Portwell WADE-8022 User manual

WADE-8022
Mini-ITX Board
User's Manual
Version 1.0
Copyright © Portwell, Inc., 2014. All rights reserved.
All other brand names are registered trademarks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List........................................................................................................... 1-2
1.3 Product Specification........................................................................................ 1-2
1.3.1 Mechanical Drawing................................................................................ 1-4
1.4 System Architecture.......................................................................................... 1-6
Chapter 2 Hardware Configuration ...........................................................................................2-1
2.1 Jumper Setting................................................................................................... 2-1
2.2 Connector Allocation...................................................................................... 2-10
Chapter 3 System Installation....................................................................................................3-1
3.1 Intel® Haswell Processor .................................................................................. 3-1
3.2 Main Memory.................................................................................................... 3-1
3.3 Installing the Mini-ITX Board Computer ...................................................... 3-2
3.3.1 Chipset Component Driver .................................................................... 3-2
3.3.2 Intel®Integrated Graphics Controller................................................... 3-3
3.3.3 Gigabit Ethernet Controller .................................................................... 3-3
3.3.4 Audio Controller...................................................................................... 3-3
3.4 Clear CMOS Operation .................................................................................... 3-3
3.5 EC WDT.............................................................................................................. 3-4
3.6 EC GPIO ............................................................................................................. 3-6
Chapter 4 BIOS Setup Information............................................................................................4-1
4.1 Entering Setup - Launch System Setup.......................................................... 4-1
4.2 Main .................................................................................................................... 4-2
4.3 Configutation..................................................................................................... 4-3
4.4 Boot ................................................................................................................... 4-23
4.5 Security ............................................................................................................. 4-25
4.6 Save & Exit ....................................................................................................... 4-26
Chapter 5 Troubleshooting........................................................................................................5-1
5.1 Hardware Quick Installation........................................................................... 5-1
5.2 BIOS Setting ....................................................................................................... 5-3
5.3 FAQ ..................................................................................................................... 5-4

Preface
How to Use This Manual
The manual describes how to configure your WADE-8022 system board to meet
various operating requirements. It is divided into five chapters, with each chapter
addressing a basic concept and operation of Mini-ITX Board.
Chapter 1: System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this series
model of Mini-ITX Board.
Chapter 2: Hardware Configuration. Show the definitions and locations of Jumpers
and Connectors that you can easily configure your system.
Chapter 3: System Installation. Describes how to properly mount the CPU, main
memory and Compact Flash to get a safe installation and provides a programming
guide of Watch Dog Timer function.
Chapter 4: BIOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
Chapter 5: Troubleshooting. Provide various of useful tips to quickly get
WADE-8022 running with success. As basic hardware installation has been
addressed in Chapter 3, this chapter will basically focus on system integration issues,
in terms of backplane setup, BIOS setting, and OS diagnostics.
The content of this manual is subject to change without prior notice. These changes
will be incorporated in new editions of the document. The vendor may make
supplement or change in the products described in this document at any time.

System Overview
WADE-8022 User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market and a
member of the Intel®Embedded and Communications Alliance (Intel®ECA),
announced today the Portwell WADE-8022 adopting the Mini-ITX form factor. The
WADE-8022 of the Intel®platform will provide high performance and flexibility for
functional expansion, such as Gaming, Kiosk, DS, Medical, Defense, Industrial
automation and control applications.
Haswell mobile processors is the next major architecture from Intel®. The
WADE-8022 supports the latest Intel®Haswell mobile processors in BGA1364
package which has memory and PCI Express controller integrated to support
2-channel DDR3L memory and PCI Express 3.0 lanes providing great graphics
performance. Intel®Haswell mobile processor is one of the most powerful and energy
efficient CPU in the world. Portwell have taken advantage of such technology to
furnish a series of products that can meet multiple industrial requirements such as
cost-effective of CPU performance or industrial systems.
WADE-8022 is based on the Intel®Haswell mobile processor with Intel®QM87
chipset.
The Intel®QM87 Express Chipset, when combined with a processor from the Intel®
Dual Core/Quad Core mobile processor family, delivers smart security, cost saving
manageability, and Intel® ligent performance for business platforms. WADE-8022 is
the first Portwell off-the-shelf product for by Intel®QM87 Express Chipset, it can be
an embedded solution and a good platform for customer to integrate it to the
embedded system.
WADE-8022 showcased one of Portwell upcoming motherboard for the Intel®’s
Haswell mobile processors. The WADE-8022 is based on the forthcoming Intel®
QM87 chipset and supports the new BGA1364 type. This board has lots of features,
including supports total 4x SATA 6.0 Gbps storage specification , allows RAID 0/1/5
and 10. supports the latest PCIe 3.0 (one PCI-Express x16 slot) devices for double
speed and bandwidth which enhances system performance, two long-DIMM
memory slot for DDR3L SDRAM up to 16GB, support total 10 USB ports (4x USB 3.0
on rear I/O, 6x USB 2.0 on board header), VGA / HDMI / DVI-D / DP / LVDS, two
Gigabit Ethernet and Dual mini-PCIe slot support mSATA and normal storage.

System Overview
WADE-8022 User’s Manual 1-2
1.2 Check List
The WADE-8022package should cover the following basic items
9One WADE-8022Mini-ITX Main Board
9One SATA Cable
9One I/O Shield bracket
9One Installation Resources CD-Title
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintenance.
1.3 Product Specification
zMain Processor
Intel®mobile BGA processor
zChipset
Intel®QM87 chipset
zSystem BIOS
AMI BIOS
zMain Memory
Two 204 -pin DDR3 SODIMM socket support DDR3L up to 16GB dual channel
1333/1600 MHz memory
zExpansion Interface
One PCIex16
- Two Mini-PCIe slot(support mSATA and normal SSD storage)
- One PCIe x1 gold finger(include 2x PCI x1 signal)
zSATA Interface
Four SATA 6Gb ports
zSerial Port
Support total six comports(one RS232 and one RS232/422/485 on rear I/O，three
RS232 and one RS232/422/485 on board header)
zUSB Interface
Support Ten USB (Universal Serial Bus) ports, four USB 3.0 ports on rear I/O and
six USB 2.0 ports on board header for internal devices
zAudio Interface
Line-Out Audio Jack on Rear I/O, Mic-In, Line-In on board header
zReal Time Clock/Calendar (RTC)
Support Y2K Real Time Clock/Calendar

System Overview
WADE-8022 User’s Manual 1-3
zWatch Dog Timer
Support WDT function through software programming for enable/disable and
interval setting
- General system reset
zOn-board Ethernet LAN
Two Gigabit Ethernet (10/100/1000 Mbits/sec) LAN ports using Intel®
WGI217LM
WGI210AT GbE Ethernet Controller
zHigh Drive GPIO
One pin-header for 8 bit GPIO(4bit in & 4bit out)
zSystem Monitoring Feature
Monitor system temperature and major power sources.
zOutline Dimension (L x W)
170mm(6.69’’) x 170mm(6.69’’)
zPower Requirements
Item Power ON
Full Loading
1
0M
in
Full Loading
30M
in
System +12V 1.71 A 1.98 A 2.23 A
USB Loading Test (2.0) 4.86 V/ 510 mA
USB Loading Test (3.0) 4.82 V/ 970 mA
zConfiguration
CPU Type Intel®Celeron CPU 2000E @ 2.20GHz L3: 2Mbytes
SBC BIOS Portwell, Inc. WADE-8022 TEST BIOS ( 40820T00 )
EC Version 40717T00 ( 07/17/2014 )
Memory WARIS DDR3L SO-DIMM 1600 1.35V/8GB*1
(Skhynix H5TC4G83AFR )
VGA Card Onboard Intel®HD Graphics
VGA Driver Intel®HD Graphics Version: 10.18.10.3496
LAN Card Onboard Intel®Ethernet Connection I217-LM
LAN Driver Intel®Ethernet Connection I217-LM Version: 12.11.96.1
LAN Card Onboard Intel®I210AT Gigabit Network Connection
LAN Driver Intel®I210AT Gigabit Network Connection Version: 12.11.97.0
Audio Card Onboard Realtek ALC886 High Definition Audio
Audio Driver Realtek ALC886 High Definition Audio Version: 6.0.1.7246
Chip Driver Intel®Chipset Device Software Version: 9.4.0.1027
USB 3.0 Driver Intel®USB3.0 eXtensible Host Controller Version: 6.2.9200.16384
SATA HDD WD WD1002FAEX 1TB
DVDROM LION-ON IHAS324 DVD-ROM
Power Supply Seasonic SSA-0651-1 DC 12V

System Overview
WADE-8022 User’s Manual 1-4
zOperating Temperature
0 °C ~ 60 °C
zStorage temperature
-20 ~ 80 °C
zRelative Humidity
0% ~ 90%, non-condensing
1.3.1 Mechanical Drawing

System Overview
WADE-8022 User’s Manual 1-5

System Overview
WADE-8022 User’s Manual 1-6
1.4 System Architecture
All of details operating relations are shown in WADE-8022 System Block Diagram.
WADE-8022 System Block Diagram

Hardware Configuration
WADE-8022 User’s Manual 2-1
Chapter 2
Hardware Configuration
This chapter gives the definitions and shows the positions of jumpers, headers
and connectors. All of the configuration jumpers on WADE-8022 are in the proper
position.
2.1 Jumper Setting

Hardware Configuration
WADE-8022 User’s Manual 2-2

Hardware Configuration
WADE-8022 User’s Manual 2-3
Jump Setting List
is mean default
JP1: GPIO Power select Connector
PIN No. Signal Description
1-2 5V
2-3 3V (Default) 
JP2: Dual channel LVDS VDD voltage Select
PIN No. Signal Description
1-2 VDD voltage 3.3V (Default) 
5-6 VDD voltage 5V
JP3: LVDS BL Enable voltage Select
PIN No. Signal Description
1-3, 2-4 5V, Active High (Default) 
1-3, 4-6 12V, Active High
3-5,2-4 5V, Active Low
3-5,4-6 12V, Active Low
JP4: WDT Function Select
PIN No. Signal Description
1-2 short WDT Function enable (Default) 
1-2 open WDT Function disable
JP5: ATX / AT Mode Select
PIN No. Signal Description
1-2 short ATX emulation AT mode
1-2 open ATX mode 

Hardware Configuration
WADE-8022 User’s Manual 2-4
J9: Audio MIC/Line-in/Line-out Connector
PIN No. Signal Description PIN No. Signal Description
1 MIC- in Left Channel 2 Line-in Left Channel
3 Analog Ground 4 Line-in Right Channel
5 Line-out Left Channel 6 Analog Ground
7 Line-out Right Channel 8 MIC- in Right Channel
J10: ATX 4Pin 12V Power Connector
PIN No. Signal Description
1 Ground
2 Ground
3 +12V
4 +12V
J11: 8Bit GPIO Connector
PIN No. Signal Description PIN No. Signal Description
1 LPC_GPJ0 2 LPC_GPE0
3 LPC_GPJ1 4 LPC_GPE7
5 LPC_GPJ2 6 LPC_GPC0
7 LPC_GPJ3 8 LPC_GPG0
9 GND 10 VCC
J13: LVDS Power Connector
PIN No. Signal Description
1 VCC
2 BL_BRIGHT
3 +12V
4 Ground
5 BL_ENABLE

Hardware Configuration
WADE-8022 User’s Manual 2-5
J14: TPM(Trusted Platform Module) Connector
PIN No. Signal Description PIN No. Signal Description
1 PCLK_TPM 2 GND
3 LFRAME# 4 N/C
5 SIO2_PLTRST# 6 VCC
7 LAD3 8 LAD2
9 VCC3 10 LAD1
11 LAD0 12 GND
13 SMB_CLK_MAIN 14 SMB_DATA_MAIN
15 3VSB 16 SERIRQ
17 GND 18 N/C
19 LPCPD# 20 N/C
J15: Dual channel LVDS Connector
PIN No. Signal Description PIN No. Signal Description
1 VDD 2 VDD
3 LCD1DO0+ 4 LCD1DO0-
5 LCD1DO1+ 6 LCD1DO1-
7 LCD1DO2+ 8 LCD1DO2-
9 LCD1DO3+ 10 LCD1DO3-
11 LCD1CLK+ 12 LCD1CLK-
13 LCLK1 14 LDATA1
15 Ground 16 Ground
17 LCD2DO0+ 18 LCD2DO0-
19 LCD2DO1+ 20 LCD2DO1-
21 LCD2DO2+ 22 LCD2DO2-
23 LCD2DO3+ 24 LCD2DO3-
25 LCD2CLK+ 26 LCD2CLK-
27 N/C 28 N/C
29 Ground 30 Ground

Hardware Configuration
WADE-8022 User’s Manual 2-6
J16/J17/J18/J19: COM3/COM4/COM5/COM6 Serial Port Connector
PIN No.
Signal Description PIN No.
Signal Description
1 DCD (Data Carrier Detect) 2 RXD (Receive Data)
3 TXD (Transmit Data) 4 DTR (Data Terminal
Ready)
5 GND (Ground) 6 DSR (Data Set Ready)
7 RTS (Request to Send) 8 CTS (Clear to Send)
9 RI (Ring Indicator) 10 N/C
J20: Clear CMOS
PIN No. Signal Description
1-2 Normal 
2-3 Clear CMOS
J22/J26: SATA Power Connector
Pin No. Signal Description
1 +12V
2 GND
3 GND
4 VCC

Hardware Configuration
WADE-8022 User’s Manual 2-7
J23/J24/J25: External USB Connector
PIN No.
Signal Description PIN No.
Signal Description
1 5V Dual 2 5V Dual
3 USB- 4 USB-
5 USB+ 6 USB+
7 Ground 8 Ground
9 10 N/C
J27: SMBus Connector
PIN No. Signal Description
1 SMBus_CLK
2 N/C
3 Ground
4 SMBus_DAT
5 +5V
J32: SYSTEM FAN Power Connector
PIN No. Signal Description
1 Ground
2 Fan speed control
3 Fan on/off output

Hardware Configuration
WADE-8022 User’s Manual 2-8
J37: Front Panel System Connector
PIN No.
Signal Description PIN No.
Signal Description
1 PWR_LED(+) 2 Speaker(+)
3 PWR_LED(-) 4 GND
5 J4 LAN1_ACT(+) 6 N /C
7 J4 LAN1_LINK(-) 8 Speaker(-)
9 J5 LAN2_LINK(-) 10 GND
11 J5 LAN2_ACT(+) 12 Power Button
13 HDD_LED(+) 14 RESET Button
15 HDD_LED(-) 16 GND
J38: CPU FAN Power Connector
PIN No. Signal Description
1 Ground
2 +12V
3 Fan on/off output
4 Fan Speed control
J39:PS/2 Keyboard/Mouse Pin Header
PIN No.
Signal Description PIN No.
Signal Description
1 Mouse Data 2 Keyboard Data
3 N/C 4 N/C
5 Ground 6 Ground
7 PS2 Power 8 PS2 Power
9 Mouse Clock 10 Keyboard Clock

Hardware Configuration
WADE-8022 User’s Manual 2-9
J41: SPI Bus Select Header
PIN No. Signal Description
1-3, 2-4, 7-9, 8-10 CFEX
3-5, 4-6, 9-11, 10-12 Normal
SW1: LVDS GPIO Switch Select
ON : 0 ; OFF : 1
Default : 0001
Pin No. Signal Description
1 GP0
2 GP1
3 GP2
4 GP3

Hardware Configuration
WADE-8022 User’s Manual 2-10
2.2 Connector Allocation
I/O peripheral devices are connected to the interface connectors.
Connector Function List
Connector Function Remark
J1 DC Jack
J2 Audio Line Out Connector
J3 Serial port Connector (Top-COM2,
Bot-COM1)
COM2 Support 232/422/485
J4 Display Port Connector (DP port)
J5 DVI-I Connector Support Dual (DVI-D,VGA)
Link
J6 HDMI Connector
J7 USB/100+Giga Lan Connector
(LAN2) I210IT
J8 USB/100+Gi
g
a Lan Connector
(LAN1) I217LM
J9 Audio MIC/Line-in/
Line-out Connector
J10 ATX 4Pin 12V Power Connector
J11 8Bit GPIO Connector
J13 LVDS Power Connector
J14 TPM(Trusted Platform Module)
Connector
J15 Dual channel LVDS Connector
J16、J17、J18、
J19
COM3/COM4/COM5/COM6
Serial Port Connector
J20 Clear CMOS Select HEADER
J21 PCI-E x16 Slot Support PCI-E Gen3
J22、J26 SATA Power Connector
J23、J24、J25 External USB Connector
J27 SMBus Connector
J28 Mini PCIe Slot Only Support Mini PCIe
J29 Mini PCIe Slot Only Support mSATA
J30、J31 SO-DIMM Slot Only Support
DDR3L Memory
J32 System FAN Power Connector
J33、J34、J35、
J36
SATA Connector(6Gb/s)
J37 Front Panel System Connector
J38 CPU FAN Power Connector
J39 PS/2 Keyboard/Mouse Pin Header

Hardware Configuration
WADE-8022 User’s Manual 2-11
J40 CFEX Card slot
J41 SPI Select HEADER