Playlearn Hello! User manual

Hello!
I am your new Standing Bubble Wall
USER MANUAL

CONTENTS
1
2
Lid
Panel
3
Rocks
5Base
8Adapter 9Remote
7Controller Box
(attached to panel)
6Air Pump
(attached to base)
10 Maintenance Hose
(manual pump and water pipe)
For emptying and changing water -
not needed for setup
Make sure we’re all in your box
4
Tray

DISTILLED WATER / REGULAR WATER
Although this product has been designed to work
well with tap water, the product will need higher
maintenance due to algae and the water becoming
cloudy. The water will need changing approximately
once every few months. By using distilled water, the
water and product will stay clean for longer.
Place the base on floor / flat surface and remove the trays (#4 on
Contents Page).
Slide panel into base. While doing this make sure not to trap the
white air tubes. Connect the black wire coming out of the air
pump to the white wire coming out of the controller box.
Connect the white tube from the panel to the air pump. They are
intentionally a little stiff, in order to keep them from slipping out.
Add water until panel is about 10% full.
Feed the adaptor wire (#8) though the hole, into the base (#5).
Connect the adaptor to the power port on the controller box (#7)
and switch it on with the remote (#9) or the app.
WATER
the simple
joys in life
BRING A FRIEND ALONG
We recommend setting up with two people
INSTRUCTIONS
1
2
3
4
5
know
know
OUR COMMITMENT TO YOU
Here at Playlearn, we have spent many years developing our Bubble Walls and Bubble
Tubes to ensure they are simple to set up and trouble-free, so you can spend more time
enjoying it and less time setting it up. We want you to love your Bubble Wall, so please
let us know if any questions come up. Please email us at [e-mail] and
we will get back to you within 48 hours. The Bubble Wall is a delicate product and must
be looked after and maintained to get optimal use. Any time maintenance is required
(and certainly for emptying the water!), we recommend that two people do this together.

EMPTYING WATER FOR MAINTENANCE AND STORAGE
We have provided a maintenance hose to aid in emptying your Playlearn Bubble Wall.
Attach the water pipe to the nozzle closer to the handle on the manual pump and place
the other end of the pipe deep into the panel. Place a large bucket on the floor (or at a
lower point than the end of the pipe) and start pumping until the water starts flowing.
8
9
7
6
Test the product with the remote control (#9) or the app. Check that the
product is working properly.
Fill Bubble Wall with water until 2” from the top of the panel (#2).
PLEASE NOTE Jets can take up to 24 hours to reach their full operating
capacity. Please allow for this time for them to “break in”.
Place the lid (#1) onto the top of the Bubble Wall.
Return the trays (#4) to the base (#5) of the Bubble Wall. Fill the trays with
the decoration rocks (#3).
Place the customer support sticker on your Bubble Wall in case your need
to reach out to us at any time.
know
know
REMOTE
The remote operates the following way:
Power Turns the product on and off
Play/Pause Turns the light on and off
Brightness Adjusts the brightness of the light
Colors Changes the light to button color
Auto Light will gradually change between all colors
Jump 3/Jump 7 Light will jump between red, green and blue /
Light will jump between all 7 colors
Fade 3/Fade 7 Light will fade between red, green and blue /
Light will fade between all 7 colors
Flash Light will flash on and off
Speed +/- Increases/decreases speed of the light changing
See next page for app insturctions.
10

CRACKED PANEL If your panel is cracked, please contact customer support
immediately.
NO BUBBLES COMING OUT If the pump is not making noise, please
check that the pump is connected to the crontoller box (instruction #2). If the
connection is correct, but the pump still isn’t making noise, please contact
customer support.
If the pump is making noise, please check that the white tube is connected
to the air pump (instruction #3). If the connection seems okay, please
check along the whole length of the white tube to ensure it is not kinked
or bent. If all seems right, please pull off the pipes attached to the pump
and feel if air is coming out. If no air is coming out of the pump, please
contact customer support. If air is coming out, reattach the pipes and
check at the other end to ensure that the pipes leading into the panel
are letting out air. If no air is coming out of the pipe, the exit is blocked
somewhere along the pipe. Please contact customer support. If air is
coming out of both exits, please refer to the next section.
SOME JETS ARE WORKING, SOME ARE NOT On occasion, some of the air
jets break in faster than the others. Since some are fully “broken into”,
the water is bypassing the jets that have not yet “broken in”. If this occurs,
follow these steps. Under each air jet, at the bottom of the panel, is a small
dial that can be adjusted. Ensure that the dial under the non-working jets
are open, by loosening them. Then, close the dials under the jets that are
currently working by tightening them. This should stop around 90% of the
bubbles. By doing this, pressure will be forced into the open jets, forcing the air
bubbles to break through them. Please keep it like this for a few hours, to allow
the jets to be fully “broken into”. After a few hours, you can adjust all the dials back
to a regular, even setting.
REMOTE CONTROL NOT FUNCTIONING The remote control is designed to change the
colors of the lights and to change the light pattern. If the lights are on but they are not
changing with the click of the remote control, try going a little closer to the base of the
Bubble Wall. The red LED light turning on doesn’t mean there is a good battery. If it still
does not work, please change the battery. If this fails to fix the problem, contact customer
support for a replacement.
NO POWER First, touch the adaptor and see if it feels warm. If it is cold, contact customer
support for a new adaptor. If the adaptor is warm, check the connection into the controller
box (instruction #5) by removing and reinserting it and press the “on” button on the remote
control. Check the white wires coming out of the controller box are firmly connected to the
plug and lights. If this still does not resolve the problem, please contact customer support.
CAUTION Always unplug the power before cleaning and handling. Disconnect and drain
the water if storing away for an extended period of time. Do not operate with hot or ice-
cold water. Do not lift, carry or pull the Bubble Wall by the power cord. Do not exceed the
maximum voltage and wattage on adaptor.
STILL STUCK?Confused? Any further questions? Please contact customer support and one
of our reps or techs would be happy to walk you through it.
grow 845-362-0638 [email protected]om

WARRANTY INFORMATION Thank you for choosing Playlearn’s Bubble Wall. All of our
products are made with the highest quality materials. In the event that a product
does not have our usual standard of excellence, we will repair or replace it, at our
discretion, within 12 months from the date of purchase. A valid proof of purchase,
with the purchase date clearly indicated, must be provided. Photos of defective
merchandise may also be required to help us evaluate the cause of the defect.
WATER DAMAGE This product is not manufactured to withstand extreme
temperatures. Improper storage that allows water to freeze within the Bubble
Wall will cause damage and is not covered under the warranty. The use of “hard
water” and/or caustic cleaners can affect the finish of the Bubble Wall. Failure
to keep the unit clean, and use of additives/cleaners, will also void the warranty.
NOT COVERED UNDER THE WARRANTY The warranty will NOT cover cases of
damage due to: inadequate care, immersion in water or improper installation,
storage or maintenance.
This warranty also does not cover any additional charges or installation, removal,
disposal, shipping costs or consequential damage associated with any warranty
claim.
SETTING UP THE APP
Search your phone’s app store for “Playlearn”.
Make sure your Bluetooth is “on”. Download and open the app.
Press the menu icon on the top left corner.
Press “my devices” and select the device listed in drop down until the
connected link icon.
Your Bubble Wall must be turned “on” to establish a connection to
the app.
QR CODE

Enjoy!
Continue your Playlearn experience