plusoptic MC-10G-SFP+-RJ45 User manual

Page 1
MC-10G-SFP+-RJ45
10G Copper to Fiber SFP+ Media Converter.
The PlusOptic MC-10G-SFP+-RJ45 is a 10G Media Converter that seamlessly connects 10G fibre and
copper signals via an SFP+ transceiver port and RJ45 port. This device offers a flexible 10G fibre to
copper solution with a reach of up to 100KM over singlemode fibre (dependent on the spec of the
SFP+ inserted into the device). This device features a 10Gbase Ethernet PHY chip that smoothly and
reliably connects two types of signal. The MC-10G-
SFP+-RJ45 can operate as a standalone unit or fit
into a 1RU Chassis.
The MC-10G-SFP+-RJ45 Converts:
•1000Base-T to 1000Base-X
•2.5GBase-T to 2500Base-X
•5Gbase-T to 5GBase-R
•10Gbase-T to 10GBase-R
Product Features
•Supports jumbo frame
•Can utilise both multimode and singlemode
SFP+
•Signal reach of up to 100km
•Can be used standalone or plug directly into a 19” chassis
•Supports DMI function for SFP+ fiber module
•Supports loopback test function
•Supports hot plugging
•Full state LED display
•Easy installation
•Provides reliable long-distance connection
•Fast connection with multi-function
•Small portable size
•Plug-and-play

Page 2
Technical Specifications
Standards
1000Base-T, 2.5GBase-T, 5Gbase-T, 10Gbase-T
1000Base-X, 2500Base-X, 5GBase-R , 10GBase-R
Media Supported
1000Base-T: Cat5 UTP/STP. MAX 100m;
2.5GBase-T: Cat5e UTP/STP. MAX 50m;
5GBase-T: Cat5e UTP/STP. MAX 50m;
10G Base-T: Cat6a UTP/STP. MAX 50m;
Port Type
1 x RJ45
1 x SFP Slot
Signals Converted
1000Base-T to 1000Base-X
2.5GBase-T to 2500Base-X
5Gbase-T to 5GBase-R
10Gbase-T to 10GBase-R
Power Supply
12V DC
Power
Consumption
MAX 5W
Operation Temperature
0℃to 55℃
Relative Humidity
5% to 80% (non-condensation)
Installing the Converter
For a standalone unit:
→ Verify the DC adapter conforms to your country DC power requirement and insert the power plug
→ Connect the media cable for network connection
For a slide-in unit:
→ The slide-in Media Converter and Converter Rack Chassis should supplied only from the same
source, both Media Converter Rack Chassis are built to match each other at dimension, DC jack, DC
receptacle and power safety.
→ Turn off the 19” converter rack power
→ Locate +12V DC power jack on converter back, carefully slide in and plug to 19” rack +12V DC
power receptacle
→ Connect the media cable for network connection
→ Turn on the converter rack power, the Power LED will light up

Page 3
Wire connection, Front and Side panel
Check List
Before you start installing the Converter, verify that the package contains the following:
---The TP-Fiber Converter
---AC to 12V DC Power Adapter (for external models) or Power Cord (for internal models)
---The User’s Manual
Please notify your local sales distributor immediately if any of the aforementioned items is missing or
damaged.

Page 4
LED Description
LED
Status
Description
PWR
On
Power is on and normal.
FX Link/Act
On
Connection status display for Fiber Link.
“ON” indicates that Fiber link is in correct
connection.
Blink
Active status display of fiber link.
“Blink” indicates packet goes through FX end.
SD
On
Fiber signal is detected.
10G
On
Transfer rate of electric interface is 10Gbps.
Off
Rate of electric interface is 10Mbps.
TX Link
On
Connection status display for electric link.
“ON” indicates that electric link is in correct.
TX Act
Blink
Active Status display of fiber link
“Blink” indicates packet goes through TX end.
Further Information
If you require any advice or further information, please do not hesitate to contact us on the details below:
Tel: [phone]
Email: [email protected]
Web: www.plusoptic.com