PMR NHSTH2C2XXX User manual
GETTING STARTED
Remove all components from the package. Items in the pack
include: Bluetooth headset with Ear Hook, Ear Cap, User Guide
and AC Charger. Please check the contents carefully and
contact your local dealer immediately if there are any shortages.
GETTING TO KNOW YOUR HEADSET
Please note some models of headset will differ slightly in style,
color and the functionality may vary according to their
specifications.
CHARGING YOUR HEADSET
Before using the headset, you must charge it for at least two
hours. When fully charged, the battery provides up to 8 hours of
talk time and up to 150 hours of standby time.
Please note that talk time is also a function of the mobile
phone and factory determined settings of the phone, so you
may find this figure is reduced under certain conditions.
To charge the headset
1. Plug the AC charger into the headset.
2. Plug the AC charger into a wall outlet. When the headset is
charging, the amber LED will light up.
3. When charging has finished, the amber LED will turn off or be
dim. Unplug the charger cable from both the wall outlet and
also from the headset.
Battery Indication: The amber LED can turn off after less than
2 hours charging; this normally indicates that the headset can be
used. However, for the initial charge, it is recommended that you
charge the headset for at least 2 hours in order to fully prepare
the battery for normal operation.
PAIRING THE HEADSET WITH YOUR MOBILE PHONE
Pairing is the process of linking the headset with your Bluetooth
mobile phone. Before you use the headset with your mobile
phone you must pair the devices. After this process has been
completed, you can use the headset only with its paired mobile
phone. If you wish to use the headset with a different mobile
phone, you must repeat the pairing process with the new mobile
phone. In this case, the headset will no longer work with the
original mobile phone. Please refer to the user manual of
your mobile phone for further information on ‘How to Pair’.
Typically, you need to make your phone ‘Discover’ the
headset by using a “Bluetooth”, “Connect” or “Setup”
menu then selecting an option to “Discover” other
Bluetooth devices.
To pair the devices
1. Before you pair the headset, ensure that the battery is fully
charged. If the headset battery is low then amber LED will flash
2. Set up your mobile phone to “Discover” your headset.
3. With the headset turned off, press and hold the Talk button
for about 7 seconds until the blue and amber LEDs flash
alternately or until you will hear the “PAIR” tone (the second of
two tones).
4. Release the Talk button. The headset is now in Pairing
Mode.
5. Initiate the device discovery feature on the mobile phone.
Refer to the mobile phone user guide for instructions for
initiating this feature.
6. When prompted by the mobile phone, enter the headset pin
code which is 0000. When pairing is complete, the blue LED on
the headset will flash at three-second intervals and the headset
will be placed in standby mode, ready to make and receive
calls.
If disconnection or a lost link occurs, it may be due to the
following reasons:
a) The range is over 10 metres between the headset and the
mobile phone.
b) The mobile phone disconnected the link to conserve power
or enable another function.
c) Either device has been switched off.
Note: The headset, in normal operation, should maintain the
connection with the mobile phone at all times once pairing has
been successful and a connection has been established
between the two devices.
To cancel pairing mode - While the headset is in pairing mode,
you can cancel the pairing process and turn off the headset.
Press and hold the Talk button for approx. 3 seconds. You will
hear an “OFF” tone, the Amber LED will flash several times and
the headset will turn off. Release the Talk button.
FITTING THE HEADSET ON YOUR EAR
The Headset is designed to fit comfortably in your ear. The
ear hook can be fixed into the headset from both sides,
allowing you to position on right or left ear. The ear hook can
BLUETOOTH
TINY HEADSET
P/N NHSTH2C2XXX
USER GUIDE
Declaration of Conformity.
We declare that product NHSTH2C2XXX conforms to
the R&TTE Directive 1999/5/EC .
be separated from the Headset by simply pulling the base of
the ear hook away from the main body of the Headset. The
ear hook can then be reinserted in the other direction for
positioning on the opposite ear. The ear hook is flexible and
can be bent to adjust the fit that is best for the individual user.
To replace the ear cap - Stretch the rubber ear cap around
the end of the speaker until secure.
To place the headset on your ear - Place the headset
speaker in your ear with the microphone angled towards your
mouth. The headset should fit snugly in your ear.
SWITCHING ON YOUR HEADSET
To turn on the headset - With the headset turned off, press and
hold the Talk button for about 5 seconds until you hear the “ON”
tone (two ascending “beeps”) or you see the Blue LED start to
flash. Release the Talk button. The headset will turn on and enter
standby mode, ready to make and receive calls. After turning on
the headset, the headset will try to connect to the last
paired/connected device automatically.
To turn off the headset - With the headset turned on, press and
hold the Talk button for approx 3 seconds. You will hear an “OFF”
tone (two descending “beeps”) and the Amber LED will flash
quickly several times. The headset will turn off and you can
release the Talk button.
MAKING CALLS
You can make calls from your mobile phone, or directly from the
headset using voice dialing commands (if this feature is supported
by your mobile phone).
To make calls from your mobile phone - Dial the call from your
mobile phone. Dependent on your mobile phone settings the call is
automatically connected to your headset.
To make calls using VOICE DIALING (if supported by your
mobile phone) - Click the Talk button on your headset. You will
hear a Voice Dial tone possibly followed by the voice-dial prompt
tone from your mobile phone. Speak the name of the person you
wish to call. The call is automatically connected to your headset.
To make calls using LAST NUMBER REDIAL (if supported by
your mobile phone) - While in standby mode, press and hold the
Volume DOWN “-” button for about 3 seconds, and you will hear a
“Last Number Redial” tone (single beep); Release the Volume
DOWN “-” button, the call is automatically connected to your
mobile phone.
RECEIVING CALLS
You must configure your mobile phone to answer calls directly on
your Bluetooth headset. Refer to the mobile phone user guide for
instructions on initiating this feature.
When you hear your headset ring, press the Talk button on the
headset. The call is automatically connected to your headset.
Reject calls Please note you can also reject calls by depressing
the Talk button for about 3 seconds. You will also hear a beep in
addition to the incoming ringing when the call reject is about to
occur (Not all phones support this feature).
ENDING CALLS
When you have finished your call, press the Talk button on your
headset. The call will be disconnected.
TRANSFERRING CALLS
You can transfer calls connected to your headset back to your
mobile phone, or from your mobile phone to your headset. (Not all
phones support this feature)
To transfer calls from your headset to the phone press and hold
the Volume UP button for about 3 seconds until you hear the tone.
To transfer from phone to headset either press and hold the
Volume UP button again or (especially on Nokia phones) you may
need to click the Talk button to get the call.
ADJUSTING THE VOLUME
To increase the volume - While on a call, press and release (click)
the Volume UP button “+” to increase volume by 1 step. Repeat
this procedure until you have reached the desired level.
To decrease the volume - While on a call, press and release
(click) the Volume DOWN button “-“ to decrease volume by 1 step.
Repeat this procedure until you have reached the desired level.
MUTING THE HEADSET
You can mute and un-mute the microphone temporarily so that
you cannot be heard by the connected party.
To mute the headset – While on a call, press and hold both the
Volume UP button “+” and the Volume DOWN button “-” at the
same time for about 3 seconds. You will hear a MUTE tone
(Single beep), the microphone is muted.
To un-mute the headset - When microphone is muted, press and
hold both the Volume UP “+”button and Volume DOWN “-” button
at the same time for 3 seconds. You will hear the MUTE tone
(Single beep), the microphone is un-muted.
VISUAL INDICATORS
Visual Indicators - 2 LEDs (blue and amber) indicate the status of
the headset:
Status Indication
Battery 2/3 full Amber LED is off or dim
Battery low Amber LED on instead of Blue LED
Headset off All LEDs are off
Headset in standby
mode, ready to make &
receive calls
Blue LED flashes at 3 second
intervals
Headset in pairing
mode
Blue and amber LEDs flash
alternately.
TROUBLE SHOOTING
Please note that you should also be familiar with the operation of
your mobile phone and how to connect to Bluetooth devices.
Please read your mobile phone user guide carefully. Please note
that the Bluetooth headset will only work with Bluetooth mobile
phones. For operation with a PC or laptop device please note that
these devices should also be Bluetooth enabled with appropriate
third party software in order to enable correct operation.
Symptom/Problem
Solution
When Talk button is
pressed, no LED
indicator
•Unit not charged
•Consult authorized dealer
Headset powers on
with blue LED flashing
but no connection to
mobile phone
•Check unit is paired to phone.
Check settings in phone. Headset
default name is BTHS
•Check phone is switched on
•Check handsfree settings for
phone
•Ensure headset & phone are
within range
Headset does not
charge
•Check mains charger adapter is
connected to the headset
securely & is switched on
•Check AC charger is working
using another device
•Consult authorized dealer
CUSTOMER SERVICE INFORMATION
In addition to the troubleshooting table on the this page you can
get support on the PMR support forum at this web address
http://www.esktech.com/forums/
For other PMR Bluetooth products or support, please view our
website – www.pmr-technology.com or email
A copy of the Declaration of Conformity is available in the products
section on our website www.pmr-technology.com
DISCLAIMER
While every effort has been made to ensure that the information in
this manual is accurate and complete, no liability will be accepted
for any errors and/or omissions made. The manufacturer reserves
the right to make changes and improvements to the specifications
and features of the hardware and firmware of the products
described in this document without prior notice. Reproduction,
transfer, distribution or storage of part or all of the contents in this
document in any form is prohibited without prior permission of the
manufacturer. All trademarks acknowledged. The product is
Bluetooth qualified by Nolan Systems.
QSGPMRTINYHSVer20
