Poolspa VICTORIA SPA User manual

SPA Bath
VICTORIA SPA ø178
Installation and user manual

2
Dear customers,
Thank you for trusting us and buying our product!
The POOL-SPA company, one of the leaders in the European hydromassage bath market, has been
offering its world class quality products for many years. The endurance, reliability and safety of our
baths has always been of greatest importance to us; that is why we always use materials and devi-
ces from reputable suppliers.
The manual will help yoy learn about the bath installation and its use. In this way, you will be able
to use the bath without any problems for many years to come. Have a great time and enjoy our
baths!

3
CONTENTS
Introduction ............................................................................................................................. 4
PART 1 - INSTRUCTION MANUAL
1.1. Technical specification ...................................................................................................... 6
1.2. Conservation substances.................................................................................................. 7
1.3. Jets ................................................................................................................................... 7
1.4. Ventilation ......................................................................................................................... 8
1.5. Main functions accesible from the electronic control panel............................................... 8
1.6. Massage ......................................................................................................................... 12
1.7. Water ozonizing .............................................................................................................. 13
1.8. Lighting ........................................................................................................................... 13
1.9. Disinfection .................................................................................................................... 15
1.10. Thermal cover (additional optional)............................................................................... 15
1.11. Measurement and treatment formula set ...................................................................... 15
PART 2 - INSTALLATION MANUAL
2.1. Transport......................................................................................................................... 17
2.2. Site preparation............................................................................................................... 17
2.3. Bath positioning .............................................................................................................. 17
2.4. Assembly/disassembly of the wooden housing (additional option) ................................. 18
2.5. Preparation of water and electrical connections ............................................................. 18
2.6. Grounding cable connection ........................................................................................... 19
2.7. Main connection.............................................................................................................. 19
2.8. Maintenance of acrylic elements..................................................................................... 20
2.9. Electrical scheme of the Victoria SPA ............................................................................. 21
WARRANTY FOR SPA .......................................................................................................... 23
TECHNICAL PRODUCT SHEET ........................................................................................... 27

4
Introduction
In order to be able to fully use all functions of a SPA Victoria, please read all sections of this manual.
You should remember that despite the therapeutic and relaxing function of a hydromassage treat-
ment, seriously ill persons or persons suffering from heart disorder diseases or high blood pressure
need to consider special conditions created inside the SPA baths and consult their physician before
using such baths.
We recommend using hydromassage treatments in water of the average temperature of 37 degrees
for approximately 20 minutes.
It is recommended that children using the equipment are always accompanied by an adult.
This manual should be maintained for future reference.

5
PART 1 – INSTRUCTION MANUAL
Congratulations on buying a portable Victoria SPA!
SPA Victoria allows you to appreciate the ad-
vantages of hydromassage for four people
sitting places) both outside a building and in-
side a large bathroom.
The bath is equipped with an ozonator which
makes it easier to keep the water clean and is
very effective in beauty treatment. The qualities
of ozone are described in detail in Part 1.8.
Thanks to the „antifrost system”, it is even po-
ssible to take a bath when the outside tempe-
rature below freezing point. The detailed des-
cription of the system is provided in Part 1.1.
The SPA Victoria comprises:
- electronic control panel with a display
- 2 hydromassage aeration regulators
- 2 kW electric heater, with water temperature control function (6 kW as option with supply 3~400 V)
- 2,0 HP (1.5 kW) hydromassage pump
- 1.2 W axial blower
- water ozonator
- “anti-frost” system – for outside temperatures below freezing point
- water temperature sensor
- hydromassage:
• fixed mini jets - 16 pcs
• fixed ozone mini jet - 1 pcs
• 4” adjustable rotating stream jets - 4 pcs
• 4” pulsating stream jets - 2 pcs
• 4” multi-massage jets - 2 pcs
• air channels ( 95 openings)
- water suction point
- underwater halogen lighting
- filtration system with replaceable inserts
- water treatment unit
- timber steps (mahogany or pine wood - additional option).
- wooden housing (mahogany or pine wood, as an additional option)
- thermal cover (optional)
Switching off the electrical supply by using test button of the differential-current
switch after the bath is emptied is recommended, in order to avoid operation of
the hydro-massage pump without water in the bath.

6
1.1. Technical specifications
1765
1580
660
600
260
440
355
550
805
860 ± 10
930 ± 10
SPA Victoria dimensions:
- width: 1765 mm,
- depth: 765 mm,
- height: 870 mm +/- 20 mm.
Capacity: 800 l.
Weight:
~ 275 kg (without water).
Material and construction:
Sanitary acrylic strengthened by laminated
polyester, insulated with polyurethane foam,
on an aluminium frame.
Supply voltage:
230V~, 5 kW
3 ~ 400 V as option
Nominal power:
- 2 kW electric heater (6 kW as option)
- 2,0 HP (1,5 kW) hydromassage pump,
- 1.2 kW axial blower.
Power cable: 3 x 2,5 mm².
Fig. 1-1. Dimensions of SPA VICTORIA
Maximum number of people in the bath: 4.
Water:
The water should come from the water system and be properly purified and disinfected. Well water
is inadvisable, unless it has special certificates in compliance with current norms.
ANTIFROST System / Smart Winter Mode
Most important task of SPA electronic system is holding temperature of water within the range bet-
ween 15 to 400C. However electronic system has additional feature - winter operation mode (Anti-
frost/Smart Winter mode) which protects piping against frozing.
PCB integrated temperature sensor continously controls air temperature which surronds electronic
system. If air temperature decrease below 150C electronic system starts winter mode. In this mode
system switches on every pump for 1 minute (one by one). Frequency of pumps operations is con-
nected with surrounding temperature and is presented in the table below. Water heater works inde-
pendently of air temperature sensor, it depend only of water temperature sensor.
Temperatura 0 C Operating frequency (min)
12 < t ≤15 120
9 < t ≤12 60
6 < t ≤930
t ≤615
• Operation mode ANTIFROST system is marked by ICE symbol on the LCD screen.
• Stand by mode doesn’t affect on ANTIFROST system operations.
• After activating the ANTIFROST system all functions beside water heating are not used.

7
• All these functions are not available until ICE symbol disappered. Is possible to take a bath but use
of any pump.
• If electronic system detects temperature below 150C degrees of the surrounding air then ANTI-
FROST systems starts after 15 minutes from last pump switch off.
• If during filtration mode ANTIFROST system starts, filtration mode will be switch off.
1.2. Conservation substances
The acrylic surface of the bath is covered with a thin layer of wax, being the remaining of the polis-
hing process. Metallic elements have been coated with silicone oil for protection purposes. The SPA
should be washed off (e.g. with a dishwashing detergent) prior to filling the bath with water.
1.3. Jets
SPA VICTORIA is equipped with an innovative jet system:
Jets Quantity Photo
fixed mini jets 16 pcs.
fixed ozone mini jet 1 pcs.
4” adjustable rotating stream jets 4 pcs.
4” pulsating stream jets 2 pcs.
4” multi-massage jets 2 pcs.
Location of individual water jets is shown in detail on fig. 1-4.
The hydromassage can be intensified by turning the jets in a
clockwise direction of about 90°. Turning in an anti-clockwise
direction will close the jets.
Fig. 1-2. Increasing massage intensity

8
1.4. Ventilation
High water temperature during bathing in the bath (up to 40°C) causes emitting of big amounts of
steam. An efficient ventilation system should be provided in the room with the bath. Installing of a
steam condenser in the room which will maintain constant air humidity will minimize the risk of dam-
pening of walls and ceiling. An air-conditioning system in the building allows for elimination of the
steam condenser. Such problem does not exist in case of a bath operating in open air conditions.
1.5. Main functions accessible from the electronic control panel.
Victoria SPA control panel
1.5.1. Switching on/off the pump
The hydromassage pump can be switched on/off directly from the electronic control panel. After
starting the pump, this icon
1
, appears on the display and after switching it off, the icon disap-
pears.
With the two-gear pump, pressing the button for the first time switches the pump over to a low gear
(filtration; this icon
1
blinks on the display). Pressing the button once again switches the pump over
to a top gear (massage; this icon
1
appears on the display). Pressing the same button again swit-
ches the pump off and the icon disappears from the display.
In some cases, the pump automatically switches over to a low gear after connecting it to the power
supply. This happens during the filtration or the water heating process in the SPA bath.
The pump working in massage mode have automatic time out (20 minutes) from the last button
start.
- unavailable
1.5.2. Extra equipment - airmassage (on/off)
1.5.3. Switching on/off the lighting
Press the button with the lamp symbol on it to switch on the lighting. This icon appears on the
display. Press the same button again to switch off the lighting, and the icon disappears from the
display. The lighting switches off automatically after 2 hours from the last pressing of the lighting
on/off button.
Press and hold this button for more than 5 seconds to view from inside the spa the water tem-
perature and time display projection, to read these data.

9
1.5.4. Setting the right time
The controller is fitted with the RTC system (real-time clock), which works permanently even after
disconnecting the main power. The RTC system makes it easier to use the SPA, since the controller
memorize the clock, filtration and the economy mode setting even after the main power is off. It is
not necessary to set the filtration start time and its duration again.
To change the RTC system setting:
Press and hold the clock button for about 5 seconds until the clock icon starts blinking and
appears permanently on the display.
Set the hour by using the up/down arrow buttons
Press the clock button once again to set minutes by using the up/down arrow buttons
Press the clock button once again to save the current setting after the time modification. If no bu-
tton is pressed for longer than 5 seconds, the controller returns to its normal mode without saving
the setting.
1.5.5. Economy mode
After switching on the economy mode (energy saving mode), the controller keeps the temperature
10°C (50°F) lower than that previously set.
When this mode is working, this icon appears on the display. The economy mode can be activated
(the icon is displayed permanently) or suspended for 40 minutes from the moment of switching off the
last pump, when at least one pump is switched on during this mode. Regardless of the temperature
previously set, the controller maintains the water temperature not lower than 15°C (59°F).
To enter the economy mode:
Press this button
The display will then show „Edx”, where x stands for the economy mode duration (from 0 to 24 hours)
Ed0 – the economy mode is switched off,
Ed24 – the economy mode is working continuously.
To change the hour, use the up/down arrows and use this button on the control
panel to confirm the setting.
After confirming the settings, the display will show the time when the economy mode is to start.
Set the hour and minutes using the arrows and confirm the setting with this button
Confirming the minutes with this button the economy mode is set. The display returns to its
normal status.
The setting of the economy mode is remembered even after the power cut-off.
1.5.6. Filtration
In this system, the filtration process is based on water ozonation. The water is sucked by the skim-
mer filter and then mixed with ozone by the injector. After that, the water returns to the SPA bath
through the ozone jet. The filtration process consists on two steps. The first step lasts 1 minute,

10
water pump work at the highest speed, while the heater is on. When one pump works in a low gear
along with the water ozonator and the electric heater. The duration of filtration depends on the time
setting. Filtration mode is indicated by this special icon on the display. Filtration process can be
suspended (the filtration icon is blinking on the display) by switching on any of massage pumps.
Filtration will return to its normal mode after 40 minutes after user last operations. Switching the
lighting on does not suspend the filtration process.
Setting filtration parameters:
Press the filtration button
The display will show Fdxx, where xx stands for the filtration duration from 0 to 12 hours.
If xx is set on 0, the filtration does not work
Filtration duration can be changed with these arrows and the selected value is confir-
med by pressing the filtration button
The blinking filtration start time will appear on the display
Changes are made with these arrows and confirmed by using the filtration button
After confirming the selected minutes by pressing the filtration button, the controller memorizes
the setting and returns to its normal work. If no button is pressed for longer than 5 seconds during
the setting procedure, the controller will quit the filtration setting menu and will not remember any
changes.
1.5.7. Fast filtration (Boost)
The “boo” function enables to make faster water filtration. During this function, all the pumps work for
1 minute. Additionally, pump works in a fast gear for 45 minutes along with the ozonator. The heater
works normally during the fast filtration process. After switching this function on, the „boo” sign ap-
pears on the display and is present until this function is finished. Fast filtration process is triggered
by pressing and holding the pump 1 button for 10 seconds. This function can be switched off earlier
by starting any other pumps.
1.5.8. Setting the water temperature
To set the water temperature, press the arrow buttons on the control panel.
The selected temperature does not have to be confirmed, but only set. The display, after 5 seconds
from the last pressing, will return to the previous status and start showing the current water tempera-
ture. The controller maintains the set temperature with an accuracy of ± 0,5°C (1°F). If the water
temperature is lower than that previously set, the controller will start the heater and low gear pump
(filtration circuit) and keep it on until the water reaches its required temperature. If the economy mode
is on the controller keeps the water temperature lower by 10 degrees than that previously set.
After the economy mode is off, the controller returns to maintaining the previou set temperature.
1.5.9. Increasing the maximum temperature
This function allows the user to increase the water temperature by two degrees centigrade above
40°C (104°F). To set the temperature above 40°C, set the maximum temperature and next press
and hold the up arrow button for 5 seconds until the Orx.x sign appears on the display, where
x.x signifies how much the temperature value is to be increased above the maximum temperature.
This value can be increased half a degree, and the maximum value is two grades, so the maximum water

11
temperature is 42°C. To return to a normal mode of setting the water temperature, press the down arrow
button a few times until the normal temperature, ranging from 15 to 40°C, appears on the display.
1.5.10. “Stand-By” function
This function blocks access to all devices connected to the controller for 60 minutes. This function
stop all functions without need of disconnecting the power supply. To switch off this function, press
this button 5 seconds. After switching this function on, the “Sby” sign will appear together with
the time left to the end of this function.
There are three methods to end this function:
Wait 60 minutes until this function stops working.
Press this button for longer than 5 seconds when the function works.
Disconnect the controller from the power supply.
The “Stand-By” function blocks the filtration function. If 40 minutes after going out from “Stand-By”
mode SPA still will be in filtration period Filtration mode will start again.
1.5.11. Control panel keyboard locking
Partial keyboard locking:
Press and hold this button . During this operation, the key-shaped icon blinks.
The LocP sign will appear on the display after pressing this button on the control panel for 3
seconds. Once this sign has appeared, the function becomes active and the key icon is on perma-
nently. The control panel is locked.
Release the button (only jets, light, air/aux).
To unlock the panel, press and hold this button for not less than 5 seconds.
The LocP sign will appear on the display if any button is pressed after locking the keyboard. The
partial keyboard locking function is not remembered after a power cut-off.
Total keyboard locking:
Press and hold this button . The key-shaped icon blinks during this operation.
The “LocP” sign will appear on the display after pressing this button on the control panel for 3
seconds. Once this sign has appeared, the function becomes active and the key icon is on perma-
nently. The control panel is locked (all of the buttons).
Keep this button pressed.
After 5 seconds the LocF sign appears, and since that moment the function is active.
Release the button.
To unlock the panel, press and hold this button for not less than 5 seconds.
The LocF sign will appear on the display if any of the locked buttons is pressed after locking the
keyboard. The total keyboard locking function is not remembered after a power cut-off.

12
1.6. Hydromassage
There are water and air massage systems installed in the bath.
1.6.1. Hydromassage (whirl bath)
Hydromassage is the pressure on defined muscles exerting by stream of water or stream of air
and water. Water or air and water at high pressure bring out from regulated jets and hit on body
surface. It tones and relaxes the skin, at the same time massaging and cleaning it. Hydromassage
is recommended for anybody with spine, arthritic or muscle pains, respiratory system diseases or
gynaecological problems.
Water massage system (hydro-massage) is made of the following elements:
- a set of 25 water and air jets, supplying water or a water and air mix of sufficient speed to the water
section of the bath;
- a hydromassage whirl pump, enforcing water circulation;
- 2 regulators of air supply to the hydro-massage jets, installed at the edge of the bath; used for
regulation of massage intensity;
- water suction point.
The water massage intensity regulation is possible by means of aeration regulators located at the
perimeter of the bath top, by adding air to the water stream coming from the jets. The more air, the
stronger the stream is. An accurate water massage power regulation can be also made by the jets,
which is described in detail in part 1.3.
Hydromassage intensity is increased by turning the regulator knobs clockwi-
se (towards the “ON” sign)
Hydromassage intensity is decreased by turning the regulator knobs anti-clo-
ckwise (towards the “OFF” sign)
Fig. 1-3.Massage intensity
regulator
Each of the regulators is responsible for controlling a different jet section; a detailed breakdown is
shown on fig. 1-4.
A
-fixed mini jets
B
-fixed ozone mini jet
C
-4" adjustable rotating stream jets
F
- underground lighting
G
- water suction
H
- control panel
I
- aeration regulators
D
-4" pulsating stream jets
E
-4" multi-massage jets
B
F
G
H
I
I
A
A
D
C
C
A
A
C
E
E
DA
A
AA
A
A
CA
A
A
A
AA
G
Fig. 1-4. Location of water jets and aeration control

13
1.6.2. Airmassage (pearl bath)
In airmassage, heated air is pumped into water by a blower. Millions of bubbles come from the
perforated bath bottom, actively massaging the body. The bubbles stimulate the circulatory system,
relax muscles and joints. Their activity may be compared to a normal hand massage. It soothes the
nervous and respiratory system, and improves metabolism.
The airmassage system is made of the following elements:
- properly situated air channels, forming an integral part of the bath, topped with a number of
openings within the water section of the bath,
- a blower with a suction noise silencer,
- a loop protecting against water intrusion into the blower.
1.7. Water ozonizing
Oxygen (O )
2Ozone (O ) 3
O1O3
O2
Oxygen atoms
Electric
current
or UV light
The ozonized air has, apart from a nice scent, many
therapeutic and antiseptic properties. It greatly helps in
keeping the water clean both in the bath and the plant.
Ozone definitely supports maintenance hygiene in the
SPA. The heated and ozonized air is pumped into the air
duct system underneath the bath. Operating only during
filtration.
Fig. 1-5. Ozone producing process
Caution : ozoning does not occur during hydromassage!
Ozone is healthy:
- it is more and more popular in beauty treatment,
- helps to remove stretch marks, cellulite and wrinkles,
- improves complexion,
- helps to treat varicose veins and skin diseases,
- helps in heart and circulatory system problems,
- soothes problems connected with menopause.
Why is ozone necessary in SPA?
- it has antiseptic properties,
- helps to keep the bath clean,
- helps to keep water clean, fresh and clear,
- eliminates any unpleasant water smell,
- eliminates fungi and yeast in water,
- refilling with water does not need to be frequent.
1.8. Lighting
There are attached to under water ligth two coloured overlays made
from plastic in two colours: red and blue (see pict. 1-6). Put it on light
cover in inner part of SPA. To remove overlay use screwdriver with flat
end - discuter edge of overlay to slide out of light cover.
Fig. 1-6. Coloured overlays for under-
water light

14
Underwater lighting must not be used when there is no water in the bath!!!
Underwater lighting must be switched off before water is drained from the bath !!!
SPA Victoria Filtration System:
The system is composed of the following elements:
• skimmer filter,
• water pump,
• pipe system with a suction point,
• pipe system with water jets,
• ozonizer,
• injektor.
Skimmer filter
Water pump
Suck
Ozonizer
Injektor
Ozone
jet
Ozone
Water
Water + ozone
The skimmer filter used in the SPA Victoria has the filtration area of 1.86 m2and the flow capacity of
approximately 19 m3/h.
Filter insert replacement :
1. Tilt the hatch towards the inside of the bath
2. Remove element B and subsequently element C
3. Remove element D and subsequently element E
4. clean or replace filter inserts D and E
5. install new filters in the opposite order – i.e. E and D
6. Install elements C and B
7. cleaning relies on rinsing of the insert with warm running water.
Fig. 1-8. Skimmer filter used
for SPA Victoria
It is recommended to clean filter inserts every 2 days
and replace inserts not less frequently than once a
year.
The water pump operating in the filtration mode has efficiency at
the level of approximately 10 m3/h, while operating in the hydro-
massage mode – at the level of approximately 20 m3/h. The suction
point used for SPA Victoria has the efficiency of approximately 42,7
m3/h and has a special anti-adhesive structure ensuring safety of
operation of the bath.
Fig. 1-9. Suck used for SPA Victoria
Fig. 1-7. Filtration system scheme for a SPA VictoriaFig. 1-7. Filtration system scheme for a SPA Victoria

15
1.9. Disinfection
Disinfection process in the SPA Victoria, is ozone based. Ozone is used during filtration. Additionally,
the bath is equipped with a START SET of measurement and treatment agents for pH correction and
disinfection with active oxygen (more information in part 1.11).
1.10. Thermal cover (additional option)
The SPA Victoria can be optionally provided with a thermal
cover.
We recommend to order the cover in cases when:
- the bath is going to be used outdoors, i.e. in a garden (the
cover prevents the water from excessive cooling down and
keeps the bath clean as well as preventing excessive hea-
ting of the bath perimeter by sun rays),
- when the bath is going to be used very frequently indo-
ors (the cover serves to prevent the water from excessive
evaporation).
Fig. 1-10. Thermal cover for SPA Victoria
If the bath is to be exposed to operation in direct sunlight, it is recommended to
use the thermal cover after taking a bath, to prevent damage resulting from sun-
light heat.
1.11. Measurement and treatment formula set
Before the first bath and depending on how frequently the SPA Victoria bath is
used, please check the water pH with the enclosed Dinofresh/pH Tester!!! (Mini-
mum once every 2 weeks).
pH measurement:
• rinse a test container and fill to the 10 ml mark with pool water,
• add 1 PHENOLRED (fig. 1-11) tablet to the container and close the plug,
• shake the container and dissolve the tablet,
• compare the test water colour with the colours in the column on the left and read the pH of the
water sample,
• all pH values below 6,8 make the water turn yellow,
• all pH values above 8,2 make the water turn red,
• ideal values range from 7,2 to 7,6.
Dinofresh measurement:
This is a measurement of the active oxygen concentration contents, informing about the oxygen
content level in water.
• Rinse a test container and fill to the 10 ml mark with pool water.
• Add 1 DPD no 4 tablet to the container and close the plug.
• Shake the container and dissolve the tablet.
• Compare the colour of the solution with the colours in the column on the right to read the Dinofresh
value of the water sample.
• The recommended values range from 5,0 to 8,0 mg/litre.

16
Important instructions:
• do not touch the tablets! It may distort the test outcome,
• reading of results must take place immediately after the tablet has dissolved in water,
• after each measurement the test container and its lid should be thoroughly rinsed.
Otherwise, it may also distort the results.
The tablet reagents are provided for the purpose of the above described chemi-
cal analyses and should not be used for any other purposes. The tablet reagents
must not be handled by children.
Fig. 1-11. Start set: test container and DPD and Phenolred tablets
If the measured pH is outside the range 7,2 to 7,6 it will be necessary to use SPA Victoria
granules to correct the pH value.
1. Dinominus - pH decreasing granules.
Dosage: about 10 g/1000 litres to lower pH by 0,1 (in case of Victoria: 10g).
The granules should be poured over water surface as the filtration pump is on.
The pH measurement should take place directly after the correction. Do not add the granules any-
where close to the skimmer.
2. Dinofresh - active oxygen granules for water disinfection to be added to the skimmer.
Dosage: 25g/1000 litres is a start value (25g for Victoria), and then in 5g doses or multiplied doses
to restore the 5 ÷ 8 mg/l Dinofresh level in water.
3. Dinoclean S - alkaline, liquid and strong chemical to clean the rim of the bath and dissolve fats. It
is perfect to clean any greasy stains from the walls or the rim of the bath, and to remove calciferous
deposits. Dosage: spread concentrated or dissolved (1:10) agent on dirty surfaces using a brush.
Rinse thoroughly after a short period of time. Do not let the agent dry before rinsing.
A set of disinfecting agents for SPA VICTORIA can be purchased at most showrooms where POOL-
SPA products are offered in the country.
It is a natural phenomenon that in SPA baths the pH value of water tends to
increase. However, very rarely the pH value decrease can be observed. It is then
recommended to use Dinoplus granules, which can be ordered through the sho-
wroom of the Victoria SPA manufacturer.

17
Fig. 1-12. Set of measurement and treatment agents
PART 2 – INSTALLATION MANUAL
2.1. Transport
The bath should only be transported in the original manufacturer’s packaging! After unpacking, the
bath can be carried by the aluminium frame or acrylic elements. The pipes and cables must not be
used as handles/grips!!!
2.2. Site preparation
The portable Victoria SPA may be operated both indoors and outdoors. The site for the bath
should comply with the following conditions:
a) the proper area and the proper transportation routes (in case of closed premises),
b) 230V electrical supply and ensured efficiency of the electrical connection in respect of the equip-
ment (for standard equipment the rated power consumption is 5kW and requires use of a 3x2,5 mm2
electrical cable as the connection – with regard to the safety of the users, in all cases the supply
cable must be protected by means of a differential-current switch with the standard rated switch off
current of 30 mA),
c) water supply and drainage,
d) levelled floor,
e) sufficient ventilation (indoors),
f) in case of a bath installed in closed premises, access to the electrical equipment must be provided
for maintenance or inspection purposes.
2.3. Bath positioning
1765
1580
660
600
260
440
In order to ensure proper operation conditions, the floor
should be very well levelled. All the bath legs should be on
a solid and hard surface. The total weight of the bath with
water and four people is about 1450 kg. The weight of the
bath should be equally spread over the 11 bath legs. The
surface load is 582 kg/m2.
Fig. 2-1. Location of bath points of support for
SPA Victoria

18
2.4. Assembly/disassembly of the wooden housing (additional option)
Fig. 2-2. Assembly/disassembly scheme for the wooden housing for SPA Victoria
Disassembly and assembly of the housing is based on unscrewing (using a T 15 size star spanner)
of two screws located at the ends of the timber elements (in their lower section) and moving them
aside.
2.5. Preparation of water and electrical connections
T
Due to the obligations resulting from legal regulations and due
to the fact that individual equipment elements in the SPA Vic-
toria are constantly powered, it is recommended to install an
electrical line of three wires (one phase wires, one neutral and
one grounding wire) or five wires (as option for 3~ 400 V) with a
suitable manual disconnecting mechanism, forming part of the
general electrical installation in the house.
The electrical connection line needs to be, first of all, pro-
tected with a 40A safety fuse and then connected to an au-
tomatic differential-current switch of the maximal sensitivi-
ty of 30 mA.
Fig. 2-3. A differential-current switch
with an indicated test button
Both electrical connection safety systems are prepared by the
client.
In order to prevent activation of the bath without water, the electrical supply should be disconnected
by pressing the test button of the differential current switch (see Fig. 2-3). The differential current
switch does not form part of the bath equipment.
The bath can be connected to the water and sewage systems permanently or
the bath can be filled and drained by means of flexible hoses disconnected after
each operation. The flexible hose set of the bath includes a T-pipe with a ½”
coupling for filling of the bath through the hydro-massage jets. (see Fig.2-4.)
Fig. 2-4. T-pipe with
a ½” coupling

19
The fixed piping system includes release valves lo-
cated near the skimmer-filter; at the outlets of which
fixed or removable hose connection with the sewage
system should be made (See Fig. 2-5).
Fig. 2-5. Sewage connection for SPA Victoria
2.6. Grounding cable connection
A grounding installation with a 2,5 mm2wire is necessary for the circuit
breaker and safety mechanisms to work properly. The wire should be con-
nected to the frame as shown on fig. 2-6.
Fig. 2-6. Place of connec-
tion of the earthing wire
2.7. Main electrical connection
The power cable must be connected to the fixed power supply to an IP X5 safety level. Socket in-
stallation is not permitted. The power installation in the wall can be connected by a junction box. An
IP X5 junction box should be in the 3rd zone, and at least 20 cm above the floor level.
According to current regulations, sockets may not be installed within zones 0,1 and 2.
Zone 0 is the area inside the bath.
Zone 1 is the zone 0 area plus the space up to 2.25 m above the floor.
Zone 2 is the zone 1 area extended by 0.6 m, again up to 2.25 m above the floor.
Zone 3 is the area reaching 2.4 m beyond zone 2, up to 2.25 cm above the floor.
2,4 m
2,4 m
Zone 1Zone 1
Zone 0
Zone 3
Zone 3
Zone 2
Zone 2
2,25 m
0,6 m 0,6 m
0,2m
Fig. 2-7. Location of protection zones

20
1765
1580
660
600
440
Skimerofiltr
230V(3x2,5mm)
electric connection
with 5 kW efficiency,protected
by a circuit breaker
(30 mA cut-off value)
2
Sewage connection
50 mm
Water connection 1/2”
for water filling
Fig. 2-8. Location of SPA Victoria connections
2.8. Maintenance of acrylic elements
Only mild fluids (not containing acetone, abrasive or
caustic substances) should be used to clean the bath.
The structure and low level of surface adhesion of ac-
rylic mean that keeping the bath clean should not be
a problem.
Mechanically damaged gloss acrylic (small, shallow
scratches) can be easily repaired. In the case of small
scratches, a small amount of wax-free car-polish sho-
uld be used. Deeper scratches may be removed by
sandpaper in order of grain 800, 1200, 2000 followed
by the car-polish mentioned earlier. In order for the
surface to be smooth it should be ground in a circular
motion, followed by a wax car polish (which provides a
high level of shine). Repairs can be made with a repa-
ir kit available at the dealer shops; however we re-
commend using the services of our authorized
POOL-SPA service staff. Fig. 2-9. The repair kit for SPA baths