PORTOR INDUSTRY PORTOR LIGHTING PT-MSH-PR User manual

PT-MSH-PR
PIR Motion Sensor
Type:Project Name:
www.portorlighting.com Specication subject to change without notice
Notes: Date:
SENSITIVITY: CEILING MOUNT: 100% 75% 50% 25%
Page 1/2
DESCRIPTION
The PT-MSH-PR mounts in an indoor lighting xture and provides multi-level control based
on motion. The occupancy sensors are designed to mount to a light xture and control one
load in that xture. When motion is detected within the sensor’s coverage area, the relay in
the sensor closes, and lighting loads are automatically turned on.
TECHNICAL SPECIFICATION
OPERATING VOLTAGE 120-347VAC, 50Hz/60Hz
STAND-BY POWER ≤1W (230VAC)
MAX LOAD
120V:3.3A/400W(Control Gear); 800W Ballast or Incandescent
230V:3.5A/800W(Control Gear); 1600W(Ballast or Incandescent)
347V:1.0A/350W(Control Gear); 700W Ballast or Incandescent
CONTROL METHOD 1-10V Dimm, ON/OFF
STAND-BY PERIOD 0s/10s/30s/1min/5min/10min/30min/60min/+∞
STAND-BY DIMMING LEVEL 10%/20%/30%/50%
PIR WAVE LENGTH 5-14um
PEAK OUTPUT SIGNAL ≥3500mW
PIR SENSITIVITY ≥3200V/W
DETECTION AREA 25%/50%/75%/100%
HOLD TIME 5s/30s/1min/3min/5min/10min/20min/30min
DAYLIGHT THRESHOLD 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
MOUNTING HEIGHT up to 8-12M/ 26.24-39.37ft (ceiling mounted)
DETECTION RANGE Radius 12M/39ft Max
MOTION DETECTION 0.5~1m/s
DETECTION ANGLE <120º (Without Glass Cover)
IP RATING IP20
OPERATING TEMP. -4°F ~ 140°F (-20°C ~ 60°C)
WARRANTY 3 years limited
MSH-RC2
Intelligent Remote Control Unit
(Needed to program motion sensor,
sold separately)
1. We reserve the right to necessarily modify any incorrect words or pictures or technical parameters.
2. Do NOT rework the sensor without permission or authorization, otherwise the contract clauses guaranteed will be invalid immediately.
DEFAULT PROGRAMMING: Detection Area 50%, Hold time 5S, Daylight Threshold Disable, Standby Period 0S, Standby Dimming Level 10%
ATTENTION
3.18” 2.16”
1.85” .78”
32.8'
26.3'
19.7'
13.1'
6.5'
0
6.5'
13.1'
19.7'
26.3'
32.8'
32.8'
26.3'
19.7'
13.1'
6.5'
0
6.5'
13.1'
19.7'
26.3'
32.8'
32.8'
26.3'
19.7'
0
39.4'
45.9'
32.8'
26.3'
19.7'
39.4'
45.9'
Detection Angle <120º (w/o glass cover)
Mounting height 3m/9.84 ft
Nominal movement 1m/sec., 13.28 ft/sec
Detection area 100%, 50%
Detection Angle <120º (w/o glass cover)
Mounting height 6m/19.7 ft
Nominal movement 1m/sec., 13.28 ft/sec
Detection area 100%, 75%, 50%. 25%
Detection Angle <120º (w/o glass cover)
Mounting height 12m/39.4 ft
Nominal movement 1m/sec., 13.28 ft/sec
Detection area 100%, 75%, 50%. 25%

PT-MSH-PR
PIR Motion Sensor
Type:Project Name:
www.portorlighting.com Specication subject to change without notice
Notes: Date:
Page 2/2
APPLICATIONS:
1. Do NOT mount it outdoor, in case
the outdoor temperature disturbs it.
2. Do NOT have it at places with
suddenly changed temperature
or airflow.
3. Do NOT have shelves between
sensor to the presence area.
The sensor will turn ON light once it
detects heat.
With enough ambient brightness, sensor
will keep the light OFF even though it
detects heat.
With enough ambient brightness, sensor
will keep the light OFF even though it
detects heat.
When ambient brightness gets lower
than the preset daylight lux level, the
sensor will turn ON light once it detects
heat in the area.
When ambient brightness gets lower
than the preset daylight lux level, the
sensor will turn ON light once it detects
heat in the area.
After heat leaves the area, the sensor
will keep light 100% ON for a hold-time
period, then turn OFF light automatically.
The sensor will dim light to standby
dimming level and keep for a standby
period after hold time.
The sensor will keep light 100% ON for a
hold time period after heat leaves the
area.
The sensor will dim light to standby
dimming level and keep for a standby
period after hold time.
The sensor will turn OFF light if no heat
detected during the standby period;
With heat presence, it will turn ON light
immediately.
The sensor will turn OFF light if no
heat detected during the standby
period; With heat presence, it will
turn ON light immediately.
APPLICATION:
ON/OFF Function: If the standby period is preset as 0S, the sensor will turn OFF the light automatically after hold-time.
DIMMABLE Function
DIMMABLE ON/OFF
DAYLIGHT Disable: If daylight threshold is preset as disable, the sensor will turn ON light once it detects heat regardless of ambient brightness.
WIRING DIAGRAMS:
HOLD-TIME
HOLD-TIME
HOLD-TIME STAND-BY
STAND-BY

BUTTON FUNCTION PERFORMANCE
ON/OFF Turn ON or OFF the sensor.
MW/PIR Exchange from Microwave detection to PIR detection,
for future use.
RESET
Press it to start detection programming; before pressing any
other buttons, the screen shows default programming
(Detection Area 100%, Holdtime SS, Daylight Disable, Standby
Dimming 10%, Standby Period OS)
START
Press it before you try to memorize program into the remote;
After pressing it, Son the screen will blink and keeping blinking
while making the program.
MEMORY Press it after programming, the blinking Swill become a solid
M, that means the program has been well memorized.
APPLY Press it to deliver the preset program to the specic sensors;
every presswill make the whole screen blink gently.
DETECTION AREA
Also known as “sensitivity”, 100% means the highest sensitivity
and longest distance. Press it, specic icon on the screen will
blink and press the + - buttons to adjust.
HOLD TIME
The period that light will stay illuminated 100% after no mo-
tion’s detected; Press it, specic icon on the screen will blink
and press the +- buttons to adjust.
DAYLIGHT
THRESHOLD
The preset lux level to compare with ambient brightness when
motion gets detected; Press it, specic icon on the screen will
Threshold blink and press the + - buttons to adjust.
STAND-BY PERIOD
The period after holdtime, during which the light keeps standby
dimming level; Press it, specic icon on the screen will blink
and press the + - buttons to adjust.
STAND-BY
DIMMING LEVEL
After holdtime, the light will dim from 100% to optional
standby dimming levels; Press it, specic icon on the screen
will blink and press the + -buttons to adjust.
UP
The main functional buttons to adjust the factors to wanted
level.
DOWN
POWER
Supports to manually change dimming output in detection
mode; Press it, specic icon on the screen will blink and press
the + - buttons to adjust.
TEST MODE
Supports to check if the sensor works correctly with a short
2S holdtime;Press it and the holdtime will change to 2S, and it
can’t be memorized
SENSOR PROGRAMMING
1. ON/OFF button to turn on the light
2. SCENE button to start programming
3. Choose functional button of detection area, see icon blinking on the LCD screen
display then use + - buttons to change
4. Same programming with all the other functional buttons of hold time, standby
dimming level, standby period and daylight threshold
5. Done and leave the remote
* Icon keeps blinking on the screen for 5S that means the program will then be kept
after 5S.
* Each press will make sensor dim down light then back to100%, it means remote
signal has been well received.
MEMORY AND APPLY
@the 1st sensor
1. ON/OFF button to turn on the light
2. SCENE button to start programming
3. START button
4. Choose functional button of detection area, see icon blinking on the LCD screen
display then use + - buttons to change
5. Same programming with all the other functional buttons of hold time, standby
dimming level, standby period and daylight threshold
6. MEMORY button
7. APPLY button
@the other sensors
1. ON/OFF button to turn on the light
2. SCENE button to start programming
3. APPLY button
MANUAL DIMMING ON/OFF mode
1. ON/OFF button to turn on the light
2. Press+- button to dim light directly, it dims from 10% to 100%
DIMMING mode
1. ON/OFF button to turn on the light
2. SCENE button to start programming
3. POWER button
4. +- buttons to dim light, but it only dims from 60% to 100%; 50% is one of the
standby dimming level options
* NUMBER ON LCD SCREEN DISPLAY MAY KEEP CHANGING 10%-100%.
MSH-RC2
SCREEN DISPLAY, MEMORY & APPLY
FUNCTION, OPTIONAL SCENES
HOW TO USE
MSH-RC2
Intelligent Remote Control Unit
Type:Project Name:
www.portorlighting.com Specication subject to change without notice
Notes: Date:
Page 1/1