POLA HP33 User manual

How to connect the wind meter
Connect the wind meter provided as shown in
the diagram. For remote connections use a
standard 0.5-square millimeter two-pole wire ,
taking great care over the connections, by
insulating and sealing the joins carefully.
INSTALLATION
How to connect the line
Connect line on terminals L-N; protect supply
with adeguate fuse.
How to connect the contacts
Connect terminals on the terminal block
(contacts up to 4AMP.AC1).
HP33 can be connected with N.2 WX wind probes in order to control the 2 sides that are
in contact with the wind of the environment that it has to control.
It is possible to know the speed of the wind in only one direction, but with 2 different sets.
To obtain this, connect WX on 9-10 terminals and connect 9-11 e 10-12 terminals.
HP33
Wind Surveyor
SL 3.0
Handbook
WIND 1 SETTING.
Press WIND 1 (key lamp flashes):
This message will be displayed instead of the
Set Wind Speed meter 1 (*1).
Press + or - to modify. Press WIND 1 to confirm.
WIND 2 SETTTING.
Press WIND 2 (key lamp flashes):
This message will be displayed instead of the
Set Wind Speed meter 2 (*1).
Press + or - to modify. Press WIND 2 to confirm.
ALARM TIME SETTING.
Press TIME (key lamp flashes):
This message will be displayed instead of the
Set wind Speed alarm time (in seconds).
Press + or - to modify. Press WIND 1 to confirm. (*2).
(*1) Unit representation of wind is selected in COSt, and indicated from UNIT lamp.
(*2) This time represents the minimum time (in seconds) of alarm duration.
Speed value displayed are just indication.
MAIN SETTINGS (Run Mode)
The HP33 wind meter gives only an approximate indication of the wind speed.
We do not recommend to use it in every application where the wind speed can
be a critical factor and do not take any responsability for any losses or injuries,
costs or damages arising from wind speed.
As it company policy to continually improve the products the Manufacturers
reserve the right to make any modifications thereto without prior notice. They
cannot be held liable for any damage due to malfunction.
07.05.13
230V LINE *
N.O. CONTACT
WIND 1
N.C. CONTACT
WIND 1
N.O. CONTACT
WIND 2
N.C. CONTACT
WIND 2
WX WIND PROBE 1 WX WIND PROBE 2
HP33
*Other power voltage if you required.

*2) Time (in seconds) overcome SET for entry in alarm condition.
*3) Time (in seconds) sampling wind speed; for low value can read a quick change of
*1) HP33 can be configurated in these different wind meter representation:
0 : Km/h wind speed range (max 100).
1: m/sec wind speed range (max 30).
2 : Knots wind speed range (max 60).
3 : RPM wind speed range (max 5000).
These settings refer to the operation mode of the system and must be made on
initial startup. Press - / + at the same time for at least one second: the message
C.O.S.t. will be displayed.
Press than repeatedly TIME until the message regarding the chosen variable is
displayed (see table below) : value of variable and message will be displayed.
Press + or - to set a new value and then press TIME to confirm.
The next system constant will then appear.
You can press TIME for at least 2 seconds to exit and return to the Run Mode.
COSt PROGRAMMING (System constants)
wind speed on display,
AL.OFF
AL.ON
SPEED 1 SENSOR
C on d it i on at e d
by Minimu time
gust o f wi n d
(t.rit)
Conditionated by
Minimum time of
al ar m durati on
t.dur .AL.OFF
AL.ON
SPEED 2 SENSOR
C on d it i on at e d
by Minimu time
gust o f wi n d
(t.rit)
Conditionated by
Minimum time of
al ar m durati on
t.dur .
OPERATING DIAGRAMS
Mess. Value Meaning Note
tYPE 0 Wind speed representation *1
t.rit 2" Minimum time (in seconds) gust of wind *2
rEAd 1" Integration time (in seconds) wind reading *3
n.CAL =2 Number of impulses of WX sensor
VIEWING WIND SPEED RECORDING
Press WIND 1 together with + : will be displayed followed
by Maximum Wind Speed 1.
Values are permanently stored in the memory: for deleting all values in the memory keep
pushed + key for more than 3 seconds: CLEA message will appear on display before
clearing operation.
Press WIND 2 together with + : will be displayed followed
by Maximum Wind Speed 2.
The light situated at the bottom of the display shows the state of the controller:
STATE INDICATION LAMPS
Speed value displayed are just indication.
Lamp. State N° Relay Contacts
DANGER 1 Zone 1 Alarm On 1 3-4-5
DANGER 2 Zone 2 Alarm On 1 6-7-8
Km/h Km/h representation
m/sec m/sec representation
Knots Knots representation
WIND SPEED REPRESENTATION
ALARM 1 ON ALARM 2 ON
This processor is already programmed with the following (variable) settings.
To return to these settings at any time you may:
Power off the processor, press TIME key and keep it pressed giving power on:
boot message will be displayed (release now TIME key).
SEt.1=30.0u SEt.2=30.0u t.dur=60" .
The COSt values are shown in paragraphs 1.2
PRESET PROGRAMS
MANUAL MODE
In some start-up conditions may be useful to work in "manual" mode:
Power off the processor, press + key and keep it pressed giving power on:
HAnd message will be displayed (release now + key).
Push + until is displayed number required to be handed (see table State
indication lamps ) and push TIME for activing relay.
Pushing again + for increase relay number previous relay is disactivated.
You can press TIME key for a least two seconds to escape and return to the Run Mode.