Polygroup TGF0M3P07L02 User manual

ASSEMBLY INSTRUCTIONS MADE IN CHINA
ASSEMBLY INSTRUCTION SHEET
PARTS LIST
Key Description Qty.
1
4
4
4
1
8
8
8
6
1
1
1
1
1
1
1
1
1
Bottom Cross Frame
Horizontal Extension
(with Caster)
Vertical Connection Tube
Elbow Tube
Top Cross Flame
M5 x 15 mm Screw
M8 x 50 mm Screw
M8 x 15 mm Screw
Eyebolt
Tree section #1
Tree section #2
Tree section #3
Tree section #4
Tree section #5
Tree section #6
Tree section #7
Tree section #8
Tree top
1
2
3
4
5
6
7
8
9
10
17
18
16
15
14
13
12
11
Congratulations onpurchasing your new tree from Polygroup®! Carefully follow the
instructions below on how to quickly and easily set up your new tree.
SET UP INSTRUCTION
(1) Locate all parts as listed in the above chart.
(2) Select a suitable location to the place your Christmas tree. It should be:
• Flat and level;
• Away from any direct heat source or naked fire, such as, fireplace, heater vent, kitchen
range;
• Accessible to a power outlet.
(3) Insert Horizontal Extension 2to Bottom Cross Frame 1.
(4) Fasten 2with screw (M8 x 15 mm Screw) 8.
(5) Repeat step (3) and (4) three time to assemble all Horizontal Connection Frames 2.
(6) Insert the tree trunk Eyebolts 9to Bottom Cross Frame 1.
(7) Assemble 4 pieces of Vertical Connection Tubes 3to the ends of the Horizontal
Extensions 2. Fasten with M8 x 50 mm Screws 7.
(8) Begin to insert the tree sections to the base frame. Start by inserting the Tree section #1
10 to the center tube of the Bottom Cross Frame 1 and tighten the Eyebolts 9.
1
MODEL #: TGF0M3P07L02

ASSEMBLY INSTRUCTIONS MADE IN CHINA
9
11
10
12
13
15
14
16
17
18
(9) Continue to insert Tree Sections #2 11 , #3 12 and #4 13 to the lower section.
Connect the light sets connectors as shown in the “Tree Lights Connection Diagram”
when each tree section is added.
(10) Assemble Top Cross Frame 5to the top of the tree section #4 13 .
(11) Assemble 4 pieces of Elbow Tubes 4. Fasten with M8 x 50 mm Screws 7at the Top
Cross Frame 5. Fasten with M5 x15mm Screw 6at the connection with the Vertical
Connection Tubes 3.
(12) Insert the Eyebolts 9to the Top Cross Frame 5.
(13) Insert tree section #5 14 to the Top Cross Frame 5and tighten the Eyebolts 9.
(14) Continue to insert Tree Sections #5 14 , #6 15 , #7 16 , #8 17 and the tree top 18 .
(15) Connect the lights connectors between each tree sections as shown in the “Tree
Lights Connection Diagram”.
2

ASSEMBLY INSTRUCTIONS MADE IN CHINA
STORAGE INSTRUCTIONS
1. Remove all ornaments and decorations. For pre-lit trees, first unplug extension cord
from the wall outlet and then disconnect light extension cord between each section
of the tree.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift
straight up to remove from section below and fold all branches toward the pole.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at
the joint and rotate the upper pole in both directions. Lift up the upper pole again.
4. Continue by gently lifting straight up each section(s) from the section below and fold all
branches toward the pole until the bottom section is removed from the tree stand.
9
8
7
6
5
4
3
2
1
Insert Red Label
Plugs Into Red
Labeled Box
Insert Yellow Label
Plugs Into Yellow
Labeled Box
Insert Blue Label
Plugs Into Blue
Labeled Box
Insert purple Label
Plugs Into purple
Labeled Box
Insert Orange Label
Plugs Into Orange
Labeled Box
Insert Gold Label
Plugs Into Gold
Labeled Box
Insert Pink Label
Plugs Into Pink
Labeled Box
Insert Silver Label
Plugs Into Silver
Labeled Box
Adaptor
To Be Plugged
Into Wall
Outlet
Adaptor
To Be Plugged
Into Wall
Outlet
Insert Green Label
Plug Into Wall Outlet
Insert Green Label
Plug Into Wall Outlet
*Electrical Rating For The Tree
(For Indoor Use Only)
Input:120VAC, 60Hz, 0.38A
Output: 29V DC 0.9A
Tree Lights Connection Diagram
3

ASSEMBLY INSTRUCTIONS MADE IN CHINA
5. Carefully place all tree sections into shipping box and tape it shut.
6. When not in use, please store your tree in a cool, dry place away from sunlight.
Exposing your tree to excessive heat or humidity may damage your tree.
TROUBLE SHOOTING TIPS
SPARE PARTS
For Pre-lit Trees, If The Tree Does Not Illuminate
1. Please check to make sure that all plugs are properly connected according to the
color labels indicated in
Fig.B and the adaptor is firmly plug to the wall outlet. Refer
to assembly guide for instructions. (If the tree comes with a foot pedal, try stepping on
the on/off button).
2. Check for loose connection between light string plugs and extension cords.
3. Please check for loose, broken or missing light bulbs and replace as needed.
Loose Hinge Pin
1. Extra hinge pins are included for repairing the hinges. Place the branch into the slot
of the bracket.
2. Insert a new hinge pin through the hole and secure using the retainer washer.
(See Fig. A)
Each tree includes hinge pins/washers, and for
pre-lit trees spare bulbs are also included. If
extra parts are needed, please contact our
customer service center.
Fig.A
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroup.com. One of our customer service
representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX. TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
4