Playcraft PTBARWOS08-Barcelona User manual

ASSEMB
LY INSTRUCTIONS
Models: PTBARWOS08-Barcelona

assistance.
1) Your table is designed for use indoors in a climate controled environment only.
Damage can occur if the table is exposed to water, dampness, high humidity,
freezing temperatures, etc.
2) Professional assembly is strongly recommended. This assembly manual is intended to
guide an experienced slate pool table installer with the assembly process of this
for which the process is the same regardless of the cabinet type.
2) The pool table cabinet and slate are extremely heavy. Two or more people are
required for assembly.
or serious injury.
5) Only use the table for its intended purpose.
6) Damaged or worn parts may be dangerous for users and the integrity of the table.
will void the warranty.
8) Check all screws, bolts, etc. on a regular basis to ensure that they are in good working
as required with owning a slate pool table
Rio Grande

PARTS LIST
NO. IMAGE DESCRIPTION SPECIFICATION QTY UNIT
①
LEG 1100*200*663 2 PCS
ASSEMBLY POSITION FRAME
②
LEG PANEL 1717*180*60 1 PC
ASSEMBLY POSITION FRAME
③
SUPPORT BEAM 1173*180*40 2 PCS
ASSEMBLY POSITION FRAME
④
LONG BEAM 1936*180*40 2 PCS
ASSEMBLY POSITION GRADE A BEAM
⑤
MIDDLE BEAM 893*120*40 2 PCS
ASSEMBLY POSITION GRADE A BEAM
⑥
SIDE SLATE 1 805*1295*40 1 PC
ASSEMBLY POSITION TOP RAIL
MIDDLE SLATE 805*1295*40 1 PCS
ASSEMBLY POSITION TOP RAIL
SIDE SLATE 2 805*1295*40 1 PC
ASSEMBLY POSITION TOP RAIL
⑦
1 PC
ASSEMBLY POSITION TOP RAIL
⑧
LONG RAIL 2562*163*160 2 PCS
ASSEMBLY POSITION TOP RAIL
⑨
SHORT RAIL 1443*163*160 2 PCS
ASSEMBLY POSITION TOP RAIL
CLOTH /

HARDWARE LIST
NO. IMAGE DESCRIPTION SPECIFICATION
QTY
UNIT
H1
DOUBLE HEAD BOLT ø10*100 4 PCS
FOR BOTTOM SUPPORT BEAM AND LEG ASSEMBLY
POSITION
H2
ACRON NUT M10 4 PCS
FOR BOTTOM SUPPORT BEAM AND LEG ASSEMBLY
POSITION
H3
FLAT WASHER M10*30*2 4 PCS
FOR BOTTOM SUPPORT BEAM AND LEG ASSEMBLY
POSITION
H4
BOLT NUT M10 4 PCS
FOR BOTTOM SUPPORT BEAM AND LEG ASSEMBLY
POSITION
H5
HEX BOLT ø12*180 4 PCS
USED TO FIX THE CROSS BEAM ASSEMBLY
POSITION
H6
FLAT WASHER M12*30*2 12 PCS
4PCS FOR BOTTOM SUPPORT BEAM,8PCS FOR TABLE FRAME
AND LEG
ASSEMBLY
POSITION
H7
ACRON NUT M12 4 PCS
USED TO FIX THE CROSS BEAM ASSEMBLY
POSITION
H8
SCREW 4.2*60 8 PCS
USED TO FIX THE MIDDLE BEAM ASSEMBLY
POSITION
H9
HEXAGON BOLT ø12*60 8 PCS
FOR CROSS BEAM AND TABLE LEG ASSEMBLY
POSITION
H10
SLATE LEVELER ø10*75 16 PCS
USED TO ADJUST AND LEVEL THE SLATE PCS
H11
RUBBER SHIM 2mm*2pcs
3mm*2pcs 4 PCS
TO ADJUST THE TABLE LEG ASSEMBLY
POSITION
H12
SCREW 6*60 12 PCS
USED TO FIX THE SLATE AND FRAME ASSEMBLY
POSITION

H13
BARREL NUT ø8*30 4 PCS
USED TO FIX THE TOP RAIL AND CORNER ASSEMBLY
POSITION
H14
DOUBLE HEAD BOLT ø8*80 4 PCS
USED TOCONNECT #2 AND #5 TOP RAIL ,#3 AND #6 TOP RAIL ASSEMBLY
POSITION
H15
ACRON NUT M8 4 PCS
USED TO FIX THE TOP RAIL AND CORNER ASSEMBLY
POSITION
H16
FLAT WASHER M8 4 PCS
PLEASE SEE TEH INSTRUCTION ASSEMBLY
POSITION
H17
BOLT NUT M8 4 PCS
PLEASE SEE TEH INSTRUCTION ASSEMBLY
POSITION
H18
METAL CONNECTOR / 4 PCS
USED TO FIX THE TOP RAIL AND CORNER ASSEMBLY
POSITION
H19
ALLEN BOLOT ø6*16 16 PCS
USED TO FIX THE TOP RAIL AND CORNER ASSEMBLY
POSITION
H20
HEXAGON BOLT ø10*60 18 PCS
USED TO FIX THE TOP RAILS AND SLATE ASSEMBLY
POSITION
H21
DOME WASHER M10*30*5 18 PCS
USED TO FIX THE TOP RAILS AND SLATE ASSEMBLY
POSITION
H22
SIDE POCKET 4 PCS
ASSEMBLY
POSITION
H23
MIDDLE POCKET 2 PCS
ASSEMBLY
POSITION
H24
SCREW 4.2*16 12 PCS
ASSEMBLY
POSITION
H25 TOUCH-UP-MARKER PEN 1 PC

Code #
Attention: There are some code number(#--#) writing on both bottom ends of each short and long
rails, please connect 2 rail ends together correspondingly with the same code # by sequence in
order to avoid some big gap between each 2 ends.