Polygroup TG90M2S85C06 User manual

ASSEMBLY INSTRUCTIONS MADE IN CHINA
TREE ASSEMBLY INSTRUCTIONS
Congratulations on purchasing your new tree from Polygroup®! This tree comes with
Fast ShapeTM technology which takes less than 10 minutes to set up and light up!
Carefully follow the instructions below on how to assemble your new tree quickly and at ease:
1. Choose an appropriate location near a wall outlet.
2. Assemble the tree stand (Fig. A) and place on a level surface.
*Electrical Rating For The Tree
(For Indoor Use Only)
2.72A 120V 60Hz
Fig. B – Tree and Light Assembly
Tree Top
Section 2
Section 3
Section 1
MODEL #: TG90M2S85C06 2019 TREE LETTER "Y"
Sku # 5168026
Fig. A - Tree Stand Assembly
Click
Pull apart tree stand legs until they
snap and form an ‘X’ shape.
To close the stand, press the metal
button and fold the legs together.
Insert Green
Label Plug Into
Wall Outlet
Insert Red Label
Plugs Into Red Label
Extension Cord
Insert Yellow Label
Plugs Into Yellow Label
Extension Cord
3. Each tree section is numbered with a sticker. Please identify all sections before assembling.
4. Assemble the tree from the bottom to the top. Insert the pole of Section 1 into the assembled
stand. Insert the pole of Section 2 into Section 1. Insert the pole of the Section 3 into Section 2.
Insert the pole of the tree top into Section 3. Ensure that all poles are firmly secure. Be sure that all
wires are free of branch hinges.
5. Connect plugs to extension cords of the same color, and then insert green label plug into the wall
outlet (Fig. B).Your entire tree should now be lit.
6.This tree is constructed with Fast ShapeTM technology. Shaping is not necessary; you just need to
slightly upsweep all tips and shift branches to fill in any gaps for a fuller, uniform look. Your
Christmas tree is now ready to be decorated.

ASSEMBLY INSTRUCTIONS MADE IN CHINA
Distributed by: Hobby Lobby Stores, Inc. • Oklahoma City, OK 73179 • www.hobbylobby.com
TROUBLESHOOTING TIPS
If The Tree Does Not Illuminate / Some Bulbs Do Not Light or Flicker
1. Check to make sure that all plugs and poles are properly and firmly connected as indicated in
Fig. B and assembly instructions.
2. Disconnect from power source, then check for loose, broken or missing light bulbs and replace as
needed.
3. Disconnect from power source, then check for blown fuses and replace as needed.
NOTE: Please make sure to use appropriate spare fuses as indicated on the label plug.
Loose Hinge Pin
1. Place the branch into the slot of bracket.
2. Insert a new hinge pin (included) through the hole,
and secure using the retainer washer (Fig. C).
STORAGE INSTRUCTIONS
1. Unplug from the wall outlet first, and disconnect other plugs.Then remove all ornaments and
decorations.
2. Disassemble the tree from the top to the bottom. Gently lift the pole straight up to remove from the
section below, and fold all branches toward the pole.
NOTE: In case of difficulty separating the poles, apply a small amount of lubricant at the joint, rotate
the upper pole in both directions, and lift the upper pole again.
3. Carefully place all tree sections into the shipping box and tape it shut.
4. Store your tree in a cool, dry place away from sunlight. Exposure to excessive heat or humidity may
damage your tree.
5. Keep out of reach of pets and children.
SPARE PARTS
This tree includes hinge pins/washers, and spare bulbs and fuses. If extra parts are needed, please
contact our customer service center.
(Fig. C)
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance or missing parts, Do Not Return To Place Of Purchase.
Please contact us at 1-888-919-0070 or visit our website at www.polygroupstore.com.One of
our customer service representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address (NO P.O. Boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem: