POLTI AS 530 User manual

®
1
2
2a
3
4
5
16
7
14 17
11
10
9
18
8
6
13
12
15
17
A
A1
C
D
EE1
F
H
IL
E2
Fig.1 Fig.2
Fig.3 Fig.4
Fig.5 Fig.6
19
Fig.7
17

KEY
1) Dust collection container
2) Dust container handle
2a) Dust collection container emptying buttons
3) Dust container top lid
4) Top lid opening button
5) Hose connector
6) Carry handle
7) ON/OFF switch
8) Cable winder button
9) Suction power slide control
10) Rear filter grille
11) Power cable
12) Hepa-type filter
13) Filter body with ultra-fine mesh
14) Active carbon filter
15) Filter assembly
16) Air inlet PPI filter
17) Accessories holder
18) Safety device indicator light
19) Filter cleaning brush
ACCESSORIES
A) Telescopic tube
A1) Telescopic tube locking
C) Hose
D) Suction opening
E) Universal Brush
E1) Brush selector
E2) Parquet accessory (Mod.AS530)
F) Parquet brush (Mod.AS540)
H) Multipurpose nozzle
I) Lance for cleaning corners
L) Soft brush
POLTI S.p.A., in accordance with its policy of continuous improve-
ment, reserves the right to make any technical and structural modifi-
cations without prior notice.
This unit conforms to EC-directives 89/336 as amended by
93/68 (EMC) and 73/23 as amended by 93/68 (low voltage).
WW
WWAA AARR RRNN NNII IINN NNGG GGSS SS
KEEP THESE INSTRUCTIONS
• Read these instructions for use carefully before using the applian-
ce.
• Any use which does not comply with these instructions will invali-
date the warranty.
• The wiring system to which the appliance is connected must
always comply with the laws in force.
• Before connecting the appliance, make sure that the mains voltage
is the same as the voltage indicated on the data label of the applian-
ce and that the power outlet is connected to earth.
• Always turn off the appliance at the on/off switch before unplugging
it.
• If the appliance is left unused, always disconnect it from the mains.
Never leave the appliance unattended with the cable plugged into
the mains.
• Always make sure the appliance is unplugged before performing
maintenance work of any kind
• Do not pull the power cable out of the socket, but grasp the plug
itself to avoid damage to the socket.
• Do not allow the power cable to be twisted, crushed, stretched, or
come into contact with sharp or hot surfaces.
• Do not use the appliance if the power cable or other important parts
are damaged.
• Do not use electric extension leads that are not authorized by the
manufacturer, as they may cause damage or fire.
• If it is necessary to replace the power supply cable, please refer to
the nearest Polti authorised service centre, since the use of a spe-
cial tool is necessary.
• Never touch the appliance with wet hands or feet with the cable
plugged into the mains.
• Do not use the appliance when barefoot.
• Do not use the appliance near a bathtub, shower or container full
of water
• Never immerse the appliance, the cable or the plugs in water or
another liquid.
• Use of the appliance in places where there is a danger of explo-
sions is prohibited.
• Do not use the product with toxic substances.
• Do not lay the hot appliance on surfaces sensitive to heat.
• Do not leave the appliance exposed to wind or rain.
• Do not place the appliance near a live element, an electric stove or
any other source of heat.
• Do not expose the appliance to extreme temperatures
• Never let children or people who are not familiar with how the
appliance works use it.
• Do not press the buttons hard or with a pointed object such as a
pen.
• Always rest the appliance on a stable surface.
• In case of accidental fall of the appliance it is necessary to have it
checked by an authorized Service Centre as the internal safety
features may have been affected.
• In case of breakdown or malfunction switch off the appliance and
never attempt to disassemble it, but refer to an authorized Service
Centre.
• In order to avoid prejudicing the safety of the appliance, use only
original spare parts and accessories approved by the manufactu-
rer.
• Do not wind the power cable around the appliance, especially
when the appliance is still hot.
• Do not suck up liquids
• Do not use the appliance to suck up acids or solvents, as these
might cause serious damage to the appliance and above all do not
suck up explosive dust or liquids, as these could cause explosions
on coming into contact with the inside components of the applian-
ce.
• Do not suck up toxic substances.
• Do not suck up burning or incandescent objects such as embers,
ash or other material in which combustion is taking place.
CC
CCOO OORR RRRR RREE EECC CCTT TT UU UUSS SSEE EE OO OOFF FF TT TTHH HHEE EE PP PPRR RROO OODD DDUU UUCC CCTT TT
This appliance is intended for home use for sucking solids as descri-
bed and in accordance with the instructions provided in this manual.
Please read these instructions carefully and keep them, as you may
find them useful in future.
Polti declines liability for any damage or accident derived from
any use of this appliance which does not comply with the
instructions contained in this booklet.
AA
AATT TTTT TTEE EENN NNTT TTII IIOO OONN NN
Directive 2002/96/EC (Waste Electrical and Electronic Equipment -
WEEE): information for users
This product complies with EU Directive 2002/96/EC.
The crossed-out wastebasket symbol on the appliance me-
ans that at the end of its useful lifespan, the product must
be disposed of separately from ordinary household wastes.
The user is responsible for delivering the appliance to an
appropriate collection facility at the end of its useful lifespan.
Appropriate separate collection to permit recycling, treatment and
environmentally compatible disposal helps prevent negative impact
on the environment and human health and promotes recycling of the
materials making up the product. For more information on available
collection facilities, contact your local waste collection service or the
shop where you bought this appliance.
FF
FFUU UUNN NNCC CCTT TTII IIOO OONN NNII IINN NNGG GG
• Insert the hose suction opening (D) into the hose connector (5)
(fig.1).
• Unroll the power cable (11) by pulling it till reaching the yellow sign
on the cable itself. DO NOT under any circumstances unroll
beyond the red sign.
• Connect the plug to the mains.
• Press the ON/OFF switch (7). The appliance will start operating.
The ON/OFF switch (7) can also be operated by touching it with
your foot, so you do not have to bend.
• It is possible to regulate the suction power through the slide control
(9). Moving it to the right, the suction power increases, while
moving to the left, the suction power decreases. We recommend
minimum power for curtains, medium/low power for sofas,
armchairs and cushions, medium/high for carpets and high for flo-
ors and hard surfaces (ceramics, marble, etc.).
• To end suctioning, press again the ON/OFF switch (7).
EE
EEMM MMPP PPTT TTYY YYII IINN NNGG GG AA AANN NNDD DD CC CCLL LLEE EEAA AANN NNII IINN NNGG GG TT TTHH HHEE EE DD DDUU UUSS SSTT TT CC CCOO OOLL LLLL LLEE EECC CCTT TTII IIOO OONN NN
CC
CCOO OONN NNTT TTAA AAII IINN NNEE EERR RR
• Switch off the cleaner by pressing the ON/OFF switch (7). Unplug
the power cable (11) from the mains electricity supply.
• Remove the hose from the appliance, by pressing the release but-
ton on the opening (D) while pulling it outwards.
• Press the top lid opening button (4) and lift the lid (3) (fig.2).
• Lift out the dust collection container (1) using the handle (2) (fig.2).
• Press the buttons (2a) at the base of the handle (2) so that the con-
tainer opens and the dust collected inside it drops out (Fig.3).
•WARNING: since pressing the button (2a) will cause the bottom of
EE
EENN NNGG GGLL LLII IISS SSHH HH

the container to open, we recommend doing this job over a waste
bin.
• Take out the filter unit (15) and remove any residual of dirt (fig.4).
• Turn the ultra-fine mesh filter (13) anticlockwise and remove it from
the unit (fig.5)
• Remove the HEPA filter (12) from the ultra-fine mesh filter (13).
• Clean filters (12) and (13) using the brush (19) supplied.
• We recommend that you clean the filters every time you finish
using the cleaner.
•WARNING: do not use the cleaner unless the dust collection con-
tainer (1) complete with the filter is fitted.
• Place the dust collection container back in the cleaner by following
the above instructions in reverse order.
UU
UUSS SSII IINN NNGG GG TT TTHH HHEE EE AA AACC CCCC CCEE EESS SSSS SSOO OORR RRII IIEE EESS SS
Accessories can be attached directly to the flexible hose or to the
telescopic tube (A).
Using the telescopic tube (A)
The tube is about 60 cm long when closed, about 1 m when exten-
ded to its greatest length. To increase or decrease length, press the
locking (A1) and extend or reduce length as desired.
Using the universal brush (E)
Connect the brush to the telescopic tube. If you move the selector on
the brush (E1) and press with a foot, you can change the bristles
position without bending down. The position with bristles extended is
recommended for all non-carpeted floors. The position without bri-
stles is recommended for carpets.
Using the parquet accessory (E2) (model AS530)
A special parquet accessory (E2) can be attached to the universal
brush. Insert the brush (E) (with the bristles raised) inside the acces-
sory to connect it (fig.6).
Parquet brush (F) (mod.AS540)
The parquet brush is designed to clean delicate surfaces and there-
fore has bristles and wheels in material specially selected to avoid
damaging such surfaces.
Multipurpose nozzle (H)
The multipurpose nozzle is recommended for cleaning upholstery
surfaces such as the joints of sofas, armchairs, mattresses, car
upholstery, etc.
Lance for cleaning corners (I)
The lance (I) is recommended for thorough vacuum cleaning of hard-
to-reach spots such as skirting boards and folds in sofas, armchairs,
upholstered furniture and car upholstery.
Soft brush (L)
The soft brush has soft bristles for dusting delicate surfaces such as
picture frames, books, etc.
AA
AAUU UUTT TTOO OOMM MMAA AATT TTII IICC CC CC CCAA AABB BBLL LLEE EE WW WWII IINN NNDD DDEE EERR RR
Before putting your vacuum cleaner away, rewind the power cable by
pressing the button (8), being careful to accompany the cable during
winding.
GG
GGEE EENN NNEE EERR RRAA AALL LLMM MMAA AAII IINN NNTT TTEE EENN NNAA AACC CCEE EE
Always make sure the appliance is unplugged before performing
maintenance work of any kind.
FF
FFII IILL LLTT TTEE EERR RRII IINN NNGG GG SS SSYY YYSS SSTT TTEE EEMM MM
This cleaner has a 5-stage filtering system.
The first stage is the dust collection container where a cyclone effect
traps the dirt at the bottom.
The second stage is the ultra-fine mesh filter which has a HEPA type
filter (third filtering stage) inside it. The fourth and fifth filtering stages
are respectively the PPI filter and the active carbon filter.
Replacement and cleaning of the HEPA-type filter (12) and of the
ultra-fine mesh filter (13)
We recommend cleaning these filters after each use, with the brush
supplied (19). If they are particularly dirty, however, they can be
washed as follows:
• Remove the HEPA-type filter (12) and the ultra-fine mesh filter (13)
as instructed in the paragraph on “emptying and cleaning the dust
collection container”.
• Rinse both filters with running water and leave them to dry.
• Put the filters back together by following the instructions for their
removal in reverse order.
ATTENTION: make the arrow on the filter assembly (15) coincide
with the arrow on the dust collection container (1) (Fig.7).
If the filters are torn they must be replaced only with Polti original
spare parts.
Replacement and cleaning of the air inlet PPI filter (16)
• Press the container lid opening button (4) and lift the lid (3) (fig.2).
• Remove the air inlet PPI filter (16) from its holder.
• Rinse it with running water and leave it to dry.
If the filter is irreparably damaged, replace it with aPolti original
spare part.
WARNING:
• Allow the filters to dry naturally, away from light and heat sources.
It is advisable to wait 24 hours before putting the filters back in the
cleaner.
• Do not use detergent, do not scrub the filters and do not wash them
in a dishwasher.
Replacement of the active carbon filter (14)
If the filter is torn, replace it with a Polti original spare part.
• Open the rear HEPA filter grille (10) by pressing the levers on the
grille itself .
• Remove the filter and put in a new one by following the instructions
given above in reverse order.
N.B.: the active carbon filter MUST NOT be washed.
II
IIFF FF TT TTHH HHEE EE SS SSAA AAFF FFEE EETT TTYY YYDD DDEE EEVV VVII IICC CCEE EE II IISS SS TT TTRR RRII IIGG GGGG GGEE EERR RREE EEDD DD
The safety device may be triggered while you are using the cleaner
if excessive quantities of dust and dirt are picked up and the filters
(12) and (13) inside the container get clogged with dirt. This could
cause your cleaner to overheat and thus damage it. To solve this
potential problem, the cleaner has been fitted with a safety device.
This is triggered when the filters are clogged with excessive dirt. The
cleaner will therefore automatically switch off and the safety device
indicator light (18) will begin flashing. Proceed as follows to restart
the cleaner:
• Switch off the cleaner using the ON/OFF button (7) and unplug the
power cable from the mains electricity supply.
• Clean the container and the filters as described in the paragraph
on “EMPTYING AND CLEANING THE DUST COLLECTION CON-
TAINER”.
• The cleaner can now be used normally once again.
EE
EELL LLEE EECC CCTT TTRR RRII IICC CCAA AALL LLSS SSAA AAFF FFEE EETT TTYY YY
No earth required.
Ensure the mains voltage suits your appliance.
Fitting the mains plug important
The wires in the mains lead are coloured in
accordance with the following code:
• Blue: Neutral
• Brown: Live
The wire which is coloured BLUE must be connected to the Terminal
which is marked with the letter “N” or coloured BLACK.
The wire which is coloured BROWN must be connected to the
Terminal which is marked with the letter “L” or coloured RED.
It is important that the outer sheath is clamped correctly into the 3-pin
plug.
If in doubt consult your local Service Dealer or qualified electrician
before the machine is used.
A 13 AMP FUSE MUST BE FITTED TO THE MAINSPLUG.