Pocket home PH-SP1 User manual
Version 11.02
Wireless receiver for control of
electric heating devices
- UNDER THE SWITCH -
PH-SP1
Operating instructions
Control of electric heating systems
Component of the PocketHome®system
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched
according to the required temperature
The control unit PH-BSP is the pilot component
ph_sp1_en:Layout 1 18.3.2011 13:18 Page 1
INSTALLATION
The device can only be installed by a person with adequate
qualification! The installation must be executed in
a voltage-free state!
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
LN
FUNCTION BUTTON ( R ) :
SHORT PRESSING (for
about1,5s) -coding.
LONG PRESSING (for about 5s)
-RESET deleting the code from
the memory (the green and red
LEDs flash simultaneously).
PH-SP1 is used for switching the heating device in connection
with the PH-BSP control unit. The big advantage is mounted
directly into the
installation box.
ph_sp1_en:Layout 1 18.3.2011 13:18 Page 2
1. Switch off the main circuit breaker.
2. Connect the receiver acc. to the diagram.
3. Switch on the main circuit breaker; the green diode
flashes on the receiver; thus the receiver is ready for
further setting.
4. Shortly press the FUNCTION BUTTON for about
1.5 s (the green and red diode are flashing alternately).
5. On the PH-BSP control unit, press the “Test” button in
the ACTIV mode to activate the SP
switching components (see page 10
of the PH-BSP instructions).
6. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
LED 2
LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the transmitter
within approx. 6 hours, it switches to the 2-min-ON /
8-min-OFF mode). LED flashes only if the relay is on,
i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION
ACTIVATION PROCEDURE
INDICATION DIODES
ph_sp1_en:Layout 1 18.3.2011 13:19 Page 3
8 594012 221864
CERTIFICATE OF GUARANTEE
(guarantee period for the product amounts to 2 years)
product No.: date of sale:
stamp of shop:
examined by:
In case of guarantee or
post-guarantee service,
send the receiver to the
manufacturer’s address.
DECLARATION OF CONFORMITY
We, ELEKTROBOCK CZ s.r.o., herewith declare that our product PH-SP1 is in
conformity with the basic requirements and other respective provisions of the
directive 1999/5/ES. Issued: 1.09.2008
TECHNICAL PARAMETERS
Power supply 230 V/ 50 Hz
Communication type two-way
Frequency 433,92 MHz
Sensitivity < -92 dBm
Range 150 m (in free area), 20 m (in built-up area)
Output relay, max.16A/ 250 VAC
Protection IP20 and higher acc. to the installation
Working temperature 0 to 40°C
Dimensions (LxWxD) 49,5 mm x 45,5 mm x 26 mm
in compliance with RoHS
Pb
LEAD FREE
MADE IN CZECH REPUBLIC
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel./fax: +420 541 230 216
http:// www.elbock.cz
PH-SP1 is suitable for switching heating panels, direct heaters,
radiant panels, heating mats, etc. It switches the connected
device according to the information received from the control unit.
To be installed in internal rooms. Do not locate near power lines!
ph_sp1_en:Layout 1 18.3.2011 13:19 Page 4
Table of contents
