Polk Audio AB510 User manual

SYSTEM PLACEMENT
The Polk AB Series Loudspeaker Systems are designed to provide supe-
rior sonic performance without intruding on the design of your living
space. The design goals were to create open, three-dimensional sound
and smooth, accurate frequency response in an easy-to-install chassis.
Placement of the system in a room bears careful consideration, as the
installation is permanent. The AB510 and AB710 loudspeakers can be
mounted on almost any wall or ceiling. Keep in mind that placing the
loudspeakers at least 6-8 feet apart and away from room edges or cor-
ners will result in better stereo imaging.
As ceiling mounted speakers point downward and are closer to the lis-
tener than most wall-mount positions, it is sometimes advisable to use
more than one pair to get even distribution of sound. Intended uses,
ceiling height, room size, and listening position all play a part in
determining how many pairs should be used. In an average size room
with 8' ceilings we recommend using 2 pairs of ceiling-mounted
loudspeakers. Your Polk Audio dealer can help you make the right
choice for your room.
If your speakers are used in an outdoor installation, the best location is
one that provides shelter from rain and other outdoor elements. The
most common and ideal location is under an eave of your house facing
downward. If you position the AB loudspeakers where water will directly
contact them, it is advisable to use a sealant or caulk between the
frame of the loudspeaker and the wall surface. This seal should prevent
water from getting behind the loudspeaker and wall surface. Do not
position the loudspeakers where water can pool on the surface of the
woofer cone or tweeter dome. This will greatly decrease your speaker’s
useful life.
A WORD FROM MATTHEW POLK
Dear Music Lover,
Thank you for purchasing Polk Audio speakers. Designing and building
speakers is more than just a business for the people of Polk Audio –
it is our passion. We are all dedicated to your complete satisfaction
and delight.
Your new Polk speakers include the latest loudspeaker technology to
assure outstanding performance and unmatched quality. Please take a
moment to read through this manual for information on getting the
greatest enjoyment from these fine instruments.
We make a wide variety of main, center, rear channel, powered sub-
woofer, and accessory speakers so you can assemble a complete and
well matched high-performance surround sound system. If you would
like more information on building the Polk system of your dreams, con-
sult your Polk Audio dealer or call our Customer Service Department. In
North America call [phone], Monday through Friday, 9:00am
through 6:00pm Eastern time.
Sincerely,
Matthew S. Polk
Chairman and Co-Founder
P.S.: A wealth of information can also be found on our award-
winning web site: www.polkaudio.com.
AB SERIES
AB510
AB710
Instruction
Manual

PAINTING THE SPEAKERS
The Polk AB Series Loudspeakers can be painted to fit your decorating
tastes. Paint the speaker frames before assembling them. The grilles
and frames should be painted separately. Grille – Either hang the grille
in free space or place it on paper before painting. The grilles must be
sprayed – do not use a brush or roller – Spray two or more thin
coats rather than one thick coat to avoid clogging the perforations of
your metal grilles, which can impair performance. If you are using an
interior paint, it should be thinned before spraying.
LISTENING LEVELS AND AMPLIFIER CONNECTIONS
Our AB Series Loudspeakers are highly efficient systems and will easily
achieve high listening levels with moderate amounts of power.
Remember that the greatest chance of damage to any speaker occurs
when the amplifier, regardless of size, is overdriven. Surprisingly, the
possibility is usually greater with small amplifiers than with larger ones.
If the sound becomes harsh and steely in character, then you may be
pushing your amplifier into “clipping” mode. Amplifier clipping creates
undesirable high frequency energy and runs the risk of tweeter damage.
Regardless of amplifier size or speaker power rating, when you turn the
volume control past the point where distortion becomes audible you are
risking damage to both the speaker and amplifier.
IMPORTANT—Proper polarity is essential to the Polk AB series. The
positive terminal on the driver is designated with a plus(+). It must be
connected to the positive(red) terminal on your amplifier. The other ter-
minal, designated with a minus(-) must be connected to the
negative(black) terminal of your amplifier.
Use the pigtails to connect your speaker wire to the loudspeakers. You
may use a wirenut, solder, or twist and tape to connect the two wires.
Take special care to ensure a clean, positive connection. Make sure that
the connections are insulated from touching any other metal or each
other.
WIRING CONSIDERATIONS
As with the mounting locations, the wire routing is permanent, and so
demands special attention. The following recommendations will help you
make the best decisions in selecting and installing the wire used to con-
nect the loudspeakers to the amplifier.
Wire Recommendations
Wiring inside your walls or ceiling should be done before or in conjunc-
tion with installation of your in-wall speakers. Wire meeting appropriate
building and fire codes must be used. Use at least 18 gauge wire or
heavier. Wiring is best performed by a licensed professional.
Routing the Wire
It is beyond the scope of this manual to address all possible situations,
but certain basic rules should be followed:
1.) The wiring scheme you choose is determined by the number of
units you are installing, the way you wish to distribute the sound,
the amplifier you have chosen, and degree of flexibility you wish to
provide in your system.
2.) The wire run lengths should be kept as short as possible.
If runs over fifty feet long are necessary, heavier gauge wire
is recommended.
3.) Avoid routing speaker wires near house electrical cables. If this
cannot be avoided, try to make the speaker wires cross the power
cable at right angles.
4.) Try to avoid routing the wires against sharp objects, particularly
plumbing or electrical fittings.
5.) Allow about two feet of free wire at the wall cutout to facilitate
installation of the loudspeaker.
TOOLS NEEDED
•Pencil and template for marking cutout
(template is part of packaging insert)
•Keyhole saw and/or utility knife for cutting
mounting opening
•No. 2 phillips head screwdriver
•Wire strippers
•Sharp pointed metal device, such as ball point pen,
paper clip, or metal scriber for lifting off the grille
INSTALLING IN EXISTING CONSTRUCTION
Your Polk AB Loudspeakers have been designed for easy installation.
If you intend to do the installation yourself we assume that you possess
some skill in the proper use of hand and power tools. You should have
a thorough understanding of local building and fire codes and a
familiarity with the area behind the wall or ceiling where the speakers
will be installed.
If you are not accustomed to working on your walls or ceiling, the time
to get help is before you start cutting. There must be at least one inch of
clearance between the cutout and any studs or joists in order for the
mounting hardware (dogs) to place themselves properly. Wall studs are
spaced on 16 inch centers in most parts of the country, but actual spacing
should be verified.
Your AB’s require a mounting depth of at least three inches measured
from the face of the wall; they can be installed in walls faced with
paneling as little as 5/16" thick or plaster-on-lath as thick as two inch-
es. For acoustical considerations you may wish to insulate the area
behind the speaker loosely with a small amount of fiberglass batting or
dacron to reduce the potential problem of sound transmission into an
adjoining room.
For more information visit our web site at http://www.polkaudio.com

Once you have determined the exact placement of your speakers and the
templates are in position on your wall or ceiling, you are ready to cut
your mounting hole:
1.) Select locations for both of your loudspeakers.
2.) Check locations for interference from studs, pipes, wiring etc.
before cutting.
3.) Use the template (supplied in packaging) to scribe the mounting
holes.
4.) Cut mounting holes.
5.) Fish wires from amplifier (leave at least two feet slack).
6.) Secure cables to the wall, ceiling or a stud with cable tie or
tape.
7.) Make sure mounting screws are extended adequately for wall
thickness, fold clamps in towards chassis and place the baffle in
the mounting hole.
8.) Tighten all three mounting screws. Clamps will rotate into place
as you tighten.
9.) Connect the speaker wires to the pigtails with wire nuts
or solder. Use electrical tape to protect connections. Connect
pigtails to loudspeaker matching amplifier positive and negative
terminals to plus(+) and minus(-) terminals
on loudspeaker.
10.) Install the loudspeaker into the baffle with 4 supplied screws.
Install the grilles.
Removal after Installation
If it should ever be necessary to remove the AB Series Loudspeaker
from the wall, you must first remove the loudspeaker from the baffle.
Loosen the mounting screws just enough to allow the dogs to rotate out
of the way of the chassis.
INSTALLING IN NEW CONSTRUCTION
A rough-in kit is available separately to facilitate installations in open
framed walls and ceilings. Instructions and suggestions are provided
with this kit.
TROUBLESHOOTING
1. No sound from speakers.
•Check all amplifier connections and connections to speakers.
•Make sure amp is connected to AC outlet and
switched on.
2. Distortion at very high listening levels.
•Listen at lower levels.
•Purchase larger amplifier.
3. Not enough bass.
•Make sure speakers are in phase.
TECHNICAL ASSISTANCE
If you have any questions or problems with your loudspeaker system,
please do not hesitate to contact your authorized Polk Audio dealer from
whom you purchased your loudspeakers. Your Polk Audio dealer has the
experience needed to pinpoint any problems that may exist and has easy
access to technical information from the Polk Audio factory. If you
need assistance or information on other Polk Audio loud-
speakers for your home or car, call 1-800-377-7655.
For more information visit our web site at http://www.polkaudio.com
INSTALLING IN EXISTING CONSTRUCTION
CLAMP WILL
ROTATE AS YOU
TIGHTEN.

5601 Metro Drive
Baltimore, MD 21215 USA
[phone]
http://www.polkaudio.com
“Polk”, “Polk Audio”, “The Speaker Specialists” and “Dynamic Balance” are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated.
AB710
Driver Complement:
6.5" (165mm) polymer laminate midwoofer
.5" (12mm) polymer dome tweeter
Overall Size:
8.125" (207mm) round
Cutout Size:
7.25" (184mm) round
Mounting Depth (less wall thickness):
3.135" (79mm)
Overall Frequency Response:
40 - 20,000 Hz
-3dB Limits:
58 - 18,000 Hz
Recommended Amplification:
5 - 100 watts / channel
Nominal Impedance:
Compatible with 8 ohm outputs
Sensitivity:
88 dB @ 1 watt / 1meter
AB510
Driver Complement:
5.25" (133mm) polymer laminate midwoofer
.5" (12mm) polymer dome tweeter
Overall Size:
8.125" (207mm) round
Cutout Size:
7.25" (184mm) round
Mounting Depth (less wall thickness):
1.525" (39mm)
Overall Frequency Response:
60 - 20,000 Hz
-3dB Limits:
78 - 18,000 Hz
Recommended Amplification:
5 - 75 watts / channel
Nominal Impedance:
Compatible with 8 ohm outputs
Sensitivity:
88 dB @ 1 watt / 1meter
AB SPECIFICATIONS
RM0451-1
POLK AUDIO LIMITED WARRANTY
Polk Audio, Inc. warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the “Product”) will be free from defects in materials and workmanship
for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically terminate prior to
the expiration of the five (5) years if the original retail purchaser sells or otherwise transfers the Product to any other party. The original retail purchaser shall here-
inafter be referred to as “you.” To allow Polk Audio to offer the best possible warranty service, please fill out the Product Registration Card(s) and send it to the Factory,
at the address provided on the Product Cards(s) within ten (10) days of the date of purchase.
Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio Authorized Dealer from whom you purchased the Product, or to
the Factory at the address given on this manual. Products must be shipped in the original shipping container or its equivalent; in any case the risk of loss or damage in
transit is to be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship
at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no additional charge, except
as set forth below. All replaced parts and Products become the property of Polk Audio. Products replaced or repaired under this warranty will be returned to you, within
a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly attributable to defect in materials or workman-
ship, or service, repair, or modification of the Product which has not been authorized or approved by Polk Audio. This warranty shall terminate if the Serial number on
the Product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. If this Product is defective in materials or workmanship as warranted above, your sole remedy shall be repair
or replacement as provided above. In no event will Polk Audio, Inc. be liable to you for any incidental or consequential damages arising out of the use or inability to use
the Product, even if Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some
states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you.
All implied warranties on this Product are limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an implied Warranty lasts,
so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state.
This Warranty applies only to Products purchased in the United States of America, its possessions, and U.S. and NATO armed forces exchanges and audio
clubs. The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio AuthorizedDistributors in
such countries.
Note: Specifications are subject to change without notice.