedly
on the IR remote controller to select the desired language type.
(depend on the media used)
2. When playing VCD discs , press the AUDIO button repeatedly to
select the sound mode of the MONO L, MONO R, MIX MONO and
Stereo, no language function.
3. When playing CD/WMA/MP3 media , the AUDIO button is invalid.
5.18
1. When playing DVD discs , press the OSD button repeatedly on the
remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing title, the
serial number of the playing chapter, the elapsed time of the playing chapter,
the remained time of the playing chapter, the elapsed time of the playing title,
the remained time of the playing title, etc.
2. When playing VCD/CD discs , press the OSD button repeatedly on the
remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track, the
elapsted time of the disc, the remained time of the disc.
3. When playing MP3/WMA media , press the OSD button repeatedly on
the remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track.
Overview of Playback Status

When you select the IMAGE file sort icon, press the ^ or > button to select the
first IMAGE file, then press the v button to select the desired IMAGE file, finally
press the OK or PLAY/PAUSE button to display the image in full screen from
the selected IMAGE file.
3. During IMAGE playback, press one of the >/</^/v buttons to change the angle of
viewing picture that is displaying as follows:
>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT
During IMAGE playback, press the PROG button to change the mode of refresh
picture.
During IMAGE playback, press the STOP button to stop playing and return to the
root menu.
* During IMAGE playback, the following buttons are not available: SLOW-FWD,
SUBTITLE, TITLE, ANGLE, AUDIO, RDM, INT and A-B.
* In IMAGE mode, the other operations are same as ones in MP3/WMA mode.
5.21 Playback MP4 files
1. The root menu is displayed on TV when beginning to switch on MP4 mode,
then it will automatically play the first file.
During playback, press the STOP button to stop playing and return to the
root menu.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER ,file or file sort icon, then press the OK or PLAY button to
open the FOLDER, open the files of the file sort icon or play the selected file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
* The ANGLE, PROG, RDM, INT and TITLE/PBC button are not valid.
* The other functions are same as ones in DVD mode; but the RPT function is
same as one in MP3/WMA mode.
5.22 ESP and ID3 Function
There is ESP function for all formats of discs.
In MP3/WMA mode, during playback, the information of the file name, folder
name, song s title, artist and album will be scrolling on the LCD display.
As long as the current playing MP3 music contains relevant ID3 tag information
in version 1.0/2.0 format, the 3 items underlined above will be scrolling on the
LCD display; otherwise, they will not.
5.23 The DVD System Menu Setup Operation
1. Press the SETUP button on the remote control to access the DVD System
Menu on the monitor.
5.19 Program Playback
It allows you to enter the order in which you want some chapters/tracks in
DVD/VCD/MP3/WMA/CD to play.
1 During playback, press the PROG button to enter a program interface as
follows:
2 Use the direction buttons to move cursor onto the desired place for inputting
the sequence number.
3 Use the number button to input desired sequence number of title/chapter/
track with desired sequence.
4 Use the direction button to move cursor onto Play item, then press the OK
button to play the programmed titles/chapters/tracks in programmed order;
only pressing the PLAY button also can play the programmed titles/chapters
/tracks in programmed order.
* To exit program playback, firstly press the STOP button, then press the PLAY
button to enter sequence playback; or press the PROG button twice again.
* To remove the all programmed sequence numbers, move the cursor onto
Clear item, then press the OK button.
* To change the programmed sequence, move the cursor onto the item you
want to change, input the desired sequence number.
* During VCD playback, if it is in PBC ON mode, at the same time of entering
the state of program playback, it turns off PBC mode.
5.20 Playback IMAGE files
1. The root menu is displayed on the monitor when beginning to switch on IMAGE
mode. .
In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort
icon is for IMAGE file; the right file sort icon is for VIDEO file. If one of these 3
file sort does not exist, you can not move cursor onto the file sort icon.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER, file or file sort icon, then press the OK or PLAY button to
open the FOLDER, or play the selected file, or play only this sort of file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.

5.23.2 LANGUAGE SETUP
OSD LANGUAGE
This item is for selecting the language of the
SYSTEM MENU and all operating prompt
interface displayed during playback.
AUDIO LANG
This item is for selecting a audio language.
SUBTITLE LANG
This item is for selecting a subtitle language.
MENU LANG
This item is for selecting a disc menu language.
5.23.3 AUDIO SETUP
AUDIO OUT
there is only ANALOG mode, i.e. SPDIF/OFF,
not optional.
KEY
It is for selecting your desired basic music tone
(from low to high).
5.23.4 VIDEO SETUP
BRIGHTNESS
It is for adjusting the brightness of the video output.
CONTRAST
It is for adjusting the contrast of the video output.
HUE
It is for adjusting the hue of the video output.
SATURATION
It is for adjusting the saturation of the video output.
SHARPNESS
It is for adjusting the sharpness of the video output.
2. There are 6 setup pages in all for the System Menu. Press the > or < button to
select an desired setup page.
3. Press the ^ or v button to select an setup item in the selected setup page.
4. Press the > button to enter the setup item. Then press the v or ^ button to select
a desired mode of the setup item, finally press the OK button to confirm it.
* Press the < button to return to the upper level.
* Press the SETUP button again or use the direction buttons to highlight the item
of the EXIT SETUP and then press the OK button to exit the System Menu.
For the DVD System Menu, there are 6 setup pages in all. They display as follows:
5.23.1 SYSTEM SETUP
TV TYPE
The setup item is for matching TV screen size.
4:3 PS: Choose the item when connecting a TV set
with 4:3 screen. When playing the pictures with
16:9 size, the left and right parts of the video will be
cut out, and display in full screen.
4:3 LB: Choose the item when connecting a TV set
with 4:3 screen. When playing the pictures with
16:9 size, the top and bottom parts of the TV screen
will be turned into a black square respectively.
16:9: Choose the item when connecting a TV set with 16:9 wide screen.
PASSWORD
This setup item is for locking or unlocking the rating level of the Parental Control.
The defaulted state is locked. The defaulted password is 0000.
You can set a new password that you like: Select the PASSWORD item and then
press the > button to enter it, then input the original password 0000, and then
press the OK button to unlock it. Press the > button to enter it again, then input
a new password that you like and then press the OK button to make it effective.
Before the other persons see the Manual, you should get the password in mind
and cut out the part of PASSWORD in the Manual.
RATING
The item is for setting a new rating level of the Parental Control.
1. Select the PASSWORD item and then press the > button to enter it, then input
the password mentioned above, and then press the OK button to unlock the
setting of the rating level of the Parental Control.
2. Select the RATING item and then press the > button to enter it, then use the
direction buttons to select your desired rating level, then press the OK button
to confirm.
3. Select the PASSWORD item again and then press the > button to enter it, then
input the password, and then press the OK button to lock the new setting of
the rating level of the Parental Control.
DEFAULT
This item is for making all setup items change back to original status.

5.23.5 SPEAKER SETUP
DOWNMIX
It is for selecting your desired sound effect
when there is not central speaker and subwoofer.
There are 3 mode: LT/RT, STEREO, VSS.
LT/RT: When playing a disc with PRO LOGIC
stereo effect, choose the item, so it will
output audio signal with vivid theatre effect.
STEREO: If you choose this item, when outputting
audio signal with 5.1 channels, it will output the left
and right channels of signal ; when outputting audio
signal with 2 channels, it will output the common 2 channels of stereo signal.
VSS: If you choose this item, when playing a disc recorded with 5.1 channels,
the main channel speakers can output audio signal with VSS effect.
5.23.6 DIGITAL SETUP
OP MODE
It is for selecting audio output mode
LINE OUT: It can linearly compress the
audio signal. So the volume level is lower.
You should select the item at night.
RF REMOD: It can make the volume level higher.
You should select it at daylight.
DYNAMIC RANGE
After selecting the compression mode of LINE OUT, set the item, so you can
adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak
value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-
Peak value is the maximum.
DUAL MONO
It is for selecting a desired audio output mode for the left and right ways of signal.
It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:
STEREO, MONO L, MONO R, MIX MONO.
* Parental Control
Q:Why after inserting DVD disc in the disc slot, a dialogue window appears that asks
to input a 4 digits password ?
A:This is because the movie you are playing is rated with the Parental Control, and
the current rating level of DVD player is lower than the current disc. You must change
the Parent Control setting to higher rating level.
! NOTE
* For the factory preset password of the DVD player, please refer to the relative
content of PASSWORD setup menu for details.
Parental Control
The Parental Control function of a DVD player can control the playback of movie
rated level in a disc. You can set the DVD player to be a certain rating level with
SETUP MENU on screen. If the rating level in the disc is higher than one set in the
DVD player, the DVD player can not playback the disc. The rating level setup can
be protected by the password. Therein, if you select Unlock item, the Parental
Control function will be invalid, and all level DVD rating will be played.
The disc movie can be designed as that the DVD player will playback the different
version of content of a same movie according to the different rating level set by
Parental Control. Depending on the DVD feature of seamless switching described
above, the scenes that are not fitting for children will be cleared or replaced by the
other fitting scene automatically.
All rating levels of Parental Control are as follows:
Unlock
1 Kid Safe
2 G
3 PG
4 PG 13
5 PG R
6 R
7 NC 17
8 Adult

* Region Code
Q: Why does the unit display REGION ERROR after inserting disc into disc
compartment ?
A: Because the DVD player and disc has respective region code. If the region
codes of them do not match with each other, the DVD player can not play
the disc.
Appendix: region code of DVD:
The Motion Picture Association of America (MPAA) divided the world into
6 regions, and gave every region a code, namely region code. The region
codes and the countries or areas represented by the region codes as
follows:
Region 1: America, Canada, East-Pacific Inlands;
Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle
East;
Region 3: South-east Asian countries include Taiwan, Hong Kong, South
Korea, Thailand, indonesia, etc.;
Region 4: Australia, New Zealand, Central South America, South Pacific
Inlands;
Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe,
North Korea, North Africa, North-west Asia etc.;
Region 6: China mainland.
5. Bluetooth Hands-Free System
. Pairing and connection
1) Turn on the Bluetooth mode of the mobile phone;
2) Select the item of Finding the Bluetooth Device and enter it. After finishing the finding,
it will show the name of the Bluetooth Device if finding a Bluetooth Device.
Select it and enter it, then it will show a interface that ask you to input a password,
input the password 0000 and then enter it. Then it will tell you pair OK.
3) For some mobile phones, they can automatically connect with the BT device of the
car audio system after pairing is ok; for some mobile phones, they need to select the
paired BT device and press the CONNECTION button . When connection is ok, the
LCD of the car audio system will show LINK OK.
* when pairing is failed, press and hold the PAIR button on the remote control to enter
pairing mode, then the LCD will display PAIR START, then pair and connect with
mobile phone again.
3. Use the mobile phone to do connection or disconnection
In the connection status, find the paired and connected Bluetooth Device, then press
the disconnection button to do disconnection;
In the disconnection status, find the paired and disconnected Bluetooth Device, then
press the connection button to do connection.
1. Enter Bluetooth mode
When you use MODE button or Mode Menu to enter
Bluetooth mode, it will display Bluetooth interface as
right.
In Bluetooth interface, the icons descriptions are as
follows:
: Tap this icon can transfer audio between the
the Car Audio System and phone.
: Tap this icon to turn to call messages interface
as right.
: Tap this icon to turn to audio call mode, call the
name you have record in your phone, then it
will can out automatically.
: When connect with the BT device, the phone
music playback can control by tap this
icon as right.
The other icons are same as ones in the front panel
and Remote Control.
2
MUSIC interface
Bluetooth interface
NOTE interface

7. Troubleshooting
Please read the userl carefully before using the DVD player. If you have any troubles
in using this player, try to solve the problems by the suggestions mentioned below. If you can
not remove the trouble after using all the suggestions, please contact the company or the
technical service center authorized by us. For the sake of your safety, please do not open the
cover and repair the player by yourself, if that, it may cause electric shock.
NO PICTURE, SOUND AND INDICATION
* Ensure that the power switch is on.
* Ensure that the power cord is not damaged or the fuse is not blown.
* Ensure that the power plug is connected to the inlet tightly.
NO SOUND BUT HAVE PICTURE
* Ensure that the players audio output has a good connection with amplifierector is damaged.
* Check whether you have turned down the volume.
* Ensure that you have set the right AUDIO setup of the player.
* Ensure that the audio is not under muted.
NO PICTURE BUT HAVE SOUND
* Ensure that the playertput has a good connection with monitorput.
* Ensure that you have turned your monitor to the AV input channel connecting to your player.
* Check whether the video connector is damaged.
* Ensure that you have set the right VIDEO settings of the player.
BLACK AND WHITE PICTURE OR SCREEN ROLLING
* Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.
FLAWS OF PICTURE OR SOUND
* Check whether the setting of AUDIO is right.
* Check whether the disc is scratched or stained.
* Check whether the AV connector and the output terminal is stained.
* Check whether there is condensation inside the Lens. If so, leave the player off for an hour
or so, then try again.
* Check whether the installation angle is less than 30°.
DISPLAY NO DISC OR BAD DISC
* Ensure that you have put the disc in the unit.
* Check whether the disc is put in the reverse side.
* Check whether the disc is distorted.
* Check whether the disc is stained or scratched badly.
* Ensure that the disc format is compatible to the player.
* Ensure that the temperature inside the car is not too high. If so, cool off till the ambient
temperature returns to normal.
* Replace another disc to insert it into the disc compartment.
REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK
* Check the batteries of remote control and make sure that they are powerful and have
good conductivity.
* Direct the remote control to the IR sensor of the player.
* Check whether there are some obstacles between the remote control and IR sensor.
SOME FUNCTION BUTTONS DO NOT WORK
* Turn off the power, then turn on again.
* Reset the unit to zero, then turn on again.
* Remove the front panel from the unit, then install it again and then turn on again.
THE TFT DISPLAY LOST TOUCH EFFECT
* Insert a disc and press stop button , then press zoom button, finally press the ^ and v buttons to
turn to calibrate mode and then tap the cross cursor as it show until display ok and turn power off
and then turn the unit on again.
4. In the connection status: the audio of mobile phone transfers to the car audio system
whenever a dialling takes place or receiving a call.
5. Dialling when in connection status
5.1 Dial with the mobile phone directly.
5.2 Dial with remote control with the following procedures:
(1) Input telephone number with number buttons 0-9
* Press CLEAR button briefly to cancel the wrongly input number if necessary
(2) Press TEL briefly to execute the dialling.
5.3 To redial the last phone number dialled
Press REDIAL button briefly or tap the icon to validate the last phone number.
6. Accept/Reject/End Call
6.1 When ringing, press TEL button briefly to accept the call;
6.2 When ringing, press HANGUP button briefly to reject the call;
6.3 When talking, press HANGUP button briefly to end the call.
Note: During ringing, the phone number appears.
7. To transfer the audio of a file played by Mobile Phone to the Car Audio Player
In the connection status between the Bluetooth devices of the Car Audio Player
and a Mobile Phone, if the mobile phone can play audio or video files and support
A2DP, when the Mobile Phone plays an audio or video file(For some Mobile Phones,
you must select Play by BT firstly), the audio of the playing file will be transferred
to the Car Audio Player.
In A2DP mode, if the Bluetooth device of the Mobile Phone support AVRCP, the
functions of the >>|, |<< , PLAY/PAUSE , EJECT, MUTE, EQ, LOUD, + , - and SEL
buttons are the same as one in media mode(no fast forward/backward functions for
the >>|/|<< buttons). The other buttons available in media mode are not available.

8. Specification
General Specification
Power Supply Requirement..................................................DC 12V
Maximum Power Output................4 x 85W(measured at DC 14.4V)
Dimensions(wx hxd)...............................................7"Wx2"Hx6.3"D
DVD Deck Specification
Format.....................................DVD/VCD/JPEG/MP4/MP3/WMA/CD
Video System........................................................................NTSC
Audio System..............................................................24 bit/96KHz
Loading System.......................................................... Auto Loading
Mounting Angle.................................................................0 to +/-30
Video Specification
Video Type...................................................................16:9 and 4:3
Video Output level......................................Composite:1.0± 0.2Vp-p
Load impedance: 75 ohms
Horizontal Resolution................................................................500
Audio Specification
Audio Output(Analog audio)..........................................2.0+0-1.0Vrms
Frequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)
S/N Ratio(Audio).............................................≥90dB(at 1KHz 0 dB)
Separation..............................................................................50dB
Radio Specification
FM Section
Frequency range.......................................87.5MHz - 107.9MHz(US)
87.5MHz - 108.0MHz(EU)
Usable sensitivity......................................................................3uV
I.F Frequency....................................................................10.7MHz
AM Section
Frequency....................................................530KHz - 1710KHz(US)
522KHz - 1620KHz(EU)
Car Audio & Electronics Unmatched technology for unforgettable driving