Playlearn BWWMP User manual

MADE IN CHINA
WALL MOUNTED BUBBLE WALL (BWWMP)
Installation and Operation Instruction
Use only distilled water- 14 Litres required
Unpack all components and check contents against inventory list below.
Advise supplier immediately if parts are missing.
Brief Description for Components
No
Name of parts
Function description
1
One (1)-Metal Frame
Brushed Stainless Steel Frame.
2
One (1)-Acrylic Panel
Acrylic panel is used to hold water, display of dancing
illuminated bubbles.
3
One (1)-Hanging bar
A board to fix screw on wall for hanging bubble wall.
4
One (1)-Remote Control
To control the color and the light of LED LIGHT.
5
One (1) -Water-Pump
Produce Air & generate bubbles.
6
One (1)-Transformer
Supply Power.
7
One (1)-Metal Screw
Screw used to fix the Hanging bar on wall.
8
One (1)-Controller
Equipment designed to receive remote control order.
9
One (1)-PVC Water Pipe
PVC Water Pipe is tool for water injection in and draining
water off from Acrylic Panel.
10
Two (2) - Blue Nozzles
Outlet of gas that connects with the Air-pipe in pump.
11
One (1)- Taper sleeve
The raw plugs
Components Photos
Specific Installation steps as follows:
IMPORTANT: 2 peoples are required to safely assemble and install this unit.
Do not attempt to assemble on your own.
Step 1
Fix the hanging metal with screw on your suitable wall.
Step 2
Connect the transformer cord to the controller cord which is on the bottom side of acrylic
panel.
Step3
Carefully add water through the top of panel until reaching max level mark.
Hang the bubble wall with two people on the hanging metal on the wall.
Step4
Plug transformer into mains power supply.
Caution & Maintenance
The controller should be out of the base when in use.
Ensure the blue nozzles are inserted properly in the acrylic panel and connected with the
Air-pipe from the pump in case of any water leak.
Ensure the air-pipe is straight to avoid any bubbles coming out.
The bubble wall will continue to lose water due to evaporation after a few months of
operating, which is dependent on a many variables such as climate, humidity,
temperature, etc. it may be require to refill water.
It is recommended to clean the inside of your bubble wall every three month with mild
lotion and a soft towel.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS
INJURY OR PROPERTY DAMAGE. Proper and complete assembly and good use are
essential for proper operation and to reduction the risk of injury. 2 people are required for
assembly. • If technical assistance is required, contact the vendor.
Most injuries are caused by misuse and/or failure to follow instructions.
Do not attempt to move the assembled unit once it’s filled with water. Turn Power off this unit
before removing.

MADE IN CHINA
FREQUENTLY ASKED QUESTIONS
1, How to correctly use the water pipe to siphon water?
Firstly, fill the pipe with water,
Secondly, ensure the water pipe should be full of water then press the two ends of the water
pipe with your fingers tightly,
Thirdly, remove one finger from one end of the water pipe; put this end into the water of the
acrylic panel. Meanwhile make sure the other end is still closed.
Lastly, open the other end of the water pipe and turn towards the bucket, the water will flow
out through the water pipe automatically.
Firstly Secondly Thirdly Lastly
2. Why Bubbles come out unevenly? What I should do when the bubbles are in
different size? You could use the adjuster. Firstly, you should observe the bubbles,
A: If the bubbles in any one channel of one group are bigger, twist the corresponding knob
counter-clockwise a little,
B: Then twist slightly the rest knobs of one group to get the all bubbles evenly.
3. Why is not there air expel from outlet of gas?
When you have this issue, you should consider that one of the outlets of gas has been
blocked. Turn off all other adjuster to make all air came out from the blocked outlet of gas.
Blockage will be blown out. Then adjust button again to get the all bubbles evenly .Please
refer to Article 2 of the FAQ for operation in details.
4. What kind of water is fit to bubble wall?
Distilled water and pure water are recommended for the bubble wall to prevent the calcium
deposits and algae producing in the acrylic panel. Domestic water is also ok, but it will cause
bacterium, algae and calcium deposits.
Deposits will be easy to block the outlet of gas.
5. How often do I have to change the water inside of the acrylic panel?
In normal conditions, you should change water every three months.
6.How to clean the acrylic bubble wall when it gets dirty?
You should wet a soft cloth with water to wipe the penal gently . If any algae produced, please
use mild lotion with water and softly towel , then rinse off with clear water . Any acidic solution ,
alkaline solution as well as brushers and edge- tool are strictly forbidden during cleaning.
7. What is the standard of the water level?
Please refer to the standards of the level water mark Stuck on the Acrylic panel. Please don't
exceed the Max level of water mark to avoid water running out of the panel which will make
the damage on the machines or safety accidents.
8. Could we do something about the broken LED lights?
The LED lights installed on top and bottom are replaceable .The LED light fixed right and left
without metal frame can't be replaced.
9.What should we do if the remote controller can't work ？
Please make sure that the remote controller is pointing at the sensor under the acrylic panel
then test , If it still doesn't work the problem will be the battery has run down .You should
change remote controller timely,. Aim straight at the sensor makes better use of remote
controller.
10. Why doesthe LED light not work well?
Please check all the wire connection and make sure they connect well. Power supply is
absolutely necessary. Press the key of "ON “to check the led light.
If you need any advice or help with set up, please contact;
Playlearn Ltd by email - [e-mail]
or call 0161 737 5099
5-6 Agecroft Trading Estate, Langley Rd, Salford, M6 6JD