Plinius P10 User manual

2
CONGRATULATIONS on your decision to become the proud owner of this
Plinius SA-Reference Power Amplifier.
This manual has been prepared to help you understand the operation of your amplifier, and to provide
information about its design and the variety of ways it may be used.
We have designed and manufactured this amplifier to reproduce faithfully and accurately, your favourite
music. With a little care and a full understanding of the operating recommendations in this manual, your
Plinius SA-Reference Power Amplifier will provide years of high-quality, trouble-free performance.
Serial Number: ................................................................................
Final Test Certified By: ................................................................................
IMPORTANT: PLEASE TAKE THE TIME TO READ THIS MANUAL
THOROUGHLY BEFORE USING YOUR AMPLIFIER.

3
DESIGN PHILOSOPHY
From a distance you can see that the design of the Plinius products is more than an applied styling
exercise to the front panel. We have started from the ground up to produce a casing for our electronics
that is unrivalled in its physical strength and visual simplicity. Wherever possible we have reduced the
number of parts needed and then invested massively in refining and producing the remaining parts to the
highest quality achievable with state of the art computer controlled machines allied with expert craftsman.
Examples of this approach include the hydraulically formed corners on the amplifiers giving much greater
strength and the one piece housing for the remote control unit that eliminates large joints and potential
creaks.
The very process of holding the remote tells you that you are controlling both a powerful and precise
product. It is designed specifically for the act of listening to music, not channel surfing on a television or
changing the room temperature. The distinction is important because we believe that listening to music is
a highly selective and emotional experience that requires a much greater level of concentration and
precision to fully appreciate and enjoy.
As with music that you are not familiar with, truly innovative new designs can take time to understand and
enjoy. How often have you heard music that you were first unsure of, that over repeated listening, has
become a firm favourite. Our designs are fundamentally different to many other companies, and we hope
that you will take the time to explore their unique character and qualities because we have not made them
different simply to be different. We genuinely believe that their visual and tactile qualities do improve the
experience of listening to music and that is our design goal!
Ross Stevens
Design Director.

4
CONTENTS
Introduction .................................................................................................................................... Page 3
Precautions ..................................................................................................................................... Page 5
Amplifier Features - FRONT PANEL .................................................................................................. Page 6
Amplifier Features - REAR PANEL .................................................................................................... Page 8
Amplifier Configuration Selector (ACS) ............................................................................................ Page 9
Balanced/Unbalanced Signals ........................................................................................................ Page 10
Installation and Operation .............................................................................................................. Page 12
Input/Output Connection ................................................................................................................ Page 13
RCA Connection ............................................................................................................................ Page 14
XLR Connection ............................................................................................................................ Page 15
SA-Reference Features .................................................................................................................. Page 17
Loudspeaker Selection .................................................................................................................. Page 19
Why Class A is better .................................................................................................................... Page 20
Specifications ............................................................................................................................... Page 21
Index ............................................................................................................................................ Page 22
Contact Details .............................................................................................................................. Page 23

5
PRECAUTIONS
Please take special note of the following precautions before operating your new amplifier:
• The Plinius SA-Reference Power Amplifier can be operated in mono mode delivering up to 1000 watts
into 8 ohms. This amplifier is also capable of a very large peak current delivery.
• The Plinius SA-Reference Power Amplifier operates in Class A. It is capable of generating
temperatures that could have an adverse effect on other equipment, furniture etc. DO NOT leave
flammable material on the amplifier whilst running, as this could pose a serious fire risk.
• The Plinius SA-Reference Power Amplifier is of direct-coupled design, and offers no protection from
preamplifiers that have a high DC component at their outputs.
• This amplifier operates at hazardous voltage levels. Any work requiring removal of the lid or base of
this amplifier must be referred to a suitably qualified and experienced service technician.
• DO NOT attempt to connect any input of this amplifier to it’s own outputs.
• DO NOT earth any output terminal or connect any of these terminals together without following the
instructions in this manual or seeking qualified assistance.
• DO NOT place this amplifier in any position where liquids or any foreign material may accidentally
enter it.
• DO NOT connect any voltage source, short circuit, earth/ground or appliance (other than suitable high
fidelity loudspeakers) to the amplifier output terminals.
• Some preamplifiers, processors, CD players’ etc. produce large switching pulses when switched on
causing a loud click through the loudspeakers. For this reason, turn on all other equipment in your
system before turning on your Plinius SA-Reference, or ensure that the amplifier is in MUTE. You will
not experience this phenomenon with Plinius Preamplifiers.

6
AMPLIFIER FEATURES – FRONT PANEL
FRONT PANEL LAYOUT SHOWING MUTE AND BIAS SWITCHES
MUTE SWITCH
It is not recommended practice to interfere with the input cables while the amplifier is switched on and
connected to the loudspeakers, so a Mute button is fitted to interrupt the input signal. This allows you to
connect and disconnect the input cables without the necessity of turning the amplifier off.
When the amplifier powers up from start, the Mute automatically closes and has to be switched for normal
listening. Press the button once to open the mute, and again to close it. The mute also disconnects the
speakers while the LED is on.
CLASS A SWITCH
This switch on the right of the panel alters the operating bias of the amplifier. Press once to activate Class
A, and again for Class AB. In Class A the LED is ON. Either mode may be used for listening, with Class A
preferred.
CLASS AB: This position reduces the bias on the output stage to operate the amplifier in Class AB. This
is a bias configuration used by the majority of high fidelity amplifiers. In Class AB your Plinius SA-
Reference produces very high quality sound, suitable for all occasions where ‘super critical’ listening is
not a priority. The quality of performance in this mode may exceed that of many other amplifiers so a dual
benefit exists in that this facility provides the user with a much cooler operating temperature, and a much
reduced demand on electricity particularly at idle (while the amplifier is not reproducing music). This
unique feature allows you to leave the Plinius SA-Reference switched ON at all times, rendering the
amplifier ready for use and requiring only a few minutes of warm-up in Class A before the very best of the
amplifier's sonic qualities may be experienced.
MUTE CLASS A

7
CLASS A: This position provides Class A bias to the output stage therefore ensuring the optimum
performance of the amplifier during all listening events. Class A amplifiers run hotter than Class AB
amplifiers, hence our specially designed and distinctive heat sinks. Operating the amplifier in Class A
necessitates two precautions that should be observed.
1. On switching to Class A, the temperature of the amplifier will quickly increase and the amplifier will
become quite hot. Once again we remind you to ensure that you have left adequate space around
the amplifier for ventilation. Ensure that no objects are resting on the amplifier and check that the
heat sink (cooling fins) are not obstructed in any way.
2. The power required from the mains supply in Class A is approximately 1,000 watts, similar to a
small electric heater. The amplifier should not be connected to a wall outlet that is shared with
other heavy current appliances such as heaters or electric motors. If in doubt, check with your
Plinius dealer for advice.

8
AMPLIFIER FEATURES – REAR PANEL
This panel incorporates all the terminals for connecting the input signals from your preamplifier, and
output to the loudspeakers, and mains supply. A reasonable understanding of this amplifier’s operation
and a logical approach should ensure that you are able to make all connections with ease.
Please remember that your Plinius SA-Reference Power Amplifier is a high quality electronic instrument
capable of an exceptional level of performance. Be sure that you understand your system’s requirements
fully before you make any connection to this amplifier or adjust the ACS (Amplifier Configuration
Selector).
PLINIUS SA-REFERENCE REAR PANEL SHOWING ALL THE AVAILABLE FACILITIES
INCLUDING INPUT AND OUTPUT TERMINALS, ACS (AMPLIFIER CONFIGURATION SELECTOR),
MAINS INPUT AND GROUND LIFT.
+
+
DESIGNED AND MANUFACTURED IN
NEW ZEALAND B
Y
PLINIUS AUDIO LTD
P.O. BOX 1836
PALMERSTON NORTH
CAUTION
RISK OF ELEC TRICAL SHOCK
DO N OT OPEN
CAUTION:
T
O RE DUCE RI SK O
F
COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICIN G TO
QUALIFIED SERVICE PERSONNEL.
SERIAL No. POWER
CONSUMPTION
50
/
60 2000VA
V
OLTAGE Hz.
PLINIUS SA-Reference
STEREO POWER AMPLIFIER
GROUND
LIFT
CHASSIS
OPEN
RIGHT OUTPUTS LEFT OUTPUTS
CAUTION: ENSURE ADEQUATE VENTILATION
+
+
ON / OFF REMOTE
T
RIGGER
T
ERMINALS
+12V GND
AMPLIFIER CONFIGURATION SELECTOR
REFER TO OWNERS MANUAL FOR USAGE INSTRUCTIONS
RCA STEREO
RCA BRIDGED MONO
X
LR BALANCED MONO
X
LR STEREO
RIGHT INPUTS LEFT INPUTS
ALL MONO/BRIDGE OPTIONS USE RIGHT INPUT
AND LEFT + RIGHT+ OUTPUTS ONLY

9
AMPLIFIER CONFIGURATION SELECTOR
REFER TO OWNERS MANUAL FOR USAGE INSTRUCTIONS
RCA STEREO
RCA BRIDGED MONO
XLR BALANCED MONO
XLR STEREO
A
LL MONO/BRIDGE OPTIONS USE RIGHT INPUT
AND LEFT + RIGHT+ OUTPUTS ONLY
INPUT TERMINALS
Input terminals for your Plinius SA-Reference Power Amplifier are easily accessible and fitted to the top
centre area of the rear panel. A brief summary of connection possibilities is listed below, while a more
detailed explanation follows later in this instruction manual.
RCA INPUTS LEFT & RIGHT: These standard RCA terminals are for use with unbalanced signals from
most signal sources such as audio preamplifiers.
XLR BALANCED INPUTS LEFT & RIGHT: XLR connectors fitted to this amplifier are for use with balanced
line signals from audio preamplifiers. Balanced signals are carried via a three way cable that connects all
three pins at each end of the interconnect cable.
The XLR pin configuration used in all Plinius product is:
PIN 1 to GND
PIN 2 to +Signal
PIN 3 to -Signal
NOTE: Because of the way our XLR and balanced inputs are configured it is not possible to connect both
XLR and RCA at the same time.
AMPLIFIER CONFIGURATION SELECTOR (ACS)
The Amplifier Configuration Selector (ACS) is a unique switching method that exploits all of the
operational features of your Plinius SA-Reference Power Amplifier. By using this switch it is possible to
operate your amplifier with either balanced or unbalanced signals and achieve a stereo or mono output.
Stereo or Mono use of this amplifier will depend on the type of ancillary equipment employed with your
system. If you wish to use this amplifier as a single channel (mono) Power Amplifier in a stereo high
fidelity system, then another SA-Reference will be required for the other channel. This will provide an
extremely high performance option.
AMPLIFIER CONFIGURATION SELECTOR

10
The ACS switch options are:
RCA STEREO: This option provides a stereo output via both left and right output channels from a stereo
signal connected to both left and right input RCA inputs.
RCA BRIDGED MONO: This option configures your amplifier to drive one loudspeaker from one
unbalanced signal fed to the RIGHT RCA input. The loudspeaker is connected to both channels positive
(+) output terminals, giving an available power in this mode four times the rated output of the amplifier,
approximately 1000 watts into 8 ohms. Special care must be taken in connecting the input signal and
loudspeakers to ensure safe operation and best possible performance.
XLR STEREO: This option provides a stereo output signal from a balanced stereo input signal connected
to both the left and right XLR inputs. All the advantages of balanced line transmission will be realised with
good rejection of noise and some freedom from earth or ground loops (hum).
XLR BALANCED MONO: In this mode both channels of your Plinius SA-Reference combine to operate as
a true balanced mono amplifier, from input to output. This configuration provides the highest quality
mono performance from a balanced line input connected to the RIGHT BALANCED XLR INPUT. As with
RCA Bridged configuration, the loudspeaker is connected to both channels positive (+) output terminals.
Available power in this mode is four times the rated output of the amplifier, approximately 1000 watts
RMS into 8 ohms. Special care must be taken in connecting the input signal and loudspeakers to ensure
safe operation and best possible performance.
BALANCED/UNBALANCED SIGNALS
Balanced or unbalanced input options will depend on the type of signal available from your preamplifier or
other equipment. The Plinius SA-Reference provides both options to allow you to choose the most
suitable preamplifier for your purposes. Plinius Preamplifiers offer both balanced and unbalanced output
options.
BALANCED LINE is normally used to transmit signals in a professional environment. Because balanced
line effectively reduces or eliminates noise pick-up by the system cabling, it has become increasingly
more important in high-quality domestic high fidelity systems.
UNBALANCED leads such as single ended, RCA or coaxial are common and are used in the majority of
audio signal systems. The terminal plug and socket are most commonly called RCA and can be found on
your Plinius SA-Reference for use as the standard input terminals for both left and right inputs.
OUTPUT TERMINALS - STEREO
Output connections for the loudspeakers are provided on the left and right hand side of the rear panel.
Two parallel pairs of binding posts for each channel are fitted – these provide ease of use with bi-wiring
and multiple cables requiring a large contact area.

11
OUTPUT TERMINALS - BRIDGED/MONO
In bridged/mono modes, the loudspeakers utilise only the positive (+) outputs of your Plinius SA-
Reference. In this configuration power output to the loudspeakers is dramatically increased (around four
times as much), and is commonly used in conjunction with another amplifier for amplification of each
channel from the preamplifier.
Please note that in order to achieve STEREO performance in either of the Mono modes, it will be
necessary to use two Plinius SA-Reference Power Amplifiers - one amplifier each for left and right
channels.
MAINS SWITCH
This heavy-duty rocker switch in the centre of the panel turns the Mains/Line Power to the amplifier ON or
OFF. An LED in the centre of the front panel indicates that the power is on. When first switched on the
power LED will pulse for ten seconds - this is an initialisation sequence, after which the power LED
remains lit. The amplifier draws a moderately high current when switched on. Despite the "Soft Start
Circuit" within the amplifier reducing current demand on the mains as the amplifier is switched on, it is
not good practice to rapidly turn the Mains switch on and off repeatedly.
REMOTE TRIGGER TERMINALS
In order to integrate more effectively into a home theatre system, the Plinius SA-Reference has remote
trigger terminals fitted to the rear panel. By connecting a processor with a remote trigger signal to these
terminals, the SA-Reference can be put in and out of Class AB/mute by the processor to which it is
connected. When in Class AB/mute the amplifier draws less current and will operate at minimum
temperature. The output relays are also open, disconnecting the loudspeakers. This may be of advantage
in a multi-amplifier and/or remote installations. The Class AB/mute mode can only be activated via the
remote trigger terminals. Polarity of the connections to the remote trigger is not important.
GROUND LIFT SWITCH
This switch is located adjacent to the Mains Input Socket, and allows the signal ground to be
disconnected from the chassis. In some installations a hum loop may exist due to duplicate ground paths
from different equipment. Use this switch to remove the connection from 0V to ground thus allowing
some flexibility in your particular set-up. Note that in both XLR modes the ground lifting switch should
always be set to ‘chassis’.
MAINS POWER CORD IEC CONNECTOR
This connector is where the mains supply cable from your wall connects to the amplifier. You will notice
that a fuse holder is mounted within this connection, and it holds a mains fuse to provide surge and
overload protection for your amplifier.

12
INSTALLATION AND OPERATION
PLACEMENT AND VENTILATION
Your Plinius SA-Reference is designed to operate at a moderately high temperature, even more so when
used in Class A. The ideal location is on a rigid stand or floor mounted away from direct contact with any
temperature sensitive materials or deep pile carpets. The flow of air around the amplifier should also be
kept unimpeded, so ensure that the heat sinks (cooling fins) are not covered or restricted in any way to
ensure adequate ventilation.
The Plinius SA-Reference design incorporates a very high level of mechanical decoupling of the input and
output. It can however still be influenced by acoustical feedback in the operating environment. The use of
acoustic cones or a suitably spiked amplifier stand or table may further enhance the performance of this
amplifier. Consult your PLINIUS dealer for further advice if required.
MAINS VOLTAGE CONNECTION
Firstly check that the mains supply voltage printed on the rear of this amplifier is similar to the mains
supply voltage in your area. If in doubt, please consult your PLINIUS dealer.
Mains supply power connection is via the supplied plug-in lead. A standard IEC socket connects the
mains power at the amplifier end while a local mains plug is required at the wall end.
The wiring code used inside all Plinius product is:
Green to Earth/Ground
Blue to Neutral
BrowntoPhase/Live
Should a ‘local’ plug need fitting to the wall end of the lead, ensure that a suitably qualified or experienced
service technician wires the plug correctly.
IMPORTANT: DO NOT POWER UP YOUR AMPLIFIER UNTIL YOU HAVE CONNECTED
YOUR INPUT/OUTPUTS CORRECTLY FOR YOUR SYSTEM, (AS
EXPLAINED IN THE NEXT SECTION).

13
+
+
RIGHT OUTPUTS LEFT OUTPUTS
+
+
AMPLIFIER CONFIGURATION SELECTOR
REFER TO OWNERS MANUAL FOR USAGE INSTRUCTIONS
RCA STEREO
RCA BRIDGED MONO
XLR BALANCED MONO
XLR STEREO
RIGHT INPUTS LEFT INPUT
S
ALL MONO/BRIDGE OPTIONS USE RIGHT INPUT
AND LEFT + RIGHT+ OUTPUTS ONLY
INPUT/OUTPUT CONNECTION
REAR PANEL SHOWING LOCATION OF INPUT/OUTPUT TERMINALS
It is important that you connect your loudspeakers (outputs) and preamplifier (inputs) to the Plinius SA-
Reference Power Amplifier correctly to ensure the amplifier is not damaged, and sounds it’s best with your
system. Now that you have read and familiarised yourself with the connections on the back of the
amplifier as covered in the previous section, we will describe in detail the different ways in which you can
connect the amplifier to your system.
There are essentially four different ways that you can connect your system components to the Plinius SA-
Reference Power Amplifier:
1. RCA STEREO
2. RCA BRIDGED MONO
3. XLR STEREO
4. XLR BALANCED MONO

14
RCA STEREO
Connect your preamplifier or input signal to the two RCA inputs at the top of the amplifier back panel.
Make sure you connect the red coded cable to the red RIGHT RCA input and the black (or white) cable to
the black LEFT RCA input. Also make sure the RCA connectors are a snug fit and are inserted all the way
in.
Next connect your loudspeaker wires to the output posts on either side of the rear panel. Connect your
right loudspeaker (ie the one on the right of you when seated in your normal listening position) to the right
output terminals, ensuring that the red positive (+) terminal is connected to the red terminal on your
loudspeaker. Do the same with the black or negative (-) terminals.
Now turn the ACS switch fully clockwise so that it is in the RCA Stereo position. It is now safe to switch
on your amplifier.
RCA BRIDGED MONO
This option configures your amplifier to drive one loudspeaker from one unbalanced signal fed to the red
RIGHT RCA input. In bridged mono mode the only input made to your preamplifier is to the red RIGHT
channel RCA input. The black LEFT channel RCA input is not connected.
Next your loudspeakers are connected to both positive (+) channel output terminals. So the positive red
connection on your loudspeaker is connected to the red RIGHT amplifier output, and the negative black
connection on the loudspeaker should be connected to the red LEFT amplifier output. DO NOT CONNECT
ANYTHING AT ALL TO THE NEGATIVE (-) TERMINALS. MAKING A CONNECTION TO THE NEGATIVE (-)
TERMINALS OF THE AMPLIFIER IN THIS MODE CAN CAUSE SERIOUS DAMAGE!
You can still connect two loudspeakers using the lower positive (+) amplifier output terminals. This is
explained in the bi-wiring section following.
Now turn the ACS switch fully clockwise then one position counter-clockwise so that it is in the RCA
Bridged Mono position. It is now safe to switch on your amplifier.
XLR STEREO
Connect your preamplifier or input signal to the two XLR inputs at the top of the amplifier back panel.
Make sure you connect the RIGHT XLR input and LEFT XLR inputs to the right and left outputs from your
preamplifier respectively. Also make sure the XLR connectors click into place.
Next connect your loudspeaker wires to the output posts on either side of the rear panel. Connect your
right loudspeaker (ie the one on the right of you when seated in your normal listening position) to the right
output terminals, ensuring that the red positive (+) terminal is connected to the red terminal on your
loudspeaker. Do the same with the black or negative (-) terminals.
Now turn the ACS switch fully clockwise then two positions counter-clockwise so that it is in the XLR
Stereo position. It is now safe to switch on your amplifier.

15
XLR BALANCED MONO
As with RCA Bridged Mono, this option configures your amplifier to drive one loudspeaker, but from one
balanced line input connected to the RIGHT XLR Input. In balanced mono mode the only input made to
your preamplifier is to the RIGHT channel XLR input. The LEFT channel XLR input is not connected.
Next your loudspeakers are connected to both positive (+) channel output terminals. So the positive red
connection on your loudspeaker is connected to the red RIGHT amplifier output, and the negative black
connection on the loudspeaker should be connected to the red LEFT amplifier output. DO NOT CONNECT
ANYTHING AT ALL TO THE NEGATIVE (-) TERMINALS. MAKING A CONNECTION TO THE NEGATIVE (-)
TERMINALS OF THE AMPLIFIER IN THIS MODE CAN CAUSE SERIOUS DAMAGE!
You can still connect two loudspeakers using the lower positive (+) amplifier output terminals. This is
explained in the bi-wiring section following.
Now turn the ACS switch fully counter-clockwise so that it is in the XLR Balanced Mono position. It is
now safe to switch on your amplifier.
TERMINATION QUALITY
Quality of the connections must be examined to ensure that high performance trouble free operation is
enjoyed. Check that the connections are tight but do not over tighten. If bare wires are used make sure
that no loose strands of wire short cross the other terminals or the amplifier chassis. When using plugs
such as bananas, be sure to use good quality plugs with a firm fit.
BI-WIRING
Bi-wiring uses two pairs of loudspeaker cables for each channel loudspeaker. You will notice that the rear
panel of your Plinius SA-Reference has two pairs of output terminals for this purpose. When using bi-
wires in a STEREO installation, connect each wire pair to a corresponding pair of binding posts (one cable
to the top pair, one cable to the bottom) paying special attention to positive (+) red and negative (-)
black polarity. With a MONO setup remember that your speaker wires must use the red positive (+)
output posts ONLY. Connect one speaker cable to the top positive (+) red binding posts, and the other
speaker cable to the lower positive (+) red binding posts.

16
PHASING (OR POLARITY)
It is important to achieve good stereo imaging in your listening room. By observing the wiring
instructions above, each Power Amplifier/loudspeaker combination should be in phase. If you experience
poor stereo image and/or a lack of bass, check that the loudspeaker wiring has been connected correctly.
We recommend that you use one of the easily obtainable ‘test discs’ to help you ensure both phasing and
channel orientation are correct. If in doubt, consult your PLINIUS dealer for advice.
To achieve a sound performance that is correctly aligned to your room, make sure all of the leads carrying
signals for the RIGHT channel loudspeaker are connected to the RIGHT input to the amplifier from your
preamplifier or CD player etc. Signals for the LEFT channel should be wired in a similar fashion.
CONNECTING THE MAINS SUPPLY
Now that your Plinius SA-Reference Power Amplifier is configured to your system correctly, the mains
cable can be plugged into the IEC connector on the back of the amplifier. Turn on the power switch on the
rear panel. The power LED will pulse for ten seconds as the internal microprocessor and soft start
circuitry allow the amplifier internal voltages to settle. Once the amplifier is at full voltage the power LED
will stay lit, and the amplifier will be in mute. Press the mute switch to enjoy your new Plinius SA-
Reference Power Amplifier.

1
7
SA-REFERENCE FEATURES
ERROR DETECTION
The Plinius SA-Reference Power Amplifier has in-built error detection. This will function under the
following conditions:
• When the amplifier is overdriven/clipped
• If any internal fuse is damaged
Should either of these circumstances arise the amplifier will disconnect both channels and mute the input.
This condition will remain until the input signal level is reduced or the damaged fuse replaced. When
error detection is triggered the power LED will turn off and the mute LED will pulse. The internal error
LED (located towards the front of the circuit board in the top cavity of the amplifier) will also light.
FUSE PROTECTION
When any internal fuse is damaged one or more fuse warning LEDs will light. These LEDs are under the
amplifier lid located to the centre front of the main circuit board. Should any of the internal fuses need to
be replaced the base of the amplifier will need to be removed and the fuses located. The rail fuses are
near the middle of the circuit board. Replace them with the same type (10 amp normal blow).
IMPORTANT: DO NOT FIT A FUSE WITH A HIGHER RATING.
Please note that fuse failure may indicate a severe problem. Check all speakers and speaker cables for
damage/short circuit etc. Should the amplifier continue to exhibit rail fuse failure contact your PLINIUS
dealer.
ECOLOGIC CONTROL
The Plinius SA-Reference is also fitted with a microprocessor which monitors and performs the Bias and
Mute functions. It is programmed to switch the amplifier back into Class AB if no signal has been present
at the input for a predetermined time. This time can be adjusted to Off, 15, 30 or 60 minutes. During the
last minute without signal the bias LED will pulse to indicate the unit is about to return to Class AB. The
purpose of this function is to prevent the amplifier being left in Class A while unattended for a long period
of time.
To adjust this time constant the amplifier lid must be removed and the small jumper JP4 located on the
main circuit board at the front left shifted to the appropriately labelled pins. Please ensure that your
amplifier is switched OFF and disconnected from the mains supply before this adjustment is made. The
factory setting is 30 minutes.

18
LED BRIGHTNESS CONTROL
Your Plinius SA-Reference has an internal LED brightness control that will adjust all three front panel
LED’s. A small flat bladed screwdriver can be used to adjust the brightness. The LED brightness control
is a small multi turn potentiometer and is located on the front of the main circuit board within the top
cavity of the amplifier, and is labelled VR3. Make sure you adjust the correct potentiometer, and
remember to remove the mains supply from the amplifier before making any adjustments.
Ecologic Jumper JP1 Fuse LEDs Error LED LED Adjuster VR3
SECTION OF SA-REFERENCE MAINBOARD SHOWING POSITION OF
ECOLOGIC JUMPERS AND LED BRIGHTNESS ADJUSTMENT POTENTIOMETER
MAINS/LINE FUSE
A Mains/Line fuse is fitted within the IEC Mains/Line socket on the rear of the amplifier. A small drawer at
the bottom of this socket may be removed (after the IEC plug is removed) by levering it out with a flat
blade screwdriver. The fuse fitted should be rated at no greater than 20 amps normal blow.
In the unusual event that this fuse should blow, you must first establish the cause of this failure (such as
power surges, damaged mains cable etc.) before replacing the fuse with one of the same rating and type.
IMPORTANT: DO NOT FIT A FUSE WITH A HIGHER RATING.
TOWARDS
FRONT OF
AMPLIFIER

19
LOUDSPEAKER SELECTION
Your Plinius SA-Reference Power Amplifier is designed for use with high fidelity loudspeakers. It should
not be used to operate any other type of appliance or equipment.
Choice of loudspeakers is one of personal taste, providing the chosen loudspeakers are suitable for use
with your amplifier. Be certain that your loudspeakers can handle most of the rated output power of this
amplifier. You may find loudspeaker specifications confusing or misleading so you should discuss this
with your audio dealer prior to purchase. As a general rule, the use of high power (200 watt RMS or
greater) loudspeakers is recommended and desirable. However, our experience indicates that medium to
low power loudspeakers (100 to 200 watt RMS) are quite often suitable for use on this amplifier provided
the volume is maintained at a level where no distortion is audible.
Impedance of the loudspeaker load is important to ensure the rated performance of this amplifier. Any
combination of loudspeakers may be used but the total average impedance load for each channel should
be within a range of 4 to 8 ohms. Again, if you have doubts about the impedance of your loudspeaker
configuration, we recommend you speak to your PLINIUS dealer.

20
WHY CLASS A IS BETTER
Class A has always been regarded as the perfect operating mode for audio amplifiers. Many leading
amplifier designers and manufacturers world wide recognise that a well designed Class A circuit has
inherently lower distortion than any other design.
Class A circuit topology is one in which the total current the amplifier is capable of delivering, is kept
flowing in the circuit regardless of demand. In a conventional or Class AB amplifier circuit this current
flow varies when demand varies. Furthermore, as current varies, the voltage on the power supply rails (as
seen by the output stage) varies too. In a Class A circuit, current draw should be constant therefore there
is an absence of the power supply modulation common in Class AB design amplifiers. Pinpoint images,
tonal clarification, intertransient silence, more readily defined dynamic shadings, inner detail and authority
are all inherent advantages of good Class A design.