PORSCHE DESIGN PDT60 User manual

USER MANUAL
PDT60 True Wireless Earphones

1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your True wireless
earphones 3
What's in the box 3
Other devices 3
Overview of your True wireless earphones 4
3 Get started 5
Charge the battery 5
Pair the earpieces with your Bluetooth
device for the st time 6
4 Use your headphones 7
Connect the earpieces to your
Bluetooth device 7
Control ANC (active noise
cancelation) 7
Manage your calls and music 8
LED indicator status 8
Voice Assistant 9
5 Reset the earpieces 10
6 Technical data 10
7 Notice 11
Declaration of conformity 11
Disposal of your old product
and battery 11
Remove the integrated battery 11
Compliance with EMF 12
Environmental information 12
Notice of compliance 12
8 Trademarks 14
9 Frequently asked questions 15
Contents

1 Important safety
instructions
Hearing Safety
Danger
 To avoid hearing damage, limit the time you use
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter the safe
listening time is.
Be sure to observe the following guidelines when
using your headset.
• Listen at reasonable volumes for reasonable
periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that you
can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from earphones
and headphones can cause hearing loss.
• Using headphones with both ears covered
while driving is not recommended and may
be illegal in some areas while driving.
• For your safety, avoid distractions from
music or phone calls while in trac or other
potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
 Do not expose headphones to excessive heat
 Do not drop your headphones.
 Headphones shall not be exposed to dripping , splashing
water.
 Do not allow your headphones to be submerged in
water.
 Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
 If cleaning is required use a so doth, if necessary
dampened with a minimum amount of water or diluted
mild soap, to clean the product.
 The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the like.
 Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery, can result
in an explosion;
• Leaving a battery in an extremely high temperature
surrounding environment can result in an explosion or
the leakage of ammable liquid or gas;
• A battery subjected to extremely low air pressure that
may result in an explosion or the leakage of ammable
liquid or gas.
About operating and storage temperatures and
humidity
• Store in a place where temperature is between
-20°C (-4°F) and 50°C (122 °F) (up to 90%
relative humidity.
• Operate in a place where temperature is
between 0°C (32°F) and 45°C (113 °F) (up to
90% relative humidity.
• Battery life may be shorter in high or low
temperature conditions.
• Replacement of a battery with an incorrect
type that can defeat a safeguard (for example,
in the case of some lithium battery types);

2 Your True
wireless
earphones
What's in the box
Porsche Design True wireless earphones
Porsche Design PDT60
Replaceable rubber ear caps x 3 pairs
Quick start guide
Other devices
A mobile phone or device (e.g. notebook,
tablet, Bluetooth adapters, MP3 players etc)
which supports Bluetooth and is compatible to
the headset (see 'Technical data' on page 8).
Congratulations on your purchase, and welcome
to Porsche Design! With this Porsche Design
True wireless earphones, you can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
USB-C charging cable (for charging only)
Global Warranty
Safety leaet
Quick start guide
Warranty card

Overview of your True
wireless earphones
Multi-function touch
LED indicator (earpieces)
LED indicator (charging box)
USB-C charging slot
1
1
2
3
4
2
3
4

3 Get started
Charge the battery
Charging Box
Note
 Before you use your earpieces for the rst time, place
the earpieces in the charging box and charge the
battery for 3 hours for optimum battery capacity and
lifetime.
 Use only the original USB-C charging cable to avoid any
damage.
 Finish your call before charging the earpieces, as
connecting the earpieces for charging will power the
earpieces o.
Connect one end of the USB cable into the
charging box, and another end into the power
source.
• Charging process is veried by the white
LED light on charging box.
• When the charging box is fully charged,
4 LED indicators turn on.
Tip
 The charging box serves as a portable backup battery
for charging the earpieces. When the charging box is
fully charged, it supports 3 times full recharge cycle for
the earpieces.
The charging box starts charging.
Tip
 Normally, a full charge takes 2 hours (for the earpieces
or charging box) by USB cable.
Earpieces
• LED indicator on earpieces turn on for 5s
when fully charged.
• LED indicator on earpieces turn on for 10s
when charging.
Place the earpieces in the charging box and
close the slide.
The earpieces start charging.

The LED on both earpieces ash in
white & blue alternately.
Pair the earpieces with your
Bluetooth device for the st
time
Push out the top cover from charging box.
Make sure that the headset is fully
charged and powered o.
Single earpiece (Mono mode)
Take either Right or Le earpiece out from
charging box for Mono use. The earpiece will
power on automatically. There will be a voice
“Power on” from earpiece.
Note
Note
 Aer powering on, if the earpieces cannot nd any
previously connected Bluetooth device, it will
automatically switch to pairing mode.
Note
 Take the second Earpiece from the charging box and
they will pair each other automatically.
 The earpieces stores 4 device in the memory. If you try to
pair more than 4 devices, the earliest paired device is
replaced by the new one.
Pair the earpieces with
another Bluetooth device
The earpieces are now in pairing
mode and is ready to pair with a
Bluetooth device (e.g. a mobile
phone)
Turn on the Bluetooth function of your
Bluetooth device, select Porsche
Design PDT60.
Turn on the Bluetooth function of your
Bluetooth device.
Pair the earpieces with your
Bluetooth device. Refer to the user
manual of your Bluetooth device.
The following example shows you how to
pair the earpieces with your Bluetooth
device.
If you have another Bluetooth device that you
want to pair with the earpieces, make sure the
Bluetooth function in any other previously
paired or connected devices are turned o.
Long touch over 5 seconds both Le & Right
side simultaneously with earpiece on ear,
release when Pairing voice prompt is heard.
Enter the earpieces password “0000” (4
zeros) if prompted. For those Bluetooth
devices featuring Bluetooth 3.0 or higher,
no need to enter a password.
Porsche Design PDT60

Dierent ANC mode can be toggled via double
tap on the Le earpiece.
• ANC function is auto active when put into
the ear.
• Touch the Right MFB panel twice, it will
change to Awareness mode.
• Touch the Right MFB panel twice again, it
will turn the ANC function o.
Tip
Note
 The earpieces cannot connect to more than 1 device at
the same time. If you have two paired Bluetooth devices,
only turn on the Bluetooth function of the device that you
want to connect.
 If you turn on the Bluetooth function of your Bluetooth
device aer turning on the earpieces, you have to go to
the Bluetooth menu of the device and connect the
earpieces to the device manully.
Tip
 If all ready connected to the Bluetooth device, by
removing the earpieces, it will automatically change to
sleep mode aer 3 minutes. When put earpiece back, it
will return to active mode.
 If the earpieces fails to connect to any Bluetooth device
within 3.5 minutes, it will turn o automatically to save
the battery life.
 In some Bluetooth devices, connection may not be
automatic. In this case, you have to go to the Bluetooth
menu of your device and connect the earpieces to the
Bluetooth device manually.
The blue LED ashes.
The earpieces will search the last
connected Bluetooth device and
reconnect to it automatically. If the last
connected device is not available, the
earpieces will enter pairing mode.
4 Use your
earpieces
Turn on the Bluetooth function of your
Bluetooth device.
Open the top cover from charging box.
Connect the earpieces to your
Bluetooth device
Task
ANC ON Right
earpiece
Right
earpiece
Double tap
Double tapAwareness
mode
ANC OFF Right
earpiece
Right
earpiece
Double tap
Tap and holdAttention
mode
Multifunc-
tion button
Operation
Control ANC (active noise
cancelation)
Enable ANC
ANC ON
Awareness
mode
ANC OFF

Task
Turn the
earpieces on.
Earpiece take
out from
charging box
to power on
Earpiece put
back to
charging box
to power o
Turn the
earpieces o.
Power on/o
Multifunc-
tion button
Operation
Music control
Play or pause
music
Skip forward Right
earpiece
Triple taps
Adjust volume
+/-
Via mobile
phone control
Right
earpiece
Tap once
Manage your calls and music
Task Multifunc-
tion button
Operation
Headphones status Indicator
ANC mode is toggled The blue LED will
turn on.
ANC LED indicator status Call control
Pick up/ Hang
up call
Reject call Right
earpiece
Tap and hold
Right
earpiece
Double taps
Task Multifunc-
tion button
Operation
LED indicator status
The earpieces are
connected to a
Bluetooth device.
The earpieces are
ready for pairing
The earpieces are on
but not connected to a
Bluetooth device
Low battery level
(earpieces)
Blue LED blink 2x
every 5s
The blue & white LED
ash alternately
White LED blink
every 1s
(auto turn o aer
3min)
White LED blink
every 5s
Headphones status Indicator
Battery is fully
charged
(charging box).
Refer to Case LED

Battery LED indicator on Bluetooth
device
It will show a battery indicator on Bluetooth
device aer connected to earpieces.
Task Button Operation
Le
earpiece
Trigger voice
(Siri/Google)
assistant
Tap and hold
1 second &
release
Voice Assistant
How to wear
Charging Box (4 blue LED)
Charging Box LED
(USB on)
Indicator
Continue to lit as
long as USB is on
Tip
 When USB is o, the LED is lit for 30s aer case open or closed
Charging Box LED
(USB o)
Indicator

5 Reset the
earpieces 6 Technical data
Note
 Specications are subject to change without notice.
Music time — ANC enabled: 4.5 hours |
ANC disabled with Bluetooth: 5 hours
Talk time — ANC enabled: 4.5 hours | ANC
disabled: 5 hours
Standby time — 200 hours
Charging time: 2 hours
Lithium-ion battery 50 mAh on each
earpiece, Lithium-ion battery 410 mAh on
charging box
Bluetooth version: 5.0
Compatible Bluetooth proles:
• HSP (Hands-Free Prole-HFP)
• A2DP (Advanced Audio Distribution
Prole)
• AVRCP (Audio Video Remote Control
Prole)
Supported audio codec: AAC, SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 6 dBm
Operating range: Up to 10 meters (33
feet)
Auto power o
USB-C port for charging
Low battery warning: available
On your Bluetooth device, go to the
Bluetooth menu and remove Porsche
Design PDT60 from the device list.
Turn o the Bluetooth function of your
Bluetooth device.
Tap & hold multi-function touch for >25s
on each earpiece individually.
Return earpieces to charging box & close
the lid.
Follow steps in “Use your earpieces-Con-
nect the earpieces to your Bluetooth
device.”
Pair the earpieces with your Bluetooth
device, select Porsche Design PDT60.
5
1
2
3
4
6
If you encounter any pairing or connection issue,
you can follow the following procedure to reset
your earpieces.

7 Notice
Declaration of conformity
Disposal of your old product
and battery
Your product is designed and manufactured with
high quality materials and components, which
can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains a
built-in rechargeable battery covered by
European Directive 2013/56/EU which cannot
be disposed of with normal household waste. We
strongly advise you to take your product to an
ocial collection point or a Porsche Design
service centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product and
rechargeable batteries with normal household
waste. Correct disposal of old products and
rechargeable batteries helps prevent negative
consequences for the environment and human
health.
Remove the integrated battery
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headphones.
• Make sure the earpieces is disconnected
from the charging box before removing the
battery.
• Make sure the charging box is disconnected
from the USB charging cable before
removing the battery.
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compliance with
the essential requirements and other relevant
provisions of Directive 2014/53/EU. You can nd
the Declaration of Conformity on
www.porsche-design.com.

Compliance with EMF
This product complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old equip-
ment.
Notice of compliance
The device complies with the FCC rules, Part 15.
Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio communi-
cations.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment o and on, the user is encour-
aged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between equipment
and receiver
Connect the equipment into an outlet on a
circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter.
Canada:
This device contains licence-exempt transmit-
ter(s)/ receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1)This device may not cause interference.
(2)This device must accept any interference,
including interference that may cause
undesired operation of the device.
Caution: The user is cautioned that changes or
modications not expressly approved by the
party responsible for compliance could void the
user's authority to operate the equipment.

IC Radiation Exposure Statement:
This equipment complies with Canada radiation
exposure limits set forth for uncontrolled
environments.
This transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter.
Avis de conformité
Cet appareil satisfait aux règlements de la FCC
partie 15 du Code of Federal Regulations. Son
fonctionnement est assujetti aux deux conditions
suivantes :
1. Cet appareil ne doit pas causer d’interférence
préjudiciable et
2. L’appareil doit accepter toute interférence
reçue, y compris les interférences qui peuvent
causer un fonctionnement non désiré.
Règlement de la FCC
Cet équipement a été testé et jugé compatible
avec les limites s’appliquant aux appareils
numériques de la classe B, conformément à
l’article 15 du règlement de la FCC. Ces limites ont
été dénies pour fournir une protection raisonna-
ble contre les interférences nuisibles dans le cadre
d’une installation résidentielle. Cet équipement
génère, utilise et peut émettre de l’énergie
radiofréquence et, s’il n’est pas installé ni utilisé
conformément aux instructions, peut causer des
interférences gênantes pour les communications
radio.
Rien ne garantit toutefois que des interférences
ne surviendront pas dans une installation
particulière. Si cet équipement cause des
interférences nuisibles pour la réception de la
radio ou de la télévision, ce qui peut être
déterminé en mettant l’équipement hors tension
puis sous tension, l’utilisateur devra essayer de
corriger ces interférences en eectuant une ou
plusieurs des opérations suivantes :
Déplacez l’antenne de réception.
Augmentez la distance entre l’équipement et le
récepteur.
Branchez l’équipement à une prise d’un circuit
autre que celui sur lequel le récepteur est
branché.
Consultez le détaillant ou un technicien de
radiotélévision expérimenté.
Canada:
L’émetteur/récepteur exempt de licence contenu
dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement
économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionne-
ment.
CAN ICES-3(B)/NMB-3(B)
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites
d’exposition aux radiations dénies par le Canada
pour des environnements non contrôlés.
Cet émetteur ne doit pas être installé au même
endroit ni utilisé avec une autre antenne ou un
autre émetteur.

8 Trademarks
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by MMD Hong
Kong Holding Limited is under license. Other
trademarks and trade names are those of their
respective owners.
Bluetooth
Siri is a trademark of Apple Inc., registered in the
U.S. and other countries.
Siri
Google and Google Play are trademarks of
Google LLC.
Google

9 Frequently asked
questions
My Bluetooth headset does not turn on.
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with my
Bluetooth device.
The Bluetooth is disabled. Enable the Bluetooth
feature on your Bluetooth device and turn on the
Bluetooth device before you turn on the headset.
Pairing does not work.
• Put both earpieces into charging box.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Porsche Design PDT60” from the Bluetooth
list.
• Pair your headset (see ‘Pair the
headset with your Bluetooth device
at the rst time’ on page 6).
The Bluetooth device cannot nd the headset.
• The headset may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
• Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the Bluetoot device again as
described in the user manual. (see
‘Pair the headset with your Bluetooth
device at the st time’ on page 6).
My Bluetooth headset is connected to a Bluetooth
stereo enabled mobile phone, but music only plays
on the mobile phone speaker.
Refer to the user manual of your mobile phone.
Select to listen to music through the headset.
The audio quality is poor and crackling noise can be
heard.
• The Bluetooth device is out of range.
Reduce the distance between your
headset and Bluetooth device, or
remove obstacles between them.
• Charge your headset.
The audio quality is poor when streaming from the
mobile phone is very slow, or audio streaming does
not work at all.
Make sure your mobile phone not only supports
(mono) HSP/HFP but alos supports A2DP and is
BT4.0x (or higher) compatible (see ‘Technical data’
on page 10).