POSIFLEX SD-460Z/W User manual

Page 1
SD-460Z/W
UPGRADE KIT
USER’S MANUAL
Rev.: Original
I. Features
ISO 7811 Magnetic Stripe Reader with USB interface
Dual directional operation for MSR
3 tracks type MSR reads AAMVA and CA DMV card
Textured front surface
Built-in Optical Finger Print Sensor
Side-mounted on KS-62/68/69/72/77 series (SD-460Z) or KS-66/73 series (SD-460W)
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult his/her
dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Posiflex Technology, Inc. further disclaims
all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. the entire risk arising out of
the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the upgrade kit SD-460Z/W for the Posiflex fan free touch terminals KS
series. This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate the required security
specially involved in POS business, kiosk and hospitality operation. This manual covers the conceptual and operational aspects of these units. For technical
aspects involving opening of the unit or option implementation, it is only available to the authorized distributors.
The manufacturer of the SD-460Z/W series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the
rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through any of our web
sites: http://www.posiflex.com or http://www.posiflex.com.tw.
Copyright Posiflex Technology Inc. 2012
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technology, Inc. the publisher of this documentation
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc. an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II. Installation
1. Hardware Installation
1. Release the 2 screws on the back of the right side of the terminal to remove the
protective cover. Store the protective for future use.
2. Connect the cable found under the cover with the white connector inside SD-460.
3. Attach SD-460 to the terminal with the corresponding screw holes in alignment, and
then secure the 2 screws.
2. Driver Installation
1. MSR: The magnetic stripe reader connects to the host through USB port working as a USB
KB and also requires no driver installation except setting up the USB keyboard to be
enabled in system CMOS setup if the OS does not do it automatically. Refer to “Operation
Guide” for manipulation over the reader configuration.
2. Finger Print Sensor: To include the drivers for this sensor to perform finger print
registration or verification (authentication) in an AP requires the software programmer to
purchase and utilize its SDK (software developer’s kit). However, Posiflex delivers this
optical finger print sensor with its drivers. Please find in the mini CD delivered with SD-
460Z/W series except SD-460Z/W model or Product Information CD delivered with
Posiflex POS system the folder for “Posiflex Optical Finger Print Sensor”.
III. Operation Guide
1. Magnetic Stripe Reader
The MSR in SD-460Z/W series reads an ISO magnetic stripe card without driver. Yet, there
is a “MSR.EXE” program for SD-460Z/W model and a “Posiflex USB MSR Manager”
program for other model provided to control some parameter configuration for this MSR.
Through this program, you can enable/disable track, set up Alt+Num approach for ASCII
codes, and enable/disable Leading/Stop code. Please look for “USBMSR” and “SetUp” folders
in the mini CD delivered with SD-460Z/W or Product Information CD delivered with Posiflex
POS system to install the program or download it from our web site:
http://www.posiflex.com or http://www.posiflex.com.tw.
1
2
3
P/N: 19800902010

Page 2
2. Finger Print Sensor
a. Cautions
1. Never pour the glass cleaner directly on the sensor window
2. Never use alcohol-based cleaners
3. Never submerge the sensor in liquid
4. Never rub the window with an abrasive material, including paper
5. Do not poke the window coating with your fingernail or any hard item, such as a pen.
b. Principle
The finger print sensor software never stores fingerprint images. The finger print sensor
software creates a fingerprint template, which is a highly compressed and digitally encoded
mathematical representation of fingerprint features. This template is created when a user
registers a finger and is stored in an encrypted file. When the user later touches the fingerprint
reader to authenticate, a new template is created and compared to the “registered” template. If
there is a match, the authentication is successful.
c. Finger Print Recognition
In order for the sensor to acquire a good image of your finger, you must place the pad of
your finger but not the tip in the center of the sensor window, and apply gentle, even pressure.
Do not “roll” your finger as usually practiced in the traditional ink and paper fingerprint taking
technique. Pressing too hard will distort your fingerprint. Pressing too lightly will not expose a
large enough area of your finger. Also, make sure to hold your finger on the sensor until you
see the sensor light blink; this may take longer for dry fingers. Then, lift your finger. Although
you may use any finger with the sensor, your index finger of either hand works best. If the
sensor is capturing your finger image as indicated by the sensor blink and you have tried all the
above suggestions, you may need to reregister your finger.
d. Sensor Activation
The LED behaviors are described in the following table.
LED Color Description
Blue Finger print sensor on standby
Red Reading successfully
Failure to connect to a self-powered USB port will cause non-operation of the sensor. If
you activate your terminal’s power-saving functionality but your third party application does
not support this, then your fingerprint sensor will enter “sleep mode” even though your
workstation does not. If this occurs, you will need to reboot the system. Please check with your
application developer for compatibility.
e. Cleaning the Sensor
Depending on the amount of use, the sensor window may need to be cleaned periodically.
To clean it, apply the sticky side of a piece of adhesive cellophane tape on the window and peel
it away as in the drawing at right.
Under heavy usage, the window coating on some sensors may turn cloudy from the salt in
perspiration. In this case, gently wipe the window with a cloth (not paper) dampened with a
mild ammonia-based glass cleaner.
IV. SPECIFICATIONS
1. Reader Specifications
Applicable card type ISO 7811 JIS X 6302
Card feed method Manual Manual
Card feed direction Bi-direction Bi-direction
Read / write function Read only Read only
Card feed speed 5 to 55 inches/sec. 100 to 1200mm /sec.
Error rate < 0.5% < 0.1%
* Reader specs option must be specified upon ordering.
2. Card Data Specifications
Data standard IATA ABA THRIFT JISII
Track used Track 1 Track 2 Track 3 Rear section
Recording method F
2
F (FM) F
2
F (FM) F
2
F (FM) F
2
F (FM)
Recording density 210 BPI 75 BPI 210 BPI 210 BPI
Recording capacity 79 / 7 40 / 5 107 / 5 72 / 7
* Card data specs is decided by reading head type, and must be specified upon ordering.
3. Other Specifications
Standards AAMVA, CA DMV
Interface USB
Rated Voltage 5V DC
Rated Current 300 mA (Max)
Reading Head Single ISO head or Dual ISO Head or JISII head*
* Reading head type must be specified upon ordering.
警告使用者
警告使用者警告使用者
警告使用者
這是甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況 ，使用者會被要
求採取某些適當的對策。
T31454