POSIFLEX LM-2310 User manual

Part 1
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the Touch Monitor LM-2310/LM-2210. This product provides exquisite touch control
capability over a stable and adjustable LCD monitor with minimal footprint.
The manufacturer of the LM-2310/LM-2210 monitor heartily apologizes to the user for reserving the right to change or to modify
this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may
always obtain the most up to date information through any of our web sites: http://www.posiflex.com, http://www.posiflex.com.tw,
http://www.posiflexusa.com.
Copyright Posiflex Technology, Inc. 2012
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
I. FEATURES
•LM-2310/LM-2210 is principally designed for Posiflex KS-series POS
solutions
•10” LCD monitor with tilt adjustment for industrial and commercial use
•High quality TFT LCD panel.
•Easy maintenance structure allowing easy cleaning
•Super VGA monitor resolution up to 800 x 600 pixels
•Support power supply through LCD cable from Posiflex Terminal to
operate without power adaptor
LM-2310/2210
LCD Monitor
User’s Manual
Rev. Original
P/N:
1
9610900010

Part 2
II. PARTS IDENTIFICATION
A. FRONT VIEW (LM-2210/LM-2310)
B. REAR VIEW (LM-2210/LM-2310)
C. SIDE VIEW (LM-2310)
Display Screen
Power LED
Main Unit
Stand
VGA Connector and
DC jack
Control button area
OSD button
NXT button
“+” button
“-“ button
Power switch
Hinge
Main Unit
Base Stand
Cable Exit
Joint Bracket

Part 3
Control button area
VGA Connector and
DC jack.
NXT button
“+” button
OSD button
“-“ button
Power switch
C. SIDE VIEW (LM-2210)
D. POWEPOWER LED INDICATION
•Green: standby (no signal)
•Blue: operating
Before routing the cable, please release the hooks
Of stand’s back cover as arrowed in the right
picture . For cable routing in mini slim base,
please refer to the picture
at left. There are 2 cable
tie holder slits on the
metal bracket for the
trunk as arrowed in the picture. Hold all the external
cables with a cable tie through the right cable tie holder
slit and leave the cables to the left holder slit. Have all
cables to pass through the oval hole on the trunk to come out of the front side
of trunk. Connect all the cable ends to main unit. Be sure not to damage any
cable during this operation.
CABLE ROUTING IN BASE (LM-2210)

Part 4
VESA MOUNT
After releasing the stand’s back cover, please unfasten these
two screws to remove the main structure of base stand
which arrowed in the right picture.
After that, please use flat drill to release the hinge cover
from the arrowed side as show in the right picture.
Next, unfasten these four screws which fix the hinge as
shown in the middle right picture and remove the hinge.
Now, there are four screws holes which fit in with VESA
standard 75mm and use another four bind head screws
which attached in the packing kit to fasten on the VESA
arm or bracket.
CABLE ROUTING IN BASE (LM-2310)
Before routing the cable, please release the hooks of back cover of stand as
arrowed in the right picture.
For cable routing in mini slim base, please
refer to the picture below. There are 3 cable
tie holder slits on the metal bracket for the trunk
as arrowed in the picture.
Hold all the external cables with a cable
tie through the right cable tie holder slit and
leave the cables to the left holder slit. Have
all cables pass through the oval hole on the
trunk to come out of the front side of trunk.
Connect all the cable ends to main unit. Be sure not to damage any cable
during this operation.

Part 5
Assembling and Disassembling(LM-2310)
After releasing the back cover of stand, please unfasten these 4 screws to
remove the main structure of base stand shown in the rightmost picture.
Next, unfasten these 3 screws which fix the hinge as
shown in the right picture.
Now, there are 3 screws holes which fit in with VESA
standard 75mm
After that, please use flat drill to release 3 screws shown
in the right picture.
OSD
The monitor can be turned OFF only when there is video signal; turned ON
only when there is video signal and after the “Turn Off Panel” message
vanishes. The default status is set to ON when power is supplied unless
manually turned OFF. Since this button controls only the display power but not
the display controller, please try to disconnect the power cable or the VGA
cable once unfortunately the screen display goes into a power-off mode.
OSD functions
Press “OSD” button with a normal display on the screen to activate the OSD
functions (On Screen Display adjustment). The OSD window will pop up on
the screen. On top part of this window is a Posiflex logo with the OSD
firmware version indicated to its lower right part. Below this area are a row of
icons for main OSD menu. Below the main menu are a group of icons for
submenu that corresponds to one icon selected in the main menu. An analysis
of the video signal on resolution and refresh rate will be displayed at the
bottom. Applicable icons in the main menu and its subsequent menus are
illustrated below.
“MAIN MENU”: There are a total of 5 icons in this menu:
One of the 5 icons will be displayed in inverted color to indicate its
relationship with the submenu below. Pressing “NXT” button will shift the

Part 6
selected icon one by one from left to right and then wrap around to the leftmost
part. Press “OSD” button to enter the selected sub menu. If there is no button
for OSD setting, is pressed within a period of time (about 5 seconds to 1
minute as programmed) the OSD window will disappear with all the adjusted
parameters saved. Items in sub menu are illustrated below.
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3
icons in this submenu: Press “OSD” button to select item or
return to main menu. Press “NXT” button to select among brightness, contrast
and exit.
“BRIGHTNESS ADJUST”: When this item is selected, there
will be only the brightness icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase brightness. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
“CONTRAST ADJUST”: When this item is selected, there will
be only the contrast icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+”
button to increase contrast. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
“EXIT”: Return to “Main menu”.
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:
Press “OSD” button to select item or return to main menu. Press
“NXT” button to select among auto color adjust, auto RGB reset, Color
balance adjust and exit.
“AUTO COLOR ADJUST”: Upon an “OSD” button press on
this icon the monitor will perform an automatic color adjustment and
exits the OSD window leaving 2 icons below at center of the screen.
Press “NXT” button to switch the selection. Press “OSD” button to
make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“AUTO RGB RESET”: Upon an “OSD” button press on this
icon the monitor will perform an automatic RGB reset and exits the
OSD window leaving 2 icons below at the center of the screen. Press
“NXT” button to switch the selection. Press “OSD” button to make the
choice.
“ACCEPT”: Accept the reset result.
“REJECT”: Decline the reset and return to previous
setting.
“COLOR BALANCE ADJUST”: When this item is selected,
there will be 7 icons in this item between

Part 7
main menu area and the video signal mode. Press “OSD” button to
select an item or return to color adjust submenu. Press “NXT” button to
select among separate color adjustment, 4200K, 5000K, 6500K, 7500K,
9300K and exit.
“SEPARATE COLOR ADJUST”: When this item is
selected, there will be 3 adjustment indication bars between the
main menu area and the video signal mode. Press “NXT” button
to select among the 3 colors Red, Green and Blue respectively.
Press “+” button to intensify that color. Press “-” to reduce.
Press “OSD” button to save the current setting and return to
“Color balance adjust submenu”.
“4200K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 4200 degrees Kelvin.
“5000K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 5000 degrees Kelvin.
“6500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 6500 degrees Kelvin.
“7500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 7500 degrees Kelvin.
“9300K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 9300 degrees Kelvin.
“EXIT”: Return to “Color adjust submenu”.
“EXIT”: Return to “Main menu”.
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this
submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among auto geometry adjustment,
horizontal size, phase, horizontal position, vertical position and exit.
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press
on this icon the monitor will perform an automatic geometry adjustment
and exits the OSD window leaving 2 icons below at the center of the
screen. Press “NXT” button to switch the selection. Press “OSD” button
to make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“HORIZONTAL SIZE”: When this item is selected, there will
be only the horizontal size icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase horizontal size. Press “-” to decrease. Press “OSD”
button to save the current setting and return to “Geometry adjust
submenu”.
“PHASE”: When this item is selected, there will be only the

Part 8
phase adjustment icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” or “-
” button to adjust the pixel synchronization phase for the best picture
display. Press “OSD” button to save the current setting and return to
“Geometry adjust submenu”.
“HORIZONTAL POSITION”: When this item is selected, there
will be only the horizontal position icon with an adjustment indication
bar under it between the main menu area and the video signal mode.
Press “+” or “-” button to shift the screen display to the right or left.
Press “OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“VERTICAL POSITION”: When this item is selected, there
will be only the vertical position icon with an adjustment indication bar
under it between the main menu area and the video signal mode. Press
“+” button to shift up the screen display. Press “-” to shift down. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“EXIT”: Return to “Main menu”.
“TOOLS SUBMENU”: When this item is selected, there are 5 icons in
this submenu: Press “OSD” button to select item or return
to main menu. Press “NXT” button to select among OSD submenu, reset to
default, phase, smoothness / sharpness adjust, mode select and exit.
“OSD SUBMENU”: When this item is selected, there are 4 icons
in this submenu: Press “OSD” button to select item or
return to main menu. Press “NXT” button to select among OSD time,
OSD horizontal position, OSD vertical position and exit.
“OSD TIME”: When this item is selected, there will be
only the OSD time icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press
“+” or “-” button to adjust the waiting time for OSD operation
before OSD termination between 5 to 60 seconds. Default value
is 30 seconds. Press “OSD” button to save the current setting
and return to “OSD submenu”.
“OSD HORIZONTAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to shift OSD
window right. Press “-” to shift left. Press “OSD” button to save
the current setting and return to “OSD submenu”.
“OSD VERTICAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area

Part 9
and the video signal mode. Press “+” button to move OSD
window downward. Press “-” to go upward. Press “OSD” button
to save the current setting and return to “OSD submenu”.
“EXIT”: Return to “Tools submenu”.
“RESET TO DEFAULT”: Pressing “OSD” button on this icon
will set all parameters back to the status when the monitor is factory
installed.
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is
selected, there will be only the smoothness / sharpness adjustment icon
with an adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to increase smoothness of
display (decrease sharpness). Press “-” to go the other way. Press
“OSD” button to save the current setting and return to “OSD submenu”.
“MODE SELECT”: Pressing “OSD” button on this icon will
have no effect at all if the display mode is not one of the confusing
modes. The confusing modes here mean 640 x 400 or 720 x 400 in
display resolution as both modes have refresh rate of 70Hz, horizontal
frequency of 37.9KHz and pixel frequency of 31.5MHz making it
impossible for automatic select. These modes are not used in normal
Windows display.
“EXIT”: Return to “Main menu”.
“EXIT”: Exit OSD setup with all adjustment saved.
SUPPORTED DISPLAY MODES
For video signals beyond the supported display modes, there will be a message
“Out Of Range” on the middle of screen. Maximum supported color depth is
24 bits or 16.7M colors. Supported display modes are illustrated in the table:
Display Resolution Refresh Rate (Hz)
Horizontal
Frequency (KHz)
640*400 70 37.9
60 31.5
72 37.9
640*480
75 37.5
720*400 70 37.9
56 35.1
60 37.9
72 48.1
800*600
75 46.9
警告
警告警告
警告
本電池如果更換不正確會有爆炸的危險
請依製造商說明書處理用過之電池
T31454
警告使用者
警告使用者警告使用者
警告使用者
這 甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況下，使用者會被要
求採取某些適當的對策。