Portwell NANO-6060 User manual

NANO-6060
NANO-ITX Board
User's Manual
Version 1.0
Copyright © Portwell, Inc., 2013. All rights reserved.
All other brand names are registered trademarks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List........................................................................................................... 1-1
1.3 Product Specification........................................................................................ 1-1
1.4 System Configuration....................................................................................... 1-3
1.4.1 Mechanical Drawing................................................................................ 1-4
1.5 System Architecture.......................................................................................... 1-5
Chapter 2 Hardware Configuration ...........................................................................................2-1
2.1 Jumper Setting................................................................................................... 2-1
2.2 Connector Allocation........................................................................................ 2-5
Chapter 3 System Installation....................................................................................................3-1
3.1 Intel® Valleyview CPU .................................................................................... 3-1
3.2 Main Memory.................................................................................................... 3-1
3.3 Installing the Single Board Computer............................................................ 3-1
3.3.1 Chipset Component Driver .................................................................... 3-2
3.3.2 Intel® HD Graphics 4600 ........................................................................ 3-2
3.3.3 Intel LAN I210IT Gigabit Ethernet Controller..................................... 3-2
3.3.4 Realtek ALC892 HD Audio Controller................................................. 3-2
3.4 Clear CMOS Operation .................................................................................... 3-3
3.5 WDT Function ................................................................................................... 3-4
3.6 GPIO.................................................................................................................... 3-6
Chapter 4 BIOS Setup Information............................................................................................4-1
4.1 Entering Setup -- Launch System Setup ........................................................ 4-1
4.2 Main .................................................................................................................... 4-2
4.3 Advanced ........................................................................................................... 4-6
4.4 Others................................................................................................................ 4-18
4.5 Security ............................................................................................................. 4-21
4.6 Boot ................................................................................................................... 4-22
4.7 Exit..................................................................................................................... 4-23
Chapter 5 Troubleshooting........................................................................................................5-1
5.1 Hardware Quick Installation........................................................................... 5-1
5.2 BIOS Setting ....................................................................................................... 5-2
5.3 FAQ ..................................................................................................................... 5-2
Appendix A
Appendix B

Preface
How to Use This Manual
The manual describes how to configure your system board to meet various operating
requirements. It is divided into five chapters, with each chapter addressing a basic
concept and operation of Single Host Board.
Chapter 1 : System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this series
model of single host board.
Chapter 2 : Hardware Configuration. Shows the definitions and locations of Jumpers
and Connectors that you can easily configure your system.
Chapter 3 : System Installation. Describes how to properly mount the CPU, main
memory and Compact Flash to get a safe installation and provides a programming
guide of Watch Dog Timer function.
Chapter 4 : BIOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
Chapter 5 : Troubleshooting. Provides various useful tips to quickly get its running
with success. As basic hardware installation has been addressed in Chapter 3, this
chapter will basically focus on system integration issues, in terms of backplane setup,
BIOS setting, and OS diagnostics.
The content of this manual is subject to change without prior notice. These changes
will be incorporated in new editions of the document. Portwell may make
supplement or change in the products described in this document at any time.
Updates to this manual, technical clarification, and answers to frequently asked
questions will be shown on the following web site : http://www.portwell.com.tw/.

System Overview
NANO-6060 User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market and a
member of the Intel® Communications Alliance, has launched its new NANO-ITX
form factor based NANO-6060 for embedded system board (ESB) that offers lower
power consumption, robust computing power and with longevity support.
The NANO-6060 is specifically designed to operate at very low power consumption
and low heat, so it can be a truly fanless configuration and battery operated. Base on
Intel® ATOM E3800 family SoC, the NANO-6060 supports one DDR3L SODIMM
socket up to 4GB system memory and comes with two SATA II, one hald size
Mini-PCIe socket, multiple display by VGA, DP and 24-bit LVDS, two gigabit
Ethernet, one micro SD socket and Six USB ports (two for 2.0, four for 3.0). It also built
with DC 12V or ATX 12V input.
Base on leading Intel® Atom solution, NANO-6060 is a compact and low power
dissipation board for Digital Signage, Digital Security Surveillance (DSS) and Medical
applications…etc.
1.2 Check List
The NANO-6060 package should cover the following basic items
3One NANO-6060 NANO-ITX Main Board
3One passive Heatsink
3One Installation Resources CD-Title
3One SATA cable
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintain
1.3 Product Specification
zMain Processor
- On board Intel® ATOMTM E3800 family SoC
zSystem BIOS
- Phoenix uEFI BIOS
zMain Memory
- One 204pin DDR3L SODIMM socket on board up to 4GB system memory

System Overview
NANO-6060 User’s Manual 1-2
zPower input
- DC 12V input on rear I/O
- 4pin +12V power connector on board
- (DC 12V Jack and 4pin power connector can’t be used at the same time)
zSerial Port
- Support one RS232/422/485 port on-board connector (adjust by bios)
zUSB Interface
- Support six USB (Universal Serial Bus) ports. Four are USB 3.0 (two on rear I/O
and two on board header for internal devices.). Two are USB 2.0 ports.
zSATA Interface
- Support two SATA II ports
zCOM port
- Support one on board RS232/422/485 port (select by bios)
zSD interface
- Support one micro SD socket
zAudio Interface
- Line-Out Audio Jack on rear I/O
- On board pin header for Line-out, Line-in , Mic-in
zWatch Dog Timer
- Support WDT function through software programming for enable/disable and
interval setting
- General system reset
zDisplay
- Support multiple display by DP (rear I/O), VGA (on-board connector) and dual
channel 24-bit LVDS
zOn-board Ethernet LAN
- Two Gigabit Ethernet (10/100/1000 Mbits/sec) LAN port using Intel I210IT
PCI-Expressx1 interface GbE Controller
- Support two GbE LAN on E3827 & E3845 sku, only support one GbE LAN on
E3815 sku
- Support Wake on LAN function
zPCI Express slot
- Support one PCIE x1 slot
zHigh Drive GPIO
- On-board programmable 8-bit Digital I/O interface
zSystem Monitoring Feature
- Monitor system temperature and major power sources.
zOutline Dimension (L x W)
- 120mm(4.72’’) x 120mm(4.72’’)

System Overview
NANO-6060 User’s Manual 1-3
1.4 System Configuration
System Configuration
CPU Type Intel® Atom™ CPU E3845 1.91GHz L2 Cache 1024KB
SBC BIOS Phoenix BIOS Portwell ,Inc NANO-6060
Test BIOS(31025T01)
EC Version:R00.E00
Memory WARIS DDR3L SO-DIMM 1333 1.35V/4GB
(Hynix H5TC2G83EFR)
VGA Card Onboard Intel® HD Graphics
VGA Driver Intel® HD Graphics Version:10.18.10.3309(09/16/2013)
LAN Card Onboard Intel® I210 Gigabit Network Connection
LAN Driver Intel® I210 Gigabit Network Connection Version:12.7.28.0
LAN Card Onboard Intel® I210 Gigabit Network Connection #2
LAN Driver Intel® I210 Gigabit Network Connection
#2 Version:12.7.28.0
Audio Card Onboard Realtek ALC892 High Definition Audio
Audio Driver Realtek ALC892 High Definition Audio Version:6.0.1.6873
Chip Driver Intel® Bay Trail-M/D SOC Chipset Device
Software Version:9.4.4.1005
Display Intel corporation version:6.16.0.3.124(09/10/2013)
USB 3.0 Driver Intel® USB 3.0 eXtensible Host
Controller-0100 Version:6.2.9200.16656(Micrsoft)
SATA HDD Seagate ST3500411SV 500GB
CDROM ASUS DRW-24D3ST
Power Supply Portwell ORION-D4601 460W
zPower Consumption test: Run Burning Test V7.1
RUN time: 10 / 30 Minutes.
Item Power ON
Full Loading
10Min
Full Loading
30Min
DC +12V 0.96 1.24 1.20
zOperating Temperature
-40°C ~ 80°C
zStorage temperature
-40 ~ 80 °C
zRelative Humidity
0% ~ 95%, non-condensing

System Overview
NANO-6060 User’s Manual 1-4
1.4.1Mechanical Drawing

System Overview
NANO-6060 User’s Manual 1-5
1.5 System Architecture
All of details operating relations are shown in NANO-6060 System Block Diagram.
NANO-6060 System Block Diagram

Hardware Configuration
NANO-6060 User’s Manual 2-1
Chapter 2
Hardware Configuration
This chapter gives the definitions and shows the positions of jumpers, headers and
connectors. All of the configuration jumpers on NANO-6060 are in the proper
position. The default settings shipped from factory are marked with an asterisk (♣).
2.1 Jumper Setting
In general, jumpers on the single board computer are used to select options for
certain features. Some of the jumpers are designed to be user-configurable, allowing
for system enhancement. The others are for testing purpose only and should not be
altered. To select any option, cover the jumper cap over (SHORT) or remove (NC) it
from the jumper pins according to the following instructions. Here NC stands for
“Not Connect”
Figure 2-1 NANO-6060 Jumper and Connector Locations

Hardware Configuration
NANO-6060 User’s Manual 2-2
JP1: GPIO4~7 Voltage Level Selection
JP1 Function
1-2 Short 5V ( output )
2-3 Short 3.3V ( Input ) Ì
JP3: LVDS Link Selection
JP3 Function
Short Dual Link Ì
Open Single Link

Hardware Configuration
NANO-6060 User’s Manual 2-3
JP5 : PANEL Voltage Selection
JP5 Function
1-3 Short VCC3 Ì
3-5 Short VCC
3-4 Short +12V
JP6: PANEL BACKLIGHT Selection
Pin No. Signal Description
1-3, 2-4 5V, Active High Ì
1-3, 4-6 12V, Active High
3-5,2-4 5V, Active Low
3-5,4-6 12V, Active Low

Hardware Configuration
NANO-6060 User’s Manual 2-4
JP7/JP8 : CMOS Clear
JP7/8 Function
1-2 Short Normal Operation Ì
2-3 Short Clear CMOS Contents
JP10 : LVDS Color Depth and Data Mapping
JP10 Function
2-4 Short 8-bit LVDS , VESA mapping Ì
1-3 , 2-4 Short 8-bit LVDS , JEIDA mapping
1-3 Short 6-bit LVDS , VESA and JEIDA mapping
1
3
24

Hardware Configuration
NANO-6060 User’s Manual 2-5
SW2 : Power on / BIOS Recovery selection 
SW2 Function
1-4 OFF ATX Ì
1-4 ON AT
2-3 OFF Recovery Disable Ì
2-3 ON Recovery Enable
2.2 Connector Allocation
I/O peripheral devices and Flash disk will be connected to these interface connectors
Connector Description Remark
J1 DC Jack +12V Input
J2 Audio Jack ( Line_out )
J3 DP Port
J4/J5 RJ45 Connector
J6 USB3 Connector
J7 External Audio (Mic + Line_in + Line_out )
Pin HDR.
4x2 pin header
J8 VGA Pin HDR. 5x2 pin header
J9 Front Panel Pin HDR 5x2 pin header
J10 General Purpose I/O Pin HDR 5x2 pin header
J11 RS232/422/485 Pin HDR 5x2 pin header
J12 ATX 4 Pin Connector +12V Input
J13 External USB3 Connector
J14 PCIe x 1 SLOT
J15 External USB2 Connector
J16 Mini PCIe Connector

Hardware Configuration
NANO-6060 User’s Manual 2-6
J17 DDR3 SO-DIMM Socket
J18 LVDS Connector
J19/J20 SATA Power Connector
J21/J22 SATA GEN2 Connector
J7 : External Audio Connector
PIN No. Signal Description PIN No.
Signal Description
1 MIC_L 2 Line_in_L
3 Ground 4 Line_in_R
5 Line_out_L 6 Ground
7 Line_out_R 8 MIC_R
1
2
J8 : VGA Connector
PIN No. Signal Description PIN No.
Signal Description
1 RED 2 SCL
3 GREEN 4 GND
5 BLUE 6 SDA
7 VSYNC 8 GND
9 HSYNC 10 +5V
1
2

Hardware Configuration
NANO-6060 User’s Manual 2-7
1
2
J9 : Front Panel Pin HDR(J9)
PIN No. Signal Description PIN No.
Signal Description
1 Ground 2 N/C
3 +5V 4 N/C
5 HDD_LED(+) 6 HDD_LED(-)
7 Reset (+) 8 Power On(-)
9 Reset (-) 10 Power On(+)
J10: General Purpose I/O Connector
PIN No. Signal Description PIN No.
Signal Description
1 GPIO0 2 GPIO4
3 GPIO1 4 GPIO5
5 GPIO2 6 GPIO6
7 GPIO3 8 GPIO7
9 Ground 10 +5V

Hardware Configuration
NANO-6060 User’s Manual 2-8
J11: RS-232/422/485 I/O Connector
PIN No. Signal Description PIN No.
Signal Description
1 DCD#/485D-/422T- 2 RXD#/485D+/422T+
3 TXD#/422R+ 4 DTR#/422R-
5 Ground 6 DSR#
7 RTS# 8 CTS#
9 RI# 10 N/C
J13 : External USB3 Connector
PIN No. Signal Description PIN No.
Signal Description
1 5V always 11 USB2_DP_#3
2 USB3_RXM_#1 12 USB_DM_#3
3 USB3_RXP_#1 13 Ground
4 Ground 14 USB3_TXP_#3
5 USB3_TXM_#1 15 USB3_TXM_#3
6 USB3_TXP_#1 16 Ground
7 Ground 17 USB3_RXP_#3
8 USB2_DM_#1 18 USB3_RXM_#3
9 USB2_DP_#1 19 5V always
10 Ground 20 Key( no pin )

Hardware Configuration
NANO-6060 User’s Manual 2-9
Note:
5V Dual is always available. It's supplied by either 5V VCC power source in normal
operation mode or 5V standby power source in standby mode.
J15 : External USB Connector
PIN No. Signal Description PIN No.
Signal Description
1 5V always 2 5V always
3 USB- 4 USB-
5 USB+ 6 USB+
7 Ground 8 Ground
9 Key( no pin ) 10 N/C
Note:
5V Dual is always available. It's supplied by either 5V VCC power source in normal
operation mode or 5V standby power source in standby mode.
1
2

Hardware Configuration
NANO-6060 User’s Manual 2-10
J18 : LVDS Connector
PIN No. Signal Description PIN No.
Signal Description
1 VDD_LVDS 2 VDD_LVDS
3 LVDSA_DATA0 4 LVDSA_DATA#0
5 LVDSA_DATA1 6 LVDSA_DATA#1
7 LVDSA_DATA2 8 LVDSA_DATA#2
9 LVDSA_DATA3 10 LVDSA_DATA#3
11 LVDSA_CLKP 12 LVDSA_CLKN
13 DDC_SCL 14 DDC_SDA
15 Ground 16 Ground
17 LVDSB_DATA0 18 LVDSB_DATA#0
19 LVDSB_DATA1 20 LVDSB_DATA#1
21 LVDSB_DATA2 22 LVDSB_DATA#2
23 LVDSB_DATA3 24 LVDSB_DATA#3
25 LVDSB_CLKP 26 LVDSB_CLKN
27 N/C 28 N/C
29 Ground 30 Ground
1
2
J19/J20 : SATA Power Connector
Pin No. Signal Description
1 +12V
2 Ground
3 Ground
4 +5V

Hardware Configuration
NANO-6060 User’s Manual 2-11
J23 : Battery Connector
Pin No. Signal Description
1 Battery Voltage
2 Ground
J24 : Back light Connector
Pin No. Signal Description
1 +5V
2 BL_CTRL
3 +12V
4 Ground
5 BL_Enable
1

Hardware Configuration
NANO-6060 User’s Manual 2-12
J25 : SMBUS Connector
Pin No. Signal Description
1 SMB_CLK
2 Key( no pin )
3 Ground
4 +5V
5 SMB_DATA