Platinum Access Systems PA1220 User manual

PA1220
RF KEYPAD CARD READER
USER MANUAL
Rev. B
Platinum Access Systems Inc.

SPECIFICATIONS AND FEATURES
1. Key Code Range
5 digit code: 00000-99999
4 digit code: 0000-9999
Memory Capacity: 10,000 (4 digit), 100,000 (5 digit) codes
2. RFID Card Reader
Card Code Capacity: 2000 Cards
3. Keypad
Keys: 0-9, "*" start over, "#" command code
Key entry timeout: 15 sec (uncompleted key code will be ignored in 15
sec idle period.)
4. RF Remote Control
Working with Platinum RF receiver to provide >50ft remote control.
5. Hold Open Code
Resettable 5 digit code to turn on/off hold open operation.
6. Request to Exit Input
A contact input for codeless open activation..
7. Adjustable Control Output Strike Duration
0-99s output relay and RF control strike duration.
8. Slave Mode
It can be set to slave mode to work with master. All codes entered will
be send back to master to verify, Master will send gate open command
upon valid key code. 99 slave ID’s can be set with on board rotary
switch.
9. Backlit Key
Back light of the keys will be turn on automatically when the
environmental light is dimmed.
10. Control Output
a. NO/NC relay output with 10Amp @ 120VAC or 8A @ 30VDC.
b. Solid state output with 0.5A sink current.
11. Battery Backup
Internal rechargeable battery provides >24 hours power backup.
12. Solar Panel Ready
A 12V/20W solar panel can be connected to power the unit and charge
the battery for AC power free operation.
INSTALLATION
1. Wring
See Fig.1.
a. Connect 9V/2A AC/DC adaptor to “AC/DC” terminals.
b. Connect solar panel to “SOL” terminals.
c. Connect the internal battery to either “BAT1” or “BAT2” terminal.
d. Connect NC/COM/NO to external device under control.
e. Connect “EXIT” to external strike open switch.
f. Connect RS485 cable from master to either of the RS485 terminals.
2. Set the Mode DIP Switch
a. Set 4 or 5 digit length operation by “DIG” side DIP SW.
b. Set master/slave by side “M/S” side DIP SW “M” or “S”.
3. Set the Slave Device ID
Set slave device ID by the 2 rotary decimal SW. set range 00-99.
4. Indicator and Mode Switch Locations
See Fig.2.

NC
COM
NO OUT
GND
EXIT
Fig.1
Fig.2
OPERATIONS
1. Normal Mode
Selected by Mode SW (“NORM” position), "Red" light flash
a. To open gate by key code, enter 4 or 5 key code.
b. To open gate by card, sweep card to activate control relay.
c. To hold open, enter #3xxxxx. xxxxx: 5 digit code
(00000-99999)
d. To release hold open, enter #3xxxxx again.
Status:
Beeping twice with green light: Success
Beeping once: Code is not match
2. Program Mode
Selected by Mode SW (“PRGM” position), "Yellow” light on.
Program Key Code: Enter 4 or 5 key code
Program Card without Card ID: Sweep card.
Program Card with Card ID: Enter card ID, #5xxxx (xxxx: 0000-1999
card ID), Then sweep RFID card to program the card code into ID
0000-1999.
Note: Sweep RFID card one by one sequentially, the card ID will
automatically increase by 1.
Status:
Beeping twice with green light: Program success
Beeping once with red light: Program fail
Program Command:
a. RF receiver control channel (default ch1, receiver relay channel)
#101 Control ch1
#102 Control ch2
#103 Control ch3
#104 Control ch4

b. Control output strike duration (default 1s)
#2xx xx: 00-99s
c. Hold open code
#3xxxxx xxxxx: 5 digit code (00000-99999)
3. Erase Mode
Selected by Mode SW (“ERAS” position), "Yellow” light flash.
Erase Key Code: Enter 4 or 5 key code
Erase Card Code without Card ID: Sweep the card.
Erase Card with Card ID: Enter card ID #5xxxx.
xxxx: 0000-1999 card ID
Erase Command:
#911 Erase all codes
#913 Erase hold open code
Status:
Beeping twice with green light: Erase success
Beeping once with red light: Erase fail
4. Program RF Receiver
Platinum RF receiver needs to be programmed to save the RF control
code of this unit.
a. Set the unit to “NORM” mode.
b. Program one card per the steps above.
c. Place RF receiver close to this unit, Turn on RF receiver power.
d. Open RF receiver cover and locate the programming button.
e. Push the programming button in RF receiver.
f. When the programing LED is on in RF receiver, sweep the card.
g. When the programming is done, the programming LED will go off.
h. Sweep the card again, and check the relay in receiver is activated.
i. If the programming is unsuccessful, repeat step d to g.
5. Slave Mode
When the unit is set to “SLAVE” mode, all key and card will sent to
master to process. Master will send “Open Gate” command upon valid
code.
6. EXIT Input
“EXIT” input will activate control output at any time.