POSIFLEX LM6112 User manual

P/N: 19050900020 1
LM6100 Series
LCD Monitor
USER’S MANUAL
Rev. : A
I. FEATURES
•Light weight and high luminance LCD monitor for industrial and commercial use
•Application covers POS, POIS (Kiosk), Factory Automation etc.
•High quality 12.1” TFT LCD panel with scaling up function for full screen display
•Successor from earlier LM6000 series and supports display resolution up to 1024 x
768pixels
•Tilt and swivel adjustable construction
•Spill proof and easy maintenance structure allowing easy cleaning
FCCNOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the LCD Monitor LM6100 series. These series provide versatile font
formats and support various instruction sets. These series of products receive instructions in serial communication
protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial
device if properly configured.
The manufacturer of the LM6100 series heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw,
http: //www.posiflexuk.com, http://www.posiflexusa.com.
Copyright Mustek Corp. 2002, 2003
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service marks of their respective
owners.

2
II. MODEL NUMBERS
LM6112: 12.1” LCD Monitor w/ stand
LM6101: 12.1” LCD Monitor w/ joining mechanism for Posiflex touch
terminals such as TP-7000 series
III. CARTON CONTENTS
1. LCD Monitor panel unit
2. Monitor stand (for LM6112) or joining mechanism (for LM6101)
3. Pivot screw (1x) and pan head fixing screws (2x for LM6101)
4. User’sManual
5. VGA cable: 20867244100 (for LM6112) or 20863241710 (for
LM6101)
6. Power adaptor: ASP0P042WTB001 & power cord (for LM6112)
IV. INSTALLATION
1. Match the bottom of the panel unit into the monitor stand (for LM6112) or
joining mechanism (for LM6101).
2. Screw on the pivot screw for LM6112. Screw on the pivot screw through a
split washer and then through a plain washer for LM6101.
3. Fix LM6101 to the Posiflex TP7000 terminal per instruction of the terminal.
4. For LM6112, connect the end of VGA cable with the power connector to the
LM6112
LM6101
on back of
TP7000
Pivot Screw
LM6112 LM6101

3
back of the panel unit. For LM6101, please arrange the power to be supplied
through the interface cable from the main unit and just connect the video
interface cable. Connect the other end of VGA cable to the appropriate VGA
port. The monitor will always turn ON whenever power is made available.
5. Adjust for best viewing tilt angle and engage the on screen display (OSD)
adjustment for best display effect whenever necessary. The monitor will sign
for “No Signal” status and go into power saving mode in 5 seconds when
there is no video signal. The display will come back when the signal does.
V. OSD
A. OSD buttons
“OSD” button: To enter OSD setup menu, or to perform function selected
in OSD operation.
“NXT” button: To go to next option function.
“” “” button: To increase setting.
“”“” button: To decrease setting.
“” “” button: To turn the monitor power ON/OFF. The monitor can be
turned OFF only when there is video signal and can be turned ON only
when there is video signal and after the “Turn Off Panel” message
VGA Connector
Power Connector in VGA Cable
Power Connector from Power Adaptor
for LM6112

4
vanishes. The default status is set to ON when power is supplied unless
manually turned OFF. Since this button controls only the display power
but not the display controller, please try disconnect the power cable or
the VGA cable once unfortunately the screen display goes into a mess.
B. OSD functions
Press “OSD” button with a normal display on the screen to activate the
OSD functions (On Screen Display adjustment). The OSD window will pop up
on the screen. On top part of this window is a Posiflex logo with the OSD
firmware version indicated to its lower right. Below this area is a row of icons
for main OSD menu. Below the main menu is a group of icons for submenu that
corresponds to one icon selected in the main menu. An analysis of the video
signal on resolution and refresh rate will be displayed at the bottom. Applicable
icons in the main menu and its subsequent menus are explained below.
“MAIN MENU”: There are in total 5 icons in this menu: One of the 5
icons will be displayed in inverted color to indicate its
relationship with the submenu below. Pressing “NXT” button will shift the
selected icon one by one from left to right and then wrap around to the most left.
Press “OSD” button to enter the selected sub menu. If there is no button for OSD
setting is pressed within a period of time (about 5 seconds to 1 minute as
programmed) the OSD window will disappear with all the adjusted parameters
saved. Explanations on items in sub menu are as below.
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3
icons in this submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among brightness, contrast and exit.
“BRIGHTNESS ADJUST”: When this item is selected, there will
be only the brightness icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to increase brightness. Press “-” to decrease. Press “OSD” button to save
the current setting and return to “Brightness/Contrast submenu”.
“CONTRAST ADJUST”: When this item is selected, there will be
only the contrast icon with an adjustment indication bar under it between
the main menu area and the video signal mode. Press “+” button to
increase contrast. Press “-” to decrease. Press “OSD” button to save the
current setting and return to “Brightness/Contrast submenu”.

5
“EXIT”: Return to “Main menu”.
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:
Press “OSD” button to select item or return to main menu. Press
“NXT” button to select among auto color adjust, auto RGB reset, Color balance
adjust and exit.
“AUTO COLOR ADJUST”: Upon an “OSD” button press on this
icon the monitor will perform an automatic color adjustment and exits the
OSD window leaving 2 icons below at center of the screen. Press “NXT”
button to switch the selection. Press “OSD” button to make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“AUTO RGB RESET”: Upon an “OSD” button press on this icon
the monitor will perform an automatic RGB reset and exits the OSD
window leaving 2 icons below at center of the screen. Press “NXT” button
to switch the selection. Press “OSD” button to make the choice.
“ACCEPT”: Accept the reset result.
“REJECT”: Decline the reset and return to previous setting.
“COLOR BALANCE ADJUST”: When this item is selected, there
will be 7 icons in this item: between main menu
area and the video signal mode. Press “OSD” button to select an item or
return to color adjust submenu. Press “NXT” button to select among
separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K and exit.
“SEPARATE COLOR ADJUST”: When this item is
selected, there will be 3 adjustment indication bars between the main
menu area and the video signal mode. Press “NXT” button to select
among the 3 colors Red, Green and Blue respectively. Press “+”
button to intensify that color. Press “-” to reduce. Press “OSD”
button to save the current setting and return to “Color balance adjust
submenu”.
“4200K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 4200 degrees Kelvin.
“5000K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 5000 degrees Kelvin.

6
“6500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 6500 degrees Kelvin.
“7500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 7500 degrees Kelvin.
“9300K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 9300 degrees Kelvin.
“EXIT”: Return to “Color adjust submenu”.
“EXIT”: Return to “Main menu”.
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this
submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among auto geometry adjust,
horizontal size, phase, horizontal position, vertical position and exit.
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press on
this icon the monitor will perform an automatic geometry adjustment and
exits the OSD window leaving 2 icons below at center of the screen. Press
“NXT” button to switch the selection. Press “OSD” button to make the
choice. “ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“HORIZONTAL SIZE”: When this item is selected, there will be
only the horizontal size icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to increase horizontal size. Press “-” to decrease. Press “OSD” button to
save the current setting and return to “Geometry adjust submenu”.
“PHASE”: When this item is selected, there will be only the phase
adjust icon with an adjustment indication bar under it between the main
menu area and the video signal mode. Press “+” or “-” button to adjust the
pixel synchronization phase for best picture display. Press “OSD” button
to save the current setting and return to “Geometry adjust submenu”.
“HORIZONTAL POSITION”: When this item is selected, there
will be only the horizontal position icon with an adjustment indication bar
under it between the main menu area and the video signal mode. Press “+”
or “-” button to shift the screen display to right or left. Press “OSD” button
to save the current setting and return to “Geometry adjust submenu”.

7
“VERTICAL POSITION”: When this item is selected, there will
be only the vertical position icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to shift up the screen display. Press “-” to shift down. Press “OSD” button
to save the current settingand return to “Geometry adjust submenu”.
“EXIT”: Return to “Main menu”.
“TOOLS SUBMENU”: When this item is selected, there are 5 icons in
this submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among OSD submenu, reset to default,
phase, smoothness / sharpness adjust, mode select and exit.
“OSD SUBMENU”: When this item is selected, there are 4 icons in
this submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among OSD time, OSD
horizontal position, OSD vertical position and exit.
“OSD TIME”: When this item is selected, there will be only
the OSD time icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” or
“-” button to adjust the waiting time for OSD operation before OSD
termination between 5 to 60 seconds. Default is 30 seconds. Press
“OSD” button to save the current setting and return to “OSD
submenu”.
“OSD HORIZONTAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area and
the video signal mode. Press “+” button to shift OSD window right.
Press “-” to shift left. Press “OSD” button to save the current setting
and return to “OSD submenu”.
“OSD VERTICAL POSITION”: When this item is selected,
there will be only the vertical position icon with an adjustment
indication bar under it between the main menu area and the video
signal mode. Press “+” button to move OSD window downward.
Press “-” to go upward. Press “OSD” button to save the current
setting and return to “OSD submenu”.
“EXIT”: Return to “Tools submenu”.

8
“RESET TO DEFAULT”: Pressing “OSD” button on this icon will
set all parameters back to the status when the monitor left factory.
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is
selected, there will be only the smoothness / sharpness adjust icon with an
adjustment indication bar under it between the main menu area and the
video signal mode. Press “+” button to increase smoothness of display
(decrease sharpness). Press “-” to go the other way. Press “OSD” button to
save the current setting and return to “OSD submenu”.
“MODE SELECT”: Pressing “OSD” button on this icon will have
no effect at all if the display mode is not one of the confusing modes. The
confusing modes here mean 640 x 400 or 720 x 400 in display resolution
as both mode have refresh rate of 70Hz, horizontal frequency of 37.9KHz
and pixel frequency of 31.5MHz making it impossible for automatic select.
These modes are not used in normal Windows display.
“EXIT”: Return to “Main menu”.
“EXIT”: Exit OSD setup with all adjustment saved.
VI. SUPPORTED DISPLAY MODES
For video signals beyond the supported display modes, there will be a
message “Out Of Range” on middle of screen. Maximum supported color depth
is 18 bits or 262,144 colors. Supported display modes are as in the table:
Display Resolution Refresh Rate (Hz) Horizontal Frequency (KHz)
640*400 70 37.9
60 31.5
72 37.9640*480 75 37.5
720*400 70 37.9
56 35.1
60 37.9
72 48.1
800*600
75 46.9
60 48.4
70 56.5
1024*768 75 60