Posiflex Cd-3200 Setup guide

CD-3200

2D Image Scanner

Advanced Manual

Version: A0

Contents

INTRODUCTION ....................................................................................................- 1 -

1. GENERAL OPTIONS..........................................................................................- 5 -

1.1. Restore to Factory Default Settings ...............................................................- 5 -

1.2. Switch User Interface and Reset to Default Settings .....................................- 6 -

1.3. Check Firmware Version ...............................................................................- 6 -

1.4. Enhance Barcode Scanning on Screens .........................................................- 6 -

1.4.1 No illumination detection.........................................................................- 7 -

1.4.2 Prevention of flicker.................................................................................- 7 -

1.4.3 Prevention of specular reflection..............................................................- 7 -

1.5. Configure Data Transmission Interval...........................................................- 8 -

2. INTERFACE.........................................................................................................- 9 -

2.1. RS232 options................................................................................................- 9 -

2.1.1. Baud rate settings...................................................................................- 10 -

2.1.2. Data, parity and stop bits.......................................................................- 11 -

2.1.3. Handshaking..........................................................................................- 12 -

2.1.4. Intercharacter delay for RS232..............................................................- 15 -

2.2. Keyboard wedge/USB options.....................................................................- 15 -

2.2.1. Keyboard language................................................................................- 16 -

2.2.2. Special options.......................................................................................- 17 -

2.2.3. Intercharacter delay for wedges/USB....................................................- 19 -

3. CODE OPTIONS................................................................................................- 20 -

3.1. Setting of readable codes..............................................................................- 21 -

3.1.1. Enabling a single read. code..................................................................- 21 -

3.1.2. Enabling of readable codes....................................................................- 25 -

3.2. Setting of number of characters ...................................................................- 28 -

3.3. Setting code specific options........................................................................- 33 -

3.3.1. Options for UPC-A................................................................................- 34 -

3.3.2. Options for UPC-E ................................................................................- 35 -

3.3.3. Options for EAN-13 and EAN-8...........................................................- 37 -

3.3.4. Options for Code 39 and It. Pharm........................................................- 40 -

3.3.5. Options for Codabar ..............................................................................- 43 -

3.3.6. Options for 2of5 and S-Code.................................................................- 46 -

3.3.7. Options for IATA ..................................................................................- 49 -

3.3.8. Options for MSI/Plessey........................................................................- 49 -

3.3.9. Options for Telepen...............................................................................- 51 -

3.3.10. Options for UK/Plessey.......................................................................- 52 -

3.3.11. Options for Code 128 and GS1-128....................................................- 53 -

3.3.12. Options for Code 93 ............................................................................- 54 -

3.3.13. Options for Code 11 ............................................................................- 56 -

3.3.14. Options for Korean Postal Authority code ..........................................- 57 -

3.3.15. Options for Intelligent Mail Barcode...................................................- 58 -

3.3.16. Options for POSTNET ........................................................................- 59 -

3.3.18. Options for Composite Codes..............................................................- 61 -

3.3.19. Options for Codablock F .....................................................................- 63 -

3.3.20. Options for DataMatrix .......................................................................- 63 -

3.3.21. Options for Aztec.................................................................................- 65 -

3.3.22. Options for Chinese Sensible code......................................................- 66 -

3.3.23. Options for QR Code...........................................................................- 67 -

3.3.24. Options for Micro QR Code................................................................- 68 -

3.3.25. Options for Maxicode..........................................................................- 69 -

3.3.26. Options for PDF417.............................................................................- 70 -

3.3.27. Options for MicroPDF417...................................................................- 71 -

4. STRING OPTIONS............................................................................................- 73 -

4.1. Case conversion............................................................................................- 73 -

4.2. Set prefix and suffix.....................................................................................- 74 -

4.2.1. Set prefix................................................................................................- 82 -

4.2.2. Set suffix................................................................................................- 85 -

4.3.1. Direct input keyboard keys....................................................................- 88 -

4.3.3. Direct input numeric..............................................................................- 94 -

4.3.4. Direct input character ............................................................................- 95 -

4.3.5. Direct input lower case character ..........................................................- 97 -

4.3.6. Direct input control character................................................................- 99 -

4.3.7. Direct input code id/length ..................................................................- 101 -

5. READ OPTIONS..............................................................................................- 102 -

5.1. Read mode options.....................................................................................- 102 -

5.1.1. Multiple read reset time.......................................................................- 105 -

5.1.2. Quiet zone options...............................................................................- 106 -

5.1.3. Auto trigger options.............................................................................- 106 -

5.1.4. Detection Mode ...................................................................................- 107 -

5.1.5. Auto Trigger Condition.......................................................................- 108 -

5.2. Read time options.......................................................................................- 108 -

5.3. Redundancy................................................................................................- 109 -

5.4. Positive and negative bar codes .................................................................- 109 -

5.5. Floodlight and aiming options ...................................................................- 110 -

5.6. Prevention of flicker...................................................................................- 111 -

5.7. LED aiming................................................................................................- 112 -

6. INDICATOR OPTIONS...................................................................................- 113 -

6.1. Buzzer settings ...........................................................................................- 113 -

6.2. Good read LED ..........................................................................................- 115 -

7. MISCELLANEOUS.........................................................................................- 116 -

7.1. Diagnostics.................................................................................................- 116 -

7.2. Serial configuration support.......................................................................- 117 -

APPENDIX A. TROUBLE SHOOTING.............................................................- 120 -

iii

APPENDIX B. GLOSSARY OF TERMS............................................................- 121 -

INTRODUCTION

This menu book is intended for setting up your bar code reader to optimize its

performance for your particular application. When the required options have been

configured, they remain in the reader, even after power down. The reader can be

returned to factory default by reading the default label.

Menu labels

The reader must be set by reading the bar code labels in the menu table. The layout of

the table is explained in next figure 0.01. To have the bar codes properly decoded,

keep in mind that you are required to pull a trigger to initiate the decoding

process after accurately aiming the scanner at the 1D setup labels.

- 1 -

Besides options, some chapters have commands. The commands need to be scanned

directly, without reading the “SET” and “END” labels. The commands are executed

directly and, unlike options, are not stored in non-volatile memory.

Configuring via the menu book

To configure the required options proceed as follows:

zscan the SET label

zscan the required option(s)

zscan the END label

After scanning the END label, the new settings are stored in non-volatile memory.

Recommended steps to follow for quick configuration

After checking your connection you are ready to start the configuration of your

reader.

zCheck connection:

Ensure that the power is disconnected from your equipment before you connect the

reader. After connecting the data cable, the power can be applied to the equipment

and the reader.

z1:

Use chapter 1 to set the correct default for your reader.

* The reader is now in factory default.

z2:

Use chapter 2 to optimize the interface.

* The reader is now able to read bar codes and transmit the data.

z3:

Use chapter 3 to optimize the reader for the type of bar codes you use. Set the

readable codes first and then the options for each of these codes.

* The reader is now able to read the codes you selected, validate the data using length

and check digit and transmit that part of the data you specified.

z4:

Use chapter 4 to select the string options for your application. These include

transmission of code length, conversion of upper and lower case and setting a prefix

and suffix.

* The reader can now read and transmit the data in the required format.

z5:

Use chapter 5 to select the read options to your preference. These options affect the

read mode, read time, trigger and redundancy.

- 2 -

z6:

Use chapter 6 to select the indicator options you prefer. These options affect the

operation of the buzzer and good read LED.

* The reader will now operate to your personal preference.

See figure 0.02.

Configuring via RS232

In the middle column of the menu pages the command is printed, e.g. U2. These

commands can be sent to readers with an RS232 interface. To configure via the

RS232 port proceed as follows:

ztransmit <ESC><Command string 1><CR>

ztransmit <ESC><Command string 2><CR>

ztransmit <ESC><Command string n><CR>

ztransmit <ESC>Z2<CR>

<ESC>

<ESC> is the ASCII escape character (Hex 1B).

<Command string> is the ASCII command with its parameters as would be scanned

from the menu book, i.e. <ESC>M41B<CR> configures the ASCII control code

<STX> as the prefix for Code 39.

Example in hexadecimal format:

1B 4D 34 31 4B ØD

- 3 -

Each 3-character command should be preceded with the '[' character (Hex 5B) i.e.

<Esc>[BCC<CR> is used to enable Data Matrix.

Each 4-character command should be preceded with the ']' character (Hex 5D) i.e.

<Esc>]DIAU<CR> is used to disable auto connect.

<CR>

<CR> is the ASCII CR character (Hex ØD).

Some options are not immediately active, like baud rate settings. Most other options

are immediately active, but the command Z2 must be send to store the settings to

non-volatile memory.

The following commands may be used to:

Command B sound a good read beep

Command E sound an error beep

Command G motor off

Command H motor on

Command L switch on good read LED

Command N switch on bad read LED

Command O switch on both LEDs

Command Y de-trigger the reader

Command Z trigger the reader

The characters transmitted must be separated by an intercharacter delay to allow the

reader to process each character received and to execute the command string.

Package Content

CD-3200U

zCD-3200U 2D Image Scanner

zST-8000 scanner holder stand

(Optional)

zUSB cable

zQuick setup guide for CD-3200U/R

CD-3200R

zCD-3200R 2D Image Scanner

zST-8000 scanner holder stand

(Optional)

zRS-232 cable

zQuick setup guide for CD-3200U/R

- 4 -

1. GENERAL OPTIONS

1.1. Restore to Factory Default Settings

This option allows you to undo all previously configured options and bring the

reader's configuration back to factory default settings. These factory default settings

are printed in bold.

Note that differences may occur depending on the type of interface as will be

mentioned in the text.

Select only the correct default settings corresponding to your hardware "defaults"

label.

The interfaces supported depend on the reader model and software release. Please

consult your sales office for not listed interfaces.

RS232

USB-HID

USB-VCP

- 5 -

Table of contents

Other POSIFLEX Scanner manuals

POSIFLEX

POSIFLEX CD-3600 Setup guide

POSIFLEX

POSIFLEX PG-200/2D-O Setup guide

POSIFLEX

POSIFLEX CD-3600U User manual

POSIFLEX

POSIFLEX SA Series User manual

POSIFLEX

POSIFLEX KB-4000 User manual

POSIFLEX

POSIFLEX CD-3203U User manual

Popular Scanner manuals by other brands

Radio Shack

Radio Shack PRO-433 quick start guide

Atid

Atid AT911N series user guide

Siemens

Siemens RUGGEDCOM WiN5100 Faq

Canon

Canon CanoScan LiDE 20 Specifications

Epson

Epson 4180 - Perfection Photo Product support bulletin

Radio Shack

Radio Shack PRO-72 owner's manual

Lanier

Lanier 5622 Operator's guide

Faro

Faro Freestyle 2 user manual

Kramer

Kramer VS-16N user manual

Z/I Imaging

Z/I Imaging PhotoScan 2001 instructions

Renkforce

Renkforce DS100-5M operating instructions

Canon

Canon imageFORMULA CR-120N user manual

Fujitsu

Fujitsu FI-4860C2 Specifications

HPc9861a

HPc9861a 4400c Setup and support guide

Kodak

Kodak i5800 Scanner Brochure & specs

Kodak

Kodak i7300 user guide

Revopoint

Revopoint POP user manual

Fujitsu

Fujitsu fi-4860C installation guide

POSIFLEX CD-3200 Setup guide

Popular Scanner manuals by other brands