PolyJohn SaniStand SAN2-1000 E User manual

SAN2-1000 Assembly - May 2020
Page 1 of 4
SAN2-1000 E SaniStand®
Hand Sanitizer Stand
Assembly Instructions
We recommend reading through the entire booklet prior to proceeding with use, service or maintenance.
Height 52 in 132 cm
Width 29.5 in 75 cm
Depth 29.5 in 75 cm
Weight Empty 17 lb 7.71 kg
SPECIFICATIONS
Dimension Imperial Metric
NOTE: All dimensions are subject to change due to environmental factors.
POLYJOHN
USA
PolyJohn Enterprises Corp
2500 Gaspar Ave.
Whiting, IN 46394
Phone: [phone]
Fax: [phone]
www.polyjohn.com
[email protected]
POLYJOHN
WORLDWIDE
PolyJohn (UK) Ltd.
Equinox 1 Audby Lane
Wetherby, England LS22 7RD
Phone: [phone]
Fax: [phone]
www.polyjohn.co.uk
[email protected].uk
POLYJOHN
CANADA
PolyJohn Canada
P.O. Box 2300
199 Forest Plain Rd.
Orillia, Ontario LV3 6S2
Phone: [phone]
Fax: [phone]
www.polyjohncanada.ca
[email protected]
The E-Sanistand stores flat, can be easily assembled/disassembled,
and is a great answer to an immediate need for hand sanitation. The
mounting face of the stand can accommodate dispensers up to 6.70
in. (17 cm) wide. The unit can be assembled with the smooth finish out
or a textured finish out. Dispensers not included.
AVAILABLE DISPENSER OPTIONS
Foam Hand Sanitizer
PolyJohn Part # FD1-1000
Liquid Soap/Hand
Sanitizer Dispenser
PolyJohn Part # PSD1-1000

SAN2-1000 Assembly - May 2020
Page 2 of 4
Step 1: Insert the tabs of one panel into the slots of a second panel and slide down
into place. Repeat this step for the remaining panels.
Assembly Instructions
Wood Block
Step 2: For the final panel, You will need to twist the whole assembly to
get the last tabs into the slots. To do this, place your foot or a piece of a 2
x 4 wood block under the panel with the tabs and push down on the panel
with the slots. Place the bottom tab partially into the bottom slot but do
not fully install it. This will hold the two panels into alignment and enable
you to insert the remaining tabs into their corresponding slots. Once you
have all the tabs inserted, you can ‘pop’ the tabs through the slots and the
unit will fully engage.

SAN2-1000 Assembly - May 2020
Page 3 of 4
Assembly Instructions Cont.
Step 3: Slide the leg brace into the slots located at the bottom of the panels and insert
the tabs into the corresponding slots. Pull the tab into the slots. Repeat this for the other
leg brace. You will have to guide the second brace under the first brace and into the
slot of the side panel.
Step 5: Stand the unit upright. If you want to add a ballast of some sort (sandbag, gallon jug(s) of water/sand), do that now by
sliding the ballast down into the center of the Sani Stand.
Step 6:Install your dispensers following the manufacturer’s recommended installation instructions.
Step 7: Insert the tab on the top panel into one of the slots at the top of one of the
sides. Using a screwdriver or other tool to pry with, pry the opposite side out so that
the tab will insert into the corresponding slot.
Assembly is complete
Step 4: Turn the unit upside down and line up the pre-drilled
holes in the two leg braces. Fasten into place using the supplied
PC-000369 plastic fastener

SAN2-1000 Assembly - May 2020
Page 4 of 4
SAN2-0001
Side Panel
SAN2-0003
Top Panel
SAN2-0002
Leg Brace
PC-000369
Tree Fastener
http://www.polyjohn.com/san2-0003
http://www.polyjohn.com/san2-0001
http://www.polyjohn.com/san2-0002
http://www.polyjohn.com/pc-000369
OUR MISSION STATEMENT
“PolyJohn is a family owned, state of the art, plastics manufacturing company dedicated to providing its employees with a work
environment committed to excellence, and its customers with innovative products, services and technology that meet or exceed
their requirements.”
THANK YOU FOR PURCHASING POLYJOHN PRODUCTS!
For a video demonstration of assembly and more product information, visit
www.polyjohn.com/emergency-sanistand
For more products and information, visit
www.PolyJohn.com
2500 Gaspar Ave., Whiting, IN 46394