POSIFLEX TM-30 Series User manual

Package Contents
9.7” LM/TM-3X10E or 14” LM/TM-3X14E or
15” LM/TM-3X15E
POS Monitor……………...……….(x 1)
VGA Cable………………………..(x 1)
USB type A to B cable…………....(x 1)
(For TM-30XXE/32XXE Only)
Mounting kits …...……………..…(x 1)
User Manual………………………(x 1)
Specifications
LM-30XXE/32XXE Models
LM-3010E
LM-3014E
LM-3015E
LM-3210E
LM-3215E
Display
LCD Panel
9.7" TFT
LCD
14" TFT
LCD
15.0" TFT
LCD
9.7" TFT
LCD
15.0" TFT
LCD
Resolution
(H) x (V)
1024 x 768
1366 x 768
1024 x 768
Touch
Touch type
N/A
Interface
N/A
General Specification
Display
Interface
VGA
Power
Supply
12V from Posiflex terminal VGA port
TM-30XXE/32XXE Models
TM-3010E
TM-3014E
TM-3015E
TM-3215E
Display
LCD Panel
9.7" TFT LCD
14" TFT LCD
15.0" TFT LCD
Resolution
(H) x (V)
1024 x 768
1366 x 768
1024 x 768
Touch
Touch type
Bezel-free P-CAP touch panel
Resistive touch
panel
Interface
USB
General Specification
Display
Interface
VGA
Power
Supply
12V from Posiflex terminal VGA port
19610903010 Ver. Original
http://www.posiflex.com
LM/TM-30XXE/32XXE Monitor
User Manual
1

Views of LM/TM-3X10E
Front View
Rear View
I/O Ports of LM-3X10E
I/O Ports of TM-3010E
9.7” LM-3210E LCD Panel
VGA Port
DC-IN Power Jack
Power LED Indicator
9.7” LM-3010E LCD Panel
9.7” TM-3010E P-Cap Touch Panel
VGA Port
USB (Type B) Port
DC-IN Power Jack
Power LED Indicator
Mounting Bracket
for HS series Terminals
Mounting Bracket
for KS series Terminals
Mounting Bracket
for XT series Terminals
OSD button
EXT button
＋button
－button/ Power button
OSD Control Button
2

Views of the LM/TM-3014E
Front View
Rear View
I/O Ports
Side Mount Cover
14” LM-3014E LCD Panel
14” TM-3014E P-Cap Touch Panel
VGA Port
USB (Type B) Port
DC-IN Power Jack
USB Port
Power LED Indicator
Mounting Bracket
for KS series Terminals
Mounting Bracket
for XT series Terminals
OSD button
EXT button
＋button
－button/ Power button
OSD Control Button
3

Views of the LM/TM-3015E/3215E
Front View
Rear View
I/O Ports
15” LM-3215E LCD Panel
15” TM-3215E Resistive Touch Panel
15” LM-3015E LCD Panel
15” TM-3015E P-Cap Touch Panel
VGA Port
USB (Type B) Port
DC-IN Power Jack
LED Indicator
LED Indicator
USB Port
Side Mount Cover
Mounting Bracket
for KS series Terminals
Mounting Bracket for
XT series Terminals
OSD button
EXT button
＋button
－button/ Power button
OSD Control Button
4

Installing LM/TM-30XXE/32XXE
According to the model type of your monitor and terminal, the relevant
instructions are provided below to help you mount your monitors onto your
Posiflex terminals. During installation, please ensure the terminal is properly
turned off and disconnected from the power sources to avoid potential hazards.
Mounting to HS series Terminals
1. Lay your POS terminal on a flat surface with
its rear facing towards you.
2. Press down the release tab of top I/O interface
cover.
3. Pull the top I/O cover in the direction shown
by the arrow in the figure to remove the cover.
4. Position the monitor on a flat surface. While
keeping it steady with one hands, pull the rear
mounting bracket upright as shown in the
figure.
5. Support your monitor to align its mounting
bracket with four screw holes at the back of
your terminal. Secure the mounting bracket
with four #6-32-10L fixing screws.
5

6. Connect the monitor to the terminal using VGA cable.
6.1 Connect one end of the VGA cable to
the VGA port at the bottom I/O plate
of your monitor.
6.2 Take the other end of VGA cable to
insert it into the VGA port of your
terminal.
7. For TM series users, connect the monitor to the terminal using USB
type A to B cable to enable touch function for your monitor. If the
monitor you are using isn’t TM series, please skip this step.
7.1 Grab Type-B connector of USB
cable, and then insert it into Type-B
USB port of your monitor
7.2 Properly attach Type-A connector of
USB cable to your POS terminal.
8. Break the release tab of the top I/O interface
cover for HS series terminal.
9. After tucking the extra cable into the I/O
compartment and thread the cable through the
cable exit, push the back cover into place.
10. After ensuring the monitor is well installed, tilt
your monitor up or down to your desired angle.
While setting up the tilting adjustment, be
careful not to press on the LCD panel.
Cable Exit
6

Mounting to KS Terminals
1. Position your terminal with its rear facing
towards you.
2. Take L type mounting bracket out of the
package. Align the four screw holes of the
mounting bracket with the hole pattern at the
back of the terminal.
3. Insert four #6-32-12L fixing screws into the
screw holes and then tighten the screws to
secure the mounting bracket.
4. Lay the monitor on a flat surface with the
screen facing downward and its I/O ports
facing toward you. While holding the monitor
steady with one hand, pull the monitor bracket
upright.
5. Lift the monitor to align three screw holes on
the monitor bracket with those on the bracket
attached to the terminal using the alignment
dots.
6. Properly attach two brackets with three #6-32-
6L fixing screws. Make sure the monitor is
well mounted onto your terminal.
Alignment Dot
7

7. Pull outward the locking levers and then
remove the neck cover in the direction shown
by the arrow.
8. Connect VGA cable to the terminal.
9. For TM series users, attach Type-A connector
of USB cable to your POS terminal.If the
monitor you are using isn’t TM series,
please skip this step.
10. Pass the cables through the cable exit, route them along the cable
passage, and fasten the cables with cable tie as shown in the picture.
11. Push back the neck cover into place.
12. Make sure the cables can be pulled out of the
cable exit from the base.
13. Connect VGA cable to your monitor.
Cable exit
Cable exit
Cable tie
8

14. For TM series users, grab Type-B connector of
USB cable, and then insert it into Type-B USB
port of your monitor to enable touch function.
If the monitor you are using isn’t TM series,
please skip this step.
15. The installation is completed. While tilting the
screen up or down in the direction shown by
the arrow, do not press on the LCD panel.
Mounting to XT Terminals with Gen 7E/8E Base
1. Position your terminal with its rear facing
toward you. At the edges of the base stand
bracket are located two shorter horizontal rails
(2) (3) and two longer vertical rails (1) (4),
which are used to hold your cable into place.
2. Release the rail from the base.
To run the cable through the cable passage on the left, according to
the sequence number, first remove the longer rail and then the shorter
one from the base stand by sliding them in the direction shown by the
arrow.
Or, if you prefer to thread the cable through the cable passage on the
right side, first remove the longer rail and then shorter one from the
base stand according to the sequence number.
4
3
2
1
1
2
1
2
9

3. After positioning your terminal with its screen
facing downwards, lift the monitor and then
align the four fixing screw holes on its
mounting bracket with the hole pattern at the
rear of the terminal as shown in the figure.
4. Insert four #6-32-10L screws into the screws
holes and then tighten them to secure the
mounting bracket.
5. Take the VGA cable out of the package, and
then connect it to your monitor.
6. For TM series users, plug Type-B connector of
USB cable into Type-B USB port of your
monitor to enable touch function. If the
monitor you are using isn’t TM series,
please skip this step.
7. While pushing the VGA cable into cable passages on the left side, also
reserve the enough cable for tilting the monitor.
8. For TM series users, tuck USB cable through the cable passage on the
right side. Reserve the enough cable needed for tilting the monitor.
Please skip this step if USB cable is not available.
Cable Exit
Cable Exit
10