POSIFLEX LM-6807U User manual

1
LM-6807U LM-6810U
Package Contents
Rear-Mount USB POS Monitor with Bracket (x 1)
ψ3-10L Self-Tapping Screw (x 4)
USB Cable (x 1)
User Manual (x 1)
Product Features
 USB interface monitor for system without secondary display
interface
 7” TFT LCD panel for LM-6807U and 10” one for LM-6810U
 LCD resolution up to 800 x 480 for LM-6807U and 1024 x
768 for LM-6810U
 Rear-mount for PS-3000 series terminal
LM-6807U/6810U
Rear-Mount USB POS Monitor
User Manual
19600990010 Ver. Original

2
Views of the LM-6807U/6810U
Front View
LM-6807U LM-6810U
Rear View
LM-6807U
LM-6810U
LCD
Screw Holes
Screw Holes
Power Button
Brightness-Up Button
Brightness-Down Button

3
Bottom View
LM-6807U
LM-6810U
Mounting the USB POS Monitor onto a POS Terminal
During Installation of the LM-6807U or LM-6810U USB POS
monitor, do NOT power ON your POS terminal. To mount the
monitor onto your PS-3000 series POS terminal, please apply 4
screws that are packed together with the USB POS monitor.
Before mounting the monitor, carefully read the following step-
by-step instruction on the display installation.
1. Remove the rear I/O cover of your
PS-3000 series POS terminal.
USB Port
DC-IN Power Jack USB Port

4
2. Take the monitor out of the LM-
6807U/6810U package box. Here,
LM-6807U is taken for example of
installation. Align the A type
connector of a USB cable with the
USB port of your ternminal.
3. Align the four screw holes formed on
the bracket of the monitor with the
four screws holes formed on the rear
side of the POS terminal.
4. Turn the four screws to the right to
tighten them.
5. Connect the B type connector of USB
cable to the USB port of the POS
monitor.
6. Tilt the POS monitor to a degree for next steps of installation
Align
Do NOT press the displaying
area of panel!

5
7. By using a diagonal cutting nipper, cut the cable-exit shield
off the rear I/O cover you removed from the POS terminal at
step 1.
8. Arrange the USB cable.
9. To arrange the USB cable of the display, make the cable go
through the cable exit of the rear I/O cover.

6
10. Align the two wedge tabs of the rear
I/O cover with the two wedged
portion of the rear plate of the
terminal, and then make the two
wedge tabs wedge respectively into
the two wedged portion of the rear
plate of the terminal.
11. Lever down the hook of the cover to
cover the rear I/O interface.
12. Determine that the USB POS monitor
is well mounted onto the POS
terminal.
13. For an optimal viewing angle, you can adjust the USB POS
monitor up and down around the directions A and B at the
angle of tilt from 0° to 45°.
A
B
Do NOT press the displaying area of panel!

7
Installing the USB Driver for LM-6807U/6810U
Refer to the following step-by-step instruction for the driver
installation.
1. Connect the USB POS monitor to your POS terminal by using
a USB cable.
2. Locate the “Drivers” folder in the
Local Disk (C:) of your POS
terminal, and double click it.
3. You will find the “SA_PD_LM”
folder and double click it.
4. Then double click the
“LM_USBMonitor” folder.
5. Double click the execution file
named DisplayLink_7.6M0 to start
step-by-step installation.

8
Specifications
LM-6807U LM-6810U
LCD Panel 7" TFT LCD 10" TFT LCD
Resolution 800 (H) x 480 (V) 1024 (H) x 768 (V)
Active Area 154.08 (H) x 85.92 (V) 196.61 (H) x 147.46 (V)
Pixel Pitch 0.1926 (H) x 0.1790 (V) 0.192 (H) x 0.192 (V)
Pixel
Arrangement RGB Vertical Stripe LVDS
Viewing
Angle
60/70/70/70 degree
(U/D/L/R)
70/70/70/60 degree
(U/D/L/R)
Contrast Ratio 500 : 1
Response
Time
25 ms (Raising) / 25 ms
(Falling)
20 ms (Raising) / 20 ms
(Falling)
Brightness 250 cd/m2 270 cd/m2
Display
Interface USB
Power Supply
Powered by standard USB
port
Powered from standard
USB port or 12VDC-IN
power jack
Dimensions 124 mm (H) x 188 mm (W)
x 80 mm (D)
195 mm (H) x 245 mm (W)
x 79 mm (D)
Environmental Operation temperature: 0ºC ~ +50ºC
Operating humidity: 20% to 85%, non-condensing
Storage temperature: -10ºC ~ +70ºC
Storage humidity: 5% to 90%, non-condensing