PNI Wayfinder V2000 User manual

OPERATION MANUAL
V2000
DIGITALVEHICLECOMPASS

Making Ordinary Products Extraordinary

1
You have purchased one of the most sophis-
ticated compasses available for use in a
vehicle. The Waynder V2000 is one of sev-
eral models using our latest technology to
make a digital compass easy and fun to
use, while still incorporating patented mag-
netic sensor technology to give you accurate
compass headings. PNI’s magnetic sensor
technology electronically measures your
vehicle’s magnetic eld and calibrates for
inaccuracies mathematically with its built-in
microprocessor. The result is unequaled com-
pass performance in a vehicle environment.
Features
• Patented magnetic sensor technology
same as the built-in compasses in GM,
Ford, and Chrysler vehicles.
• Bearing point stores one compass heading
at a time in memory to stay on desired
course.
• Inside or outside temperature in either
Fahrenheit or Celsius with temperature
sensor installed.
• ICE alert feature warns the driver to icy
road conditions when the temperature
sensor is installed outside.
CONGRATULATIONS!

2
• Automatic shut-off when no magnetic
eld changes have been sensed for
approximately 10 minutes.
• Programmable automatic backlight shut-
off feature.
• Photo diode light sensing feature turns
the backlight on or off depending on the
amount of ambient light when used with
12-volt adapter.
• Distortion warning when magnetic inter-
ference from outside sources is affecting
compass accuracy.
• Holographic LCD improves brightness
and contrast while removing glare.
• One-year warranty.
FEATURES

3
The manual is designed with procedures
organized in the order that they will be needed.
Additional information about procedures or
compass use can be found in our Frequently
Asked Questions section.
1. The LCD icons are written in capital
letters surrounded by quotes.
2. Buttons are indicated by a graphical icon
of each button, such as .
3. Procedures are organized so that the
action to perform follows the step
number and result of that action is
italicized.
4. “Press” means quickly press and release a
button in less than two seconds.
5. “Hold” means press and hold the button
for at least two seconds, or until a display
appears.
6. Indicates a warning or important
information.
7. Indicates a feature or optional equip-
ment available at additional cost.
CONVENTIONS USED IN THIS MANUAL

4
Display . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Waynder V2000 . . . . . 7
Installing the battery . . . . . . . . . . . . .7
Installing the 12-volt adapter . . . . . .8
Installing the temperature sensor . . .8
Adjusting the mounting bracket . .10
Calibration . . . . . . . . . . . . . . . . . . . . . . 13
Bearing point mode . . . . . . . . . . . . . . 14
Temperature mode . . . . . . . . . . . . . . . 15
ICE alert feature . . . . . . . . . . . . . . . .16
Backlight mode . . . . . . . . . . . . . . . . . . 17
Photo diode feature . . . . . . . . . . . . .18
Optional accessories . . . . . . . . . . . . . 19
Frequently asked questions . . . . . . . 20
Service and replacement . . . . . . . . . . 24
Limited warranty . . . . . . . . . . . . . . . . 26
CONTENTS

5
DISPLAY
“DISTORTION” Cardinal Point Numeric Heading
Icon Readout Readout
Compass Rose Temperature and Buttons
Bearing Point Readout
Compass Front
Battery Photo Diode
Compartment
Temperature 12-Volt Power
Sensor Jack AdapterJack
Compass Back

6
When turned on, the unit displays heading in
one of 16 cardinal points (N, NNE, NE, ENE,
etc.), numeric digits with a resolution of 5°,
and a compass rose at all times. The compass
rose points in the direction displayed on the
cardinal point readout.
Buttons and icons
Light button
Press to turn the backlight on or off or
hold to set the backlight auto shut-off value.
Cal button
Press or hold to begin calibration process.
Temp button
Press to display the temperature or
hold to program the display for Fahrenheit
or Celsius values.
Point button
Press to display a stored bearing point
or hold to store a new bearing point.
Power button
Press to turn the Waynder V2000 on
or off.
“Distortion” icon
The “DISTORTION” icon displays when mag-
netic interference is compromising compass
accuracy or when a battery has been change.
DISPLAY

7
Step 1: Installing the battery
The unit uses a 3-volt CR123A lithium-type
battery, installed according to the diagram
on the inside of the battery compartment.
Push the battery straight down into the
compartment, not at an angle. To remove,
open the battery compartment.
Once the battery is inserted, the unit will cycle
through a quality test of two different displays.
The entire test lasts approximately 10 seconds,
then displays heading information. If any
of the two quality test screens display for
more than 30 seconds, remove the battery,
wait for approximately one minute, and then
reinsert the battery. Whenever the battery is
changed or removed, the V2000 will need to
be recalibrated.
The Waynder V2000 has an auto shut-off
feature. When no magnetic eld change has
been detected for approximately 10 minutes,
the compass automatically switches off and
saves all settings. No magnetic eld change
implies that the car is parked.
After installation, you must calibrate the
unit. As a reminder, the “DISTORTION”
icon will display in the upper left corner
until the unit is calibrated.
INSTALLING THE WAYFINDER V2000

8
Step 2: Installing the 12-volt adapter
Installing the 12-volt adapter is optional, but
recommended. Insert the small end into the
jack marked “POWER”, located on the back of
the compass and plug the large end into your
cigarette lighter receptacle.
Since cars do not always have constant
power supplied to the lighter receptacle,
you must keep a battery in the Waynder
V2000 at all times to allow the unit to
keep memory settings.
A 15-foot hardwire kit is available at
additional cost. See Optional Accessories
Step 3: Installing the temperature sensor
The included temperature sensor and tether
may be used outside or inside the vehicle.
Sensor placement inside the vehicle should
be somewhere out of direct sunlight and
away from your vehicle’s ventilation system,
where there is natural airow to the sensor.
Sensor placement for outside temperature
should also be away from direct sunlight and
engine heat in a place where there is natural
air ow to the sensor, such as in the grill
area or door jamb. Every vehicle is different,
making it impossible to list all possible sensor
locations.
INSTALLING THE WAYFINDER V2000